| Common Name: | 3535 PAINT HARDENER, 00384794 |
| Manufacturer: | PPG INDUSTRIES |
| SDS Revision Date: | 11/16/2019 |
| SDS Format: | GHS-US |
| Item Number(s): | 2AJN4 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
PPG
SAFETY DATA SHEET
DATE OF ISSUE/DATE OF REVISION: 16 NOVEMBER 2019
VERSION: 1.04
| SECTION 1. IDENTIFICATION |  |
PRODUCT NAME: 3535 PAINT HARDENER
PRODUCT CODE: 00384794
OTHER MEANS OF IDENTIFICATION: NOT AVAILABLE.
PRODUCT TYPE: POWDER.
RELEVANT IDENTIFIED USES OF THE SUBSTANCE OR MIXTURE AND USES ADVISED
AGAINST:
PRODUCT USE: INDUSTRIAL APPLICATIONS.
USE OF THE SUBSTANCE/MIXTURE: HARDENER.
USES ADVISED AGAINST: NOT APPLICABLE.
MANUFACTURER:
PPG INDUSTRIES, INC.
ONE PPG PLACE
PITTSBURGH, PA 15272
EMERGENCY TELEPHONE NUMBER:
(412) 434-4515 (U.S.)
(514) 645-1320 (CANADA)
01-800-00-21-400 OR +52 55 5559 1588 (MEXICO)
TECHNICAL PHONE NUMBER: 1-800-441-9695 (8:00 AM TO 5:00 PM EST)
| SECTION 2. HAZARDS IDENTIFICATION | |
OSHA/HCS STATUS:
THIS MATERIAL IS CONSIDERED HAZARDOUS BY THE OSHA HAZARD COMMUNICATION
STANDARD (29 CFR 1910.1200).
CLASSIFICATION OF THE SUBSTANCE OR MIXTURE:
COMBUSTIBLE DUSTS
EYE IRRITATION: CATEGORY 2A
PERCENTAGE OF THE MIXTURE CONSISTING OF INGREDIENT(S) OF UNKNOWN ACUTE
TOXICITY: 100% (DERMAL), 100% (INHALATION)
GHS LABEL ELEMENTS:
HAZARD PICTOGRAMS: EXCLAMATION MARK
SIGNAL WORD: WARNING
HAZARD STATEMENTS:
MAY FORM COMBUSTIBLE DUST CONCENTRATIONS IN AIR.
CAUSES SERIOUS EYE IRRITATION.
PRECAUTIONARY STATEMENTS:
PREVENTION:
WEAR EYE OR FACE PROTECTION. WASH HANDS THOROUGHLY AFTER HANDLING.
RESPONSE:
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES, IF
PRESENT AND EASY TO DO. CONTINUE RINSING.
IF EYE IRRITATION PERSISTS: GET MEDICAL ATTENTION.
STORAGE: NOT APPLICABLE.
DISPOSAL: NOT APPLICABLE.
SUPPLEMENTAL LABEL ELEMENTS:
KEEP CONTAINER TIGHTLY CLOSED. KEEP AWAY FROM HEAT, SPARKS, OPEN FLAMES AND
HOT SURFACES. - NO SMOKING. PREVENT DUST ACCUMULATION. EMITS TOXIC FUMES
WHEN HEATED.
HAZARDS NOT OTHERWISE CLASSIFIED:
FINE DUST CLOUDS MAY FORM EXPLOSIVE MIXTURES WITH AIR. HANDLING AND/OR
PROCESSING OF THIS MATERIAL MAY GENERATE A DUST WHICH CAN CAUSE MECHANICAL
IRRITATION OF THE EYES, SKIN, NOSE AND THROAT.
| SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS | |
SUBSTANCE/MIXTURE: MIXTURE
PRODUCT NAME: 3535 PAINT HARDENER
INGREDIENT NAME % CAS NUMBER
| 2-PROPENOIC ACID, HOMOPOLYMER, SODIUM SALT >/=90 9003-04-7
SUB CODES REPRESENT SUBSTANCES WITHOUT REGISTERED CAS NUMBERS.
ANY CONCENTRATION SHOWN AS A RANGE IS TO PROTECT CONFIDENTIALITY OR IS DUE
TO BATCH VARIATION.
THERE ARE NO ADDITIONAL INGREDIENTS PRESENT WHICH, WITHIN THE CURRENT
KNOWLEDGE OF THE SUPPLIER AND IN THE CONCENTRATIONS APPLICABLE, ARE
CLASSIFIED AS HAZARDOUS TO HEALTH OR THE ENVIRONMENT AND HENCE REQUIRE
REPORTING IN THIS SECTION.
