| Common Name: | SCOTCH-WELD EPOXY ADHESIVE 2216 B/A TRANSLUCENT |
| Manufacturer: | 3M |
| SDS Revision Date: | 4/16/2015 |
| SDS Format: | GHS-US |
| Item Number(s): | 2JBL1, 2JBL2, 2JBY7, 2JBY8 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE 2216 B/A TRANSLUCENT
04/16/15
3M
SAFETY DATA SHEET
COPYRIGHT, 2015, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR THE
PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 11-3433-7
VERSION NUMBER: 10.00
ISSUE DATE: 04/16/15
SUPERCEDES DATE: 01/04/12
PRODUCT IDENTIFIER:
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE 2216 B/A TRANSLUCENT
ID NUMBER(S):
62-3508-0530-5, 62-3508-0535-4, 62-3508-5430-3, 62-3508-6430-2,
62-3508-7430-1
RECOMMENDED USE: STRUCTURAL ADHESIVE
SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: INDUSTRIAL ADHESIVES AND TAPES DIVISION
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
EMERGENCY TELEPHONE NUMBER: 1-800-364-3577 OR (651) 737-6501 (24 HOURS)
THIS PRODUCT IS A KIT OR A MULTIPART PRODUCT WHICH CONSISTS OF MULTIPLE,
INDEPENDENTLY PACKAGED COMPONENTS. A SAFETY DATA SHEET (SDS), ARTICLE
INFORMATION SHEET (AIS), OR ARTICLE INFORMATION LETTER (AIL) FOR EACH OF
THESE COMPONENTS IS INCLUDED. PLEASE DO NOT SEPARATE THE COMPONENT
DOCUMENTS FROM THIS COVER SHEET.
THE DOCUMENT NUMBERS FOR COMPONENTS OF THIS PRODUCT ARE:
10-3171-5, 10-3173-1
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED IN
ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE 2216 TRANSLUCENT PART B
04/16/15
3M
SAFETY DATA SHEET
COPYRIGHT, 2015, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR THE
PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 10-3171-5
VERSION NUMBER: 24.00
ISSUE DATE: 04/16/15
SUPERCEDES DATE: 01/04/12
| SECTION 1: IDENTIFICATION |  |
1.1. PRODUCT IDENTIFIER:
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE 2216 TRANSLUCENT PART B
PRODUCT IDENTIFICATION NUMBERS: 62-3508-8535-6, 62-3508-9530-6
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE:
PART B OF STRUCTURAL 2-COMPONENT EPOXY ADHESIVE, STRUCTURAL ADHESIVE
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: INDUSTRIAL ADHESIVES AND TAPES DIVISION
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
SERIOUS EYE DAMAGE/IRRITATION: CATEGORY 2B.
SKIN SENSITIZER: CATEGORY 1.
2.2. LABEL ELEMENTS:
SIGNAL WORD: WARNING
SYMBOLS: EXCLAMATION MARK |
PICTOGRAMS: EXCLAMATION MARK
HAZARD STATEMENTS:
CAUSES EYE IRRITATION.
MAY CAUSE AN ALLERGIC SKIN REACTION.
PRECAUTIONARY STATEMENTS:
PREVENTION:
AVOID BREATHING DUST/FUME/GAS/MIST/VAPORS/SPRAY.
WEAR PROTECTIVE GLOVES.
WASH THOROUGHLY AFTER HANDLING.
CONTAMINATED WORK CLOTHING MUST NOT BE ALLOWED OUT OF THE WORKPLACE.
RESPONSE:
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES, IF
PRESENT AND EASY TO DO. CONTINUE RINSING.
IF EYE IRRITATION PERSISTS: GET MEDICAL ADVICE/ATTENTION.
IF ON SKIN: WASH WITH PLENTY OF SOAP AND WATER.
IF SKIN IRRITATION OR RASH OCCURS: GET MEDICAL ADVICE/ATTENTION.
WASH CONTAMINATED CLOTHING BEFORE REUSE.
DISPOSAL:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH APPLICABLE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
2.3. HAZARDS NOT OTHERWISE CLASSIFIED: NONE.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
EPOXY RESIN 25068-38-6 100
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
IMMEDIATELY WASH WITH SOAP AND WATER. REMOVE CONTAMINATED CLOTHING AND WASH
BEFORE REUSE. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL ATTENTION.
EYE CONTACT:
FLUSH WITH LARGE AMOUNTS OF WATER. REMOVE CONTACT LENSES IF EASY TO DO.
CONTINUE RINSING. IF SIGNS/SYMPTOMS PERSIST, GET MEDICAL ATTENTION.
IF SWALLOWED: RINSE MOUTH. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED: NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
IN CASE OF FIRE:
USE A FIRE FIGHTING AGENT SUITABLE FOR ORDINARY COMBUSTIBLE MATERIAL SUCH
AS WATER OR FOAM TO EXTINGUISH.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
NONE INHERENT IN THIS PRODUCT.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
ALDEHYDES DURING COMBUSTION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
KETONES DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
NO SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS ARE ANTICIPATED.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
EVACUATE AREA. VENTILATE THE AREA WITH FRESH AIR. FOR LARGE SPILL, OR
SPILLS IN CONFINED SPACES, PROVIDE MECHANICAL VENTILATION TO DISPERSE OR
EXHAUST VAPORS, IN ACCORDANCE WITH GOOD INDUSTRIAL HYGIENE PRACTICE.
WARNING! A MOTOR COULD BE AN IGNITION SOURCE AND COULD CAUSE FLAMMABLE
GASES OR VAPORS IN THE SPILL AREA TO BURN OR EXPLODE. REFER TO OTHER
SECTIONS OF THIS SDS FOR INFORMATION REGARDING PHYSICAL AND HEALTH HAZARDS,
RESPIRATORY PROTECTION, VENTILATION, AND PERSONAL PROTECTIVE EQUIPMENT.
6.2. ENVIRONMENTAL PRECAUTIONS:
AVOID RELEASE TO THE ENVIRONMENT. FOR LARGER SPILLS, COVER DRAINS AND BUILD
DIKES TO PREVENT ENTRY INTO SEWER SYSTEMS OR BODIES OF WATER.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP:
CONTAIN SPILL. WORKING FROM AROUND THE EDGES OF THE SPILL INWARD, COVER
WITH BENTONITE, VERMICULITE, OR COMMERCIALLY AVAILABLE INORGANIC ABSORBENT
MATERIAL. MIX IN SUFFICIENT ABSORBENT UNTIL IT APPEARS DRY. REMEMBER,
ADDING AN ABSORBENT MATERIAL DOES NOT REMOVE A PHYSICAL, HEALTH, OR
ENVIRONMENTAL HAZARD. COLLECT AS MUCH OF THE SPILLED MATERIAL AS POSSIBLE.
PLACE IN A CLOSED CONTAINER APPROVED FOR TRANSPORTATION BY APPROPRIATE
AUTHORITIES. CLEAN UP RESIDUE WITH AN APPROPRIATE SOLVENT SELECTED BY A
QUALIFIED AND AUTHORIZED PERSON. VENTILATE THE AREA WITH FRESH AIR. READ
AND FOLLOW SAFETY PRECAUTIONS ON THE SOLVENT LABEL AND SDS. SEAL THE
CONTAINER. DISPOSE OF COLLECTED MATERIAL AS SOON AS POSSIBLE.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
FOR INDUSTRIAL OR PROFESSIONAL USE ONLY. AVOID BREATHING
DUST/FUME/GAS/MIST/VAPORS/SPRAY. DO NOT GET IN EYES, ON SKIN, OR ON
CLOTHING. DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT. WASH
THOROUGHLY AFTER HANDLING. CONTAMINATED WORK CLOTHING SHOULD NOT BE ALLOWED
OUT OF THE WORKPLACE. AVOID RELEASE TO THE ENVIRONMENT. WASH CONTAMINATED
CLOTHING BEFORE REUSE. AVOID CONTACT WITH OXIDIZING AGENTS (EG. CHLORINE,
CHROMIC ACID ETC.)
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
STORE AWAY FROM HEAT. STORE AWAY FROM ACIDS. STORE AWAY FROM OXIDIZING
AGENTS. STORE AWAY FROM AREAS WHERE PRODUCT MAY COME INTO CONTACT WITH FOOD
OR PHARMACEUTICALS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
NO OCCUPATIONAL EXPOSURE LIMIT VALUES EXIST FOR ANY OF THE COMPONENTS
LISTED IN SECTION 3 OF THIS SDS.
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO
CONTROL AIRBORNE EXPOSURES TO BELOW RELEVANT EXPOSURE LIMITS AND/OR CONTROL
DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS NOT ADEQUATE, USE
RESPIRATORY PROTECTION EQUIPMENT.
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON THE RESULTS
OF AN EXPOSURE ASSESSMENT. THE FOLLOWING EYE/FACE PROTECTION(S) ARE
RECOMMENDED: INDIRECT VENTED GOGGLES
SKIN/HAND PROTECTION:
SELECT AND USE GLOVES AND/OR PROTECTIVE CLOTHING APPROVED TO RELEVANT LOCAL
STANDARDS TO PREVENT SKIN CONTACT BASED ON THE RESULTS OF AN EXPOSURE
ASSESSMENT. SELECTION SHOULD BE BASED ON USE FACTORS SUCH AS EXPOSURE
LEVELS, CONCENTRATION OF THE SUBSTANCE OR MIXTURE, FREQUENCY AND DURATION,
PHYSICAL CHALLENGES SUCH AS TEMPERATURE EXTREMES, AND OTHER USE CONDITIONS.
CONSULT WITH YOUR GLOVE AND/OR PROTECTIVE CLOTHING MANUFACTURER FOR
SELECTION OF APPROPRIATE COMPATIBLE GLOVES/PROTECTIVE CLOTHING. NOTE:
NITRILE GLOVES MAY BE WORN OVER POLYMER LAMINATE GLOVES TO IMPROVE
DEXTERITY.
GLOVES MADE FROM THE FOLLOWING MATERIAL(S) ARE RECOMMENDED:
POLYMER LAMINATE
RESPIRATORY PROTECTION:
AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF A RESPIRATOR IS REQUIRED.
IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS PART OF A FULL RESPIRATORY
PROTECTION PROGRAM. BASED ON THE RESULTS OF THE EXPOSURE ASSESSMENT, SELECT
FROM THE FOLLOWING RESPIRATOR TYPE(S) TO REDUCE INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
ORGANIC VAPORS AND PARTICULATES
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: LIQUID
SPECIFIC PHYSICAL FORM: VISCOUS
ODOR, COLOR, GRADE: TRANSPARENT, EPOXY ODOR.
ODOR THRESHOLD: NO DATA AVAILABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: NOT APPLICABLE
FLASH POINT: 248 DEG. C [TEST METHOD: PENSKY-MARTENS CLOSED CUP]
EVAPORATION RATE: NOT APPLICABLE
FLAMMABILITY (SOLID, GAS): NOT APPLICABLE
FLAMMABLE LIMITS(LEL): NOT APPLICABLE
FLAMMABLE LIMITS(UEL): NOT APPLICABLE
VAPOR PRESSURE: </=0.03 MMHg [@ 77 DEG. C]
VAPOR DENSITY: NOT APPLICABLE
DENSITY: 1.17 G/ML
SPECIFIC GRAVITY: 1.17 [REF STD: WATER=1]
SOLUBILITY IN WATER: NIL
SOLUBILITY-NON-WATER: NO DATA AVAILABLE
PARTITION COEFFICIENT N-OCTANOL/WATER: NO DATA AVAILABLE
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
DECOMPOSITION TEMPERATURE: NO DATA AVAILABLE
VISCOSITY: APPROXIMATELY 14,000 CENTIPOISE
HAZARDOUS AIR POLLUTANTS: 0% WEIGHT [TEST METHOD: CALCULATED]
VOC LESS H2O & EXEMPT SOLVENTS:
3.9 G/L [TEST METHOD: CALCULATED SCAQMD RULE 443.1] [DETAILS: WHEN USED AS
INTENDED WITH PART A]
VOC LESS H2O & EXEMPT SOLVENTS:
0 G/L [TEST METHOD: CALCULATED SCAQMD RULE 443.1] [DETAILS: AS SUPPLIED]
VOC LESS H2O & EXEMPT SOLVENTS:
0.4% [TEST METHOD: CALCULATED SCAQMD RULE 443.1] [DETAILS: WHEN USED AS
INTENDED WITH PART A]
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL MAY BE REACTIVE WITH CERTAIN AGENTS UNDER CERTAIN CONDITIONS
- SEE THE REMAINING HEADINGS IN THIS SECTION.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID:
HEAT IS GENERATED DURING CURE. DO NOT CURE A MASS LARGER THAN 50 GRAMS IN A
CONFINED SPACE TO PREVENT A PREMATURE EXOTHERMIC REACTION WITH PRODUCTION
OF INTENSE HEAT AND SMOKE.
10.5. INCOMPATIBLE MATERIALS:
STRONG ACIDS
STRONG OXIDIZING AGENTS
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR THE
SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT BELOW
THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
THIS PRODUCT MAY HAVE A CHARACTERISTIC ODOR; HOWEVER, NO ADVERSE HEALTH
EFFECTS ARE ANTICIPATED.
SKIN CONTACT:
MILD SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE LOCALIZED REDNESS, SWELLING, ITCHING, AND
DRYNESS.
ALLERGIC SKIN REACTION (NON-PHOTO INDUCED):
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, BLISTERING, AND ITCHING.
EYE CONTACT:
MODERATE EYE IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND BLURRED OR
HAZY VISION.
INGESTION:
GASTROINTESTINAL IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABDOMINAL PAIN, STOMACH UPSET, NAUSEA, VOMITING
AND DIARRHEA.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
EPOXY RESIN DERMAL RAT LD50 >1,600 MG/KG
EPOXY RESIN INGESTION RAT LD50 >1,000 MG/KG
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
EPOXY RESIN RABBIT MILD IRRITANT
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
EPOXY RESIN RABBIT MODERATE IRRITANT
SKIN SENSITIZATION:
NAME SPECIES VALUE
EPOXY RESIN HUMAN AND ANIMAL SENSITIZING
RESPIRATORY SENSITIZATION:
NAME SPECIES VALUE
EPOXY RESIN HUMAN SOME POSITIVE DATA EXIST, BUT THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
EPOXY RESIN IN VIVO NOT MUTAGENIC
EPOXY RESIN IN VITRO SOME POSITIVE DATA EXIST, BUT THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION
CARCINOGENICITY:
NAME ROUTE SPECIES VALUE
EPOXY RESIN DERMAL MOUSE SOME POSITIVE DATA EXIST, BUT THE DATA ARE
NOT SUFFICIENT FOR CLASSIFICATION
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
NAME ROUTE VALUE SPECIES TEST RESULT EXPOSURE
DURATION
EPOXY RESIN INGESTION NOT TOXIC TO RAT NOAEL 750 2 GENERATION
FEMALE MG/KG/DAY
REPRODUCTION
EPOXY RESIN INGESTION NOT TOXIC TO RAT NOAEL 750 2 GENERATION
MALE MG/KG/DAY
REPRODUCTION
EPOXY RESIN DERMAL NOT TOXIC TO RABBIT NOAEL 300 DURING
DEVELOPMENT MG/KG/DAY ORGANOGENESIS
EPOXY RESIN INGESTION NOT TOXIC TO RAT NOAEL 750 2 GENERATION
DEVELOPMENT MG/KG/DAY
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
EPOXY RESIN DERMAL LIVER SOME POSITIVE DATA
EXIST, BUT THE DATA ARE
NOT SUFFICIENT FOR
CLASSIFICATION
EPOXY RESIN DERMAL NERVOUS SYSTEM ALL DATA ARE NEGATIVE
EPOXY RESIN INGESTION AUDITORY SYSTEM | HEART | ALL DATA ARE NEGATIVE
ENDOCRINE SYSTEM |
HEMATOPOIETIC SYSTEM |
LIVER | EYES | KIDNEY
AND/OR BLADDER
NAME SPECIES TEST RESULT EXPOSURE DURATION
EPOXY RESIN RAT NOAEL 1,000 MG/KG/DAY 2 YEARS
EPOXY RESIN RAT NOAEL 1,000 MG/KG/DAY 13 WEEKS
EPOXY RESIN RAT NOAEL 1,000 MG/KG/DAY 28 DAYS
ASPIRATION HAZARD:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH THE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
DISPOSE OF COMPLETELY CURED (OR POLYMERIZED) MATERIAL IN A PERMITTED
INDUSTRIAL WASTE FACILITY. AS A DISPOSAL ALTERNATIVE, INCINERATE UNCURED
PRODUCT IN A PERMITTED WASTE INCINERATION FACILITY. PROPER DESTRUCTION MAY
REQUIRE THE USE OF ADDITIONAL FUEL DURING INCINERATION PROCESSES.
COMBUSTION PRODUCTS WILL INCLUDE HALOGEN ACID (HCL/HF/HBR). FACILITY MUST
BE CAPABLE OF HANDLING HALOGENATED MATERIALS. IF NO OTHER DISPOSAL OPTIONS
ARE AVAILABLE, WASTE PRODUCT THAT HAS BEEN COMPLETELY CURED OR POLYMERIZED
MAY BE PLACED IN A LANDFILL PROPERLY DESIGNED FOR INDUSTRIAL WASTE. EMPTY
DRUMS/BARRELS/CONTAINERS USED FOR TRANSPORTING AND HANDLING HAZARDOUS
CHEMICALS (CHEMICAL SUBSTANCES/MIXTURES/PREPARATIONS CLASSIFIED AS
HAZARDOUS AS PER APPLICABLE REGULATIONS) SHALL BE CONSIDERED, STORED,
TREATED & DISPOSED OF AS HAZARDOUS WASTES UNLESS OTHERWISE DEFINED BY
APPLICABLE WASTE REGULATIONS. CONSULT WITH THE RESPECTIVE REGULATING
AUTHORITIES TO DETERMINE THE AVAILABLE TREATMENT AND DISPOSAL FACILITIES.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
| SECTION 14: TRANSPORT INFORMATION | |
FOR TRANSPORT INFORMATION, PLEASE VISIT HTTP://3M.COM/TRANSPORTINFO OR CALL
1-800-364-3577 OR 651-737-6501.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
311/312 HAZARD CATEGORIES:
FIRE HAZARD: NO
REACTIVITY HAZARD: NO
PRESSURE HAZARD: NO
IMMEDIATE HAZARD: YES
DELAYED HAZARD: NO
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
15.3. CHEMICAL INVENTORIES:
THE COMPONENTS OF THIS PRODUCT ARE IN COMPLIANCE WITH THE CHEMICAL
NOTIFICATION REQUIREMENTS OF TSCA.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 2
FLAMMABILITY 1
INSTABILITY 1
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED FOR
USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO INCLUDE
THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT ARE KNOWN
TO BE GENERATED IN SIGNIFICANT QUANTITIES.
DOCUMENT GROUP: 10-3171-5
VERSION NUMBER: 24.00
ISSUE DATE: 04/16/15
SUPERCEDES DATE: 01/04/12
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED IN
ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE 2216 TRANSLUCENT PART A
04/16/15
3M
SAFETY DATA SHEET
COPYRIGHT, 2015, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR THE
PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 10-3173-1
VERSION NUMBER: 25.00
ISSUE DATE: 04/16/15
SUPERCEDES DATE: 01/04/12
| SECTION 1: IDENTIFICATION | |
1.1. PRODUCT IDENTIFIER:
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE 2216 TRANSLUCENT PART A
PRODUCT IDENTIFICATION NUMBERS: 62-3608-8535-4, 62-3608-9530-4
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE: PART A OF TWO PART EPOXY ADHESIVE, STRUCTURAL ADHESIVE
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: INDUSTRIAL ADHESIVES AND TAPES DIVISION
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
ACUTE TOXICITY (DERMAL): CATEGORY 4.
SERIOUS EYE DAMAGE/IRRITATION: CATEGORY 1.
SKIN CORROSION/IRRITATION: CATEGORY 2.
SKIN SENSITIZER: CATEGORY 1.
REPRODUCTIVE TOXICITY: CATEGORY 1B.
2.2. LABEL ELEMENTS:
SIGNAL WORD: DANGER
SYMBOLS: CORROSION | EXCLAMATION MARK | HEALTH HAZARD |
PICTOGRAMS:
CORROSION
EXCLAMATION MARK
HEALTH HAZARD
HAZARD STATEMENTS:
HARMFUL IN CONTACT WITH SKIN.
CAUSES SERIOUS EYE DAMAGE.
CAUSES SKIN IRRITATION.
MAY CAUSE AN ALLERGIC SKIN REACTION.
MAY DAMAGE FERTILITY OR THE UNBORN CHILD.
PRECAUTIONARY STATEMENTS:
PREVENTION:
OBTAIN SPECIAL INSTRUCTIONS BEFORE USE.
DO NOT HANDLE UNTIL ALL SAFETY PRECAUTIONS HAVE BEEN READ AND UNDERSTOOD.
AVOID BREATHING DUST/FUME/GAS/MIST/VAPORS/SPRAY.
WEAR EYE/FACE PROTECTION.
WEAR PROTECTIVE GLOVES.
WASH THOROUGHLY AFTER HANDLING.
CONTAMINATED WORK CLOTHING MUST NOT BE ALLOWED OUT OF THE WORKPLACE.
RESPONSE:
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES, IF
PRESENT AND EASY TO DO. CONTINUE RINSING.
IF ON SKIN: WASH WITH PLENTY OF SOAP AND WATER.
IMMEDIATELY CALL A POISON CENTER OR DOCTOR/PHYSICIAN.
IF SKIN IRRITATION OR RASH OCCURS: GET MEDICAL ADVICE/ATTENTION.
TAKE OFF CONTAMINATED CLOTHING AND WASH IT BEFORE REUSE.
IF EXPOSED OR CONCERNED: GET MEDICAL ADVICE/ATTENTION.
STORAGE: STORE LOCKED UP.
DISPOSAL:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH APPLICABLE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
2.3. HAZARDS NOT OTHERWISE CLASSIFIED:
PERSONS PREVIOUSLY SENSITIZED TO AMINES MAY DEVELOP A CROSS-SENSITIZATION
REACTION TO CERTAIN OTHER AMINES.
90% OF THE MIXTURE CONSISTS OF INGREDIENTS OF UNKNOWN ACUTE ORAL TOXICITY.
90% OF THE MIXTURE CONSISTS OF INGREDIENTS OF UNKNOWN ACUTE DERMAL
TOXICITY.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
ALIPHATIC POLYMER DIAMINE 68911-25-1 80 - 90 TRADE SECRET *
BIS(3-AMINOPROPYL) ETHER 4246-51-9 10 - 20 TRADE SECRET *
OF DIETHYLENE GLYCOL
TOLUENE 108-88-3 <1 TRADE SECRET *
*THE SPECIFIC CHEMICAL IDENTITY AND/OR EXACT PERCENTAGE (CONCENTRATION) OF
THIS COMPOSITION HAS BEEN WITHHELD AS A TRADE SECRET.
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
IMMEDIATELY WASH WITH SOAP AND WATER. REMOVE CONTAMINATED CLOTHING AND WASH
BEFORE REUSE. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL ATTENTION.
EYE CONTACT:
IMMEDIATELY FLUSH WITH LARGE AMOUNTS OF WATER FOR AT LEAST 15 MINUTES.
REMOVE CONTACT LENSES IF EASY TO DO. CONTINUE RINSING. IMMEDIATELY GET
MEDICAL ATTENTION.
IF SWALLOWED: RINSE MOUTH. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED: NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
IN CASE OF FIRE:
USE A FIRE FIGHTING AGENT SUITABLE FOR ORDINARY COMBUSTIBLE MATERIAL SUCH
AS WATER OR FOAM TO EXTINGUISH.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
NONE INHERENT IN THIS PRODUCT.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
AMINE COMPOUNDS DURING COMBUSTION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
OXIDES OF NITROGEN DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
NO SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS ARE ANTICIPATED.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
EVACUATE AREA. VENTILATE THE AREA WITH FRESH AIR. FOR LARGE SPILL, OR
SPILLS IN CONFINED SPACES, PROVIDE MECHANICAL VENTILATION TO DISPERSE OR
EXHAUST VAPORS, IN ACCORDANCE WITH GOOD INDUSTRIAL HYGIENE PRACTICE.
WARNING!
A MOTOR COULD BE AN IGNITION SOURCE AND COULD CAUSE FLAMMABLE GASES OR
VAPORS IN THE SPILL AREA TO BURN OR EXPLODE. REFER TO OTHER SECTIONS OF
THIS SDS FOR INFORMATION REGARDING PHYSICAL AND HEALTH HAZARDS, RESPIRATORY
PROTECTION, VENTILATION, AND PERSONAL PROTECTIVE EQUIPMENT.
6.2. ENVIRONMENTAL PRECAUTIONS:
AVOID RELEASE TO THE ENVIRONMENT. FOR LARGER SPILLS, COVER DRAINS AND BUILD
DIKES TO PREVENT ENTRY INTO SEWER SYSTEMS OR BODIES OF WATER.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP:
CONTAIN SPILL. WORKING FROM AROUND THE EDGES OF THE SPILL INWARD, COVER
WITH BENTONITE, VERMICULITE, OR COMMERCIALLY AVAILABLE INORGANIC ABSORBENT
MATERIAL. MIX IN SUFFICIENT ABSORBENT UNTIL IT APPEARS DRY. REMEMBER,
ADDING AN ABSORBENT MATERIAL DOES NOT REMOVE A PHYSICAL, HEALTH, OR
ENVIRONMENTAL HAZARD. COLLECT AS MUCH OF THE SPILLED MATERIAL AS POSSIBLE.
PLACE IN A CLOSED CONTAINER APPROVED FOR TRANSPORTATION BY APPROPRIATE
AUTHORITIES. CLEAN UP RESIDUE WITH AN APPROPRIATE SOLVENT SELECTED BY A
QUALIFIED AND AUTHORIZED PERSON. VENTILATE THE AREA WITH FRESH AIR. READ
AND FOLLOW SAFETY PRECAUTIONS ON THE SOLVENT LABEL AND SDS. SEAL THE
CONTAINER. DISPOSE OF COLLECTED MATERIAL AS SOON AS POSSIBLE.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
FOR INDUSTRIAL OR PROFESSIONAL USE ONLY. DO NOT USE IN A CONFINED AREA WITH
MINIMAL AIR EXCHANGE. DO NOT HANDLE UNTIL ALL SAFETY PRECAUTIONS HAVE BEEN
READ AND UNDERSTOOD. DO NOT BREATHE DUST/FUME/GAS/MIST/VAPORS/SPRAY. DO NOT
GET IN EYES, ON SKIN, OR ON CLOTHING. DO NOT EAT, DRINK OR SMOKE WHEN USING
THIS PRODUCT. WASH THOROUGHLY AFTER HANDLING. CONTAMINATED WORK CLOTHING
SHOULD NOT BE ALLOWED OUT OF THE WORKPLACE. WASH CONTAMINATED CLOTHING
BEFORE REUSE. AVOID CONTACT WITH OXIDIZING AGENTS (EG. CHLORINE, CHROMIC
ACID ETC.) USE PERSONAL PROTECTIVE EQUIPMENT (GLOVES, RESPIRATORS, ETC.) AS
REQUIRED.
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
STORE AWAY FROM HEAT. STORE AWAY FROM OXIDIZING AGENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN THE TABLE
BELOW, AN OCCUPATIONAL EXPOSURE LIMIT IS NOT AVAILABLE FOR THE COMPONENT.
INGREDIENT C.A.S. NO. AGENCY LIMIT TYPE ADDITIONAL COMMENTS
TOLUENE 108-88-3 OSHA TWA: 200 PPM;
CEIL: 300 PPM
TOLUENE 108-88-3 ACGIH TWA: 20 PPM A4: NOT CLASS. AS HUMAN
CARCIN
TOLUENE 108-88-3 CMRG STEL: 75 PPM SKIN NOTATION
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
AIHA: AMERICAN INDUSTRIAL HYGIENE ASSOCIATION
CMRG: CHEMICAL MANUFACTURER'S RECOMMENDED GUIDELINES
OSHA:
UNITED STATES DEPARTMENT OF LABOR - OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION
TWA: TIME-WEIGHTED-AVERAGE
STEL: SHORT TERM EXPOSURE LIMIT
CEIL: CEILING
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO
CONTROL AIRBORNE EXPOSURES TO BELOW RELEVANT EXPOSURE LIMITS AND/OR
CONTROL DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS NOT ADEQUATE,
USE RESPIRATORY PROTECTION EQUIPMENT.
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON THE RESULTS
OF AN EXPOSURE ASSESSMENT. THE FOLLOWING EYE/FACE PROTECTION(S) ARE
RECOMMENDED:
FULL FACE SHIELD
INDIRECT VENTED GOGGLES
SKIN/HAND PROTECTION:
SELECT AND USE GLOVES AND/OR PROTECTIVE CLOTHING APPROVED TO RELEVANT LOCAL
STANDARDS TO PREVENT SKIN CONTACT BASED ON THE RESULTS OF AN EXPOSURE
ASSESSMENT. SELECTION SHOULD BE BASED ON USE FACTORS SUCH AS EXPOSURE
LEVELS, CONCENTRATION OF THE SUBSTANCE OR MIXTURE, FREQUENCY AND DURATION,
PHYSICAL CHALLENGES SUCH AS TEMPERATURE EXTREMES, AND OTHER USE CONDITIONS.
CONSULT WITH YOUR GLOVE AND/OR PROTECTIVE CLOTHING MANUFACTURER FOR
SELECTION OF APPROPRIATE COMPATIBLE GLOVES/PROTECTIVE CLOTHING. NOTE:
NITRILE GLOVES MAY BE WORN OVER POLYMER LAMINATE GLOVES TO IMPROVE
DEXTERITY.
GLOVES MADE FROM THE FOLLOWING MATERIAL(S) ARE RECOMMENDED:
POLYMER LAMINATE
RESPIRATORY PROTECTION:
AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF A RESPIRATOR IS REQUIRED.
IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS PART OF A FULL RESPIRATORY
PROTECTION PROGRAM. BASED ON THE RESULTS OF THE EXPOSURE ASSESSMENT, SELECT
FROM THE FOLLOWING RESPIRATOR TYPE(S) TO REDUCE INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
ORGANIC VAPORS AND PARTICULATES
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: LIQUID
SPECIFIC PHYSICAL FORM: VISCOUS
ODOR, COLOR, GRADE: AMBER, PUNGENT ODOR.
ODOR THRESHOLD: NO DATA AVAILABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: NOT APPLICABLE
FLASH POINT: >/=94 DEG. C [TEST METHOD: ESTIMATED]
EVAPORATION RATE: NOT APPLICABLE
FLAMMABILITY (SOLID, GAS): NOT APPLICABLE
FLAMMABLE LIMITS(LEL): NO DATA AVAILABLE
FLAMMABLE LIMITS(UEL): NO DATA AVAILABLE
VAPOR PRESSURE: </=0.01 MMHg [@ 20 DEG. C]
VAPOR DENSITY: NOT APPLICABLE
DENSITY: 0.97 G/ML
SPECIFIC GRAVITY: 0.970 [REF STD: WATER=1]
SOLUBILITY IN WATER: NIL
SOLUBILITY-NON-WATER: NO DATA AVAILABLE
PARTITION COEFFICIENT N-OCTANOL/WATER: NO DATA AVAILABLE
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
DECOMPOSITION TEMPERATURE: NO DATA AVAILABLE
VISCOSITY: APPROXIMATELY 7,000 CENTIPOISE [@ 20 DEG. C]
HAZARDOUS AIR POLLUTANTS: <0.3% WEIGHT [TEST METHOD: CALCULATED]
VOC LESS H2O & EXEMPT SOLVENTS:
3.9 G/L [TEST METHOD: CALCULATED SCAQMD RULE 443.1] [DETAILS: WHEN USED AS
INTENDED WITH PART B]
VOC LESS H2O & EXEMPT SOLVENTS:
<10 G/L [TEST METHOD: CALCULATED SCAQMD RULE 443.1] [DETAILS: AS SUPPLIED]
VOC LESS H2O & EXEMPT SOLVENTS:
0.4% [TEST METHOD: CALCULATED SCAQMD RULE 443.1] [DETAILS: WHEN USED AS
INTENDED WITH PART B]
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL MAY BE REACTIVE WITH CERTAIN AGENTS UNDER CERTAIN CONDITIONS
- SEE THE REMAINING HEADINGS IN THIS SECTION.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID:
HEAT IS GENERATED DURING CURE. DO NOT CURE A MASS LARGER THAN 50 GRAMS IN A
CONFINED SPACE TO PREVENT A PREMATURE EXOTHERMIC REACTION WITH PRODUCTION
OF INTENSE HEAT AND SMOKE.
10.5. INCOMPATIBLE MATERIALS: STRONG OXIDIZING AGENTS
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR THE
SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT BELOW
THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
RESPIRATORY TRACT IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL DISCHARGE, HEADACHE,
HOARSENESS, AND NOSE AND THROAT PAIN.
MAY CAUSE ADDITIONAL HEALTH EFFECTS (SEE BELOW).
SKIN CONTACT: HARMFUL IN CONTACT WITH SKIN.
SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE LOCALIZED REDNESS, SWELLING, ITCHING, DRYNESS,
CRACKING, BLISTERING, AND PAIN.
ALLERGIC SKIN REACTION (NON-PHOTO INDUCED):
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, BLISTERING, AND ITCHING.
EYE CONTACT:
CORROSIVE (EYE BURNS):
SIGNS/SYMPTOMS MAY INCLUDE CLOUDY APPEARANCE OF THE CORNEA, CHEMICAL BURNS,
SEVERE PAIN, TEARING, ULCERATIONS, SIGNIFICANTLY IMPAIRED VISION OR
COMPLETE LOSS OF VISION.
INGESTION: MAY BE HARMFUL IF SWALLOWED.
GASTROINTESTINAL IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABDOMINAL PAIN, STOMACH UPSET, NAUSEA, VOMITING
AND DIARRHEA.
MAY CAUSE ADDITIONAL HEALTH EFFECTS (SEE BELOW).
ADDITIONAL HEALTH EFFECTS:
REPRODUCTIVE/DEVELOPMENTAL TOXICITY:
CONTAINS A CHEMICAL OR CHEMICALS WHICH CAN CAUSE BIRTH DEFECTS OR OTHER
REPRODUCTIVE HARM.
ADDITIONAL INFORMATION:
PERSONS PREVIOUSLY SENSITIZED TO AMINES MAY DEVELOP A CROSS-SENSITIZATION
REACTION TO CERTAIN OTHER AMINES.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT DERMAL NO DATA AVAILABLE; CALCULATED ATE
1,000 - 2,000 MG/KG
OVERALL PRODUCT INGESTION NO DATA AVAILABLE; CALCULATED ATE
2,000 - 5,000 MG/KG
BIS(3-AMINOPROPYL) DERMAL RABBIT LD50 2,500 MG/KG
ETHER OF
DIETHYLENE GLYCOL
BIS(3-AMINOPROPYL) INGESTION RAT LD50 3,160 MG/KG
ETHER OF
DIETHYLENE GLYCOL
TOLUENE DERMAL RAT LD50 12,000 MG/KG
TOLUENE INHALATION- RAT LC50 30 MG/L
VAPOR (4
HOURS)
TOLUENE INGESTION RAT LD50 5,550 MG/KG
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
OVERALL PRODUCT IRRITANT
ALIPHATIC POLYMER DIAMINE RABBIT IRRITANT
BIS(3-AMINOPROPYL) ETHER OF DIETHYLENE GLYCOL RABBIT CORROSIVE
TOLUENE RABBIT IRRITANT
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
ALIPHATIC POLYMER DIAMINE SIMILAR HEALTH HAZARDS CORROSIVE
BIS(3-AMINOPROPYL) ETHER SIMILAR HEALTH HAZARDS CORROSIVE
OF DIETHYLENE GLYCOL
TOLUENE RABBIT MODERATE IRRITANT
SKIN SENSITIZATION:
NAME SPECIES VALUE
OVERALL PRODUCT SENSITIZING
ALIPHATIC POLYMER DIAMINE GUINEA PIG SENSITIZING
TOLUENE GUINEA PIG NOT SENSITIZING
RESPIRATORY SENSITIZATION:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
TOLUENE IN VITRO NOT MUTAGENIC
TOLUENE IN VIVO NOT MUTAGENIC
CARCINOGENICITY:
NAME ROUTE SPECIES VALUE
TOLUENE DERMAL MOUSE SOME POSITIVE DATA EXIST, BUT THE DATA ARE
NOT SUFFICIENT FOR CLASSIFICATION
TOLUENE INGESTION RAT SOME POSITIVE DATA EXIST, BUT THE DATA ARE
NOT SUFFICIENT FOR CLASSIFICATION
TOLUENE INHALATION MOUSE SOME POSITIVE DATA EXIST, BUT THE DATA ARE
NOT SUFFICIENT FOR CLASSIFICATION
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
NAME ROUTE VALUE SPECIES TEST RESULT EXPOSURE
DURATION
TOLUENE INHALATION SOME POSITIVE HUMAN NOAEL NOT OCCUPATIONAL
FEMALE AVAILABLE EXPOSURE
REPRODUCTIVE
DATA EXIST,
BUT THE DATA
ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INHALATION SOME POSITIVE RAT NOAEL 2.3 MG/L 1 GENERATION
MALE
REPRODUCTIVE
DATA EXIST,
BUT THE DATA
ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INGESTION TOXIC TO RAT LOAEL 520 DURING
DEVELOPMENT MG/KG/DAY GESTATION
TOLUENE INHALATION TOXIC TO HUMAN NOAEL NOT POISONING
DEVELOPMENT AVAILABLE AND/OR ABUSE
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
BIS(3-AMINOPROPYL) INHALATION RESPIRATORY SOME POSITIVE DATA EXIST,
ETHER OF IRRITATION BUT THE DATA ARE NOT
DIETHYLENE GLYCOL SUFFICIENT FOR
CLASSIFICATION
TOLUENE INHALATION CENTRAL NERVOUS MAY CAUSE DROWSINESS OR
SYSTEM DIZZINESS
DEPRESSION
TOLUENE INHALATION RESPIRATORY SOME POSITIVE DATA EXIST,
IRRITATION BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INHALATION IMMUNE SYSTEM SOME POSITIVE DATA EXIST,
BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INGESTION CENTRAL NERVOUS MAY CAUSE DROWSINESS OR
SYSTEM DIZZINESS
DEPRESSION
NAME SPECIES TEST RESULT EXPOSURE DURATION
BIS(3-AMINOPROPYL) NOAEL NOT AVAILABLE
ETHER OF
DIETHYLENE GLYCOL
TOLUENE HUMAN NOAEL NOT AVAILABLE
TOLUENE HUMAN NOAEL NOT AVAILABLE
TOLUENE MOUSE NOAEL 0.004 MG/L 3 HOURS
TOLUENE HUMAN NOAEL NOT AVAILABLE POISONING AND/OR ABUSE
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
TOLUENE INHALATION AUDITORY SYSTEM | NERVOUS CAUSES DAMAGE TO ORGANS
SYSTEM | EYES | OLFACTORY THROUGH PROLONGED OR
SYSTEM REPEATED EXPOSURE
TOLUENE INHALATION RESPIRATORY SYSTEM SOME POSITIVE DATA EXIST,
BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INHALATION HEART | LIVER | KIDNEY SOME POSITIVE DATA EXIST,
AND/OR BLADDER BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INHALATION ENDOCRINE SYSTEM SOME POSITIVE DATA EXIST,
BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INHALATION IMMUNE SYSTEM SOME POSITIVE DATA EXIST,
BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INHALATION BONE, TEETH, NAILS, SOME POSITIVE DATA EXIST,
AND/OR HAIR BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INHALATION HEMATOPOIETIC SYSTEM | SOME POSITIVE DATA EXIST,
VASCULAR SYSTEM BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INGESTION NERVOUS SYSTEM SOME POSITIVE DATA EXIST,
BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INGESTION HEART SOME POSITIVE DATA EXIST,
BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INGESTION LIVER | KIDNEY AND/OR SOME POSITIVE DATA EXIST,
BLADDER BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INGESTION HEMATOPOIETIC SYSTEM SOME POSITIVE DATA EXIST,
BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INGESTION ENDOCRINE SYSTEM SOME POSITIVE DATA EXIST,
BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TOLUENE INGESTION IMMUNE SYSTEM SOME POSITIVE DATA EXIST,
BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
NAME SPECIES TEST RESULT EXPOSURE DURATION
TOLUENE HUMAN NOAEL NOT AVAILABLE POISONING AND/OR
ABUSE
TOLUENE RAT LOAEL 2.3 MG/L 15 MONTHS
TOLUENE RAT NOAEL 11.3 MG/L 15 WEEKS
TOLUENE RAT NOAEL 1.1 MG/L 4 WEEKS
TOLUENE MOUSE NOAEL NOT AVAILABLE 20 DAYS
TOLUENE MOUSE NOAEL 1.1 MG/L 8 WEEKS
TOLUENE HUMAN NOAEL NOT AVAILABLE OCCUPATIONAL
EXPOSURE
TOLUENE RAT NOAEL 625 MG/KG/DAY 13 WEEKS
TOLUENE RAT NOAEL 2,500 MG/KG/DAY 13 WEEKS
TOLUENE MULTIPLE ANIMAL SPECIES NOAEL 2,500 MG/KG/DAY 13 WEEKS
TOLUENE MOUSE NOAEL 600 MG/KG/DAY 14 DAYS
TOLUENE MOUSE NOAEL 105 MG/KG/DAY 28 DAYS
TOLUENE MOUSE NOAEL 105 MG/KG/DAY 4 WEEKS
ASPIRATION HAZARD:
NAME VALUE
TOLUENE ASPIRATION HAZARD
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH THE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
DISPOSE OF COMPLETELY CURED (OR POLYMERIZED) MATERIAL IN A PERMITTED
INDUSTRIAL WASTE FACILITY. AS A DISPOSAL ALTERNATIVE, INCINERATE UNCURED
PRODUCT IN A PERMITTED WASTE INCINERATION FACILITY. PROPER DESTRUCTION MAY
REQUIRE THE USE OF ADDITIONAL FUEL DURING INCINERATION PROCESSES. IF NO
OTHER DISPOSAL OPTIONS ARE AVAILABLE, WASTE PRODUCT THAT HAS BEEN
COMPLETELY CURED OR POLYMERIZED MAY BE PLACED IN A LANDFILL PROPERLY
DESIGNED FOR INDUSTRIAL WASTE. EMPTY DRUMS/BARRELS/CONTAINERS USED FOR
TRANSPORTING AND HANDLING HAZARDOUS CHEMICALS (CHEMICAL
SUBSTANCES/MIXTURES/PREPARATIONS CLASSIFIED AS HAZARDOUS AS PER APPLICABLE
REGULATIONS) SHALL BE CONSIDERED, STORED, TREATED & DISPOSED OF AS
HAZARDOUS WASTES UNLESS OTHERWISE DEFINED BY APPLICABLE WASTE REGULATIONS.
CONSULT WITH THE RESPECTIVE REGULATING AUTHORITIES TO DETERMINE THE
AVAILABLE TREATMENT AND DISPOSAL FACILITIES.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
| SECTION 14: TRANSPORT INFORMATION | |
FOR TRANSPORT INFORMATION, PLEASE VISIT HTTP://3M.COM/TRANSPORTINFO OR CALL
1-800-364-3577 OR 651-737-6501.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
311/312 HAZARD CATEGORIES:
FIRE HAZARD: NO
REACTIVITY HAZARD: NO
PRESSURE HAZARD: NO
IMMEDIATE HAZARD: YES
DELAYED HAZARD: YES
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
15.3. CHEMICAL INVENTORIES:
THE COMPONENTS OF THIS PRODUCT ARE IN COMPLIANCE WITH THE CHEMICAL
NOTIFICATION REQUIREMENTS OF TSCA.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 3
FLAMMABILITY 1
INSTABILITY 1
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED FOR
USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO INCLUDE
THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT ARE KNOWN
TO BE GENERATED IN SIGNIFICANT QUANTITIES.
DOCUMENT GROUP: 10-3173-1
VERSION NUMBER: 25.00
ISSUE DATE: 04/16/15
SUPERCEDES DATE: 01/04/12
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED IN
ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM