| Common Name: | SCOTCH-WELD EPOXY ADHESIVE DP190 GRAY |
| Manufacturer: | 3M |
| SDS Revision Date: | 5/9/2019 |
| SDS Format: | GHS-US |
| Item Number(s): | 2JBK8, 2JCE2, 489J94 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP190 GRAY
05/09/19
3M
SAFETY DATA SHEET
COPYRIGHT, 2019, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR
THE PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 11-3179-6
VERSION NUMBER: 17.02
ISSUE DATE: 05/09/19
SUPERCEDES DATE: 05/09/18
PRODUCT IDENTIFIER: 3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP190 GRAY
ID NUMBER(S):
62-3553-1430-3, 62-3553-1432-9, 62-3553-1435-2, 62-3553-1436-0,
62-3553-1437-8, 62-3553-1438-6, 62-3553-1439-4, 62-35533530-8,
62-3553-3830-2
7100077115, 7010366135, 7100076722, 7000121314, 7010366136, 7010409744,
7010410438
RECOMMENDED USE: STRUCTURAL ADHESIVE
SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: INDUSTRIAL ADHESIVES AND TAPES DIVISION
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
EMERGENCY TELEPHONE NUMBER: 1-800-364-3577 OR (651) 737-6501 (24 HOURS)
THIS PRODUCT IS A KIT OR A MULTIPART PRODUCT WHICH CONSISTS OF MULTIPLE,
INDEPENDENTLY PACKAGED COMPONENTS. A SAFETY DATA SHEET (SDS), ARTICLE
INFORMATION SHEET (AIS), OR ARTICLE INFORMATION LETTER (AIL) FOR EACH OF
THESE COMPONENTS IS INCLUDED. PLEASE DO NOT SEPARATE THE COMPONENT
DOCUMENTS FROM THIS COVER SHEET.
THE DOCUMENT NUMBERS FOR COMPONENTS OF THIS PRODUCT ARE:
10-3349-7, 10-3348-9
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY.
IN ADDITION, INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT
AS THE INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP190 GRAY, PART B
05/21/18
3M
SAFETY DATA SHEET
COPYRIGHT, 2018, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR
THE PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 10-3348-9
VERSION NUMBER: 33.00
ISSUE DATE: 05/21/18
SUPERCEDES DATE: 04/03/18
| SECTION 1: IDENTIFICATION |  |
1.1. PRODUCT IDENTIFIER:
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP190 GRAY, PART B
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE: STRUCTURAL ADHESIVE
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: INDUSTRIAL ADHESIVES AND TAPES DIVISION
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
SERIOUS EYE DAMAGE/IRRITATION: CATEGORY 2B.
SKIN SENSITIZER: CATEGORY 1.
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE): CATEGORY 1.
2.2. LABEL ELEMENTS:
SIGNAL WORD: DANGER
SYMBOLS:
EXCLAMATION MARK
HEALTH HAZARD
PICTOGRAMS:
EXCLAMATION MARK
HEALTH HAZARD
HAZARD STATEMENTS:
CAUSES EYE IRRITATION.
MAY CAUSE AN ALLERGIC SKIN REACTION.
CAUSES DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE:
RESPIRATORY SYSTEM
PRECAUTIONARY STATEMENTS:
PREVENTION:
DO NOT BREATHE DUST/FUME/GAS/MIST/VAPORS/SPRAY.
WEAR PROTECTIVE GLOVES.
DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT.
WASH THOROUGHLY AFTER HANDLING.
CONTAMINATED WORK CLOTHING MUST NOT BE ALLOWED OUT OF THE WORKPLACE.
RESPONSE:
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES,
IF PRESENT AND EASY TO DO. CONTINUE RINSING.
IF EYE IRRITATION PERSISTS: GET MEDICAL ADVICE/ATTENTION.
IF ON SKIN: WASH WITH PLENTY OF SOAP AND WATER.
IF SKIN IRRITATION OR RASH OCCURS: GET MEDICAL ADVICE/ATTENTION.
WASH CONTAMINATED CLOTHING BEFORE REUSE.
GET MEDICAL ADVICE/ATTENTION IF YOU FEEL UNWELL.
DISPOSAL:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH APPLICABLE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
EPOXY RESIN 25068-38-6 70 - 90 TRADE SECRET*
KAOLIN 1332-58-7 10 - 30 TRADE SECRET*
*THE SPECIFIC CHEMICAL IDENTITY AND/OR EXACT PERCENTAGE (CONCENTRATION)
OF THIS COMPOSITION HAS BEEN WITHHELD AS A TRADE SECRET.
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
IMMEDIATELY WASH WITH SOAP AND WATER. REMOVE CONTAMINATED CLOTHING AND
WASH BEFORE REUSE. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL ATTENTION.
EYE CONTACT:
FLUSH WITH LARGE AMOUNTS OF WATER. REMOVE CONTACT LENSES IF EASY TO DO.
CONTINUE RINSING. IF SIGNS/SYMPTOMS PERSIST, GET MEDICAL ATTENTION.
IF SWALLOWED: RINSE MOUTH. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED: NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
IN CASE OF FIRE:
USE A FIRE FIGHTING AGENT SUITABLE FOR ORDINARY COMBUSTIBLE MATERIAL SUCH
AS WATER OR FOAM TO EXTINGUISH.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
NONE INHERENT IN THIS PRODUCT.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
ALDEHYDES DURING COMBUSTION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
HYDROGEN CHLORIDE DURING COMBUSTION
KETONES DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
WEAR FULL PROTECTIVE CLOTHING, INCLUDING HELMET, SELF-CONTAINED, POSITIVE
PRESSURE OR PRESSURE DEMAND BREATHING APPARATUS, BUNKER COAT AND PANTS,
BANDS AROUND ARMS, WAIST AND LEGS, FACE MASK, AND PROTECTIVE COVERING FOR
EXPOSED AREAS OF THE HEAD.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
EVACUATE AREA. VENTILATE THE AREA WITH FRESH AIR. FOR LARGE SPILL, OR
SPILLS IN CONFINED SPACES, PROVIDE MECHANICAL VENTILATION TO DISPERSE OR
EXHAUST VAPORS, IN ACCORDANCE WITH GOOD INDUSTRIAL HYGIENE PRACTICE. REFER
TO OTHER SECTIONS OF THIS SDS FOR INFORMATION REGARDING PHYSICAL AND HEALTH
HAZARDS, RESPIRATORY PROTECTION, VENTILATION, AND PERSONAL PROTECTIVE
EQUIPMENT.
6.2. ENVIRONMENTAL PRECAUTIONS:
AVOID RELEASE TO THE ENVIRONMENT. FOR LARGER SPILLS, COVER DRAINS AND BUILD
DIKES TO PREVENT ENTRY INTO SEWER SYSTEMS OR BODIES OF WATER.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP:
CONTAIN SPILL. WORKING FROM AROUND THE EDGES OF THE SPILL INWARD, COVER
WITH BENTONITE, VERMICULITE, OR COMMERCIALLY AVAILABLE INORGANIC ABSORBENT
MATERIAL. MIX IN SUFFICIENT ABSORBENT UNTIL IT APPEARS DRY. REMEMBER,
ADDING AN ABSORBENT MATERIAL DOES NOT REMOVE A PHYSICAL, HEALTH, OR
ENVIRONMENTAL HAZARD. COLLECT AS MUCH OF THE SPILLED MATERIAL AS POSSIBLE.
PLACE IN A CLOSED CONTAINER APPROVED FOR TRANSPORTATION BY APPROPRIATE
AUTHORITIES. CLEAN UP RESIDUE WITH AN APPROPRIATE SOLVENT SELECTED BY A
QUALIFIED AND AUTHORIZED PERSON. VENTILATE THE AREA WITH FRESH AIR. READ
AND FOLLOW SAFETY PRECAUTIONS ON THE SOLVENT LABEL AND SDS. SEAL THE
CONTAINER. DISPOSE OF COLLECTED MATERIAL AS SOON AS POSSIBLE IN ACCORDANCE
WITH APPLICABLE LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
FOR INDUSTRIAL OR PROFESSIONAL USE ONLY. DO NOT BREATHE
DUST/FUME/GAS/MIST/VAPORS/SPRAY. DO NOT GET IN EYES, ON SKIN, OR ON
CLOTHING. DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT. WASH
THOROUGHLY AFTER HANDLING. CONTAMINATED WORK CLOTHING SHOULD NOT BE ALLOWED
OUT OF THE WORKPLACE. AVOID RELEASE TO THE ENVIRONMENT. WASH CONTAMINATED
CLOTHING BEFORE REUSE. AVOID CONTACT WITH OXIDIZING AGENTS (EG. CHLORINE,
CHROMIC ACID ETC.)
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
STORE AWAY FROM ACIDS. STORE AWAY FROM OXIDIZING AGENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN THE TABLE
BELOW, AN OCCUPATIONAL EXPOSURE LIMIT IS NOT AVAILABLE FOR THE COMPONENT.
INGREDIENT C.A.S. NO. AGENCY LIMIT TYPE ADDITIONAL
COMMENTS
KAOLIN 1332-58-7 ACGIH TWA (RESPIRABLE A4:
FRACTION): 2 MG/M3 NOT CLASS.
AS HUMAN
CARCIN
KAOLIN, TOTAL DUST 1332-58-7 OSHA TWA(AS TOTAL
DUST): 15 MG/M3
TWA (RESPIRABLE
FRACTION): 5 MG/M3
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
AIHA: AMERICAN INDUSTRIAL HYGIENE ASSOCIATION
CMRG: CHEMICAL MANUFACTURER'S RECOMMENDED GUIDELINES
OSHA:
UNITED STATES DEPARTMENT OF LABOR - OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION
TWA: TIME-WEIGHTED-AVERAGE
STEL: SHORT TERM EXPOSURE LIMIT
CEIL: CEILING
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO
CONTROL AIRBORNE EXPOSURES TO BELOW RELEVANT EXPOSURE LIMITS AND/OR
CONTROL DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS NOT ADEQUATE,
USE RESPIRATORY PROTECTION EQUIPMENT.
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON THE RESULTS
OF AN EXPOSURE ASSESSMENT.
THE FOLLOWING EYE/FACE PROTECTION(S) ARE RECOMMENDED:
INDIRECT VENTED GOGGLES
SKIN/HAND PROTECTION:
SELECT AND USE GLOVES AND/OR PROTECTIVE CLOTHING APPROVED TO RELEVANT LOCAL
STANDARDS TO PREVENT SKIN CONTACT BASED ON THE RESULTS OF AN EXPOSURE
ASSESSMENT. SELECTION SHOULD BE BASED ON USE FACTORS SUCH AS EXPOSURE
LEVELS, CONCENTRATION OF THE SUBSTANCE OR MIXTURE, FREQUENCY AND DURATION,
PHYSICAL CHALLENGES SUCH AS TEMPERATURE EXTREMES, AND OTHER USE CONDITIONS.
CONSULT WITH YOUR GLOVE AND/OR PROTECTIVE CLOTHING MANUFACTURER FOR
SELECTION OF APPROPRIATE COMPATIBLE GLOVES/PROTECTIVE CLOTHING.
NOTE:
NITRILE GLOVES MAY BE WORN OVER POLYMER LAMINATE GLOVES TO IMPROVE
DEXTERITY.
GLOVES MADE FROM THE FOLLOWING MATERIAL(S) ARE RECOMMENDED:
POLYMER LAMINATE
IF THIS PRODUCT IS USED IN A MANNER THAT PRESENTS A HIGHER POTENTIAL FOR
EXPOSURE (EG. SPRAYING, HIGH SPLASH POTENTIAL ETC.), THEN USE OF PROTECTIVE
COVERALLS MAY BE NECESSARY. SELECT AND USE BODY PROTECTION TO PREVENT
CONTACT BASED ON THE RESULTS OF AN EXPOSURE ASSESSMENT.
THE FOLLOWING PROTECTIVE CLOTHING MATERIAL(S) ARE RECOMMENDED:
APRON - POLYMER LAMINATE
RESPIRATORY PROTECTION:
AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF A RESPIRATOR IS REQUIRED.
IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS PART OF A FULL RESPIRATORY
PROTECTION PROGRAM. BASED ON THE RESULTS OF THE EXPOSURE ASSESSMENT, SELECT
FROM THE FOLLOWING RESPIRATOR TYPE(S) TO REDUCE INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
ORGANIC VAPORS AND PARTICULATES
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: LIQUID
SPECIFIC PHYSICAL FORM: VISCOUS
ODOR, COLOR, GRADE: WHITE CREAM, VERY SLIGHT ODOR
ODOR THRESHOLD: NO DATA AVAILABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: NOT APPLICABLE
FLASH POINT: >=248 DEG. C [TEST METHOD: PENSKY-MARTENS CLOSED CUP]
EVAPORATION RATE: NOT APPLICABLE
FLAMMABILITY (SOLID, GAS): NOT APPLICABLE
FLAMMABLE LIMITS(LEL): NOT APPLICABLE
FLAMMABLE LIMITS(UEL): NOT APPLICABLE
VAPOR PRESSURE: <=0.1 MMHg [@ 25 DEG. C]
VAPOR DENSITY: NOT APPLICABLE
DENSITY: 1.33 G/ML
SPECIFIC GRAVITY: 1.33 [REF STD: WATER=1]
SOLUBILITY IN WATER: NIL
SOLUBILITY- NON-WATER: NO DATA AVAILABLE
PARTITION COEFFICIENT N-OCTANOL/WATER: NO DATA AVAILABLE
AUTOIGNITION TEMPERATURE: NOT APPLICABLE
DECOMPOSITION TEMPERATURE: NO DATA AVAILABLE
VISCOSITY: 100,000 CENTIPOISE
HAZARDOUS AIR POLLUTANTS: 0% WEIGHT [TEST METHOD: CALCULATED]
MOLECULAR WEIGHT: NO DATA AVAILABLE
VOC LESS H2O & EXEMPT SOLVENTS:
<5 G/L [TEST METHOD: CALCULATED SCAQMD RULE 443.1]
[DETAILS: WHEN USED AS INTENDED WITH PART A]
VOC LESS H2O & EXEMPT SOLVENTS:
0 G/L [TEST METHOD: CALCULATED SCAQMD RULE 443.1] [DETAILS: AS SUPPLIED]
VOC LESS H2O & EXEMPT SOLVENTS:
<0.5% [TEST METHOD: CALCULATED SCAQMD RULE 443.1]
[DETAILS: WHEN USED AS INTENDED WITH PART B]
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL MAY BE REACTIVE WITH CERTAIN AGENTS UNDER CERTAIN
CONDITIONS - SEE THE REMAINING HEADINGS IN THIS SECTION.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID:
HEAT IS GENERATED DURING CURE. DO NOT CURE A MASS LARGER THAN 50 GRAMS IN
A CONFINED SPACE TO PREVENT A PREMATURE EXOTHERMIC REACTION WITH PRODUCTION
OF INTENSE HEAT AND SMOKE.
10.5. INCOMPATIBLE MATERIALS:
STRONG ACIDS
STRONG OXIDIZING AGENTS
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR THE
SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT BELOW
THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION: MAY CAUSE ADDITIONAL HEALTH EFFECTS (SEE BELOW).
SKIN CONTACT:
MILD SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE LOCALIZED REDNESS, SWELLING, ITCHING, AND
DRYNESS.
ALLERGIC SKIN REACTION (NON-PHOTO INDUCED):
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, BLISTERING, AND ITCHING.
EYE CONTACT:
MODERATE EYE IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND BLURRED
OR HAZY VISION.
INGESTION:
GASTROINTESTINAL IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABDOMINAL PAIN, STOMACH UPSET, NAUSEA, VOMITING
AND DIARRHEA.
ADDITIONAL HEALTH EFFECTS:
PROLONGED OR REPEATED EXPOSURE MAY CAUSE TARGET ORGAN EFFECTS:
PNEUMOCONIOSIS:
SIGN/SYMPTOMS MAY INCLUDE PERSISTENT COUGH, BREATHLESSNESS, CHEST PAIN,
INCREASED AMOUNTS OF SPUTUM, AND CHANGES IN LUNG FUNCTION TESTS.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT INGESTION NO DATA AVAILABLE;
CALCULATED ATE: >5,000 MG/KG
EPOXY RESIN DERMAL RAT LD50: >1,600 MG/KG
EPOXY RESIN INGESTION RAT LD50: >1,000 MG/KG
KAOLIN DERMAL LD50:
ESTIMATED TO BE >5,000 MG/KG
KAOLIN INGESTION HUMAN LD50: >15,000 MG/KG
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
EPOXY RESIN RABBIT MILD IRRITANT
KAOLIN PROFESSIONAL NO SIGNIFICANT IRRITATION
JUDGMENT
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
EPOXY RESIN RABBIT MODERATE IRRITANT
KAOLIN PROFESSIONAL NO SIGNIFICANT IRRITATION
JUDGMENT
SKIN SENSITIZATION:
NAME SPECIES VALUE
EPOXY RESIN HUMAN AND SENSITIZING
ANIMAL
RESPIRATORY SENSITIZATION:
NAME SPECIES VALUE
EPOXY RESIN HUMAN NOT CLASSIFIED
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
EPOXY RESIN IN VIVO NOT MUTAGENIC
EPOXY RESIN IN VITRO SOME POSITIVE DATA EXIST, BUT
THE DATA ARE NOT SUFFICIENT FOR
CLASSIFICATION
CARCINOGENICITY:
NAME ROUTE SPECIES VALUE
EPOXY RESIN DERMAL MOUSE SOME POSITIVE DATA EXIST, BUT
THE DATA ARE NOT SUFFICIENT
FOR CLASSIFICATION
KAOLIN INHALATION MULTIPLE NOT CARCINOGENIC
ANIMAL
SPECIES
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
NAME ROUTE VALUE
EPOXY RESIN INGESTION NOT CLASSIFIED FOR FEMALE REPRODUCTION
EPOXY RESIN INGESTION NOT CLASSIFIED FOR MALE REPRODUCTION
EPOXY RESIN DERMAL NOT CLASSIFIED FOR DEVELOPMENT
EPOXY RESIN INGESTION NOT CLASSIFIED FOR DEVELOPMENT
NAME SPECIES TEST RESULT EXPOSURE DURATION
EPOXY RESIN RAT NOAEL: 2 GENERATION
750 MG/KG/DAY
EPOXY RESIN RAT NOAEL: 2 GENERATION
750 MG/KG/DAY
EPOXY RESIN RABBIT NOAEL: DURING ORGANOGENESIS
300 MG/KG/DAY
EPOXY RESIN RAT NOAEL: 2 GENERATION
750 MG/KG/DAY
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
EPOXY RESIN DERMAL LIVER NOT CLASSIFIED
EPOXY RESIN DERMAL NERVOUS SYSTEM NOT CLASSIFIED
EPOXY RESIN INGESTION AUDITORY SYSTEM NOT CLASSIFIED
HEART
ENDOCRINE SYSTEM
HEMATOPOIETIC SYSTEM
LIVER
EYES
KIDNEY AND/OR BLADDER
KAOLIN INHALATION PNEUMOCONIOSIS CAUSES DAMAGE TO
ORGANS THROUGH
PROLONGED OR REPEATED
EXPOSURE
KAOLIN INHALATION PULMONARY FIBROSIS NOT CLASSIFIED
NAME SPECIES TEST RESULT EXPOSURE DURATION
EPOXY RESIN RAT NOAEL: 2 YEARS
1,000 MG/KG/DAY
EPOXY RESIN RAT NOAEL: 13 WEEKS
1,000 MG/KG/DAY
EPOXY RESIN RAT NOAEL: 28 DAYS
1,000 MG/KG/DAY
KAOLIN HUMAN NOAEL: NA OCCUPATIONAL EXPOSURE
KAOLIN RAT NOAEL:
NOT AVAILABLE
ASPIRATION HAZARD:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH THE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
DISPOSE OF COMPLETELY CURED (OR POLYMERIZED) MATERIAL IN A PERMITTED
INDUSTRIAL WASTE FACILITY. AS A DISPOSAL ALTERNATIVE, INCINERATE UNCURED
PRODUCT IN A PERMITTED WASTE INCINERATION FACILITY. PROPER DESTRUCTION MAY
REQUIRE THE USE OF ADDITIONAL FUEL DURING INCINERATION PROCESSES.
