| Common Name: | SILICONE LUBRICANT |
| Manufacturer: | 3M |
| SDS Revision Date: | 5/21/2018 |
| SDS Format: | No Format Specified |
| Item Number(s): | 2GKG9, 51DU97, 56XN21, 56XN22, 817PR8 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M(TM) SILICONE LUBRICANT
05/21/18
3M
SAFETY DATA SHEET
COPYRIGHT,2018,3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR
THE PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR
WRITTEN AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 05-6937-6
ISSUE DATE: 05/21/18
VERSION NUMBER: 25.00
SUPERCEDES DATE: 01/18/18
| SECTION 1: IDENTIFICATION |  |
1.1. PRODUCT IDENTIFIER: 3M(TM) SILICONE LUBRICANT
PRODUCT IDENTIFICATION NUMBERS:
62-4678-0930-7, 62-4678-0931-5, 62-4678-4930-3, 62-4678-4935-2,
78-8033-2219-3
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE: INDUSTRIAL USE
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: INDUSTRIAL ADHESIVES AND TAPES DIVISION
ADDRESS:
3M CENTER, ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
FLAMMABLE AEROSOL: CATEGORY 1.
GAS UNDER PRESSURE: LIQUEFIED GAS.
SERIOUS EYE DAMAGE/IRRITATION: CATEGORY 2B.
SIMPLE ASPHYXIANT.
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE): CATEGORY 1.
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE): CATEGORY 3.
2.2. LABEL ELEMENTS:
SIGNAL WORD: DANGER
SYMBOLS:
FLAME
GAS CYLINDER
EXCLAMATION MARK
HEALTH HAZARD
PICTOGRAMS:
FLAME
GAS CYLINDER
EXCLAMATION MARK
HEALTH HAZARD
HAZARD STATEMENTS:
EXTREMELY FLAMMABLE AEROSOL.
CONTAINS GAS UNDER PRESSURE; MAY EXPLODE IF HEATED.
CAUSES EYE IRRITATION.
MAY CAUSE DROWSINESS OR DIZZINESS.
MAY DISPLACE OXYGEN AND CAUSE RAPID SUFFOCATION.
CAUSES DAMAGE TO ORGANS: CARDIOVASCULAR SYSTEM
PRECAUTIONARY STATEMENTS:
GENERAL: KEEP OUT OF REACH OF CHILDREN.
PREVENTION:
KEEP AWAY FROM HEAT/SPARKS/OPEN FLAMES/HOT SURFACES. - NO SMOKING.
DO NOT SPRAY ON AN OPEN FLAME OR OTHER IGNITION SOURCE.
PRESSURIZED CONTAINER: DO NOT PIERCE OR BURN, EVEN AFTER USE.
DO NOT BREATHE DUST/FUME/GAS/MIST/VAPORS/SPRAY.
USE ONLY OUTDOORS OR IN A WELL-VENTILATED AREA.
DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT.
WASH THOROUGHLY AFTER HANDLING.
RESPONSE:
IF INHALED: REMOVE PERSON TO FRESH AIR AND KEEP COMFORTABLE FOR BREATHING.
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES, IF
PRESENT AND EASY TO DO. CONTINUE RINSING.
IF EYE IRRITATION PERSISTS: GET MEDICAL ADVICE/ATTENTION.
IF EXPOSED: CALL A POISON CENTER OR DOCTOR/PHYSICIAN.
SPECIFIC TREATMENT (SEE NOTES TO PHYSICIAN ON THIS LABEL).
STORAGE:
PROTECT FROM SUNLIGHT. DO NOT EXPOSE TO TEMPERATURES EXCEEDING 50C/122F.
KEEP CONTAINER TIGHTLY CLOSED.
STORE LOCKED UP IN A WELL-VENTILATED PLACE.
DISPOSAL:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH APPLICABLE LOCAL/REGIONAL
/NATIONAL/INTERNATIONAL REGULATIONS.
NOTES TO PHYSICIAN:
EXPOSURE MAY INCREASE MYOCARDIAL IRRITABILITY. DO NOT ADMINISTER
SYMPATHOMIMETIC DRUGS UNLESS ABSOLUTELY NECESSARY.
SUPPLEMENTAL INFORMATION: MAY CAUSE FROSTBITE.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
ISOBUTANE 75-28-5 70 - 80 TRADE SECRET *
HEPTANE 142-82-5 15 - 25 TRADE SECRET *
POLY(DIMETHYLSILOXANE) 63148-62-9 3 - 7 TRADE SECRET *
*THE SPECIFIC CHEMICAL IDENTITY AND/OR EXACT PERCENTAGE (CONCENTRATION) OF
THIS COMPOSITION HAS BEEN WITHHELD AS A TRADE SECRET.
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION: REMOVE PERSON TO FRESH AIR. GET MEDICAL ATTENTION.
SKIN CONTACT:
THAW FROSTED SKIN WITH LUKEWARM WATER. DO NOT RUB AFFECTED AREA. GET
MEDICAL ATTENTION.
EYE CONTACT:
IMMEDIATELY FLUSH WITH LARGE AMOUNTS OF WATER. REMOVE CONTACT LENSES IF
EASY TO DO. CONTINUE RINSING. GET MEDICAL ATTENTION.
IF SWALLOWED: RINSE MOUTH. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED:
EXPOSURE MAY INCREASE MYOCARDIAL IRRITABILITY. DO NOT ADMINISTER
SYMPATHOMIMETIC DRUGS UNLESS ABSOLUTELY NECESSARY.
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
USE A FIRE FIGHTING AGENT SUITABLE FOR THE SURROUNDING FIRE.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
CLOSED CONTAINERS EXPOSED TO HEAT FROM FIRE MAY BUILD PRESSURE AND
EXPLODE.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
WATER MAY NOT EFFECTIVELY EXTINGUISH FIRE; HOWEVER, IT SHOULD BE USED TO
KEEP FIRE-EXPOSED CONTAINERS AND SURFACES COOL AND PREVENT EXPLOSIVE
RUPTURE.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
EVACUATE AREA. KEEP AWAY FROM HEAT/SPARKS/OPEN FLAMES/HOT SURFACES. - NO
SMOKING. USE ONLY NON-SPARKING TOOLS.
VENTILATE THE AREA WITH FRESH AIR. FOR LARGE SPILL, OR SPILLS IN CONFINED
SPACES, PROVIDE MECHANICAL VENTILATION TO DISPERSE OR EXHAUST VAPORS, IN
ACCORDANCE WITH GOOD INDUSTRIAL HYGIENE PRACTICE. WARNING! A MOTOR COULD
BE AN IGNITION SOURCE AND COULD CAUSE FLAMMABLE GASES OR VAPORS IN THE
SPILL AREA TO BURN OR EXPLODE. REFER TO OTHER SECTIONS OF THIS SDS FOR
INFORMATION REGARDING PHYSICAL AND HEALTH HAZARDS, RESPIRATORY PROTECTION,
VENTILATION, AND PERSONAL PROTECTIVE EQUIPMENT.
6.2. ENVIRONMENTAL PRECAUTIONS: AVOID RELEASE TO THE ENVIRONMENT.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP:
IF POSSIBLE, SEAL LEAKING CONTAINER. PLACE LEAKING CONTAINERS IN A WELL-
VENTILATED AREA, PREFERABLY AN OPERATING EXHAUST HOOD, OR IF NECESSARY
OUTDOORS ON AN IMPERMEABLE SURFACE UNTIL APPROPRIATE PACKAGING FOR THE
LEAKING CONTAINER OR ITS CONTENTS IS AVAILABLE. COLLECT AS MUCH OF THE
SPILLED MATERIAL AS POSSIBLE USING NON-SPARKING TOOLS. PLACE IN A METAL
CONTAINER APPROVED FOR TRANSPORTATION BY APPROPRIATE AUTHORITIES. SEAL
THE CONTAINER. DISPOSE OF COLLECTED MATERIAL AS SOON AS POSSIBLE IN
ACCORDANCE WITH APPLICABLE LOCAL/REGIONAL/NATIONAL/INTERNATIONAL
REGULATIONS.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
KEEP OUT OF REACH OF CHILDREN. KEEP AWAY FROM HEAT/SPARKS/OPEN FLAMES/HOT
SURFACES. - NO SMOKING. DO NOT SPRAY ON AN OPEN FLAME OR OTHER IGNITION
SOURCE. DO NOT PIERCE OR BURN, EVEN AFTER USE. DO NOT BREATHE DUST/FUME/
GAS/MIST/VAPORS/SPRAY. DO NOT GET IN EYES, ON SKIN, OR ON CLOTHING. DO NOT
EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT. WASH THOROUGHLY AFTER
HANDLING. AVOID CONTACT WITH OXIDIZING AGENTS (EG. CHLORINE, CHROMIC ACID
ETC.)