OCCUPATIONAL EXPOSURE LIMITS, IF AVAILABLE, ARE LISTED IN SECTION 8.
| SECTION 4. FIRST AID MEASURES | |
IF INGESTION, IRRITATION, ANY TYPE OF OVEREXPOSURE OR SYMPTOMS OF
OVEREXPOSURE OCCUR DURING OR PERSISTS AFTER USE OF THIS PRODUCT, CONTACT A
POISON CONTROL CENTER, EMERGENCY ROOM OR PHYSICIAN IMMEDIATELY; HAVE SAFETY
DATA SHEET INFORMATION AVAILABLE. NEVER GIVE ANYTHING BY MOUTH TO AN
UNCONSCIOUS OR CONVULSING PERSON.
DESCRIPTION OF NECESSARY FIRST AID MEASURES:
EYE CONTACT:
REMOVE CONTACT LENSES, IRRIGATE COPIOUSLY WITH CLEAN, FRESH WATER, HOLDING
THE EYELIDS APART FOR AT LEAST 10 MINUTES AND SEEK IMMEDIATE MEDICAL
ADVICE.
INHALATION:
REMOVE TO FRESH AIR. KEEP PERSON WARM AND AT REST. IF NOT BREATHING, IF
BREATHING IS IRREGULAR OR IF RESPIRATORY ARREST OCCURS, PROVIDE ARTIFICIAL
RESPIRATION OR OXYGEN BY TRAINED PERSONNEL.
SKIN CONTACT:
REMOVE CONTAMINATED CLOTHING AND SHOES. WASH SKIN THOROUGHLY WITH SOAP AND
WATER OR USE RECOGNIZED SKIN CLEANSER. DO NOT USE SOLVENTS OR THINNERS.
INGESTION:
IF SWALLOWED, SEEK MEDICAL ADVICE IMMEDIATELY AND SHOW THIS CONTAINER OR
LABEL. KEEP PERSON WARM AND AT REST. DO NOT INDUCE VOMITING.
MOST IMPORTANT SYMPTOMS/EFFECTS, ACUTE AND DELAYED:
POTENTIAL ACUTE HEALTH EFFECTS:
EYE CONTACT: CAUSES SERIOUS EYE IRRITATION.
INHALATION:
EXPOSURE TO AIRBORNE CONCENTRATIONS ABOVE STATUTORY OR RECOMMENDED EXPOSURE
LIMITS MAY CAUSE IRRITATION OF THE NOSE, THROAT AND LUNGS.
SKIN CONTACT: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
INGESTION: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
OVER-EXPOSURE SIGNS/SYMPTOMS:
EYE CONTACT:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
PAIN OR IRRITATION
WATERING
REDNESS
INHALATION:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
RESPIRATORY TRACT IRRITATION
COUGHING
SKIN CONTACT: NO SPECIFIC DATA.
INGESTION: NO SPECIFIC DATA.
INDICATION OF IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT NEEDED, IF
NECESSARY:
NOTES TO PHYSICIAN:
TREAT SYMPTOMATICALLY. CONTACT POISON TREATMENT SPECIALIST IMMEDIATELY IF
LARGE QUANTITIES HAVE BEEN INGESTED OR INHALED.
SPECIFIC TREATMENTS: NO SPECIFIC TREATMENT.
PROTECTION OF FIRST-AIDERS:
NO ACTION SHALL BE TAKEN INVOLVING ANY PERSONAL RISK OR WITHOUT SUITABLE
TRAINING. IT MAY BE DANGEROUS TO THE PERSON PROVIDING AID TO GIVE
MOUTH-TO-MOUTH RESUSCITATION.
SEE TOXICOLOGICAL INFORMATION (SECTION 11)
| SECTION 5. FIRE-FIGHTING MEASURES | |
EXTINGUISHING MEDIA:
SUITABLE EXTINGUISHING MEDIA: USE DRY CHEMICAL POWDER.
UNSUITABLE EXTINGUISHING MEDIA:
AVOID HIGH PRESSURE MEDIA WHICH COULD CAUSE THE FORMATION OF A POTENTIALLY
EXPLOSIBLE DUST-AIR MIXTURE.
SPECIFIC HAZARDS ARISING FROM THE CHEMICAL:
FINE DUST CLOUDS MAY FORM EXPLOSIVE MIXTURES WITH AIR.
HAZARDOUS THERMAL DECOMPOSITION PRODUCTS:
DECOMPOSITION PRODUCTS MAY INCLUDE THE FOLLOWING MATERIALS:
CARBON OXIDES
METAL OXIDE/OXIDES
SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
PROMPTLY ISOLATE THE SCENE BY REMOVING ALL PERSONS FROM THE VICINITY OF
THE INCIDENT IF THERE IS A FIRE. NO ACTION SHALL BE TAKEN INVOLVING ANY
PERSONAL RISK OR WITHOUT SUITABLE TRAINING. MOVE CONTAINERS FROM FIRE AREA
IF THIS CAN BE DONE WITHOUT RISK. USE WATER SPRAY TO KEEP FIRE-EXPOSED
CONTAINERS COOL.
SPECIAL PROTECTIVE EQUIPMENT FOR FIRE-FIGHTERS:
FIRE-FIGHTERS SHOULD WEAR APPROPRIATE PROTECTIVE EQUIPMENT AND
SELF-CONTAINED BREATHING APPARATUS (SCBA) WITH A FULL FACE-PIECE
OPERATED IN POSITIVE PRESSURE MODE.
| SECTION 6. ACCIDENTAL RELEASE MEASURES | |
PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
FOR NON-EMERGENCY PERSONNEL:
NO ACTION SHALL BE TAKEN INVOLVING ANY PERSONAL RISK OR WITHOUT SUITABLE
TRAINING. EVACUATE SURROUNDING AREAS. KEEP UNNECESSARY AND UNPROTECTED
PERSONNEL FROM ENTERING. DO NOT TOUCH OR WALK THROUGH SPILLED MATERIAL.
SHUT OFF ALL IGNITION SOURCES. NO FLARES, SMOKING OR FLAMES IN HAZARD AREA.
AVOID BREATHING DUST. PROVIDE ADEQUATE VENTILATION. WEAR APPROPRIATE
RESPIRATOR WHEN VENTILATION IS INADEQUATE. PUT ON APPROPRIATE PERSONAL
PROTECTIVE EQUIPMENT.
FOR EMERGENCY RESPONDERS:
IF SPECIALIZED CLOTHING IS REQUIRED TO DEAL WITH THE SPILLAGE, TAKE NOTE OF
ANY INFORMATION IN SECTION 8 ON SUITABLE AND UNSUITABLE MATERIALS. SEE ALSO
THE INFORMATION IN "FOR NON-EMERGENCY PERSONNEL".
ENVIRONMENTAL PRECAUTIONS:
AVOID DISPERSAL OF SPILLED MATERIAL AND RUNOFF AND CONTACT WITH SOIL,
WATERWAYS, DRAINS AND SEWERS. INFORM THE RELEVANT AUTHORITIES IF THE
PRODUCT HAS CAUSED ENVIRONMENTAL POLLUTION (SEWERS, WATERWAYS, SOIL
OR AIR).
METHODS AND MATERIALS FOR CONTAINMENT AND CLEANING UP:
SMALL SPILL:
MOVE CONTAINERS FROM SPILL AREA. USE SPARK-PROOF TOOLS AND EXPLOSION-PROOF
EQUIPMENT. AVOID DUST GENERATION. USING A VACUUM WITH HEPA FILTER WILL
REDUCE DUST DISPERSAL. PLACE SPILLED MATERIAL IN A DESIGNATED, LABELED
WASTE CONTAINER. DISPOSE OF VIA A LICENSED WASTE DISPOSAL CONTRACTOR.
LARGE SPILL:
MOVE CONTAINERS FROM SPILL AREA. USE SPARK-PROOF TOOLS AND EXPLOSION-PROOF
EQUIPMENT. APPROACH RELEASE FROM UPWIND. PREVENT ENTRY INTO SEWERS, WATER
COURSES, BASEMENTS OR CONFINED AREAS. AVOID DUST GENERATION. DO NOT DRY
SWEEP. VACUUM DUST WITH EQUIPMENT FITTED WITH A HEPA FILTER AND PLACE IN
A CLOSED, LABELED WASTE CONTAINER. AVOID CREATING DUSTY CONDITIONS AND
PREVENT WIND DISPERSAL. DISPOSE OF VIA A LICENSED WASTE DISPOSAL
CONTRACTOR.
NOTE:
SEE SECTION 1 FOR EMERGENCY CONTACT INFORMATION AND SECTION 13 FOR WASTE
DISPOSAL.
| SECTION 7. HANDLING AND STORAGE | |
PRECAUTIONS FOR SAFE HANDLING:
PROTECTIVE MEASURES:
PUT ON APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT (SEE SECTION 8). DO NOT
INGEST. AVOID CONTACT WITH EYES, SKIN AND CLOTHING. AVOID BREATHING DUST.
AVOID THE CREATION OF DUST WHEN HANDLING AND AVOID ALL POSSIBLE SOURCES OF
IGNITION (SPARK OR FLAME). PREVENT DUST ACCUMULATION. USE ONLY WITH
ADEQUATE VENTILATION. WEAR APPROPRIATE RESPIRATOR WHEN VENTILATION IS
INADEQUATE. KEEP IN THE ORIGINAL CONTAINER OR AN APPROVED ALTERNATIVE MADE
FROM A COMPATIBLE MATERIAL, KEPT TIGHTLY CLOSED WHEN NOT IN USE. ELECTRICAL
EQUIPMENT AND LIGHTING SHOULD BE PROTECTED TO APPROPRIATE STANDARDS TO
PREVENT DUST COMING INTO CONTACT WITH HOT SURFACES, SPARKS OR OTHER
IGNITION SOURCES. TAKE PRECAUTIONARY MEASURES AGAINST ELECTROSTATIC
DISCHARGES. TO AVOID FIRE OR EXPLOSION, DISSIPATE STATIC ELECTRICITY
DURING TRANSFER BY GROUNDING AND BONDING CONTAINERS AND EQUIPMENT BEFORE
TRANSFERRING MATERIAL. EMPTY CONTAINERS RETAIN PRODUCT RESIDUE AND CAN BE
HAZARDOUS. DO NOT REUSE CONTAINER.
ADVICE ON GENERAL OCCUPATIONAL HYGIENE:
EATING, DRINKING AND SMOKING SHOULD BE PROHIBITED IN AREAS WHERE THIS
MATERIAL IS HANDLED, STORED AND PROCESSED. WORKERS SHOULD WASH HANDS AND
FACE BEFORE EATING, DRINKING AND SMOKING. REMOVE CONTAMINATED CLOTHING AND
PROTECTIVE EQUIPMENT BEFORE ENTERING EATING AREAS. SEE ALSO SECTION 8 FOR
ADDITIONAL INFORMATION ON HYGIENE MEASURES.
CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPATIBILITIES:
DO NOT STORE BELOW THE FOLLOWING TEMPERATURE:
5 DEG. C (41 DEG. F). STORE IN ACCORDANCE WITH LOCAL REGULATIONS. STORE IN
A SEGREGATED AND APPROVED AREA. STORE IN ORIGINAL CONTAINER PROTECTED FROM
DIRECT SUNLIGHT IN A DRY, COOL AND WELL-VENTILATED AREA, AWAY FROM
INCOMPATIBLE MATERIALS (SEE SECTION 10) AND FOOD AND DRINK. ELIMINATE ALL
IGNITION SOURCES. SEPARATE FROM OXIDIZING MATERIALS. KEEP CONTAINER TIGHTLY
CLOSED AND SEALED UNTIL READY FOR USE. CONTAINERS THAT HAVE BEEN OPENED
MUST BE CAREFULLY RESEALED AND KEPT UPRIGHT TO PREVENT LEAKAGE. DO NOT
STORE IN UNLABELED CONTAINERS. USE APPROPRIATE CONTAINMENT TO AVOID
ENVIRONMENTAL CONTAMINATION.
| SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION | |
CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
INGREDIENT NAME EXPOSURE LIMITS
| 2-PROPENOIC ACID, HOMOPOLYMER, SODIUM SALT NONE.
KEY TO ABBREVIATIONS:
A = ACCEPTABLE MAXIMUM PEAK
ACGIH = AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS.
C = CEILING LIMIT
F = FUME
IPEL = INTERNAL PERMISSIBLE EXPOSURE LIMIT
OSHA = OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION.
R = RESPIRABLE
S = POTENTIAL SKIN ABSORPTION
SR = RESPIRATORY SENSITIZATION
SS = SKIN SENSITIZATION
STEL = SHORT TERM EXPOSURE LIMIT VALUES
TD = TOTAL DUST
TLV = THRESHOLD LIMIT VALUE
TWA = TIME WEIGHTED AVERAGE
Z = OSHA 29 CFR 1910.1200 SUBPART Z - TOXIC AND HAZARDOUS SUBSTANCES
CONSULT LOCAL AUTHORITIES FOR ACCEPTABLE EXPOSURE LIMITS.
RECOMMENDED MONITORING PROCEDURES:
IF THIS PRODUCT CONTAINS INGREDIENTS WITH EXPOSURE LIMITS, PERSONAL,
WORKPLACE ATMOSPHERE OR BIOLOGICAL MONITORING MAY BE REQUIRED TO DETERMINE
THE EFFECTIVENESS OF THE VENTILATION OR OTHER CONTROL MEASURES AND/OR THE
NECESSITY TO USE RESPIRATORY PROTECTIVE EQUIPMENT. REFERENCE SHOULD BE
MADE TO APPROPRIATE MONITORING STANDARDS. REFERENCE TO NATIONAL GUIDANCE
DOCUMENTS FOR METHODS FOR THE DETERMINATION OF HAZARDOUS SUBSTANCES WILL
ALSO BE REQUIRED.
APPROPRIATE ENGINEERING CONTROLS:
USE ONLY WITH ADEQUATE VENTILATION. IF USER OPERATIONS GENERATE DUST,
FUMES, GAS, VAPOR OR MIST, USE PROCESS ENCLOSURES, LOCAL EXHAUST
VENTILATION OR OTHER ENGINEERING CONTROLS TO KEEP WORKER EXPOSURE TO
AIRBORNE CONTAMINANTS BELOW ANY RECOMMENDED OR STATUTORY LIMITS. THE
ENGINEERING CONTROLS ALSO NEED TO KEEP GAS, VAPOR OR DUST CONCENTRATIONS
BELOW ANY LOWER EXPLOSIVE LIMITS. USE EXPLOSION-PROOF VENTILATION
EQUIPMENT.
ENVIRONMENTAL EXPOSURE CONTROLS:
EMISSIONS FROM VENTILATION OR WORK PROCESS EQUIPMENT SHOULD BE CHECKED
TO ENSURE THEY COMPLY WITH THE REQUIREMENTS OF ENVIRONMENTAL PROTECTION
LEGISLATION. IN SOME CASES, FUME SCRUBBERS, FILTERS OR ENGINEERING
MODIFICATIONS TO THE PROCESS EQUIPMENT WILL BE NECESSARY TO REDUCE
EMISSIONS TO ACCEPTABLE LEVELS.
INDIVIDUAL PROTECTION MEASURES:
HYGIENE MEASURES:
WASH HANDS, FOREARMS AND FACE THOROUGHLY AFTER HANDLING CHEMICAL PRODUCTS,
BEFORE EATING, SMOKING AND USING THE LAVATORY AND AT THE END OF THE WORKING
PERIOD. APPROPRIATE TECHNIQUES SHOULD BE USED TO REMOVE POTENTIALLY
CONTAMINATED CLOTHING. WASH CONTAMINATED CLOTHING BEFORE REUSING. ENSURE
THAT EYEWASH STATIONS AND SAFETY SHOWERS ARE CLOSE TO THE WORKSTATION
LOCATION.
EYE/FACE PROTECTION: CHEMICAL SPLASH GOGGLES.
SKIN PROTECTION:
HAND PROTECTION:
CHEMICAL-RESISTANT, IMPERVIOUS GLOVES COMPLYING WITH AN APPROVED STANDARD
SHOULD BE WORN AT ALL TIMES WHEN HANDLING CHEMICAL PRODUCTS IF A RISK
ASSESSMENT INDICATES THIS IS NECESSARY. CONSIDERING THE PARAMETERS
SPECIFIED BY THE GLOVE MANUFACTURER, CHECK DURING USE THAT THE GLOVES ARE
STILL RETAINING THEIR PROTECTIVE PROPERTIES. IT SHOULD BE NOTED THAT THE
TIME TO BREAKTHROUGH FOR ANY GLOVE MATERIAL MAY BE DIFFERENT FOR DIFFERENT
GLOVE MANUFACTURERS. IN THE CASE OF MIXTURES, CONSISTING OF SEVERAL
SUBSTANCES, THE PROTECTION TIME OF THE GLOVES CANNOT BE ACCURATELY
ESTIMATED.
BODY PROTECTION:
PERSONAL PROTECTIVE EQUIPMENT FOR THE BODY SHOULD BE SELECTED BASED ON THE
TASK BEING PERFORMED AND THE RISKS INVOLVED AND SHOULD BE APPROVED BY A
SPECIALIST BEFORE HANDLING THIS PRODUCT.
OTHER SKIN PROTECTION:
APPROPRIATE FOOTWEAR AND ANY ADDITIONAL SKIN PROTECTION MEASURES SHOULD BE
SELECTED BASED ON THE TASK BEING PERFORMED AND THE RISKS INVOLVED AND
SHOULD BE APPROVED BY A SPECIALIST BEFORE HANDLING THIS PRODUCT.
RESPIRATORY PROTECTION:
RESPIRATOR SELECTION MUST BE BASED ON KNOWN OR ANTICIPATED EXPOSURE LEVELS,
THE HAZARDS OF THE PRODUCT AND THE SAFE WORKING LIMITS OF THE SELECTED
RESPIRATOR. IF WORKERS ARE EXPOSED TO CONCENTRATIONS ABOVE THE EXPOSURE
LIMIT, THEY MUST USE APPROPRIATE, CERTIFIED RESPIRATORS. USE A PROPERLY
FITTED, AIR-PURIFYING OR AIR-FED RESPIRATOR COMPLYING WITH AN APPROVED
STANDARD IF A RISK ASSESSMENT INDICATES THIS IS NECESSARY.
| SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES | |
APPEARANCE:
PHYSICAL STATE: SOLID.
COLOR: NOT AVAILABLE.
ODOR: CHARACTERISTIC.
ODOR THRESHOLD: NOT AVAILABLE.
PH: NOT AVAILABLE.
MELTING POINT: NOT AVAILABLE.
BOILING POINT: NOT AVAILABLE.
FLASH POINT:
CLOSED CUP: NOT APPLICABLE. [PRODUCT DOES NOT SUSTAIN COMBUSTION.]
AUTO-IGNITION TEMPERATURE: NOT AVAILABLE.
DECOMPOSITION TEMPERATURE: NOT AVAILABLE.
FLAMMABILITY (SOLID, GAS): NOT AVAILABLE.
LOWER AND UPPER EXPLOSIVE (FLAMMABLE) LIMITS: NOT AVAILABLE.
EVAPORATION RATE: NOT AVAILABLE.
VAPOR PRESSURE: NOT AVAILABLE.
VAPOR DENSITY: NOT AVAILABLE.
RELATIVE DENSITY: 1.3
DENSITY (LBS/GAL): 10.85
SOLUBILITY:
INSOLUBLE IN THE FOLLOWING MATERIALS: COLD WATER.
PARTITION COEFFICIENT N-OCTANOL/WATER: NOT AVAILABLE.
VISCOSITY:
KINEMATIC (40 DEG. C (104 DEG. F)): NOT APPLICABLE.
VOLATILITY:
0% (V/V)
0% (W/W)
% SOLID. (W/W): 100
| SECTION 10. STABILITY AND REACTIVITY | |
REACTIVITY:
NO SPECIFIC TEST DATA RELATED TO REACTIVITY AVAILABLE FOR THIS PRODUCT OR
ITS INGREDIENTS.
CHEMICAL STABILITY: THE PRODUCT IS STABLE.
POSSIBILITY OF HAZARDOUS REACTIONS:
UNDER NORMAL CONDITIONS OF STORAGE AND USE, HAZARDOUS REACTIONS WILL NOT
OCCUR.
CONDITIONS TO AVOID:
WHEN EXPOSED TO HIGH TEMPERATURES MAY PRODUCE HAZARDOUS DECOMPOSITION
PRODUCTS. REFER TO PROTECTIVE MEASURES LISTED IN SECTIONS 7 AND 8.
INCOMPATIBLE MATERIALS:
KEEP AWAY FROM THE FOLLOWING MATERIALS TO PREVENT STRONG EXOTHERMIC
REACTIONS: OXIDIZING AGENTS, STRONG ALKALIS, STRONG ACIDS.
HAZARDOUS DECOMPOSITION PRODUCTS:
DECOMPOSITION PRODUCTS MAY INCLUDE THE FOLLOWING MATERIALS:
CARBON MONOXIDE, CARBON DIOXIDE, SMOKE, OXIDES OF NITROGEN.
| SECTION 11. TOXICOLOGICAL INFORMATION | |
INFORMATION ON TOXICOLOGICAL EFFECTS:
ACUTE TOXICITY:
PRODUCT/INGREDIENT NAME RESULT SPECIES DOSE EXPOSURE
| 2-PROPENOIC ACID, LD50 ORAL RAT >8250 MG/KG
| HOMOPOLYMER, SODIUM SALT
CONCLUSION/SUMMARY: THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF.
IRRITATION/CORROSION:
CONCLUSION/SUMMARY:
SKIN: THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF.
EYES: THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF.
RESPIRATORY: THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF.
SENSITIZATION:
CONCLUSION/SUMMARY:
SKIN: THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF.
RESPIRATORY: THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF.
MUTAGENICITY:
CONCLUSION/SUMMARY: THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF.
CARCINOGENICITY:
CONCLUSION/SUMMARY: THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF.
REPRODUCTIVE TOXICITY:
CONCLUSION/SUMMARY: THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF.
TERATOGENICITY:
CONCLUSION/SUMMARY: THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF.
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE): NOT AVAILABLE.
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE): NOT AVAILABLE.
ASPIRATION HAZARD: NOT AVAILABLE.
INFORMATION ON THE LIKELY ROUTES OF EXPOSURE:
POTENTIAL ACUTE HEALTH EFFECTS:
EYE CONTACT: CAUSES SERIOUS EYE IRRITATION.
INHALATION:
EXPOSURE TO AIRBORNE CONCENTRATIONS ABOVE STATUTORY OR RECOMMENDED EXPOSURE
LIMITS MAY CAUSE IRRITATION OF THE NOSE, THROAT AND LUNGS.
SKIN CONTACT: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
INGESTION: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
OVER-EXPOSURE SIGNS/SYMPTOMS:
EYE CONTACT:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
PAIN OR IRRITATION
WATERING
REDNESS
INHALATION:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
RESPIRATORY TRACT IRRITATION
COUGHING
SKIN CONTACT: NO SPECIFIC DATA.
INGESTION: NO SPECIFIC DATA.
DELAYED AND IMMEDIATE EFFECTS AND ALSO CHRONIC EFFECTS FROM SHORT AND LONG
TERM EXPOSURE:
CONCLUSION/SUMMARY:
THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF. REPEATED EXPOSURE OF
THE EYES TO A LOW LEVEL OF DUST CAN PRODUCE EYE IRRITATION. REPEATED OR
PROLONGED INHALATION OF DUST MAY LEAD TO CHRONIC RESPIRATORY IRRITATION.
INGESTION MAY CAUSE NAUSEA, DIARRHEA AND VOMITING. THIS TAKES INTO ACCOUNT,
WHERE KNOWN, DELAYED AND IMMEDIATE EFFECTS AND ALSO CHRONIC EFFECTS OF
COMPONENTS FROM SHORT-TERM AND LONG-TERM EXPOSURE BY ORAL, INHALATION AND
DERMAL ROUTES OF EXPOSURE AND EYE CONTACT.
SHORT TERM EXPOSURE:
POTENTIAL IMMEDIATE EFFECTS:
THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF.
POTENTIAL DELAYED EFFECTS:
THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF.
LONG TERM EXPOSURE:
POTENTIAL IMMEDIATE EFFECTS:
THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF.
POTENTIAL DELAYED EFFECTS:
THERE ARE NO DATA AVAILABLE ON THE MIXTURE ITSELF.
POTENTIAL CHRONIC HEALTH EFFECTS:
GENERAL:
REPEATED OR PROLONGED INHALATION OF DUST MAY LEAD TO CHRONIC RESPIRATORY
IRRITATION.
CARCINOGENICITY: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
MUTAGENICITY: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
TERATOGENICITY: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
DEVELOPMENTAL EFFECTS: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
FERTILITY EFFECTS: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
| SECTION 12. ECOLOGICAL INFORMATION | |
TOXICITY: NOT AVAILABLE.
PERSISTENCE AND DEGRADABILITY: NOT AVAILABLE.
BIOACCUMULATIVE POTENTIAL: NOT AVAILABLE.
MOBILITY IN SOIL:
SOIL/WATER PARTITION COEFFICIENT (KOC): NOT AVAILABLE.
| SECTION 13. DISPOSAL CONSIDERATIONS | |
DISPOSAL METHODS:
THE GENERATION OF WASTE SHOULD BE AVOIDED OR MINIMIZED WHEREVER POSSIBLE.
DISPOSAL OF THIS PRODUCT, SOLUTIONS AND ANY BY-PRODUCTS SHOULD AT ALL TIMES
COMPLY WITH THE REQUIREMENTS OF ENVIRONMENTAL PROTECTION AND WASTE DISPOSAL
LEGISLATION AND ANY REGIONAL LOCAL AUTHORITY REQUIREMENTS. DISPOSE OF
SURPLUS AND NON-RECYCLABLE PRODUCTS VIA A LICENSED WASTE DISPOSAL
CONTRACTOR. WASTE SHOULD NOT BE DISPOSED OF UNTREATED TO THE SEWER UNLESS
FULLY COMPLIANT WITH THE REQUIREMENTS OF ALL AUTHORITIES WITH JURISDICTION.
WASTE PACKAGING SHOULD BE RECYCLED. INCINERATION OR LANDFILL SHOULD ONLY BE
CONSIDERED WHEN RECYCLING IS NOT FEASIBLE. THIS MATERIAL AND ITS CONTAINER
MUST BE DISPOSED OF IN A SAFE WAY. CARE SHOULD BE TAKEN WHEN HANDLING
EMPTIED CONTAINERS THAT HAVE NOT BEEN CLEANED OR RINSED OUT. EMPTY
CONTAINERS OR LINERS MAY RETAIN SOME PRODUCT RESIDUES. AVOID DISPERSAL OF
SPILLED MATERIAL AND RUNOFF AND CONTACT WITH SOIL, WATERWAYS, DRAINS AND
SEWERS.
DISPOSAL SHOULD BE IN ACCORDANCE WITH APPLICABLE REGIONAL, NATIONAL AND
LOCAL LAWS AND REGULATIONS.
REFER TO SECTION 7: HANDLING AND STORAGE AND SECTION 8: EXPOSURE
CONTROLS/PERSONAL PROTECTION FOR ADDITIONAL HANDLING INFORMATION AND
PROTECTION OF EMPLOYEES. SECTION 6. ACCIDENTAL RELEASE MEASURES
| SECTION 14. TRANSPORT INFORMATION | |
DOT IMDG IATA
UN NUMBER NOT REGULATED. NOT REGULATED. NOT REGULATED.
UN PROPER SHIPPING
NAME
TRANSPORT HAZARD
CLASS(ES)
PACKING GROUP
ENVIRONMENTAL NO. NO. NO.
HAZARDS
MARINE POLLUTANT NOT APPLICABLE. NOT APPLICABLE. NOT APPLICABLE.
SUBSTANCES
ADDITIONAL INFORMATION:
DOT: NONE IDENTIFIED.
IMDG: NONE IDENTIFIED.
IATA: NONE IDENTIFIED.
SPECIAL PRECAUTIONS FOR USER:
TRANSPORT WITHIN USER'S PREMISES:
ALWAYS TRANSPORT IN CLOSED CONTAINERS THAT ARE UPRIGHT AND SECURE. ENSURE
THAT PERSONS TRANSPORTING THE PRODUCT KNOW WHAT TO DO IN THE EVENT OF AN
ACCIDENT OR SPILLAGE.
| SECTION 15. REGULATORY INFORMATION | |
UNITED STATES:
UNITED STATES INVENTORY (TSCA 8B): ALL COMPONENTS ARE LISTED OR EXEMPTED.
SARA 302/304:
SARA 304 RQ: NOT APPLICABLE.
COMPOSITION/INFORMATION ON INGREDIENTS: NO PRODUCTS WERE FOUND.
SARA 311/312:
CLASSIFICATION:
COMBUSTIBLE DUSTS
EYE IRRITATION: CATEGORY 2A
COMPOSITION/INFORMATION ON INGREDIENTS:
NAME % CLASSIFICATION
| 2-PROPENOIC ACID, HOMOPOLYMER, >90 EYE IRRITATION: CATEGORY 2A
| SODIUM SALT
ADDITIONAL ENVIRONMENTAL INFORMATION IS CONTAINED ON THE ENVIRONMENTAL DATA
SHEET FOR THIS PRODUCT, WHICH CAN BE OBTAINED FROM YOUR PPG REPRESENTATIVE.
| SECTION 16. OTHER INFORMATION | |
HAZARDOUS MATERIAL INFORMATION SYSTEM (U.S.A.):
HEALTH 2
FLAMMABILITY 0
PHYSICAL HAZARDS 0
(*) - CHRONIC EFFECTS
CAUTION:
HMIS(R*) RATINGS ARE BASED ON A 0-4 RATING SCALE, WITH 0 REPRESENTING
MINIMAL HAZARDS OR RISKS, AND 4 REPRESENTING SIGNIFICANT HAZARDS OR RISKS.
ALTHOUGH HMIS(R*) RATINGS AND THE ASSOCIATED LABEL ARE NOT REQUIRED ON
MSDSS OR PRODUCTS LEAVING A FACILITY UNDER 29 CFR 1910.1200, THE PREPARER
MAY CHOOSE TO PROVIDE THEM. HMIS(R*) RATINGS ARE TO BE USED WITH A FULLY
IMPLEMENTED HMIS(R*) PROGRAM. HMIS(R*) IS A REGISTERED TRADEMARK AND
SERVICE MARK OF THE AMERICAN COATINGS ASSOCIATION, INC.
THE CUSTOMER IS RESPONSIBLE FOR DETERMINING THE PPE CODE FOR THIS MATERIAL.
FOR MORE INFORMATION ON HMIS(R*) PERSONAL PROTECTIVE EQUIPMENT (PPE) CODES,
CONSULT THE HMIS(R*) IMPLEMENTATION MANUAL.
NATIONAL FIRE PROTECTION ASSOCIATION (U.S.A.):
HEALTH 2
FLAMMABILITY 0
INSTABILITY 0
DATE OF PREVIOUS ISSUE: 5/15/2018
ORGANIZATION THAT PREPARED THE MSDS: EHS
KEY TO ABBREVIATIONS:
ATE: ACUTE TOXICITY ESTIMATE
BCF: BIOCONCENTRATION FACTOR
GHS:
GLOBALLY HARMONIZED SYSTEM OF CLASSIFICATION AND LABELLING OF CHEMICALS
IATA: INTERNATIONAL AIR TRANSPORT ASSOCIATION
IBC: INTERMEDIATE BULK CONTAINER
IMDG: INTERNATIONAL MARITIME DANGEROUS GOODS
LOGPOW: LOGARITHM OF THE OCTANOL/WATER PARTITION COEFFICIENT
MARPOL:
INTERNATIONAL CONVENTION FOR THE PREVENTION OF POLLUTION FROM SHIPS,
1973 AS MODIFIED BY THE PROTOCOL OF 1978. ("MARPOL" = MARINE POLLUTION)
N/A: NOT AVAILABLE
SGG: SEGREGATION GROUP
UN: UNITED NATIONS
| INDICATES INFORMATION THAT HAS CHANGED FROM PREVIOUSLY ISSUED VERSION.
DISCLAIMER:
THE INFORMATION CONTAINED IN THIS DATA SHEET IS BASED ON PRESENT SCIENTIFIC
AND TECHNICAL KNOWLEDGE. THE PURPOSE OF THIS INFORMATION IS TO DRAW
ATTENTION TO THE HEALTH AND SAFETY ASPECTS CONCERNING THE PRODUCTS SUPPLIED
BY PPG, AND TO RECOMMEND PRECAUTIONARY MEASURES FOR THE STORAGE AND
HANDLING OF THE PRODUCTS. NO WARRANTY OR GUARANTEE IS GIVEN IN RESPECT OF
THE PROPERTIES OF THE PRODUCTS. NO LIABILITY CAN BE ACCEPTED FOR ANY
FAILURE TO OBSERVE THE PRECAUTIONARY MEASURES DESCRIBED IN THIS DATA SHEET
OR FOR ANY MISUSE OF THE PRODUCTS.
UNITED STATES