| Common Name: | EPOXY GEL SYRINGE BREAK OFF TIP (48) - RESIN, EPOXY GEL SYRINGE BREAK OFF TIP (4 |
| Manufacturer: | PACER TECHNOLOGY |
| SDS Revision Date: | 11/6/2017 |
| SDS Format: | GHS-US |
| Item Number(s): | 1FBH1 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
AC MARCA
PACER TECHNOLOGY
SAFETY DATA SHEET
DATE PREPARED: 05/10/2016
MSDS NO: 11710121_15213 - RESIN
DATE-REVISED: 11/06/2017
REVISION NO: 9
| 1. PRODUCT AND COMPANY IDENTIFICATION |  |
PRODUCT DESCRIPTION: EPOXY GEL SYRINGE BREAK OFF TIP (48) - RESIN
MANUFACTURER:
PACER TECHNOLOGY
3281 E. GUASTI RD., SUITE 260
ONTARIO, CA 91761
EMERGENCY CONTACT: CHEMTREC
EMERGENCY PHONE: 800-424-9300
ALTERNATE EMERGENCY PHONE: 703-527-3887
PRODUCT STEWARDSHIP: 909-987-0550
| 2. HAZARDS IDENTIFICATION | |
GHS CLASSIFICATIONS:
HEALTH:
SKIN IRRITATION, CATEGORY 2
EYE IRRITATION, CATEGORY 2B
SKIN SENSITIZATION, CATEGORY 1B
REPRODUCTIVE TOXICITY, CATEGORY 2
GHS LABEL ELEMENTS:
NOTE:
IF THIS PRODUCT IS A CONSUMER PRODUCT IT IS LABELED IN ACCORDANCE WITH THE
CONSUMER PRODUCT SAFETY COMMISSION REGULATIONS AND NOT OSHA REGULATIONS.
THE REQUIREMENTS FOR THE LABELING OF CONSUMER PRODUCTS TAKE PRECEDENCE OVER
OSHA LABELING SO THE ACTUAL PRODUCT LABEL WILL NOT CONTAIN THE OSHA LABEL
ELEMENTS SHOWN BELOW ON THIS SDS.
EXCLAMATION MARK
HEALTH HAZARD
SIGNAL WORD: WARNING
HAZARD STATEMENTS:
H315: CAUSES SKIN IRRITATION.
H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
H319: CAUSES SERIOUS EYE IRRITATION.
H361:
SUSPECTED OF DAMAGING FERTILITY OR THE UNBORN CHILD (STATE SPECIFIC EFFECT
IF KNOWN)(STATE ROUTE OF EXPOSURE IF IT IS CONCLUSIVELY PROVEN THAT NO
OTHER ROUTES OF EXPOSURE CAUSE THE HAZARD).
PRECAUTIONARY STATEMENT(S):
PREVENTION:
P261: AVOID BREATHING DUST/FUME/GAS/MIST/VAPOURS/SPRAY.
P264: WASH SKIN AND HANDS THOROUGHLY AFTER HANDLING.
P272:
CONTAMINATED WORK CLOTHING SHOULD NOT BE ALLOWED OUT OF THE WORKPLACE.
P273: AVOID RELEASE TO THE ENVIRONMENT.
P280:
WEAR PROTECTIVE GLOVES/PROTECTIVE CLOTHING/EYE PROTECTION/FACE PROTECTION.
P362: TAKE OFF CONTAMINATED CLOTHING.
P363: WASH CONTAMINATED CLOTHING BEFORE REUSE.
P391: COLLECT SPILLAGE.
RESPONSE:
P305+P351+P338:
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES, IF
PRESENT AND EASY TO DO. CONTINUE RINSING.
P313: GET MEDICAL ADVICE/ATTENTION.
P302+P352:
IF ON SKIN: WASH WITH PLENTY OF SOAP AND WATER.
P333+P313:
IF SKIN IRRITATION OR RASH OCCURS: GET MEDICAL ADVICE/ATTENTION.
STORAGE:
P403+P235: STORE IN A WELL-VENTILATED PLACE. KEEP COOL.
DISPOSAL:
P501:
DISPOSE OF IN A MANNER CONSISTENT WITH FEDERAL, STATE, AND LOCAL
REGULATIONS.
| 3. COMPOSITION / INFORMATION ON INGREDIENTS | |
CHEMICAL NAME WT.% CAS
EPOXY RESIN (BISPHENOL A) 90 - 100 25068-38-6
| 4. FIRST AID MEASURES | |
EYES:
IMMEDIATELY FLUSH WITH PLENTY OF WATER. AFTER INITIAL FLUSHING, REMOVE ANY
CONTACT LENSES AND CONTINUE FLUSHING FOR AT LEAST 15 MINUTES. HAVE EYES
EXAMINED AND TESTED BY MEDICAL PERSONNEL.
SKIN:
IMMEDIATELY WASH SKIN WITH SOAP AND PLENTY OF WATER. REMOVE CONTAMINATED
CLOTHING. GET MEDICAL ATTENTION IF SYMPTOMS REOCCUR. WASH CLOTHING BEFORE
REUSE.
INGESTION:
IF SWALLOWED, DO NOT INDUCE VOMITING. KEEP INDIVIDUAL CALM. GET MEDICAL
ATTENTION AND SHOW CONTAINER LABEL.
INHALATION:
REMOVE TO FRESH AIR. IF NOT BREATHING, GIVE ARTIFICIAL RESPIRATION. IF
BREATHING IS DIFFICULT, GIVE OXYGEN. GET MEDICAL ATTENTION.
SIGNS AND SYMPTOMS OF OVEREXPOSURE:
EYES: CAUSES EYE IRRITATION.
SKIN:
IRRITATING TO SKIN. MAY CAUSE ALLERGIC SKIN REACTION WITH PROLONGED
CONTACT.
SKIN ABSORPTION:
THIS MATERIAL IS A WATER POLLUTANT AND SHOULD BE PREVENTED FROM
CONTAMINATING SOIL OR FROM ENTERING SEWAGE AND DRAINAGE SYSTEMS AND BODIES
OF WATER.
INGESTION: MAY BE IRRITATING. SEEK MEDICAL ADVICE.
INHALATION:
PROLONGED OR EXCESSIVE INHALATION MAY CAUSE RESPIRATORY TRACT IRRITATION.
ACUTE EFFECTS: SLIGHTLY IRRITATING TO EYES AND RESPIRATORY TRACTS.
CHRONIC EFFECTS:
FREQUENT OR PROLONGED CONTACT MAY IRRITATE THE SKIN AND CAUSE A SKIN RASH
(DERMATITIS).
| 5. FIRE FIGHTING MEASURES | |
FLAMMABLE CLASS: NOT FLAMMABLE
EXTINGUISHING MEDIA:
USE ALCOHOL FOAM, CARBON DIOXIDE, OR WATER SPRAY WHEN FIGHTING FIRES
INVOLVING THIS MATERIAL.
HAZARDOUS COMBUSTION PRODUCTS:
COMBUSTION PRODUCTS MAY INCLUDE AND ARE NOT LIMITED TO: CARBON MONOXIDE,
CARBON DIOXIDE AND PHENOLICS.
FIRE FIGHTING PROCEDURES:
USE WATER SPRAY TO KEEP FIRE-EXPOSED CONTAINERS COOL AND TO KNOCK DOWN
VAPORS WHICH MAY RESULT FROM PRODUCT DECOMPOSITION.
FIRE FIGHTING EQUIPMENT:
AS IN ANY FIRE, WEAR SELF-CONTAINED BREATHING APPARATUS PRESSURE-DEMAND,
(MSHA/NIOSH APPROVED OR EQUIVALENT) AND FULL PROTECTIVE GEAR.
HAZARDOUS DECOMPOSITION PRODUCTS:
CARBON DIOXIDE, CARBON MONOXIDE AND OTHER TOXIC OR IRRITATING COMPOUNDS MAY
FORM WHEN HEATED TO DECOMPOSITION.
| 6. ACCIDENTAL RELEASE MEASURES | |
GENERAL PROCEDURES:
CONTAIN SPILLED MATERIAL IF POSSIBLE. ABSORB WITH MATERIALS SUCH AS: SAND.
POLYPROPYLENE FIBER PRODUCTS. POLYETHYLENE FIBER PRODUCTS. REMOVE RESIDUAL
WITH SOAP AND HOT WATER. COLLECT IN SUITABLE AND PROPERLY LABELED
CONTAINERS. RESIDUAL CAN BE REMOVED WITH SOLVENT. SOLVENTS ARE NOT
RECOMMENDED FOR CLEAN-UP UNLESS THE RECOMMENDED EXPOSURE GUIDELINES AND
SAFE HANDLING PRACTICES FOR THE SPECIFIC SOLVENT ARE FOLLOWED. CONSULT
APPROPRIATE SOLVENT SAFETY DATA SHEET FOR HANDLING INFORMATION.
COMMENTS:
THIS MATERIAL IS A WATER POLLUTANT AND SHOULD BE PREVENTED FROM
CONTAMINATING SOIL OR FROM ENTERING SEWAGE AND DRAINAGE SYSTEMS AND BODIES
OF WATER.
| 7. HANDLING AND STORAGE | |
GENERAL PROCEDURES:
USE WITH ADEQUATE VENTILATION. AVOID CONTACT WITH EYES, SKIN AND CLOTHING.
HANDLING:
AVOID BREATHING (DUST, VAPOR, MIST, GAS). AVOID CONTACT WITH SKIN, EYES AND
CLOTHING. KEEP CONTAINER CLOSED WHEN NOT IN USE.
STORAGE:
STORE IN A COOL PLACE IN ORIGINAL CONTAINER AND PROTECT FROM SUNLIGHT. KEEP
AWAY FROM SOURCES OF IGNITION.
STORAGE TEMPERATURE: AMBIENT ROOM TEMPERATURE (70F/21C).
LOADING TEMPERATURE: NOT DETERMINED
LOADING/UNLOADING VISCOSITY: NOT DETERMINED
STORAGE PRESSURE: NOT DETERMINED
| 8. EXPOSURE CONTROLS / PERSONAL PROTECTION | |
ENGINEERING CONTROLS:
USE LOCAL EXHAUST VENTILATION, OR OTHER ENGINEERING CONTROLS TO MAINTAIN
AIRBORNE LEVELS BELOW EXPOSURE LIMIT REQUIREMENTS OR GUIDELINES. IF THERE
ARE NO APPLICABLE EXPOSURE LIMIT REQUIREMENTS OR GUIDELINES, GENERAL
VENTILATION SHOULD BE SUFFICIENT FOR MOST OPERATIONS. LOCAL EXHAUST
VENTILATION MAY BE NECESSARY FOR SOME OPERATIONS.
PERSONAL PROTECTIVE EQUIPMENT:
EYES AND FACE:
FOR NORMAL CONDITIONS, WEAR SAFETY GLASSES. WHERE THERE IS REASONABLE
PROBABILITY OF LIQUID CONTACT, WEAR SPLASH-PROOF GOGGLES.
SKIN: WEAR RUBBER GLOVES TO AVOID PROLONGED SKIN CONTACT.
RESPIRATORY: USE ONLY IN A WELL VENTILATED AREA.
PROTECTIVE CLOTHING: WEAR RUBBER GLOVES & APRON.
WORK HYGIENIC PRACTICES:
AVOID CONTACT WITH SKIN AND EYES. WASH THOROUGHLY AFTER HANDLING.
| 9. PHYSICAL AND CHEMICAL PROPERTIES | |
PHYSICAL STATE: VISCOUS LIQUID.
ODOR: MILD ODOR.
ODOR THRESHOLD: NO DATA AVAILABLE
APPEARANCE: PASTE.
COLOR: GREEN.
PH: NO DATA AVAILABLE
PERCENT VOLATILE: NO DATA AVAILABLE
FLASHPOINT AND METHOD:
264 DEG. C (507 DEG. F) TO 268 DEG. C (514 DEG. F) CC - CLOSED CUP
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
VAPOR PRESSURE: NO DATA AVAILABLE
VAPOR DENSITY: NO DATA AVAILABLE
BOILING POINT: NO DATA AVAILABLE
FREEZING POINT: NO DATA AVAILABLE
MELTING POINT: NO DATA AVAILABLE
POUR POINT: NO DATA AVAILABLE
THERMAL DECOMPOSITION: NO DATA AVAILABLE
SOLUBILITY IN WATER: 5.4 TO 8.4 MG/L AT 20 DEG. C (68 DEG. F)
EVAPORATION RATE: NO DATA AVAILABLE
DENSITY: 1.16 G/CM3 AT 25C (77F)
SPECIFIC GRAVITY: 1.16
VISCOSITY #1: 10000 TO 20000 MPA. S. AT 25 DEG. C (77 DEG. F)
MOLECULAR WEIGHT: NO DATA AVAILABLE
(VOC): 0 G/L
| 10. STABILITY AND REACTIVITY | |
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR.
STABILITY: STABLE
CONDITIONS TO AVOID: AVOID TEMPERATURES ABOVE (300) F (148) C.
HAZARDOUS DECOMPOSITION PRODUCTS:
CARBON MONOXIDE, ALDEHYDES, ACIDS AND OTHER ORGANIC SUBSTANCES MAY BE
FORMED DURING COMBUSTION (>500F) TEMPERATURE DEGRADATION.
INCOMPATIBLE MATERIALS:
STRONG ACIDS, OXIDIZING AGENTS, MINERAL AND ORGANIC BASES, AND ESPECIALLY
ALIPHATIC AMINES.
| 11. TOXICOLOGICAL INFORMATION | |
ACUTE TOXICITY:
CHEMICAL NAME ORAL LD50 (RAT) DERMAL LD50 (RABBIT)
EPOXY RESIN (BISPHENOL A) >2000 MG/KG (RAT) >2000 MG/KG (RAT)
DERMAL LD50: 23000 MG/KG (RABBIT)
ORAL LD50: > 15000 ML/KG (RAT)
SERIOUS EYE DAMAGE/IRRITATION:
PROLONGED OR REPEATED SKIN CONTACT MAY CAUSE IRRITATION.
RESPIRATORY OR SKIN SENSITIZATION: MAY CAUSE SENSITIZATION.
GERM CELL MUTAGENICITY:
IN VITRO GENETIC TOXICITY STUDIES WERE NEGATIVE IN SOME CASES AND POSITIVE
IN OTHER CASES. ANIMAL GENETIC TOXICITY STUDIES WERE NEGATIVE.
CARCINOGENICITY:
IARC: NOT LISTED.
NTP: NOT LISTED.
OSHA: NOT LISTED.
REPRODUCTIVE TOXICITY:
IN ANIMAL STUDIES, DID NOT INTERFERE WITH REPRODUCTION.
| 12. ECOLOGICAL INFORMATION | |
ENVIRONMENTAL DATA: DO NOT FLUSH TO SEWER.
ECOTOXICOLOGICAL INFORMATION:
RAINBOW TROUT LC50, SEMI-STATIC TEST, 96 H: 2 MG/L; WATER FLEA EC50, STATIC
TEST, 48 H, IMMOBILIZATION: 1.8 MG/L; BACTERIA IC50, 18 H: >42.6 MG/L.
BIOACCUMULATION/ACCUMULATION:
BIOCONCENTRATION POTENTIAL IS MODERATE (BCF 100 TO 3000 OR LOG POW 3 TO 5).
AQUATIC TOXICITY (ACUTE):
NOTES:
MATERIAL IS TOXIC TO AQUATIC ORGANISMS (LC50 BETWEEN 1 AND 10 MG/L IN THE
MOST SENSITIVE SPECIES).
| 13. DISPOSAL CONSIDERATIONS | |
DISPOSAL METHOD:
DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE, AND FEDERAL REGULATIONS.
| 14. TRANSPORT INFORMATION | |
DOT (DEPARTMENT OF TRANSPORTATION):
PROPER SHIPPING NAME: NOT REGULATED PER 49 CFR 173.9
AIR (ICAO/IATA):
SHIPPING NAME: UN3316, CHEMICAL KIT, 9, III
VESSEL (IMO/IMDG):
SHIPPING NAME: UN3316, CHEMICAL KIT, 9, III
COMMENTS:
THE TRANSPORT INFORMATION PROVIDED IN THIS SECTION ONLY APPLIES TO
THE MATERIAL FORMULATION/ITSELF, AND IS NOT SPECIFIC TO ANY PACKAGE/
CONFIGURATION. THIS INFORMATION IS NOT INTENDED TO CONVEY ALL SPECIFIC
REGULATORY OR OPERATIONAL REQUIREMENTS/INFORMATION RELATING TO THIS
PRODUCT. TRANSPORTATION CLASSIFICATIONS MAY VARY BY CONTAINER VOLUME
AND MAY BE INFLUENCED BY REGIONAL OR COUNTRY VARIATIONS IN REGULATIONS.
IT IS THE RESPONSIBILITY OF THE TRANSPORTING ORGANIZATIONS TO FOLLOW ALL
APPLICABLE LAWS, REGULATIONS, AND RULES RELATING TO THE TRANSPORTATION OF
THE MATERIAL.
| 15. REGULATORY INFORMATION | |
UNITED STATES:
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
FIRE: NO
PRESSURE GENERATING: NO
REACTIVITY: NO
ACUTE: YES
CHRONIC: NO
TITLE III NOTES:
TO THE BEST OF OUR KNOWLEDGE, THIS PRODUCT DOES NOT CONTAIN CHEMICALS AT
LEVELS WHICH REQUIRE REPORTING UNDER THIS STATUTE.
TSCA (TOXIC SUBSTANCE CONTROL ACT):
CHEMICAL NAME CAS
EPOXY RESIN (BISPHENOL A) 25068-38-6
TSCA STATUS: ALL INGREDIENTS IN THIS MIXTURE ARE IN COMPLIANCE WITH TSCA.
CALIFORNIA PROPOSITION 65:
WARNING:
THIS PRODUCT CAN EXPOSE YOU TO CHEMICALS INCLUDING BISPHENOL A, WHICH IS
KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER
REPRODUCTIVE HARM. FOR MORE INFORMATION GO TO WWW.P65WARNINGS.CA.GOV.
CHEMICAL NAME WT.% LISTED
EPOXY RESIN (BISPHENOL A) 90 - 100 FEMALE REPRODUCTIVE
| 16. OTHER INFORMATION | |
APPROVED BY: PACER TECHNOLOGY REGULATORY DEPARTMENT
PREPARED BY: PACER TECHNOLOGY REGULATORY DEPARTMENT
DATE-REVISED: 11/06/2017
REVISION SUMMARY: THIS MSDS REPLACES THE 09/14/2017 MSDS.
HMIS RATING:
HEALTH 1
FLAMMABILITY 1
PHYSICAL HAZARD 0
PERSONAL PROTECTION
NFPA CODES:
1
1
0
MANUFACTURER DISCLAIMER:
TO THE BEST OF OUR KNOWLEDGE, THE INFORMATION CONTAINED HEREIN IS ACCURATE.
HOWEVER, PACER TECHNOLOGY DOES NOT ASSUME ANY LIABILITY FOR THE ACCURACY OR
COMPLETENESS OF THE INFORMATION CONTAINED HEREIN. FINAL DETERMINATION OF
SUITABILITY OF ANY MATERIAL IS THE SOLE RESPONSIBILITY OF THE USER. ALL
MATERIALS MAY PRESENT UNKNOWN HAZARDS AND SHOULD BE USED WITH CAUTION.
ALTHOUGH CERTAIN HAZARDS ARE DESCRIBED HEREIN, WE CANNOT GUARANTEE THAT
THESE ARE THE ONLY HAZARDS WHICH EXIST.
AC MARCA
PACER TECHNOLOGY
SAFETY DATA SHEET
DATE PREPARED: 11/25/2013
MSDS NO: 11710121_15213 - HARDENER
DATE-REVISED: 08/09/2017
REVISION NO: 7
| 1. PRODUCT AND COMPANY IDENTIFICATION | |
PRODUCT DESCRIPTION: EPOXY GEL SYRINGE BREAK OFF TIP (48) - HARDENER
MANUFACTURER:
PACER TECHNOLOGY
3281 E. GUASTI RD., SUITE 260
ONTARIO, CA 91761
EMERGENCY CONTACT: CHEMTREC
EMERGENCY PHONE: 800-424-9300
ALTERNATE EMERGENCY PHONE: 703-527-3887
PRODUCT STEWARDSHIP: 909-987-0550
| 2. HAZARDS IDENTIFICATION | |
GHS CLASSIFICATIONS:
HEALTH:
SKIN CORROSION/IRRITATION, CATEGORY 1C
SERIOUS EYE DAMAGE/EYE IRRITATION, CATEGORY 1
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE):
ORAL [BRAIN], CATEGORY 2
GHS LABEL ELEMENTS:
NOTE:
IF THIS PRODUCT IS A CONSUMER PRODUCT IT IS LABELED IN ACCORDANCE WITH THE
CONSUMER PRODUCT SAFETY COMMISSION REGULATIONS AND NOT OSHA REGULATIONS.
THE REQUIREMENTS FOR THE LABELING OF CONSUMER PRODUCTS TAKE PRECEDENCE OVER
OSHA LABELING SO THE ACTUAL PRODUCT LABEL WILL NOT CONTAIN THE OSHA LABEL
ELEMENTS SHOWN BELOW ON THIS SDS.
CORROSION
HEALTH HAZARD
SIGNAL WORD: DANGER
HAZARD STATEMENTS:
H302: HARMFUL IF SWALLOWED.
H314: CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
H315: CAUSES SKIN IRRITATION.
H319: CAUSES SERIOUS EYE IRRITATION.
H373:
MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE IF
SWALLOWED. (BRAIN)
PRECAUTIONARY STATEMENT(S):
PREVENTION:
P264: WASH SKIN AND HANDS THOROUGHLY AFTER HANDLING.
P270: DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT.
P280:
WEAR PROTECTIVE GLOVES/PROTECTIVE CLOTHING/EYE PROTECTION/FACE PROTECTION.
P362: TAKE OFF CONTAMINATED CLOTHING.
RESPONSE:
P301+312:
IF SWALLOWED: CALL A POISON CENTER OR DOCTOR/PHYSICIAN IF YOU FEEL UNWELL.
P302+352:
IF ON SKIN: WASH WITH PLENTY OF SOAP AND WATER.
P305+P351+P338:
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES, IF
PRESENT AND EASY TO DO. CONTINUE RINSING.
P332+P313:
IF SKIN IRRITATION OCCURS: GET MEDICAL ADVICE/ATTENTION.
P337+P313:
IF EYE IRRITATION PERSISTS: GET MEDICAL ADVICE/ATTENTION.
STORAGE:
P403+P233: STORE IN A WELL-VENTILATED PLACE. KEEP CONTAINER TIGHTLY CLOSED.
DISPOSAL:
P501:
DISPOSE OF IN A MANNER CONSISTENT WITH FEDERAL, STATE, AND LOCAL
REGULATIONS.
| 3. COMPOSITION / INFORMATION ON INGREDIENTS | |
CHEMICAL NAME WT.% CAS
MERCAPTAN/AMINE POLYMER SYSTEM 85 - 100
2,4,6-TRIS(DIMETHYLAMINOMETHYL)PHENOL 3 - 7 90-72-2
BIS(DIMETHYLAMINO)METHYL PHENOL 1 - 5 71074-89-0
| 4. FIRST AID MEASURES | |
EYES:
IMMEDIATELY FLUSH WITH PLENTY OF WATER. AFTER INITIAL FLUSHING, REMOVE ANY
CONTACT LENSES AND CONTINUE FLUSHING FOR AT LEAST 15 MINUTES. HAVE EYES
EXAMINED AND TESTED BY MEDICAL PERSONNEL.
SKIN:
WASH WITH SOAP AND WATER. GET MEDICAL ATTENTION IF IRRITATION DEVELOPS OR
PERSISTS.
INGESTION: DO NOT INDUCE VOMITING. CONTACT PHYSICIAN AT ONCE.
INHALATION:
REMOVE TO FRESH AIR. GET MEDICAL ATTENTION IF BREATHING IS DIFFICULT.
SIGNS AND SYMPTOMS OF OVEREXPOSURE:
EYES: CAUSES SERIOUS EYE DAMAGE.
SKIN: CAUSES SEVERE BURNS.
SKIN ABSORPTION: NO DATA AVAILABLE
INGESTION:
INGESTION OF THIS MATERIAL CAN CAUSE MOUTH, THROAT, ESOPHAGEAL, AND
GASTROINTESTINAL TRACT IRRITATION.
INHALATION:
PROLONGED OR EXCESSIVE INHALATION MAY CAUSE RESPIRATORY TRACT IRRITATION.
ACUTE EFFECTS: SLIGHTLY IRRITATING TO EYES AND RESPIRATORY TRACTS.
CHRONIC EFFECTS:
AVOID CONTACT WITH EYES; MAY CAUSE REDNESS, IRRITATION AND CONJUNCTIVITIS.
| 5. FIRE FIGHTING MEASURES | |
FLAMMABLE CLASS: NOT FLAMMABLE
EXTINGUISHING MEDIA: WATER SPRAY, FOAM, CARBON DIOXIDE, DRY CHEMICALS.
HAZARDOUS COMBUSTION PRODUCTS: CAN BURN IN FIRE, RELEASING TOXIC VAPORS.
EXPLOSION HAZARDS: NONE KNOWN.
FIRE FIGHTING PROCEDURES:
FIREFIGHTERS SHOULD WEAR SELF-CONTAINED BREATHING APPARATUS AND PROTECTIVE
CLOTHING.
FIRE FIGHTING EQUIPMENT:
AS IN ANY FIRE, WEAR SELF-CONTAINED BREATHING APPARATUS PRESSURE-DEMAND,
(MSHA/NIOSH APPROVED OR EQUIVALENT) AND FULL PROTECTIVE GEAR.
FIRE EXPLOSION: NONE KNOWN.
SENSITIVE TO STATIC DISCHARGE: NO DATA AVAILABLE
SENSITIVITY TO IMPACT: NO DATA AVAILABLE
HAZARDOUS DECOMPOSITION PRODUCTS: CARBON MONOXIDE OR CARBON DIOXIDE.
| 6. ACCIDENTAL RELEASE MEASURES | |
SMALL SPILL:
SCRAPE AS MUCH MATERIAL AS YOU CAN FROM THE SURFACE USING A STIFF METAL OR
PLASTIC SCRAPER. CLEAN THE RESIDUE WITH ACETONE OR ALCOHOL AND PLACE IN A
DISPOSABLE CONTAINER.
LARGE SPILL:
PREVENT CONTAMINATION OF SOIL, DRAINS AND SURFACE WATERS. DIKE AND CONTAIN
MATERIAL. SOAK UP RESIDUE WITH ABSORBENT (CLAY, SAND) MATERIALS AND DISPOSE
OF PROPERLY.
ENVIRONMENTAL PRECAUTIONS:
WATER SPILL:
AVOID DISPERSAL OF SPILLED MATERIAL AND RUNOFF AND CONTACT WITH SOIL,
WATERWAYS, DRAINS, AND SEWERS. INFORM THE RELEVANT AUTHORITIES IF THE
PRODUCT HAS CAUSED ENVIRONMENTAL POLLUTION (SEWERS, WATERWAYS, SOIL OR
AIR).
GENERAL PROCEDURES:
POLYMERIZE WITH WATER. INCREASE VENTILATION TO AREA. SOLID MATERIAL MAY BE
SCRAPED FROM SURFACE.
| 7. HANDLING AND STORAGE | |
GENERAL PROCEDURES:
USE WITH ADEQUATE VENTILATION. AVOID CONTACT WITH EYES, SKIN AND CLOTHING.
HANDLING:
AVOID BREATHING (DUST, VAPOR, MIST, GAS). AVOID CONTACT WITH SKIN, EYES,
AND CLOTHING. KEEP CONTAINER CLOSED WHEN NOT IN USE.
STORAGE:
STORE IN A COOL PLACE IN ORIGINAL CONTAINER AND PROTECT FROM SUNLIGHT. KEEP
AWAY FROM SOURCES OF IGNITION.
STORAGE TEMPERATURE: AMBIENT ROOM TEMPERATURE (70F/21C).
LOADING TEMPERATURE: NO DATA AVAILABLE
| 8. EXPOSURE CONTROLS / PERSONAL PROTECTION | |
ENGINEERING CONTROLS:
USE PROCESS ENCLOSURES, LOCAL EXHAUST VENTILATION, OR OTHER ENGINEERING
CONTROLS TO CONTROL AIRBORNE LEVELS BELOW RECOMMENDED EXPOSURE LIMITS.
PERSONAL PROTECTIVE EQUIPMENT:
EYES AND FACE:
FOR NORMAL CONDITIONS, WEAR SAFETY GLASSES. WHERE THERE IS REASONABLE
PROBABILITY OF LIQUID CONTACT, WEAR SPLASH-PROOF GOGGLES.
SKIN: WEAR SUITABLE PROTECTIVE CLOTHING AND GLOVES.
RESPIRATORY:
USE ONLY IN A WELL-VENTILATED AREA. IN CASE OF INSUFFICIENT VENTILATION,
WEAR SUITABLE RESPIRATORY EQUIPMENT.
RECOMMENDED:
FULL-FACE NIOSH-APPROVED RESPIRATOR WITH ORGANIC VAPOR CARTRIDGE.
PROTECTIVE CLOTHING:
WEAR PROTECTIVE CLOTHING. LAUNDER CONTAMINATED CLOTHING BEFORE REUSE.
WORK HYGIENIC PRACTICES:
AVOID CONTACT WITH SKIN AND EYES. WASH THOROUGHLY AFTER HANDLING.
| 9. PHYSICAL AND CHEMICAL PROPERTIES | |
PHYSICAL STATE: LIQUID. [PASTE].
ODOR: EPOXY ODOR.
ODOR THRESHOLD: NO DATA AVAILABLE
APPEARANCE: LIGHT YELLOW VISCOUS LIQUID.
PH: NO DATA AVAILABLE
PERCENT VOLATILE: NO DATA AVAILABLE
FLASHPOINT AND METHOD: >93.33 DEG. C (200 DEG. F) CLOSED CUP [ESTIMATED]
FLAMMABLE LIMITS: NO DATA AVAILABLE
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
VAPOR PRESSURE: NO DATA AVAILABLE
VAPOR DENSITY: NO DATA AVAILABLE
BOILING POINT: NO DATA AVAILABLE
FREEZING POINT: NO DATA AVAILABLE
MELTING POINT: NO DATA AVAILABLE
POUR POINT: NO DATA AVAILABLE
THERMAL DECOMPOSITION: NO DATA AVAILABLE
SOLUBILITY IN WATER: SLIGHT
EVAPORATION RATE: <0.01 (BUTYL ACETATE =1)
DENSITY: NO DATA AVAILABLE
SPECIFIC GRAVITY: 1.16
MOLECULAR WEIGHT: NO DATA AVAILABLE
(VOC): 0 G/L
| 10. STABILITY AND REACTIVITY | |
STABILITY: STABLE
POSSIBILITY OF HAZARDOUS REACTIONS:
UNDER NORMAL CONDITIONS OF STORAGE AND USE, HAZARDOUS REACTIONS WILL NOT
OCCUR.
HAZARDOUS DECOMPOSITION PRODUCTS:
UNDER NORMAL CONDITIONS OF STORAGE AND USE, HAZARDOUS DECOMPOSITION
PRODUCTS SHOULD NOT BE PRODUCED.
INCOMPATIBLE MATERIALS: STRONG OXIDIZING AGENTS, ACIDS AND BASES.
| 11. TOXICOLOGICAL INFORMATION | |
ACUTE TOXICITY:
CHEMICAL NAME ORAL LD50 (RAT) DERMAL LD50 (RABBIT)
2,4,6-TRIS(DIMETHYL- 2169 MG/KG (RAT) >971 MG/KG (RAT)
AMINOMETHYL)PHENOL
DERMAL LD50: >971 MG/KG (RAT)
ORAL LD50: 2169 MG/KG (RAT)
NOTES:
PRODUCT IS MODERATELY IRRITATING TO EYES AND SKIN. CONTACT WITH PRODUCT AT
ELEVATED TEMPERATURES CAN RESULT IN THERMAL BURNS. PRODUCT MAY CAUSE SKIN
SENSITIZATION IN SUSCEPTIBLE INDIVIDUALS; OVEREXPOSURE EFFECTS MAY BE
SKIN/EYE IRRITATION AND ALLERGIC SKIN REACTIONS.
RESPIRATORY OR SKIN SENSITIZATION:
IRRITATING TO SKIN. MAY CAUSE ALLERGIC SKIN REACTION WITH PROLONGED
CONTACT.
GERM CELL MUTAGENICITY: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
CARCINOGENICITY:
IARC: NOT LISTED.
NTP: NOT LISTED.
OSHA: NOT LISTED.
NOTES: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
REPRODUCTIVE TOXICITY: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
STOT-SINGLE EXPOSURE: NO DATA AVAILABLE
STOT-REPEATED EXPOSURE:
MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE IF
SWALLOWED. (BRAIN)
| 12. ECOLOGICAL INFORMATION | |
ENVIRONMENTAL DATA:
PREVENT PRODUCT FROM ENTERING DRAINS OR SEWERS IN CASE OF SPILL.
| 13. DISPOSAL CONSIDERATIONS | |
DISPOSAL METHOD:
DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE, AND FEDERAL REGULATIONS.
| 14. TRANSPORT INFORMATION | |
DOT (DEPARTMENT OF TRANSPORTATION):
PROPER SHIPPING NAME: UN3316, CHEMICAL KIT, 9, III
AIR (ICAO/IATA):
SHIPPING NAME: UN3316, CHEMICAL KIT, 9, III
VESSEL (IMO/IMDG):
SHIPPING NAME: UN3316, CHEMICAL KIT, 9, III
COMMENTS:
THE TRANSPORT INFORMATION PROVIDED IN THIS SECTION ONLY APPLIES TO
THE MATERIAL FORMULATION/ITSELF, AND IS NOT SPECIFIC TO ANY PACKAGE/
CONFIGURATION. THIS INFORMATION IS NOT INTENDED TO CONVEY ALL SPECIFIC
REGULATORY OR OPERATIONAL REQUIREMENTS/INFORMATION RELATING TO THIS
PRODUCT. TRANSPORTATION CLASSIFICATIONS MAY VARY BY CONTAINER VOLUME
AND MAY BE INFLUENCED BY REGIONAL OR COUNTRY VARIATIONS IN REGULATIONS.
IT IS THE RESPONSIBILITY OF THE TRANSPORTING ORGANIZATIONS TO FOLLOW ALL
APPLICABLE LAWS, REGULATIONS, AND RULES RELATING TO THE TRANSPORTATION OF
THE MATERIAL.
| 15. REGULATORY INFORMATION | |
UNITED STATES:
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
FIRE: NO
PRESSURE GENERATING: NO
REACTIVITY: NO
ACUTE: YES
CHRONIC: NO
TSCA (TOXIC SUBSTANCE CONTROL ACT);
CHEMICAL NAME CAS
MERCAPTAN/AMINE POLYMER SYSTEM
2,4,6-TRIS(DIMETHYLAMINOMETHYL)PHENOL 90-72-2
BIS(DIMETHYLAMINO)METHYL PHENOL 71074-89-0
| 16. OTHER INFORMATION | |
APPROVED BY: PACER TECHNOLOGY REGULATORY DEPARTMENT
PREPARED BY: PACER TECHNOLOGY REGULATORY DEPARTMENT
DATE-REVISED: 08/09/2017
REVISION SUMMARY:
THIS MSDS REPLACES THE 01/31/2017 MSDS. REVISED: SECTION 1: MSDS NO.
SECTION 14: AIR (ICAO/IATA) - SHIPPING NAME COMMENTS, DOT (DEPARTMENT OF
TRANSPORTATION) - PROPER SHIPPING NAME VESSEL (IMO/IMDG) - SHIPPING NAME.
HMIS RATING:
HEALTH 3
FLAMMABILITY 1
PHYSICAL HAZARD 0
PERSONAL PROTECTION
NFPA CODES:
3
1
0
MANUFACTURER DISCLAIMER:
TO THE BEST OF OUR KNOWLEDGE, THE INFORMATION CONTAINED HEREIN IS ACCURATE.
HOWEVER, BARNES DISTRIBUTION DOES NOT ASSUME ANY LIABILITY FOR THE ACCURACY
OR COMPLETENESS OF THE INFORMATION CONTAINED HEREIN. FINAL DETERMINATION OF
SUITABILITY OF ANY MATERIAL IS THE SOLE RESPONSIBILITY OF THE USER. ALL
MATERIALS MAY PRESENT UNKNOWN HAZARDS AND SHOULD BE USED WITH CAUTION.
ALTHOUGH CERTAIN HAZARDS ARE DESCRIBED HEREIN, WE CANNOT GUARANTEE THAT
THESE ARE THE ONLY HAZARDS THAT EXIST.