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
STORE IN A WELL-VENTILATED PLACE. KEEP CONTAINER TIGHTLY CLOSED. PROTECT
FROM SUNLIGHT. DO NOT EXPOSE TO TEMPERATURES EXCEEDING 50C/122F. STORE
AWAY FROM HEAT. STORE AWAY FROM ACIDS. STORE AWAY FROM OXIDIZING AGENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN THE TABLE
BELOW, AN OCCUPATIONAL EXPOSURE LIMIT IS NOT AVAILABLE FOR THE COMPONENT.
INGREDIENT C.A.S. AGENCY LIMIT ADDITIONAL
NO. TYPE COMMENTS
HEPTANE 142-82-5 ACGIH TWA: 400 PPM;
STEL: 500 PPM
HEPTANE 142-82-5 OSHA TWA:
2000 MG/M3
(500 PPM)
ISOBUTANE 75-28-5 ACGIH STEL: 1000 PPM
NATURAL GAS 75-28-5 ACGIH LIMIT VALUE NOT SIMPLE
ESTABLISHED: ASPHYXIANT
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
AIHA: AMERICAN INDUSTRIAL HYGIENE ASSOCIATION
CMRG: CHEMICAL MANUFACTURER'S RECOMMENDED GUIDELINES
OSHA:
UNITED STATES DEPARTMENT OF LABOR - OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION
TWA: TIME-WEIGHTED-AVERAGE
STEL: SHORT TERM EXPOSURE LIMIT
CEIL: CEILING
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
DO NOT REMAIN IN AREA WHERE AVAILABLE OXYGEN MAY BE REDUCED. USE GENERAL
DILUTION VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO CONTROL AIRBORNE
EXPOSURES TO BELOW RELEVANT EXPOSURE LIMITS AND/OR CONTROL DUST/FUME/GAS/
MIST/VAPORS/SPRAY. IF VENTILATION IS NOT ADEQUATE, USE RESPIRATORY
PROTECTION EQUIPMENT.
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON THE RESULTS
OF AN EXPOSURE ASSESSMENT. THE FOLLOWING EYE/FACE PROTECTION(S) ARE
RECOMMENDED:
INDIRECT VENTED GOGGLES
SKIN/HAND PROTECTION:
SELECT AND USE GLOVES AND/OR PROTECTIVE CLOTHING APPROVED TO RELEVANT
LOCAL STANDARDS TO PREVENT SKIN CONTACT BASED ON THE RESULTS OF AN
EXPOSURE ASSESSMENT. SELECTION SHOULD BE BASED ON USE FACTORS SUCH AS
EXPOSURE LEVELS, CONCENTRATION OF THE SUBSTANCE OR MIXTURE, FREQUENCY
AND DURATION, PHYSICAL CHALLENGES SUCH AS TEMPERATURE EXTREMES, AND
OTHER USE CONDITIONS. CONSULT WITH YOUR GLOVE AND/OR PROTECTIVE CLOTHING
MANUFACTURER FOR SELECTION OF APPROPRIATE COMPATIBLE GLOVES/PROTECTIVE
CLOTHING.
GLOVES MADE FROM THE FOLLOWING MATERIAL(S) ARE RECOMMENDED: NITRILE RUBBER
RESPIRATORY PROTECTION:
AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF A RESPIRATOR IS
REQUIRED. IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS PART OF A FULL
RESPIRATORY PROTECTION PROGRAM. BASED ON THE RESULTS OF THE EXPOSURE
ASSESSMENT, SELECT FROM THE FOLLOWING RESPIRATOR TYPE(S) TO REDUCE
INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE SUPPLIED-AIR RESPIRATOR
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
THERMAL HAZARDS: WEAR COLD INSULATING GLOVES/FACE SHIELD/EYE PROTECTION.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: LIQUID
ODOR, COLOR, GRADE: IN AEROSOL, TRANSPARENT, VERY SLIGHT ODOR
ODOR THRESHOLD: NO DATA AVAILABLE
PH: NOT APPLICABLE
MELTING POINT: NO DATA AVAILABLE
BOILING POINT: NO DATA AVAILABLE
FLASH POINT:
-50 DEG. F [TEST METHOD:TAGLIABUE CLOSED CUP]
[DETAILS:CONDITIONS: PROPELLANT]
EVAPORATION RATE: 1.9 [REF STD:WATER=1]
FLAMMABILITY (SOLID, GAS): NOT APPLICABLE
FLAMMABLE LIMITS(LEL): APPROXIMATELY 1.5 % VOLUME
FLAMMABLE LIMITS(UEL): APPROXIMATELY 8 % VOLUME
VAPOR PRESSURE: NOT APPLICABLE
VAPOR DENSITY: 2.97 [REF STD:AIR=1]
DENSITY: 0.64 G/ML
SPECIFIC GRAVITY: 0.640 [REF STD:WATER=1]
SOLUBILITY IN WATER: NIL
SOLUBILITY- NON-WATER: NO DATA AVAILABLE
PARTITION COEFFICIENT N-OCTANOL/ WATER: NO DATA AVAILABLE
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
DECOMPOSITION TEMPERATURE: NO DATA AVAILABLE
VISCOSITY: NOT APPLICABLE
HAZARDOUS AIR POLLUTANTS: 0 % WEIGHT [TEST METHOD:CALCULATED]
MOLECULAR WEIGHT: NO DATA AVAILABLE
VOLATILE ORGANIC COMPOUNDS:
<=606 G/L [TEST METHOD:CALCULATED SCAQMD RULE 443.1]
[DETAILS:MATERIAL VOC]
VOLATILE ORGANIC COMPOUNDS:
<=94.7 % [TEST METHOD:CALCULATED PER CARB TITLE 2]
SOLIDS CONTENT: 0 %
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL MAY BE REACTIVE WITH CERTAIN AGENTS UNDER CERTAIN CONDITIONS
- SEE THE REMAINING HEADINGS IN THIS SECTION.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID: HEAT
10.5. INCOMPATIBLE MATERIALS: STRONG OXIDIZING AGENTS
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR THE
SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT BELOW
THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
INTENTIONAL CONCENTRATION AND INHALATION MAY BE HARMFUL OR FATAL.
SIMPLE ASPHYXIATION:
SIGNS/SYMPTOMS MAY INCLUDE INCREASED HEART RATE, RAPID RESPIRATIONS,
DROWSINESS, HEADACHE, INCOORDINATION, ALTERED JUDGEMENT, NAUSEA, VOMITING,
LETHARGY, SEIZURES, COMA, AND MAY BE FATAL.
RESPIRATORY TRACT IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL DISCHARGE, HEADACHE,
HOARSENESS, AND NOSE AND THROAT PAIN.
MAY CAUSE ADDITIONAL HEALTH EFFECTS (SEE BELOW).
SKIN CONTACT:
FROSTBITE:
SIGNS/SYMPTOMS MAY INCLUDE INTENSE PAIN, DISCOLORATION OF SKIN, AND TISSUE
DESTRUCTION.
MILD SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE LOCALIZED REDNESS, SWELLING, ITCHING, AND
DRYNESS.
EYE CONTACT:
FROSTBITE:
SIGNS/SYMPTOMS MAY INCLUDE INTENSE PAIN, CLOUDING OF THE CORNEA, REDNESS,
SWELLING, AND BLINDNESS.
MODERATE EYE IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND BLURRED
OR HAZY VISION.
INGESTION:
GASTROINTESTINAL IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABDOMINAL PAIN, STOMACH UPSET, NAUSEA, VOMITING
AND DIARRHEA.
MAY CAUSE ADDITIONAL HEALTH EFFECTS (SEE BELOW).
ADDITIONAL HEALTH EFFECTS:
SINGLE EXPOSURE MAY CAUSE TARGET ORGAN EFFECTS:
CENTRAL NERVOUS SYSTEM (CNS) DEPRESSION:
SIGNS/SYMPTOMS MAY INCLUDE HEADACHE, DIZZINESS, DROWSINESS,
INCOORDINATION, NAUSEA, SLOWED REACTION TIME, SLURRED SPEECH, GIDDINESS,
AND UNCONSCIOUSNESS.
SINGLE EXPOSURE, ABOVE RECOMMENDED GUIDELINES, MAY CAUSE:
CARDIAC SENSITIZATION: SIGNS/SYMPTOMS MAY INCLUDE IRREGULAR HEARTBEAT
(ARRHYTHMIA), FAINTNESS, CHEST PAIN, AND MAY BE FATAL.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT DERMAL NO DATA AVAILABLE;
CALCULATED ATE >5,000 MG/KG
OVERALL PRODUCT INGESTION NO DATA AVAILABLE;
CALCULATED ATE >5,000 MG/KG
ISOBUTANE INHALATION- RAT LC50: 276,000 PPM
GAS (4
HOURS)
HEPTANE DERMAL RABBIT LD50: 3,000 MG/KG
HEPTANE INHALATION- RAT LC50: 103 MG/L
VAPOR (4
HOURS)
HEPTANE INGESTION RAT LD50: >15,000 MG/KG
POLY DERMAL RABBIT LD50: >19,400 MG/KG
(DIMETHYLSILOXANE)
POLY INGESTION RAT LD50: >17,000 MG/KG
(DIMETHYLSILOXANE)
ATE: ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
ISOBUTANE PROFESSIONAL NO SIGNIFICANT IRRITATION
JUDGEMENT
HEPTANE HUMAN MILD IRRITANT
POLY(DIMETHYLSILOXANE) RABBIT NO SIGNIFICANT IRRITATION
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
ISOBUTANE PROFESSIONAL NO SIGNIFICANT IRRITATION
JUDGEMENT
HEPTANE PROFESSIONAL MODERATE IRRITANT
JUDGEMENT
POLY(DIMETHYLSILOXANE) RABBIT NO SIGNIFICANT IRRITATION
SKIN SENSITIZATION:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
RESPIRATORY SENSITIZATION:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
ISOBUTANE IN VITRO NOT MUTAGENIC
HEPTANE IN VITRO NOT MUTAGENIC
CARCINOGENICITY:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
NAME ROUTE TARGET VALUE
ORGAN(S)
ISOBUTANE INHALATION CARDIAC SENSITIZATION CAUSES DAMAGE TO ORGANS
ISOBUTANE INHALATION CENTRAL NERVOUS MAY CAUSE DROWSINESS OR
SYSTEM DEPRESSION DIZZINESS
ISOBUTANE INHALATION RESPIRATORY NOT CLASSIFIED
IRRITATION
HEPTANE INHALATION CENTRAL NERVOUS MAY CAUSE DROWSINESS OR
SYSTEM DEPRESSION DIZZINESS
HEPTANE INHALATION RESPIRATORY SOME POSITIVE DATA EXIST,
IRRITATION BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
HEPTANE INGESTION CENTRAL NERVOUS MAY CAUSE DROWSINESS OR
SYSTEM DEPRESSION DIZZINESS
NAME SPECIES TEST RESULT EXPOSURE DURATION
ISOBUTANE MULTIPLE NOAEL NOT AVAILABLE
ANIMAL
SPECIES
ISOBUTANE HUMAN NOAEL NOT AVAILABLE
AND
ANIMAL
ISOBUTANE MOUSE NOAEL NOT AVAILABLE
HEPTANE HUMAN NOAEL NOT AVAILABLE
HEPTANE HUMAN NOAEL NOT AVAILABLE
HEPTANE HUMAN NOAEL NOT AVAILABLE
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
ISOBUTANE INHALATION KIDNEY AND/OR NOT CLASSIFIED
BLADDER
HEPTANE INHALATION LIVER | NERVOUS NOT CLASSIFIED
SYSTEM | KIDNEY
AND/OR BLADDER
NAME SPECIES TEST RESULT EXPOSURE DURATION
ISOBUTANE RAT NOAEL 13 WEEKS
4,500 PPM
HEPTANE RAT NOAEL 12 MG/L 26 WEEKS
ASPIRATION HAZARD:
NAME VALUE
HEPTANE ASPIRATION HAZARD
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED ON THE FIRST PAGE OF THE
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED ON THE FIRST PAGE OF THE
SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED ON THE FIRST PAGE OF THE
SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/ CONTAINER IN ACCORDANCE WITH THE LOCAL/REGIONAL/
NATIONAL/INTERNATIONAL REGULATIONS.
INCINERATE IN A PERMITTED WASTE INCINERATION FACILITY. AS A DISPOSAL
ALTERNATIVE, UTILIZE AN ACCEPTABLE PERMITTED WASTE DISPOSAL FACILITY.
EMPTY DRUMS/BARRELS/CONTAINERS USED FOR TRANSPORTING AND HANDLING
HAZARDOUS CHEMICALS (CHEMICAL SUBSTANCES/MIXTURES/PREPARATIONS CLASSIFIED
AS HAZARDOUS AS PER APPLICABLE REGULATIONS) SHALL BE CONSIDERED, STORED,
TREATED & DISPOSED OF AS HAZARDOUS WASTES UNLESS OTHERWISE DEFINED BY
APPLICABLE WASTE REGULATIONS. CONSULT WITH THE RESPECTIVE REGULATING
AUTHORITIES TO DETERMINE THE AVAILABLE TREATMENT AND DISPOSAL FACILITIES.
EPA HAZARDOUS WASTE NUMBER (RCRA): D001 (IGNITABLE)
| SECTION 14: TRANSPORT INFORMATION | |
FOR TRANSPORT INFORMATION, PLEASE VISIT HTTP://3M.COM/TRANSPORTINFO OR
CALL 1-800-364-3577 OR 651-737-6501.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
EPCRA 311/312 HAZARD CLASSIFICATIONS:
PHYSICAL HAZARDS:
FLAMMABLE (GASES, AEROSOLS, LIQUIDS, OR SOLIDS)
GAS UNDER PRESSURE
HEALTH HAZARDS:
SERIOUS EYE DAMAGE OR EYE IRRITATION
SIMPLE ASPHYXIANT
SPECIFIC TARGET ORGAN TOXICITY (SINGLE OR REPEATED EXPOSURE)
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
15.3. CHEMICAL INVENTORIES:
THE COMPONENTS OF THIS PRODUCT ARE IN COMPLIANCE WITH THE CHEMICAL
NOTIFICATION REQUIREMENTS OF TSCA. ALL REQUIRED COMPONENTS OF THIS
PRODUCT ARE LISTED ON THE ACTIVE PORTION OF THE TSCA INVENTORY.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 2
FLAMMABILITY 4
INSTABILITY 0
SPECIAL HAZARDS NONE
AEROSOL STORAGE CODE: 3
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED
FOR USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO
INCLUDE THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT
ARE KNOWN TO BE GENERATED IN SIGNIFICANT QUANTITIES.
DOCUMENT GROUP: 05-6937-6
ISSUE DATE: 05/21/18
VERSION NUMBER: 25.00
SUPERCEDES DATE: 01/18/18
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED.3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL,IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION,3MMAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM