| Common Name: | SCOTCH-WELD EPOXY ADHESIVE DP110 GRAY |
| Manufacturer: | 3M |
| SDS Revision Date: | 6/29/2017 |
| SDS Format: | GHS-US |
| Item Number(s): | 2JBZ3, 489J91 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP110 GRAY
06/29/17
3M
SAFETY DATA SHEET
COPYRIGHT,2017,3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR THE
PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 11-3324-8
VERSION NUMBER: 16.01
ISSUE DATE: 06/29/17
SUPERCEDES DATE: 04/16/15
PRODUCT IDENTIFIER:
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP110 GRAY
ID NUMBER(S):
62-3533-1431-3, 62-3533-1434-7, 62-3533-1436-2, 62-3533-1437-0,
62-3533-3530-0, 62-3533-3830-4
RECOMMENDED USE: STRUCTURAL ADHESIVE
SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: INDUSTRIAL ADHESIVES AND TAPES DIVISION
ADDRESS:
3M CENTER,
ST. PAUL
MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
THIS PRODUCT IS A KIT OR A MULTIPART PRODUCT WHICH CONSISTS OF MULTIPLE,
INDEPENDENTLY PACKAGED COMPONENTS. A SAFETY DATA SHEET (SDS), ARTICLE
INFORMATION SHEET (AIS), OR ARTICLE INFORMATION LETTER (AIL) FOR EACH OF
THESE COMPONENTS IS INCLUDED. PLEASE DO NOT SEPARATE THE COMPONENT
DOCUMENTS FROM THIS COVER SHEET.
THE DOCUMENT NUMBERS FOR COMPONENTS OF THIS PRODUCT ARE:
22-1043-3, 11-3320-6
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE3MPRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A3MPRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL,IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP110 GRAY, PART A OR EPOXY ADHESIVE
110 GRAY, PART A
12/11/17
3M
SAFETY DATA SHEET
COPYRIGHT,2017,3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR THE
PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 22-1043-3
VERSION NUMBER: 7.00
ISSUE DATE: 12/11/17
SUPERCEDES DATE: 10/28/16
| SECTION 1: IDENTIFICATION |  |
1.1. PRODUCT IDENTIFIER:
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP110 GRAY, PART A OR EPOXY ADHESIVE
110 GRAY, PART A
PRODUCT IDENTIFICATION NUMBERS: 62-3633-8531-1
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE: STRUCTURAL ADHESIVE
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: INDUSTRIAL ADHESIVES AND TAPES DIVISION
ADDRESS:
3M CENTER,
ST. PAUL
MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
SERIOUS EYE DAMAGE/IRRITATION: CATEGORY 2A.
SKIN CORROSION/IRRITATION: CATEGORY 2.
SKIN SENSITIZER: CATEGORY 1A.
2.2. LABEL ELEMENTS:
SIGNAL WORD: WARNING
SYMBOLS: EXCLAMATION MARK |
PICTOGRAMS: EXCLAMATION MARK
HAZARD STATEMENTS:
CAUSES SERIOUS EYE IRRITATION.
CAUSES SKIN IRRITATION.
MAY CAUSE AN ALLERGIC SKIN REACTION.
PRECAUTIONARY STATEMENTS:
PREVENTION:
AVOID BREATHING DUST/FUME/GAS/MIST/VAPORS/SPRAY.
WEAR PROTECTIVE GLOVES AND EYE/FACE PROTECTION.
WASH THOROUGHLY AFTER HANDLING.
CONTAMINATED WORK CLOTHING MUST NOT BE ALLOWED OUT OF THE WORKPLACE.
RESPONSE:
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES,
IF PRESENT AND EASY TO DO. CONTINUE RINSING.
IF EYE IRRITATION PERSISTS: GET MEDICAL ADVICE/ATTENTION.
IF ON SKIN: WASH WITH PLENTY OF SOAP AND WATER.
IF SKIN IRRITATION OR RASH OCCURS: GET MEDICAL ADVICE/ATTENTION.
TAKE OFF CONTAMINATED CLOTHING AND WASH IT BEFORE REUSE.
DISPOSAL:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH APPLICABLE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
2% OF THE MIXTURE CONSISTS OF INGREDIENTS OF UNKNOWN ACUTE ORAL TOXICITY.
2% OF THE MIXTURE CONSISTS OF INGREDIENTS OF UNKNOWN ACUTE DERMAL TOXICITY.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
MERCAPTAN POLYMER (NJTS REG. NO. TRADE SECRET* 40 - 80 TRADE SECRET *
04499600-6776)
POLYAMIDE RESIN 68410-23-1 5 - 30 TRADE SECRET *
MODIFIED EPOXY RESIN (NJTS REG. TRADE SECRET* 10 - 30 TRADE SECRET *
NO. 04499600-6838)
HYDROGENATED TERPHENYL 61788-32-7 5 - 10 TRADE SECRET *
2,4,6-TRIS[(DIMETHYLAMINO) 90-72-2 1 - 5 TRADE SECRET *
METHYL]PHENOL
HYDROGENATED POLYPHENYLS 68956-74-1 1 - 5 TRADE SECRET *
TRIETHYLENETETRAMINE 112-24-3 0.5 - 2 TRADE SECRET *
CARBON BLACK 1333-86-4 0.1 - 1 TRADE SECRET *
NJTS OR NJTSRN: NEW JERSEY TRADE SECRET REGISTRY NUMBER.
*THE SPECIFIC CHEMICAL IDENTITY AND/OR EXACT PERCENTAGE (CONCENTRATION)
OF THIS COMPOSITION HAS BEEN WITHHELD AS A TRADE SECRET.
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
IMMEDIATELY WASH WITH SOAP AND WATER. REMOVE CONTAMINATED CLOTHING AND
WASH BEFORE REUSE. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL ATTENTION.
EYE CONTACT:
IMMEDIATELY FLUSH WITH LARGE AMOUNTS OF WATER. REMOVE CONTACT LENSES IF
EASY TO DO. CONTINUE RINSING. GET MEDICAL ATTENTION.
IF SWALLOWED:
RINSE MOUTH. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED:
NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
IN CASE OF FIRE:
USE A FIRE FIGHTING AGENT SUITABLE FOR ORDINARY COMBUSTIBLE MATERIAL SUCH
AS WATER OR FOAM TO EXTINGUISH.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
NONE INHERENT IN THIS PRODUCT.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
ALDEHYDES DURING COMBUSTION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
NO SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS ARE ANTICIPATED.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
EVACUATE AREA. VENTILATE THE AREA WITH FRESH AIR. FOR LARGE SPILL, OR
SPILLS IN CONFINED SPACES, PROVIDE MECHANICAL VENTILATION TO DISPERSE OR
EXHAUST VAPORS, IN ACCORDANCE WITH GOOD INDUSTRIAL HYGIENE PRACTICE. REFER
TO OTHER SECTIONS OF THIS SDS FOR INFORMATION REGARDING PHYSICAL AND HEALTH
HAZARDS, RESPIRATORY PROTECTION, VENTILATION, AND PERSONAL PROTECTIVE
EQUIPMENT.
6.2. ENVIRONMENTAL PRECAUTIONS:
AVOID RELEASE TO THE ENVIRONMENT. FOR LARGER SPILLS, COVER DRAINS AND BUILD
DIKES TO PREVENT ENTRY INTO SEWER SYSTEMS OR BODIES OF WATER.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP:
WORKING FROM AROUND THE EDGES OF THE SPILL INWARD, COVER WITH BENTONITE,
VERMICULITE, OR COMMERCIALLY AVAILABLE INORGANIC ABSORBENT MATERIAL. MIX
IN SUFFICIENT ABSORBENT UNTIL IT APPEARS DRY. REMEMBER, ADDING AN ABSORBENT
MATERIAL DOES NOT REMOVE A PHYSICAL, HEALTH, OR ENVIRONMENTAL HAZARD.
COLLECT AS MUCH OF THE SPILLED MATERIAL AS POSSIBLE. PLACE IN A CLOSED
CONTAINER APPROVED FOR TRANSPORTATION BY APPROPRIATE AUTHORITIES. CLEAN UP
RESIDUE WITH AN APPROPRIATE SOLVENT SELECTED BY A QUALIFIED AND AUTHORIZED
PERSON. VENTILATE THE AREA WITH FRESH AIR. READ AND FOLLOW SAFETY
PRECAUTIONS ON THE SOLVENT LABEL AND SDS. SEAL THE CONTAINER. DISPOSE OF
COLLECTED MATERIAL AS SOON AS POSSIBLE IN ACCORDANCE WITH APPLICABLE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
FOR INDUSTRIAL OR PROFESSIONAL USE ONLY. AVOID BREATHING
DUST/FUME/GAS/MIST/VAPORS/SPRAY. DO NOT GET IN EYES, ON SKIN, OR ON
CLOTHING. DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT. WASH
THOROUGHLY AFTER HANDLING. CONTAMINATED WORK CLOTHING SHOULD NOT BE
ALLOWED OUT OF THE WORKPLACE. AVOID RELEASE TO THE ENVIRONMENT. WASH
CONTAMINATED CLOTHING BEFORE REUSE. AVOID CONTACT WITH OXIDIZING AGENTS
(EG. CHLORINE, CHROMIC ACID ETC.)
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
STORE AWAY FROM ACIDS. STORE AWAY FROM STRONG BASES. STORE AWAY FROM
OXIDIZING AGENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN THE TABLE
BELOW, AN OCCUPATIONAL EXPOSURE LIMIT IS NOT AVAILABLE FOR THE COMPONENT.
INGREDIENT C.A.S. NO. AGENCY LIMIT TYPE ADDITIONAL
COMMENTS
TRIETHYLENETETRAMINE 112-24-3 AIHA TWA:6 MG/M3 SKIN
(1 PPM)
CARBON BLACK 1333-86-4 ACGIH TWA(INHALABLE A3:
FRACTION): CONFIRMED
3 MG/M3 ANIMAL
CARCIN.
CARBON BLACK 1333-86-4 OSHA TWA:3.5 MG/M3
HYDROGENATED 61788-32-7 ACGIH TWA:0.5 PPM
TERPHENYL
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
AIHA: AMERICAN INDUSTRIAL HYGIENE ASSOCIATION
CMRG: CHEMICAL MANUFACTURER'S RECOMMENDED GUIDELINES
OSHA:
UNITED STATES DEPARTMENT OF LABOR - OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION
TWA: TIME-WEIGHTED-AVERAGE
STEL: SHORT TERM EXPOSURE LIMIT
CEIL: CEILING
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO
CONTROL AIRBORNE EXPOSURES TO BELOW RELEVANT EXPOSURE LIMITS AND/OR
CONTROL DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS NOT ADEQUATE,
USE RESPIRATORY PROTECTION EQUIPMENT.
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON THE
RESULTS OF AN EXPOSURE ASSESSMENT. THE FOLLOWING EYE/FACE PROTECTION(S)
ARE RECOMMENDED:
INDIRECT VENTED GOGGLES
SKIN/HAND PROTECTION:
SELECT AND USE GLOVES AND/OR PROTECTIVE CLOTHING APPROVED TO RELEVANT LOCAL
STANDARDS TO PREVENT SKIN CONTACT BASED ON THE RESULTS OF AN EXPOSURE
ASSESSMENT. SELECTION SHOULD BE BASED ON USE FACTORS SUCH AS EXPOSURE
LEVELS, CONCENTRATION OF THE SUBSTANCE OR MIXTURE, FREQUENCY AND DURATION,
PHYSICAL CHALLENGES SUCH AS TEMPERATURE EXTREMES, AND OTHER USE CONDITIONS.
CONSULT WITH YOUR GLOVE AND/OR PROTECTIVE CLOTHING MANUFACTURER FOR
SELECTION OF APPROPRIATE COMPATIBLE GLOVES/PROTECTIVE CLOTHING.
NOTE:
NITRILE GLOVES MAY BE WORN OVER POLYMER LAMINATE GLOVES TO IMPROVE
DEXTERITY.
GLOVES MADE FROM THE FOLLOWING MATERIAL(S) ARE RECOMMENDED:
POLYMER LAMINATE
RESPIRATORY PROTECTION:
AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF A RESPIRATOR IS REQUIRED.
IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS PART OF A FULL RESPIRATORY
PROTECTION PROGRAM. BASED ON THE RESULTS OF THE EXPOSURE ASSESSMENT, SELECT
FROM THE FOLLOWING RESPIRATOR TYPE(S) TO REDUCE INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
ORGANIC VAPORS AND PARTICULATES
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT
WITH YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: LIQUID
SPECIFIC PHYSICAL FORM: PASTE
ODOR, COLOR, GRADE: GRAY, VERY SLIGHT ODOR.
ODOR THRESHOLD: NO DATA AVAILABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: >=260 DEG. C
FLASH POINT: 480 DEG. F [TEST METHOD:CLOSED CUP]
EVAPORATION RATE: NO DATA AVAILABLE
FLAMMABILITY (SOLID, GAS): NOT APPLICABLE
FLAMMABLE LIMITS(LEL): NO DATA AVAILABLE
FLAMMABLE LIMITS(UEL): NO DATA AVAILABLE
VAPOR PRESSURE: NO DATA AVAILABLE
VAPOR DENSITY: NO DATA AVAILABLE
DENSITY: 1.1 G/ML
SPECIFIC GRAVITY: 1.1 [REF STD:WATER=1]
SOLUBILITY IN WATER: NIL
SOLUBILITY- NON-WATER: NO DATA AVAILABLE
PARTITION COEFFICIENT:
N-OCTANOL/ WATER: NO DATA AVAILABLE
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
DECOMPOSITION TEMPERATURE: NO DATA AVAILABLE
VISCOSITY: 30,000 - 70,000 CENTIPOISE [@ 73.4 DEG. F]
HAZARDOUS AIR POLLUTANTS: 0 % WEIGHT [TEST METHOD:CALCULATED]
MOLECULAR WEIGHT: NO DATA AVAILABLE
VOC LESS H2O & EXEMPT SOLVENTS:
0 G/L [TEST METHOD:CALCULATED SCAQMD RULE 443.1]
[DETAILS:WHEN USED AS INTENDED WITH PART B]
VOC LESS H2O & EXEMPT SOLVENTS:
0 G/L [TEST METHOD:CALCULATED SCAQMD RULE 443.1]
[DETAILS:AS SUPPLIED]
VOC LESS H2O & EXEMPT SOLVENTS:
0 % [TEST METHOD:CALCULATED SCAQMD RULE 443.1]
[DETAILS:WHEN USED AS INTENDED WITH PART B]
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL MAY BE REACTIVE WITH CERTAIN AGENTS UNDER CERTAIN
CONDITIONS - SEE THE REMAINING HEADINGS IN THIS SECTION.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID:
AVOID CURING LARGE QUANTITIES OF MATERIAL TO PREVENT A PREMATURE REACTION
(EXOTHERM) WITH PRODUCTION OF INTENSE HEAT AND SMOKE.
10.5. INCOMPATIBLE MATERIALS:
STRONG OXIDIZING AGENTS
STRONG ACIDS
STRONG BASES
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR
THE SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT
BELOW THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL
MAY PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
RESPIRATORY TRACT IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL DISCHARGE, HEADACHE,
HOARSENESS, AND NOSE AND THROAT PAIN.
SKIN CONTACT:
SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE LOCALIZED REDNESS, SWELLING, ITCHING, DRYNESS,
CRACKING, BLISTERING, AND PAIN.
ALLERGIC SKIN REACTION (NON-PHOTO INDUCED):
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, BLISTERING, AND ITCHING.
EYE CONTACT:
SEVERE EYE IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE SIGNIFICANT REDNESS, SWELLING, PAIN, TEARING,
CLOUDY APPEARANCE OF THE CORNEA, AND IMPAIRED VISION.
INGESTION:
MAY BE HARMFUL IF SWALLOWED.
GASTROINTESTINAL IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABDOMINAL PAIN, STOMACH UPSET, NAUSEA, VOMITING
AND DIARRHEA.
CARCINOGENICITY:
INGREDIENT CAS NO. CLASS DESCRIPTION REGULATION
CARBON BLACK 1333-86-4 GRP. 2B: POSSIBLE INTERNATIONAL AGENCY FOR
HUMAN CARC. RESEARCH ON CANCER
ADDITIONAL INFORMATION:
PERSONS PREVIOUSLY SENSITIZED TO AMINES MAY DEVELOP A CROSS-SENSITIZATION
REACTION TO CERTAIN OTHER AMINES.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT DERMAL NO DATA AVAILABLE;
CALCULATED ATE
>5,000 MG/KG
OVERALL PRODUCT INGESTION NO DATA AVAILABLE;
CALCULATED ATE
2,000 - 5,000 MG/KG
MERCAPTAN POLYMER (NJTS DERMAL RABBIT LD50 > 10,200 MG/KG
REG. NO. 04499600-6776)
MERCAPTAN POLYMER (NJTS INGESTION RAT LD50 2,600 MG/KG
REG. NO. 04499600-6776)
POLYAMIDE RESIN DERMAL RAT LD50 > 2,000 MG/KG
POLYAMIDE RESIN INGESTION RAT LD50 > 2,000 MG/KG
HYDROGENATED TERPHENYL DERMAL RABBIT LD50 6,800 MG/KG
HYDROGENATED TERPHENYL INHALATION- RAT LC50 > 11.1 MG/L
DUST/MIST
(4 HOURS)
HYDROGENATED TERPHENYL INGESTION RAT LD50 > 10,000 MG/KG
2,4,6-TRIS[(DIMETHYLAMINO) DERMAL RAT LD50 1,280 MG/KG
METHYL]PHENOL
2,4,6-TRIS[(DIMETHYLAMINO) INGESTION RAT LD50 1,000 MG/KG
METHYL]PHENOL
TRIETHYLENETETRAMINE DERMAL RABBIT LD50 550 MG/KG
TRIETHYLENETETRAMINE INGESTION RAT LD50 2,500 MG/KG
CARBON BLACK DERMAL RABBIT LD50 > 3,000 MG/KG
CARBON BLACK INGESTION RAT LD50 > 8,000 MG/KG
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
MERCAPTAN POLYMER (NJTS REG. NO. RABBIT NO SIGNIFICANT
04499600-6776) IRRITATION
POLYAMIDE RESIN SIMILAR IRRITANT
COMPOUNDS
HYDROGENATED TERPHENYL RABBIT NO SIGNIFICANT
IRRITATION
2,4,6-TRIS[(DIMETHYLAMINO) RABBIT CORROSIVE
METHYL]PHENOL
TRIETHYLENETETRAMINE RABBIT CORROSIVE
CARBON BLACK RABBIT NO SIGNIFICANT
IRRITATION
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
MERCAPTAN POLYMER (NJTS REG. NO. RABBIT MILD IRRITANT
04499600-6776)
POLYAMIDE RESIN SIMILAR CORROSIVE
COMPOUNDS
HYDROGENATED TERPHENYL RABBIT NO SIGNIFICANT
IRRITATION
2,4,6-TRIS[(DIMETHYLAMINO) RABBIT CORROSIVE
METHYL]PHENOL
TRIETHYLENETETRAMINE RABBIT CORROSIVE
CARBON BLACK RABBIT NO SIGNIFICANT
IRRITATION
SKIN SENSITIZATION:
NAME SPECIES VALUE
MERCAPTAN POLYMER (NJTS REG. NO. MOUSE SENSITIZING
04499600-6776)
POLYAMIDE RESIN MOUSE SENSITIZING
HYDROGENATED TERPHENYL HUMAN NOT CLASSIFIED
2,4,6-TRIS[(DIMETHYLAMINO) GUINEA PIG NOT CLASSIFIED
METHYL]PHENOL
TRIETHYLENETETRAMINE GUINEA PIG SENSITIZING
RESPIRATORY SENSITIZATION:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
MERCAPTAN POLYMER (NJTS IN VITRO NOT MUTAGENIC
REG. NO. 04499600-6776)
HYDROGENATED TERPHENYL IN VIVO NOT MUTAGENIC
2,4,6-TRIS[(DIMETHYLAMINO) IN VITRO NOT MUTAGENIC
METHYL]PHENOL
CARBON BLACK IN VITRO NOT MUTAGENIC
CARBON BLACK IN VIVO SOME POSITIVE DATA EXIST, BUT
THE DATA ARE NOT SUFFICIENT
FOR CLASSIFICATION
CARCINOGENICITY:
NAME ROUTE SPECIES VALUE
CARBON BLACK DERMAL MOUSE NOT CARCINOGENIC
CARBON BLACK INGESTION MOUSE NOT CARCINOGENIC
CARBON BLACK INHALATION RAT CARCINOGENIC
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
NAME ROUTE VALUE SPECIES
HYDROGENATED INGESTION NOT CLASSIFIED FOR FEMALE RAT
TERPHENYL REPRODUCTION
HYDROGENATED INGESTION NOT CLASSIFIED FOR MALE RAT
TERPHENYL REPRODUCTION
HYDROGENATED INGESTION NOT CLASSIFIED FOR DEVELOPMENT RAT
TERPHENYL
NAME TEST RESULT EXPOSURE DURATION
HYDROGENATED TERPHENYL NOAEL 81 MG/KG/DAY 2 GENERATION
HYDROGENATED TERPHENYL NOAEL 62 MG/KG/DAY 2 GENERATION
HYDROGENATED TERPHENYL NOAEL 500 MG/KG/DAY 2 GENERATION
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
POLYAMIDE RESIN INHALATION RESPIRATORY SOME POSITIVE
IRRITATION DATA EXIST,
BUT THE DATA
ARE NOT
SUFFICIENT FOR
CLASSIFICATION
2,4,6- INHALATION RESPIRATORY SOME POSITIVE
TRIS[(DIMETHYLAMINO)METH IRRITATION DATA EXIST,
YL]PHENOL BUT THE DATA
ARE NOT
SUFFICIENT FOR
CLASSIFICATION
NAME SPECIES TEST RESULT EXPOSURE
DURATION
POLYAMIDE RESIN SIMILAR NOAEL NOT
HEALTH AVAILABLE
HAZARDS
2,4,6- NOAEL NOT
TRIS[(DIMETHYLAMINO)METH AVAILABLE
YL]PHENOL
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
MERCAPTAN POLYMER (NJTS INGESTION HEMATOPOIETIC SOME POSITIVE
REG. NO. 04499600-6776) SYSTEM DATA EXIST,
BUT THE DATA
ARE NOT
SUFFICIENT FOR
CLASSIFICATION
MERCAPTAN POLYMER (NJTS INGESTION LIVER SOME POSITIVE
REG. NO. 04499600-6776) DATA EXIST,
BUT THE DATA
ARE NOT
SUFFICIENT FOR
CLASSIFICATION
MERCAPTAN POLYMER (NJTS INGESTION ENDOCRINE NOT CLASSIFIED
REG. NO. 04499600-6776) SYSTEM |
HEART | SKIN |
IMMUNE SYSTEM |
NERVOUS
SYSTEM | EYES |
KIDNEY AND/OR
BLADDER |
RESPIRATORY
SYSTEM |
VASCULAR
SYSTEM
HYDROGENATED TERPHENYL INHALATION LIVER NOT CLASSIFIED
HYDROGENATED TERPHENYL INGESTION ENDOCRINE NOT CLASSIFIED
SYSTEM |
BLOOD |
LIVER | KIDNEY
AND/OR BLADDER
2,4,6- DERMAL SKIN | LIVER | NOT CLASSIFIED
TRIS[(DIMETHYLAMINO)METH NERVOUS
YL]PHENOL SYSTEM |
AUDITORY
SYSTEM |
HEMATOPOIETIC
SYSTEM | EYES
CARBON BLACK INHALATION PNEUMOCONIOSIS NOT CLASSIFIED
NAME SPECIES TEST RESULT EXPOSURE
DURATION
MERCAPTAN POLYMER (NJTS RAT NOAEL 75 90 DAYS
REG. NO. 04499600-6776) MG/KG/DAY
MERCAPTAN POLYMER (NJTS RAT NOAEL 250 90 DAYS
REG. NO. 04499600-6776) MG/KG/DAY
MERCAPTAN POLYMER (NJTS RAT NOAEL 1,000 90 DAYS
REG. NO. 04499600-6776) MG/KG/DAY
HYDROGENATED TERPHENYL RAT NOAEL 0.5 MG/L 90 DAYS
HYDROGENATED TERPHENYL RAT NOAEL 144 14 WEEKS
MG/KG/DAY
2,4,6- RAT NOAEL 125 28 DAYS
TRIS[(DIMETHYLAMINO)METH MG/KG/DAY
YL]PHENOL
CARBON BLACK HUMAN NOAEL NOT OCCUPATIONAL
AVAILABLE EXPOSURE
ASPIRATION HAZARD:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN THE SECTION 1 OF
THIS SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN THE SECTION 1 OF
THIS SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL
AND/OR ITS COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN THE SECTION 1 OF
THIS SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL
AND/OR ITS COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/ CONTAINER IN ACCORDANCE WITH THE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
DISPOSE OF COMPLETELY CURED (OR POLYMERIZED) MATERIAL IN A PERMITTED
INDUSTRIAL WASTE FACILITY. AS A DISPOSAL ALTERNATIVE, INCINERATE UNCURED
PRODUCT IN A PERMITTED WASTE INCINERATION FACILITY. PROPER DESTRUCTION
MAY REQUIRE THE USE OF ADDITIONAL FUEL DURING INCINERATION PROCESSES.
EMPTY DRUMS/BARRELS/CONTAINERS USED FOR TRANSPORTING AND HANDLING HAZARDOUS
CHEMICALS (CHEMICAL SUBSTANCES/MIXTURES/PREPARATIONS CLASSIFIED AS
HAZARDOUS AS PER APPLICABLE REGULATIONS) SHALL BE CONSIDERED, STORED,
TREATED & DISPOSED OF AS HAZARDOUS WASTES UNLESS OTHERWISE DEFINED BY
APPLICABLE WASTE REGULATIONS. CONSULT WITH THE RESPECTIVE REGULATING
AUTHORITIES TO DETERMINE THE AVAILABLE TREATMENT AND DISPOSAL FACILITIES.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
| SECTION 14: TRANSPORT INFORMATION | |
FOR TRANSPORT INFORMATION, PLEASE VISIT HTTP://3M.COM/TRANSPORTINFO
OR CALL 1-800-364-3577 OR 651-737-6501.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
EPCRA 311/312 HAZARD CLASSIFICATIONS:
PHYSICAL HAZARDS: NOT APPLICABLE
HEALTH HAZARDS:
RESPIRATORY OR SKIN SENSITIZATION
SERIOUS EYE DAMAGE OR EYE IRRITATION
SKIN CORROSION OR IRRITATION
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
15.3. CHEMICAL INVENTORIES:
THE COMPONENTS OF THIS PRODUCT ARE IN COMPLIANCE WITH THE CHEMICAL
NOTIFICATION REQUIREMENTS OF TSCA.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 2
FLAMMABILITY 1
INSTABILITY 1
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED
FOR USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS
OF FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY
BASED ON THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT
ALSO INCLUDE THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS
THAT ARE KNOWN TO BE GENERATED IN SIGNIFICANT QUANTITIES.
DOCUMENT GROUP: 22-1043-3
VERSION NUMBER: 7.00
ISSUE DATE: 12/11/17
SUPERCEDES DATE: 10/28/16
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE3MPRODUCT IS FIT FOR
A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND APPLICATION OF
A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S KNOWLEDGE AND
CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M PRODUCT TO DETERMINE
WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD
OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP110 GRAY, PART B OR EPOXY ADHESIVE
110 GRAY, PART B
05/21/18
3M
SAFETY DATA SHEET
COPYRIGHT,2018,3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR THE
PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 11-3320-6
VERSION NUMBER: 18.00
ISSUE DATE: 05/21/18
SUPERCEDES DATE: 12/11/17
| SECTION 1: IDENTIFICATION | |
1.1. PRODUCT IDENTIFIER:
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP110 GRAY, PART B OR EPOXY
ADHESIVE 110 GRAY, PART B
PRODUCT IDENTIFICATION NUMBERS: 62-3533-8531-3
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE: STRUCTURAL ADHESIVE
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: INDUSTRIAL ADHESIVES AND TAPES DIVISION
ADDRESS:
3M CENTER,
ST. PAUL
MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
SERIOUS EYE DAMAGE/IRRITATION: CATEGORY 2B.
SKIN SENSITIZER: CATEGORY 1.
2.2. LABEL ELEMENTS:
SIGNAL WORD: WARNING
SYMBOLS: EXCLAMATION MARK
PICTOGRAMS: EXCLAMATION MARK
HAZARD STATEMENTS:
CAUSES EYE IRRITATION.
MAY CAUSE AN ALLERGIC SKIN REACTION.
PRECAUTIONARY STATEMENTS:
PREVENTION:
AVOID BREATHING DUST/FUME/GAS/MIST/VAPORS/SPRAY.
WEAR PROTECTIVE GLOVES.
WASH THOROUGHLY AFTER HANDLING.
CONTAMINATED WORK CLOTHING MUST NOT BE ALLOWED OUT OF THE WORKPLACE.
RESPONSE:
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES,
IF PRESENT AND EASY TO DO. CONTINUE RINSING.
IF EYE IRRITATION PERSISTS: GET MEDICAL ADVICE/ATTENTION.
IF ON SKIN: WASH WITH PLENTY OF SOAP AND WATER.
IF SKIN IRRITATION OR RASH OCCURS: GET MEDICAL ADVICE/ATTENTION.
WASH CONTAMINATED CLOTHING BEFORE REUSE.
DISPOSAL:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH APPLICABLE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
1% OF THE MIXTURE CONSISTS OF INGREDIENTS OF UNKNOWN ACUTE ORAL TOXICITY.
1% OF THE MIXTURE CONSISTS OF INGREDIENTS OF UNKNOWN ACUTE DERMAL TOXICITY.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
EPOXY RESIN 25068-38-6 60 - 90 TRADE SECRET *
METHACRYLATE/BUTADIENE/STYRENE 25053-09-2 10 - 30 TRADE SECRET *
POLYMER
HYDROGENATED TERPHENYL 61788-32-7 5 - 10 TRADE SECRET *
HYDROGENATED POLYPHENYLS 68956-74-1 <= 1.5 TRADE SECRET *
TITANIUM DIOXIDE 13463-67-7 0.1 - 1 TRADE SECRET *
*THE SPECIFIC CHEMICAL IDENTITY AND/OR EXACT PERCENTAGE (CONCENTRATION) OF
THIS COMPOSITION HAS BEEN WITHHELD AS A TRADE SECRET.
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
IMMEDIATELY WASH WITH SOAP AND WATER. REMOVE CONTAMINATED CLOTHING AND
WASH BEFORE REUSE. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL ATTENTION.
EYE CONTACT:
FLUSH WITH LARGE AMOUNTS OF WATER. REMOVE CONTACT LENSES IF EASY TO DO.
CONTINUE RINSING. IF SIGNS/SYMPTOMS PERSIST, GET MEDICAL ATTENTION.
IF SWALLOWED:
RINSE MOUTH. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED:
NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
IN CASE OF FIRE:
USE A FIRE FIGHTING AGENT SUITABLE FOR ORDINARY COMBUSTIBLE MATERIAL SUCH
AS WATER OR FOAM TO EXTINGUISH.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
NONE INHERENT IN THIS PRODUCT.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
ALDEHYDES DURING COMBUSTION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
NO SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS ARE ANTICIPATED.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
EVACUATE AREA. VENTILATE THE AREA WITH FRESH AIR. FOR LARGE SPILL, OR
SPILLS IN CONFINED SPACES, PROVIDE MECHANICAL VENTILATION TO DISPERSE
OR EXHAUST VAPORS, IN ACCORDANCE WITH GOOD INDUSTRIAL HYGIENE PRACTICE.
REFER TO OTHER SECTIONS OF THIS SDS FOR INFORMATION REGARDING PHYSICAL
AND HEALTH HAZARDS, RESPIRATORY PROTECTION, VENTILATION, AND PERSONAL
PROTECTIVE EQUIPMENT.
6.2. ENVIRONMENTAL PRECAUTIONS:
AVOID RELEASE TO THE ENVIRONMENT. FOR LARGER SPILLS, COVER DRAINS AND
BUILD DIKES TO PREVENT ENTRY INTO SEWER SYSTEMS OR BODIES OF WATER.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP:
WORKING FROM AROUND THE EDGES OF THE SPILL INWARD, COVER WITH BENTONITE,
VERMICULITE, OR COMMERCIALLY AVAILABLE INORGANIC ABSORBENT MATERIAL. MIX
IN SUFFICIENT ABSORBENT UNTIL IT APPEARS DRY. REMEMBER, ADDING AN
ABSORBENT MATERIAL DOES NOT REMOVE A PHYSICAL, HEALTH, OR ENVIRONMENTAL
HAZARD. COLLECT AS MUCH OF THE SPILLED MATERIAL AS POSSIBLE. PLACE IN A
CLOSED CONTAINER APPROVED FOR TRANSPORTATION BY APPROPRIATE AUTHORITIES.
CLEAN UP RESIDUE WITH AN APPROPRIATE SOLVENT SELECTED BY A QUALIFIED AND
AUTHORIZED PERSON. VENTILATE THE AREA WITH FRESH AIR. READ AND FOLLOW
SAFETY PRECAUTIONS ON THE SOLVENT LABEL AND SDS. SEAL THE CONTAINER.
DISPOSE OF COLLECTED MATERIAL AS SOON AS POSSIBLE IN ACCORDANCE WITH
APPLICABLE LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
FOR INDUSTRIAL OR PROFESSIONAL USE ONLY. AVOID BREATHING
DUST/FUME/GAS/MIST/VAPORS/SPRAY. DO NOT GET IN EYES, ON SKIN, OR ON
CLOTHING. DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT. WASH
THOROUGHLY AFTER HANDLING. CONTAMINATED WORK CLOTHING SHOULD NOT BE
ALLOWED OUT OF THE WORKPLACE. AVOID RELEASE TO THE ENVIRONMENT. WASH
CONTAMINATED CLOTHING BEFORE REUSE. AVOID CONTACT WITH OXIDIZING AGENTS
(EG. CHLORINE, CHROMIC ACID ETC.)
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
STORE AWAY FROM OXIDIZING AGENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN THE TABLE
BELOW, AN OCCUPATIONAL EXPOSURE LIMIT IS NOT AVAILABLE FOR THE COMPONENT.
INGREDIENT C.A.S. NO. AGENCY LIMIT TYPE ADDITIONAL
COMMENTS
TITANIUM DIOXIDE 13463-67-7 ACGIH TWA:10 MG/M3 A4: NOT
CLASS. AS
HUMAN
CARCIN
TITANIUM DIOXIDE 13463-67-7 OSHA TWA(AS TOTAL
DUST):15 MG/M3
HYDROGENATED 61788-32-7 ACGIH TWA:0.5 PPM
TERPHENYL
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
AIHA: AMERICAN INDUSTRIAL HYGIENE ASSOCIATION
CMRG: CHEMICAL MANUFACTURER'S RECOMMENDED GUIDELINES
OSHA:
UNITED STATES DEPARTMENT OF LABOR - OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION
TWA: TIME-WEIGHTED-AVERAGE
STEL: SHORT TERM EXPOSURE LIMIT
CEIL: CEILING
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO
CONTROL AIRBORNE EXPOSURES TO BELOW RELEVANT EXPOSURE LIMITS AND/OR
CONTROL DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS NOT ADEQUATE,
USE RESPIRATORY PROTECTION EQUIPMENT.
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON THE RESULTS
OF AN EXPOSURE ASSESSMENT. THE FOLLOWING EYE/FACE PROTECTION(S) ARE
RECOMMENDED:
INDIRECT VENTED GOGGLES
SKIN/HAND PROTECTION:
SELECT AND USE GLOVES AND/OR PROTECTIVE CLOTHING APPROVED TO RELEVANT LOCAL
STANDARDS TO PREVENT SKIN CONTACT BASED ON THE RESULTS OF AN EXPOSURE
ASSESSMENT. SELECTION SHOULD BE BASED ON USE FACTORS SUCH AS EXPOSURE
LEVELS, CONCENTRATION OF THE SUBSTANCE OR MIXTURE, FREQUENCY AND DURATION,
PHYSICAL CHALLENGES SUCH AS TEMPERATURE EXTREMES, AND OTHER USE CONDITIONS.
CONSULT WITH YOUR GLOVE AND/OR PROTECTIVE CLOTHING MANUFACTURER FOR
SELECTION OF APPROPRIATE COMPATIBLE GLOVES/PROTECTIVE CLOTHING.
NOTE:
NITRILE GLOVES MAY BE WORN OVER POLYMER LAMINATE GLOVES TO IMPROVE
DEXTERITY.
GLOVES MADE FROM THE FOLLOWING MATERIAL(S) ARE RECOMMENDED:
BUTYL RUBBER
POLYMER LAMINATE
RESPIRATORY PROTECTION:
UNDER NORMAL USE CONDITIONS, AIRBORNE EXPOSURES ARE NOT EXPECTED TO BE
SIGNIFICANT ENOUGH TO REQUIRE RESPIRATORY PROTECTION.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: LIQUID
SPECIFIC PHYSICAL FORM: PASTE
ODOR, COLOR, GRADE: WHITE, VERY SLIGHT ODOR.
ODOR THRESHOLD: NO DATA AVAILABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: >=260 DEG. C
FLASH POINT: >=480 DEG. F [TEST METHOD:CLOSED CUP]
EVAPORATION RATE: NOT APPLICABLE
FLAMMABILITY (SOLID, GAS): NOT APPLICABLE
FLAMMABLE LIMITS(LEL): NOT APPLICABLE
FLAMMABLE LIMITS(UEL): NOT APPLICABLE
VAPOR PRESSURE: NOT APPLICABLE
VAPOR DENSITY: NOT APPLICABLE
DENSITY: 1.14 G/ML
SPECIFIC GRAVITY: 1.14 [REF STD:WATER=1]
SOLUBILITY IN WATER: NIL
SOLUBILITY- NON-WATER: NO DATA AVAILABLE
PARTITION COEFFICIENT:
N-OCTANOL/ WATER: NO DATA AVAILABLE
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
DECOMPOSITION TEMPERATURE: NO DATA AVAILABLE
VISCOSITY: 45,000 - 65,000 CENTIPOISE [@ 73.4 DEG. F]
HAZARDOUS AIR POLLUTANTS: 0 % WEIGHT [TEST METHOD:CALCULATED]
MOLECULAR WEIGHT: NO DATA AVAILABLE
VOC LESS H2O & EXEMPT SOLVENTS:
0 G/L [TEST METHOD: CALCULATED SCAQMD RULE 443.1]
[DETAILS: WHEN USED AS INTENDED WITH PART A]
VOC LESS H2O & EXEMPT SOLVENTS:
0 G/L [TEST METHOD: CALCULATED SCAQMD RULE 443.1]
[DETAILS: AS SUPPLIED]
VOC LESS H2O & EXEMPT SOLVENTS:
0 % [TEST METHOD: CALCULATED SCAQMD RULE 443.1]
[DETAILS: WHEN USED AS INTENDED WITH PART A]
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL MAY BE REACTIVE WITH CERTAIN AGENTS UNDER CERTAIN
CONDITIONS - SEE THE REMAINING HEADINGS IN THIS SECTION.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID:
HEAT IS GENERATED DURING CURE. DO NOT CURE A MASS LARGER THAN 50 GRAMS
IN A CONFINED SPACE TO PREVENT A PREMATURE EXOTHERMIC REACTION WITH
PRODUCTION OF INTENSE HEAT AND SMOKE.
10.5. INCOMPATIBLE MATERIALS: STRONG OXIDIZING AGENTS
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR
THE SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT
BELOW THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL
MAY PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION: NO HEALTH EFFECTS ARE EXPECTED.
SKIN CONTACT:
MILD SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE LOCALIZED REDNESS, SWELLING, ITCHING, AND
DRYNESS.
ALLERGIC SKIN REACTION (NON-PHOTO INDUCED):
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, BLISTERING, AND ITCHING.
EYE CONTACT:
MODERATE EYE IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND
BLURRED OR HAZY VISION.
INGESTION:
GASTROINTESTINAL IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABDOMINAL PAIN, STOMACH UPSET, NAUSEA,
VOMITING AND DIARRHEA.
CARCINOGENICITY:
INGREDIENT CAS NO. CLASS DESCRIPTION REGULATION
TITANIUM 13463-67-7 GRP. 2B: POSSIBLE INTERNATIONAL AGENCY FOR
DIOXIDE HUMAN CARC. RESEARCH ON CANCER
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE
NOT SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT DERMAL NO DATA AVAILABLE;
CALCULATED ATE
>5,000 MG/KG
OVERALL PRODUCT INGESTION NO DATA AVAILABLE;
CALCULATED ATE
>5,000 MG/KG
EPOXY RESIN DERMAL RAT LD50 > 1,600 MG/KG
EPOXY RESIN INGESTION RAT LD50 > 1,000 MG/KG
METHACRYLATE/BUTADIENE/ DERMAL RABBIT LD50 > 5,000 MG/KG
STYRENE POLYMER
METHACRYLATE/BUTADIENE/ INGESTION RAT LD50 > 5,000 MG/KG
STYRENE POLYMER
HYDROGENATED TERPHENYL DERMAL RABBIT LD50 6,800 MG/KG
HYDROGENATED TERPHENYL INHALATION- RAT LC50 > 11.1 MG/L
DUST/MIST
(4 HOURS)
HYDROGENATED TERPHENYL INGESTION RAT LD50 > 10,000 MG/KG
TITANIUM DIOXIDE DERMAL RABBIT LD50 > 10,000 MG/KG
TITANIUM DIOXIDE INHALATION- RAT LC50 > 6.82 MG/L
DUST/MIST
(4 HOURS)
TITANIUM DIOXIDE INGESTION RAT LD50 > 10,000 MG/KG
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
EPOXY RESIN RABBIT MILD IRRITANT
METHACRYLATE/BUTADIENE/STYRENE PROFESSIONAL MINIMAL
POLYMER JUDGEMENT IRRITATION
HYDROGENATED TERPHENYL RABBIT NO SIGNIFICANT
IRRITATION
TITANIUM DIOXIDE RABBIT NO SIGNIFICANT
IRRITATION
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
EPOXY RESIN RABBIT MODERATE IRRITANT
METHACRYLATE/BUTADIENE/STYRENE PROFESSIONAL MILD IRRITANT
POLYMER JUDGEMENT
HYDROGENATED TERPHENYL RABBIT NO SIGNIFICANT
IRRITATION
TITANIUM DIOXIDE RABBIT NO SIGNIFICANT
IRRITATION
SKIN SENSITIZATION:
NAME SPECIES VALUE
EPOXY RESIN HUMAN AND ANIMAL SENSITIZING
HYDROGENATED TERPHENYL HUMAN NOT CLASSIFIED
TITANIUM DIOXIDE HUMAN AND ANIMAL NOT CLASSIFIED
RESPIRATORY SENSITIZATION:
NAME SPECIES VALUE
EPOXY RESIN HUMAN NOT CLASSIFIED
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
EPOXY RESIN IN VIVO NOT MUTAGENIC
EPOXY RESIN IN VITRO SOME POSITIVE DATA EXIST, BUT
THE DATA ARE NOT SUFFICIENT
FOR CLASSIFICATION
HYDROGENATED TERPHENYL IN VIVO NOT MUTAGENIC
TITANIUM DIOXIDE IN VITRO NOT MUTAGENIC
TITANIUM DIOXIDE IN VIVO NOT MUTAGENIC
CARCINOGENICITY:
NAME ROUTE SPECIES VALUE
EPOXY RESIN DERMAL MOUSE SOME POSITIVE DATA EXIST, BUT
THE DATA ARE NOT SUFFICIENT
FOR CLASSIFICATION
TITANIUM DIOXIDE INGESTION MULTIPLE NOT CARCINOGENIC
ANIMAL
SPECIES
TITANIUM DIOXIDE INHALATION RAT CARCINOGENIC
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
NAME ROUTE VALUE SPECIES
EPOXY RESIN INGESTION NOT CLASSIFIED FOR FEMALE RAT
REPRODUCTION
EPOXY RESIN INGESTION NOT CLASSIFIED FOR MALE RAT
REPRODUCTION
EPOXY RESIN DERMAL NOT CLASSIFIED FOR DEVELOPMENT RABBIT
EPOXY RESIN INGESTION NOT CLASSIFIED FOR DEVELOPMENT RAT
HYDROGENATED INGESTION NOT CLASSIFIED FOR FEMALE RAT
TERPHENYL REPRODUCTION
HYDROGENATED INGESTION NOT CLASSIFIED FOR MALE RAT
TERPHENYL REPRODUCTION
HYDROGENATED INGESTION NOT CLASSIFIED FOR DEVELOPMENT RAT
TERPHENYL
NAME TEST RESULT EXPOSURE DURATION
EPOXY RESIN NOAEL 750 MG/KG/DAY 2 GENERATION
EPOXY RESIN NOAEL 750 MG/KG/DAY 2 GENERATION
EPOXY RESIN NOAEL 300 MG/KG/DAY DURING ORGANOGENESIS
EPOXY RESIN NOAEL 750 MG/KG/DAY 2 GENERATION
HYDROGENATED TERPHENYL NOAEL 81 MG/KG/DAY 2 GENERATION
HYDROGENATED TERPHENYL NOAEL 62 MG/KG/DAY 2 GENERATION
HYDROGENATED TERPHENYL NOAEL 500 MG/KG/DAY 2 GENERATION
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
EPOXY RESIN DERMAL LIVER NOT CLASSIFIED
EPOXY RESIN DERMAL NERVOUS SYSTEM NOT CLASSIFIED
EPOXY RESIN INGESTION AUDITORY NOT CLASSIFIED
SYSTEM |
HEART |
ENDOCRINE
SYSTEM |
HEMATOPOIETIC
SYSTEM |
LIVER | EYES |
KIDNEY AND/OR
BLADDER
HYDROGENATED TERPHENYL INHALATION LIVER NOT CLASSIFIED
HYDROGENATED TERPHENYL INGESTION ENDOCRINE NOT CLASSIFIED
SYSTEM |
BLOOD |
LIVER |
KIDNEY AND/OR
BLADDER
TITANIUM DIOXIDE INHALATION RESPIRATORY SOME POSITIVE
SYSTEM DATA EXIST,
BUT THE DATA
ARE NOT
SUFFICIENT FOR
CLASSIFICATION
TITANIUM DIOXIDE INHALATION PULMONARY NOT CLASSIFIED
FIBROSIS
NAME SPECIES TEST RESULT EXPOSURE
DURATION
EPOXY RESIN RAT NOAEL 1,000 2 YEARS
MG/KG/DAY
EPOXY RESIN RAT NOAEL 1,000 13 WEEKS
MG/KG/DAY
EPOXY RESIN RAT NOAEL 1,000 28 DAYS
MG/KG/DAY
HYDROGENATED TERPHENYL RAT NOAEL 0.5 90 DAYS
MG/L
HYDROGENATED TERPHENYL RAT NOAEL 144 14 WEEKS
MG/KG/DAY
TITANIUM DIOXIDE RAT LOAEL 0.01 2 YEARS
MG/L
TITANIUM DIOXIDE HUMAN NOAEL NOT OCCUPATIONAL
AVAILABLE EXPOSURE
ASPIRATION HAZARD:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN THE SECTION 1 OF THIS
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN THE SECTION 1 OF
THIS SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL
AND/OR ITS COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN THE SECTION 1 OF
THIS SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL
AND/OR ITS COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/ CONTAINER IN ACCORDANCE WITH THE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
DISPOSE OF COMPLETELY CURED (OR POLYMERIZED) MATERIAL IN A PERMITTED
INDUSTRIAL WASTE FACILITY. AS A DISPOSAL ALTERNATIVE, INCINERATE UNCURED
PRODUCT IN A PERMITTED WASTE INCINERATION FACILITY. PROPER DESTRUCTION MAY
REQUIRE THE USE OF ADDITIONAL FUEL DURING INCINERATION PROCESSES.
COMBUSTION PRODUCTS WILL INCLUDE HALOGEN ACID (HCL/HF/HBR). FACILITY MUST
BE CAPABLE OF HANDLING HALOGENATED MATERIALS. EMPTY
DRUMS/BARRELS/CONTAINERS USED FOR TRANSPORTING AND HANDLING HAZARDOUS
CHEMICALS (CHEMICAL SUBSTANCES/MIXTURES/PREPARATIONS CLASSIFIED AS
HAZARDOUS AS PER APPLICABLE REGULATIONS) SHALL BE CONSIDERED, STORED,
TREATED & DISPOSED OF AS HAZARDOUS WASTES UNLESS OTHERWISE DEFINED BY
APPLICABLE WASTE REGULATIONS. CONSULT WITH THE RESPECTIVE REGULATING
AUTHORITIES TO DETERMINE THE AVAILABLE TREATMENT AND DISPOSAL FACILITIES.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
| SECTION 14: TRANSPORT INFORMATION | |
FOR TRANSPORT INFORMATION, PLEASE VISIT HTTP://3M.COM/TRANSPORTINFO
OR CALL 1-800-364-3577 OR 651-737-6501.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
EPCRA 311/312 HAZARD CLASSIFICATIONS:
PHYSICAL HAZARDS: NOT APPLICABLE
HEALTH HAZARDS:
SERIOUS EYE DAMAGE OR EYE IRRITATION
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
CALIFORNIA PROPOSITION 65:
INGREDIENT C.A.S. NO. LISTING
4,4'-ISOPROPYLIDENEDIPHENOL 80-05-7 FEMALE REPRODUCTIVE TOXIN
STYRENE MONOMER 100-42-5 CARCINOGEN
TITANIUM DIOXIDE 13463-67-7 CARCINOGEN
15.3. CHEMICAL INVENTORIES:
THE COMPONENTS OF THIS PRODUCT ARE IN COMPLIANCE WITH THE CHEMICAL
NOTIFICATION REQUIREMENTS OF TSCA. ALL REQUIRED COMPONENTS OF THIS
PRODUCT ARE LISTED ON THE ACTIVE PORTION OF THE TSCA INVENTORY.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 2
FLAMMABILITY 1
INSTABILITY 0
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED
FOR USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS
OF FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY
BASED ON THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT
ALSO INCLUDE THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS
THAT ARE KNOWN TO BE GENERATED IN SIGNIFICANT QUANTITIES.
DOCUMENT GROUP: 11-3320-6
VERSION NUMBER: 18.00
ISSUE DATE: 05/21/18
SUPERCEDES DATE: 12/11/17
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE3MPRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL,IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M PRODUCT
TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND SUITABLE FOR
USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M