COMBUSTION PRODUCTS WILL INCLUDE HALOGEN ACID (HCL/HF/HBR). FACILITY
MUST BE CAPABLE OF HANDLING HALOGENATED MATERIALS. EMPTY DRUMS/BARRELS/
CONTAINERS USED FOR TRANSPORTING AND HANDLING HAZARDOUS CHEMICALS
(CHEMICAL SUBSTANCES/MIXTURES/PREPARATIONS CLASSIFIED AS HAZARDOUS
AS PER APPLICABLE REGULATIONS) SHALL BE CONSIDERED, STORED, TREATED &
DISPOSED OF AS HAZARDOUS WASTES UNLESS OTHERWISE DEFINED BY APPLICABLE
WASTE REGULATIONS. CONSULT WITH THE RESPECTIVE REGULATING AUTHORITIES
TO DETERMINE THE AVAILABLE TREATMENT AND DISPOSAL FACILITIES.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
| SECTION 14: TRANSPORT INFORMATION | |
FOR TRANSPORT INFORMATION, PLEASE VISIT:
HTTP://3M.COM/TRANSPORTINFO OR CALL 1-800-364-3577 OR 651-737-6501.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
EPCRA 311/312 HAZARD CLASSIFICATIONS:
PHYSICAL HAZARDS: NOT APPLICABLE
HEALTH HAZARDS:
RESPIRATORY OR SKIN SENSITIZATION
SERIOUS EYE DAMAGE OR EYE IRRITATION
SPECIFIC TARGET ORGAN TOXICITY (SINGLE OR REPEATED EXPOSURE)
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
15.3. CHEMICAL INVENTORIES:
THE COMPONENTS OF THIS PRODUCT ARE IN COMPLIANCE WITH THE CHEMICAL
NOTIFICATION REQUIREMENTS OF TSCA. ALL REQUIRED COMPONENTS OF THIS
PRODUCT ARE LISTED ON THE ACTIVE PORTION OF THE TSCA INVENTORY.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 2
FLAMMABILITY 1
INSTABILITY 1
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED
FOR USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO INCLUDE
THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT ARE KNOWN
TO BE GENERATED IN SIGNIFICANT QUANTITIES.
DOCUMENT GROUP: 10-3348-9
VERSION NUMBER: 33.00
ISSUE DATE: 05/21/18
SUPERCEDES DATE: 04/03/18
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP190 GRAY, PART A
01/29/21
3M
SAFETY DATA SHEET
COPYRIGHT, 2021, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR
THE PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 10-3349-7
VERSION NUMBER: 34.01
ISSUE DATE: 01/29/21
SUPERCEDES DATE: 05/21/18
| SECTION 1: IDENTIFICATION | |
1.1. PRODUCT IDENTIFIER:
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP190 GRAY, PART A
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE: STRUCTURAL ADHESIVE
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: INDUSTRIAL ADHESIVES AND TAPES DIVISION
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
SERIOUS EYE DAMAGE/IRRITATION: CATEGORY 1.
SKIN CORROSION/IRRITATION: CATEGORY 2.
SKIN SENSITIZER: CATEGORY 1A.
REPRODUCTIVE TOXICITY: CATEGORY 1B.
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE): CATEGORY 3.
2.2. LABEL ELEMENTS:
SIGNAL WORD: DANGER
SYMBOLS:
CORROSION
EXCLAMATION MARK
HEALTH HAZARD
PICTOGRAMS:
CORROSION
EXCLAMATION MARK
HEALTH HAZARD
HAZARD STATEMENTS:
CAUSES SERIOUS EYE DAMAGE.
CAUSES SKIN IRRITATION.
MAY CAUSE AN ALLERGIC SKIN REACTION.
MAY CAUSE DROWSINESS OR DIZZINESS.
MAY DAMAGE FERTILITY OR THE UNBORN CHILD.
PRECAUTIONARY STATEMENTS:
PREVENTION:
OBTAIN SPECIAL INSTRUCTIONS BEFORE USE.
DO NOT HANDLE UNTIL ALL SAFETY PRECAUTIONS HAVE BEEN READ AND UNDERSTOOD.
AVOID BREATHING DUST/FUME/GAS/MIST/VAPORS/SPRAY.
USE ONLY OUTDOORS OR IN A WELL-VENTILATED AREA.
WEAR PROTECTIVE GLOVES AND EYE/FACE PROTECTION.
WASH THOROUGHLY AFTER HANDLING.
CONTAMINATED WORK CLOTHING MUST NOT BE ALLOWED OUT OF THE WORKPLACE.
RESPONSE:
IF INHALED: REMOVE PERSON TO FRESH AIR AND KEEP COMFORTABLE FOR BREATHING.
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES,
IF PRESENT AND EASY TO DO. CONTINUE RINSING.
IF ON SKIN: WASH WITH PLENTY OF SOAP AND WATER.
IMMEDIATELY CALL A POISON CENTER OR DOCTOR/PHYSICIAN.
IF SKIN IRRITATION OR RASH OCCURS: GET MEDICAL ADVICE/ATTENTION.
TAKE OFF CONTAMINATED CLOTHING AND WASH IT BEFORE REUSE.
IF EXPOSED OR CONCERNED: GET MEDICAL ADVICE/ATTENTION.
STORAGE:
STORE IN A WELL-VENTILATED PLACE. KEEP CONTAINER TIGHTLY CLOSED.
STORE LOCKED UP.
DISPOSAL:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH APPLICABLE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
SUPPLEMENTAL INFORMATION:
PERSONS PREVIOUSLY SENSITIZED TO AMINES MAY DEVELOP A CROSS-SENSITIZATION
REACTION TO CERTAIN OTHER AMINES.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
ALIPHATIC POLYMER DIAMINE 68911-25-1 40 - 60 TRADE SECRET*
KAOLIN 1332-58-7 20 - 40 TRADE SECRET*
4,7,10-TRIOXATRIDECANE-1,13-DIAMINE 4246-51-9 1 - 10 TRADE SECRET*
TOLUENE 108-88-3 <0.5 TRADE SECRET*
*THE SPECIFIC CHEMICAL IDENTITY AND/OR EXACT PERCENTAGE (CONCENTRATION)
OF THIS COMPOSITION HAS BEEN WITHHELD AS A TRADE SECRET.
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
IMMEDIATELY WASH WITH SOAP AND WATER. REMOVE CONTAMINATED CLOTHING AND
WASH BEFORE REUSE. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL ATTENTION.
EYE CONTACT:
IMMEDIATELY FLUSH WITH LARGE AMOUNTS OF WATER FOR AT LEAST 15 MINUTES.
REMOVE CONTACT LENSES IF EASY TO DO. CONTINUE RINSING. IMMEDIATELY GET
MEDICAL ATTENTION.
IF SWALLOWED: RINSE MOUTH. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
NO CRITICAL SYMPTOMS OR EFFECTS. SEE SECTION 11.1, INFORMATION ON
TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED: NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
IN CASE OF FIRE:
USE A FIRE FIGHTING AGENT SUITABLE FOR ORDINARY COMBUSTIBLE MATERIAL SUCH
AS WATER OR FOAM TO EXTINGUISH.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
NONE INHERENT IN THIS PRODUCT.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
AMINE COMPOUNDS DURING COMBUSTION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
OXIDES OF NITROGEN DURING COMBUSTION
TOXIC VAPOR, GAS, PARTICULATE DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
WEAR FULL PROTECTIVE CLOTHING, INCLUDING HELMET, SELF-CONTAINED, POSITIVE
PRESSURE OR PRESSURE DEMAND BREATHING APPARATUS, BUNKER COAT AND PANTS,
BANDS AROUND ARMS, WAIST AND LEGS, FACE MASK, AND PROTECTIVE COVERING FOR
EXPOSED AREAS OF THE HEAD.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
EVACUATE AREA. VENTILATE THE AREA WITH FRESH AIR. FOR LARGE SPILL, OR
SPILLS IN CONFINED SPACES, PROVIDE MECHANICAL VENTILATION TO DISPERSE OR
EXHAUST VAPORS, IN ACCORDANCE WITH GOOD INDUSTRIAL HYGIENE PRACTICE. REFER
TO OTHER SECTIONS OF THIS SDS FOR INFORMATION REGARDING PHYSICAL AND HEALTH
HAZARDS, RESPIRATORY PROTECTION, VENTILATION, AND PERSONAL PROTECTIVE
EQUIPMENT.
6.2. ENVIRONMENTAL PRECAUTIONS:
AVOID RELEASE TO THE ENVIRONMENT. FOR LARGER SPILLS, COVER DRAINS AND
BUILD DIKES TO PREVENT ENTRY INTO SEWER SYSTEMS OR BODIES OF WATER.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP:
CONTAIN SPILL. WORKING FROM AROUND THE EDGES OF THE SPILL INWARD, COVER
WITH BENTONITE, VERMICULITE, OR COMMERCIALLY AVAILABLE INORGANIC ABSORBENT
MATERIAL. MIX IN SUFFICIENT ABSORBENT UNTIL IT APPEARS DRY. REMEMBER,
ADDING AN ABSORBENT MATERIAL DOES NOT REMOVE A PHYSICAL, HEALTH, OR
ENVIRONMENTAL HAZARD. COLLECT AS MUCH OF THE SPILLED MATERIAL AS POSSIBLE.
PLACE IN A CLOSED CONTAINER APPROVED FOR TRANSPORTATION BY APPROPRIATE
AUTHORITIES. CLEAN UP RESIDUE WITH AN APPROPRIATE SOLVENT SELECTED BY A
QUALIFIED AND AUTHORIZED PERSON. VENTILATE THE AREA WITH FRESH AIR. READ
AND FOLLOW SAFETY PRECAUTIONS ON THE SOLVENT LABEL AND SDS. SEAL THE
CONTAINER. DISPOSE OF COLLECTED MATERIAL AS SOON AS POSSIBLE IN ACCORDANCE
WITH APPLICABLE LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
FOR INDUSTRIAL/OCCUPATIONAL USE ONLY. NOT FOR CONSUMER SALE OR USE. DO NOT
HANDLE UNTIL ALL SAFETY PRECAUTIONS HAVE BEEN READ AND UNDERSTOOD. DO NOT
BREATHE DUST/FUME/GAS/MIST/VAPORS/SPRAY. DO NOT GET IN EYES, ON SKIN, OR
ON CLOTHING. DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT. WASH
THOROUGHLY AFTER HANDLING. CONTAMINATED WORK CLOTHING SHOULD NOT BE ALLOWED
OUT OF THE WORKPLACE. AVOID RELEASE TO THE ENVIRONMENT. WASH CONTAMINATED
CLOTHING BEFORE REUSE. AVOID CONTACT WITH OXIDIZING AGENTS (EG. CHLORINE,
CHROMIC ACID ETC.) USE PERSONAL PROTECTIVE EQUIPMENT (GLOVES, RESPIRATORS,
ETC.) AS REQUIRED.
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
STORE IN A WELL-VENTILATED PLACE. KEEP CONTAINER TIGHTLY CLOSED. STORE AWAY
FROM OXIDIZING AGENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN THE TABLE
BELOW, AN OCCUPATIONAL EXPOSURE LIMIT IS NOT AVAILABLE FOR THE COMPONENT.
INGREDIENT C.A.S. NO. AGENCY LIMIT TYPE ADDITIONAL
COMMENTS
TOLUENE 108-88-3 ACGIH TWA: 20 PPM A4:
NOT CLASS.
AS HUMAN
CARCIN,
OTOTOXICANT
TOLUENE 108-88-3 OSHA TWA: 200 PPM
CEIL: 300 PPM
KAOLIN 1332-58-7 ACGIH TWA (RESPIRABLE A4:
FRACTION): 2 MG/M3 NOT CLASS.
AS HUMAN
CARCIN
KAOLIN, TOTAL DUST 1332-58-7 OSHA TWA (AS TOTAL
DUST): 15 MG/M3
TWA (RESPIRABLE
FRACTION): 5 MG/M3
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
AIHA: AMERICAN INDUSTRIAL HYGIENE ASSOCIATION
CMRG: CHEMICAL MANUFACTURER'S RECOMMENDED GUIDELINES
OSHA:
UNITED STATES DEPARTMENT OF LABOR - OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION
TWA: TIME-WEIGHTED-AVERAGE
STEL: SHORT TERM EXPOSURE LIMIT
CEIL: CEILING
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO
CONTROL AIRBORNE EXPOSURES TO BELOW RELEVANT EXPOSURE LIMITS AND/OR
CONTROL DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS NOT ADEQUATE,
USE RESPIRATORY PROTECTION EQUIPMENT.
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON THE RESULTS
OF AN EXPOSURE ASSESSMENT.
THE FOLLOWING EYE/FACE PROTECTION(S) ARE RECOMMENDED:
FULL FACE SHIELD
INDIRECT VENTED GOGGLES
SKIN/HAND PROTECTION:
SELECT AND USE GLOVES AND/OR PROTECTIVE CLOTHING APPROVED TO RELEVANT LOCAL
STANDARDS TO PREVENT SKIN CONTACT BASED ON THE RESULTS OF AN EXPOSURE
ASSESSMENT. SELECTION SHOULD BE BASED ON USE FACTORS SUCH AS EXPOSURE
LEVELS, CONCENTRATION OF THE SUBSTANCE OR MIXTURE, FREQUENCY AND DURATION,
PHYSICAL CHALLENGES SUCH AS TEMPERATURE EXTREMES, AND OTHER USE CONDITIONS.
CONSULT WITH YOUR GLOVE AND/OR PROTECTIVE CLOTHING MANUFACTURER FOR
SELECTION OF APPROPRIATE COMPATIBLE GLOVES/PROTECTIVE CLOTHING.
NOTE:
NITRILE GLOVES MAY BE WORN OVER POLYMER LAMINATE GLOVES TO IMPROVE
DEXTERITY.
GLOVES MADE FROM THE FOLLOWING MATERIAL(S) ARE RECOMMENDED:
POLYMER LAMINATE
RESPIRATORY PROTECTION:
AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF A RESPIRATOR IS REQUIRED.
IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS PART OF A FULL RESPIRATORY
PROTECTION PROGRAM.
BASED ON THE RESULTS OF THE EXPOSURE ASSESSMENT, SELECT FROM THE FOLLOWING
RESPIRATOR TYPE(S) TO REDUCE INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
ORGANIC VAPORS AND PARTICULATES
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
APPEARANCE:
PHYSICAL STATE: LIQUID
COLOR: GRAY
SPECIFIC PHYSICAL FORM: VISCOUS LIQUID
ODOR: AMINE
ODOR THRESHOLD: NO DATA AVAILABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: >=250 DEG. F
FLASH POINT: >=94 DEG. C [TEST METHOD: CLOSED CUP]
EVAPORATION RATE: NEGLIGIBLE
FLAMMABILITY (SOLID, GAS): NOT APPLICABLE
FLAMMABLE LIMITS(LEL): NO DATA AVAILABLE
FLAMMABLE LIMITS(UEL): NO DATA AVAILABLE
VAPOR PRESSURE: <=0.1 MMHg [@ 25 DEG. C]
VAPOR DENSITY: NOT APPLICABLE
DENSITY: 1.26 G/ML [@ 20 DEG. C]
SPECIFIC GRAVITY: 1.26 [REF STD: WATER=1]
SOLUBILITY IN WATER: NIL
SOLUBILITY- NON-WATER: NO DATA AVAILABLE
PARTITION COEFFICIENT N-OCTANOL/WATER: NO DATA AVAILABLE
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
DECOMPOSITION TEMPERATURE: NO DATA AVAILABLE
VISCOSITY:
40,000 - 65,000 CENTIPOISE [@ 75 DEG. F] [TEST METHOD: BROOKFIELD]
HAZARDOUS AIR POLLUTANTS: <0% WEIGHT [TEST METHOD: CALCULATED]
MOLECULAR WEIGHT: NO DATA AVAILABLE
VOC LESS H2O & EXEMPT SOLVENTS:
<5 G/L [TEST METHOD: CALCULATED SCAQMD RULE 443.1]
[DETAILS: WHEN USED AS INTENDED WITH PART B]
VOC LESS H2O & EXEMPT SOLVENTS:
<7 G/L [TEST METHOD: CALCULATED SCAQMD RULE 443.1]
[DETAILS: AS SUPPLIED]
VOC LESS H2O & EXEMPT SOLVENTS:
<0.5% [TEST METHOD: CALCULATED SCAQMD RULE 443.1]
[DETAILS: WHEN USED AS INTENDED WITH PART B]
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL MAY BE REACTIVE WITH CERTAIN AGENTS UNDER CERTAIN
CONDITIONS - SEE THE REMAINING HEADINGS IN THIS SECTION.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID:
HEAT IS GENERATED DURING CURE. DO NOT CURE A MASS LARGER THAN 50 GRAMS IN
A CONFINED SPACE TO PREVENT A PREMATURE EXOTHERMIC REACTION WITH PRODUCTION
OF INTENSE HEAT AND SMOKE.
10.5. INCOMPATIBLE MATERIALS: STRONG OXIDIZING AGENTS
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR THE
SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT BELOW
THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
RESPIRATORY TRACT IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL DISCHARGE, HEADACHE,
HOARSENESS, AND NOSE AND THROAT PAIN.
MAY CAUSE ADDITIONAL HEALTH EFFECTS (SEE BELOW).
SKIN CONTACT:
SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE LOCALIZED REDNESS, SWELLING, ITCHING, DRYNESS,
CRACKING, BLISTERING, AND PAIN.
ALLERGIC SKIN REACTION (NON-PHOTO INDUCED):
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, BLISTERING, AND ITCHING.
EYE CONTACT:
CORROSIVE (EYE BURNS):
SIGNS/SYMPTOMS MAY INCLUDE CLOUDY APPEARANCE OF THE CORNEA, CHEMICAL BURNS,
SEVERE PAIN, TEARING, ULCERATIONS, SIGNIFICANTLY IMPAIRED VISION OR
COMPLETE LOSS OF VISION.
INGESTION: MAY BE HARMFUL IF SWALLOWED.
GASTROINTESTINAL IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABDOMINAL PAIN, STOMACH UPSET, NAUSEA, VOMITING
AND DIARRHEA.
MAY CAUSE ADDITIONAL HEALTH EFFECTS (SEE BELOW).
ADDITIONAL HEALTH EFFECTS:
SINGLE EXPOSURE MAY CAUSE TARGET ORGAN EFFECTS:
CENTRAL NERVOUS SYSTEM (CNS) DEPRESSION:
SIGNS/SYMPTOMS MAY INCLUDE HEADACHE, DIZZINESS, DROWSINESS, INCOORDINATION,
NAUSEA, SLOWED REACTION TIME, SLURRED SPEECH, GIDDINESS, AND
UNCONSCIOUSNESS.
REPRODUCTIVE/DEVELOPMENTAL TOXICITY:
CONTAINS A CHEMICAL OR CHEMICALS WHICH CAN CAUSE BIRTH DEFECTS OR OTHER
REPRODUCTIVE HARM.
ADDITIONAL INFORMATION:
PERSONS PREVIOUSLY SENSITIZED TO AMINES MAY DEVELOP A CROSS-SENSITIZATION
REACTION TO CERTAIN OTHER AMINES.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT DERMAL NO DATA AVAILABLE;
CALCULATED ATE:
>5,000 MG/KG
OVERALL PRODUCT INGESTION NO DATA AVAILABLE;
CALCULATED ATE:
2,000 - 5,000 MG/KG
ALIPHATIC POLYMER DIAMINE DERMAL RAT LD50: >2,000 MG/KG
ALIPHATIC POLYMER DIAMINE INGESTION RAT LD50: >2,000 MG/KG
KAOLIN DERMAL LD50:
ESTIMATED TO BE
>5,000 MG/KG
KAOLIN INGESTION HUMAN LD50: >15,000 MG/KG
4,7,10-TRIOXATRIDECANE- DERMAL RABBIT LD50: 2,500 MG/KG
1,13-DIAMINE
4,7,10-TRIOXATRIDECANE- INGESTION RAT LD50: 3,160 MG/KG
1,13-DIAMINE
TOLUENE DERMAL RAT LD50: 12,000 MG/KG
TOLUENE INHALATION- RAT LC50: 30 MG/L
VAPOR
(4 HOURS)
TOLUENE INGESTION RAT LD50: 5,550 MG/KG
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
ALIPHATIC POLYMER DIAMINE RAT IRRITANT
KAOLIN PROFESSIONAL NO SIGNIFICANT IRRITATION
JUDGMENT
4,7,10-TRIOXATRIDECANE- RABBIT CORROSIVE
1,13-DIAMINE
TOLUENE RABBIT IRRITANT
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
ALIPHATIC POLYMER DIAMINE IN VITRO SEVERE IRRITANT
DATA
KAOLIN PROFESSIONAL NO SIGNIFICANT IRRITATION
JUDGMENT
4,7,10-TRIOXATRIDECANE- SIMILAR CORROSIVE
1,13-DIAMINE HEALTH
HAZARDS
TOLUENE RABBIT MODERATE IRRITANT
SKIN SENSITIZATION:
NAME SPECIES VALUE
ALIPHATIC POLYMER DIAMINE GUINEA PIG SENSITIZING
TOLUENE GUINEA PIG NOT CLASSIFIED
RESPIRATORY SENSITIZATION:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
ALIPHATIC POLYMER DIAMINE IN VITRO NOT MUTAGENIC
TOLUENE IN VITRO NOT MUTAGENIC
TOLUENE IN VIVO NOT MUTAGENIC
CARCINOGENICITY:
NAME ROUTE SPECIES VALUE
KAOLIN INHALATION MULTIPLE NOT CARCINOGENIC
ANIMAL
SPECIES
TOLUENE DERMAL MOUSE SOME POSITIVE DATA EXIST, BUT
THE DATA ARE NOT SUFFICIENT
FOR CLASSIFICATION
TOLUENE INGESTION RAT SOME POSITIVE DATA EXIST, BUT
THE DATA ARE NOT SUFFICIENT
FOR CLASSIFICATION
TOLUENE INHALATION MOUSE SOME POSITIVE DATA EXIST, BUT
THE DATA ARE NOT SUFFICIENT
FOR CLASSIFICATION
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
NAME ROUTE VALUE
ALIPHATIC POLYMER INGESTION NOT CLASSIFIED FOR FEMALE REPRODUCTION
DIAMINE
ALIPHATIC POLYMER INGESTION NOT CLASSIFIED FOR MALE REPRODUCTION
DIAMINE
ALIPHATIC POLYMER INGESTION NOT CLASSIFIED FOR DEVELOPMENT
DIAMINE
TOLUENE INHALATION NOT CLASSIFIED FOR FEMALE REPRODUCTION
TOLUENE INHALATION NOT CLASSIFIED FOR MALE REPRODUCTION
TOLUENE INGESTION TOXIC TO DEVELOPMENT
TOLUENE INHALATION TOXIC TO DEVELOPMENT
NAME SPECIES TEST RESULT EXPOSURE DURATION
ALIPHATIC POLYMER RAT NOAEL: PREMATING INTO
DIAMINE 1,000 MG/KG/DAY LACTATION
ALIPHATIC POLYMER RAT NOAEL: 29 DAYS
DIAMINE 1,000 MG/KG/DAY
ALIPHATIC POLYMER RAT NOAEL: PREMATING INTO
DIAMINE 1,000 MG/KG/DAY LACTATION
TOLUENE HUMAN NOAEL: OCCUPATIONAL
NOT AVAILABLE EXPOSURE
TOLUENE RAT NOAEL: 2.3 MG/L 1 GENERATION
TOLUENE RAT LOAEL: DURING GESTATION
520 MG/KG/DAY
TOLUENE HUMAN NOAEL: POISONING
NOT AVAILABLE AND/OR ABUSE
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
ALIPHATIC POLYMER INHALATION RESPIRATORY SOME POSITIVE DATA
DIAMINE IRRITATION EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
ALIPHATIC POLYMER INGESTION CENTRAL NERVOUS MAY CAUSE DROWSINESS
DIAMINE SYSTEM DEPRESSION OR DIZZINESS
4,7,10- INHALATION RESPIRATORY SOME POSITIVE DATA
TRIOXATRIDECANE- IRRITATION EXIST, BUT THE DATA
1,13-DIAMINE ARE NOT SUFFICIENT
FOR CLASSIFICATION
TOLUENE INHALATION CENTRAL NERVOUS MAY CAUSE DROWSINESS
SYSTEM DEPRESSION OR DIZZINESS
TOLUENE INHALATION RESPIRATORY SOME POSITIVE DATA
IRRITATION EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
TOLUENE INHALATION IMMUNE SYSTEM NOT CLASSIFIED
TOLUENE INGESTION CENTRAL NERVOUS MAY CAUSE DROWSINESS
SYSTEM DEPRESSION OR DIZZINESS
NAME SPECIES TEST RESULT EXPOSURE DURATION
ALIPHATIC POLYMER SIMILAR IRRITATION
DIAMINE HEALTH POSITIVE
HAZARDS
ALIPHATIC POLYMER RAT NOAEL:
DIAMINE NOT AVAILABLE
4,7,10-TRIOXATRIDECANE- NOAEL:
1,13-DIAMINE NOT AVAILABLE
TOLUENE HUMAN NOAEL:
NOT AVAILABLE
TOLUENE HUMAN NOAEL:
NOT AVAILABLE
TOLUENE MOUSE NOAEL: 3 HOURS
0.004 MG/L
TOLUENE HUMAN NOAEL: POISONING
NOT AVAILABLE AND/OR ABUSE
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
ALIPHATIC POLYMER INGESTION HEART NOT CLASSIFIED
DIAMINE SKIN
ENDOCRINE SYSTEM
GASTROINTESTINAL
TRACT
BONE, TEETH, NAILS,
AND/OR HAIR
HEMATOPOIETIC
SYSTEM
LIVER
IMMUNE SYSTEM
MUSCLES
NERVOUS SYSTEM
EYES
KIDNEY AND/OR
BLADDER
RESPIRATORY
SYSTEM
VASCULAR SYSTEM
KAOLIN INHALATION PNEUMOCONIOSIS CAUSES DAMAGE TO
ORGANS THROUGH
PROLONGED OR
REPEATED EXPOSURE
KAOLIN INHALATION PULMONARY FIBROSIS NOT CLASSIFIED
TOLUENE INHALATION AUDITORY SYSTEM CAUSES DAMAGE TO
EYES ORGANS THROUGH
OLFACTORY SYSTEM PROLONGED OR
REPEATED EXPOSURE
TOLUENE INHALATION NERVOUS SYSTEM MAY CAUSE DAMAGE
TO ORGANS THOUGH
PROLONGED OR
REPEATED EXPOSURE
TOLUENE INHALATION RESPIRATORY SYSTEM SOME POSITIVE DATA
EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
TOLUENE INHALATION HEART NOT CLASSIFIED
LIVER
KIDNEY AND/OR
BLADDER
TOLUENE INHALATION ENDOCRINE SYSTEM NOT CLASSIFIED
TOLUENE INHALATION IMMUNE SYSTEM NOT CLASSIFIED
TOLUENE INHALATION BONE, TEETH, NAILS, NOT CLASSIFIED
AND/OR HAIR
TOLUENE INHALATION HEMATOPOIETIC NOT CLASSIFIED
SYSTEM
VASCULAR SYSTEM
TOLUENE INHALATION GASTROINTESTINAL NOT CLASSIFIED
TRACT
TOLUENE INGESTION NERVOUS SYSTEM SOME POSITIVE DATA
EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
TOLUENE INGESTION HEART NOT CLASSIFIED RAT
TOLUENE INGESTION LIVER NOT CLASSIFIED
KIDNEY AND/OR
BLADDER
TOLUENE INGESTION HEMATOPOIETIC NOT CLASSIFIED
SYSTEM
TOLUENE INGESTION ENDOCRINE SYSTEM NOT CLASSIFIED
TOLUENE INGESTION IMMUNE SYSTEM NOT CLASSIFIED
NAME SPECIES TEST RESULT EXPOSURE DURATION
ALIPHATIC POLYMER RAT NOAEL: 29 DAYS
DIAMINE 1,000 MG/KG/DAY
KAOLIN HUMAN NOAEL: NA OCCUPATIONAL
EXPOSURE
KAOLIN RAT NOAEL:
NOT AVAILABLE
TOLUENE HUMAN NOAEL: POISONING
NOT AVAILABLE AND/OR ABUSE
TOLUENE HUMAN NOAEL: POISONING
NOT AVAILABLE AND/OR ABUSE
TOLUENE RAT LOAEL: 2.3 MG/L 15 MONTHS
TOLUENE RAT NOAEL: 11.3 MG/L 15 WEEKS
TOLUENE RAT NOAEL: 1.1 MG/L 4 WEEKS
TOLUENE MOUSE NOAEL: 20 DAYS
NOT AVAILABLE
TOLUENE MOUSE NOAEL: 1.1 MG/L 8 WEEKS
TOLUENE HUMAN NOAEL: OCCUPATIONAL
NOT AVAILABLE EXPOSURE
TOLUENE MULTIPLE NOAEL: 11.3 MG/L 15 WEEKS
ANIMAL
SPECIES
TOLUENE RAT NOAEL: 13 WEEKS
625 MG/KG/DAY
TOLUENE RAT NOAEL: 13 WEEKS
2,500 MG/KG/DAY
TOLUENE MULTIPLE NOAEL: 13 WEEKS
ANIMAL 2,500 MG/KG/DAY
SPECIES
TOLUENE MOUSE NOAEL: 14 DAYS
600 MG/KG/DAY
TOLUENE MOUSE NOAEL: 28 DAYS
105 MG/KG/DAY
TOLUENE MOUSE NOAEL: 4 WEEKS
105 MG/KG/DAY
ASPIRATION HAZARD:
NAME VALUE
TOLUENE ASPIRATION HAZARD
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH THE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
DISPOSE OF COMPLETELY CURED (OR POLYMERIZED) MATERIAL IN A PERMITTED
INDUSTRIAL WASTE FACILITY. AS A DISPOSAL ALTERNATIVE, INCINERATE UNCURED
PRODUCT IN A PERMITTED WASTE INCINERATION FACILITY. PROPER DESTRUCTION MAY
REQUIRE THE USE OF ADDITIONAL FUEL DURING INCINERATION PROCESSES. EMPTY
DRUMS/BARRELS/CONTAINERS USED FOR TRANSPORTING AND HANDLING HAZARDOUS
CHEMICALS (CHEMICAL SUBSTANCES/MIXTURES/PREPARATIONS CLASSIFIED AS
HAZARDOUS AS PER APPLICABLE REGULATIONS) SHALL BE CONSIDERED, STORED,
TREATED & DISPOSED OF AS HAZARDOUS WASTES UNLESS OTHERWISE DEFINED BY
APPLICABLE WASTE REGULATIONS. CONSULT WITH THE RESPECTIVE REGULATING
AUTHORITIES TO DETERMINE THE AVAILABLE TREATMENT AND DISPOSAL FACILITIES.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
| SECTION 14: TRANSPORT INFORMATION | |
FOR TRANSPORT INFORMATION, PLEASE VISIT:
HTTP://3M.COM/TRANSPORTINFO OR CALL 1-800-364-3577 OR 651-737-6501.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
EPCRA 311/312 HAZARD CLASSIFICATIONS:
PHYSICAL HAZARDS: NOT APPLICABLE
HEALTH HAZARDS:
REPRODUCTIVE TOXICITY
RESPIRATORY OR SKIN SENSITIZATION
SERIOUS EYE DAMAGE OR EYE IRRITATION
SKIN CORROSION OR IRRITATION
SPECIFIC TARGET ORGAN TOXICITY (SINGLE OR REPEATED EXPOSURE)
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
15.3. CHEMICAL INVENTORIES:
THE COMPONENTS OF THIS PRODUCT ARE IN COMPLIANCE WITH THE CHEMICAL
NOTIFICATION REQUIREMENTS OF TSCA. ALL REQUIRED COMPONENTS OF THIS PRODUCT
ARE LISTED ON THE ACTIVE PORTION OF THE TSCA INVENTORY.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 3
FLAMMABILITY 1
INSTABILITY 1
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED
FOR USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO INCLUDE
THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT ARE KNOWN
TO BE GENERATED IN SIGNIFICANT QUANTITIES.
DOCUMENT GROUP: 10-3349-7
VERSION NUMBER: 34.01
ISSUE DATE: 01/29/21
SUPERCEDES DATE: 05/21/18
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M.
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM