| Common Name: | SELF-LEVELING SEAM SEALER, PN 08307 |
| Manufacturer: | 3M |
| SDS Revision Date: | 2/17/2016 |
| SDS Format: | GHS-US |
| Item Number(s): | 2KUU3 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M(TM) SELF-LEVELING SEAM SEALER, PN 08307
02/17/16
3M
SAFETY DATA SHEET
COPYRIGHT, 2016, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR
THE PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 18-2239-4
VERSION NUMBER: 3.01
ISSUE DATE: 02/17/16
SUPERCEDES DATE: 04/13/15
PRODUCT IDENTIFIER: 3M(TM) SELF-LEVELING SEAM SEALER, PN 08307
ID NUMBER(S):
41-0003-8015-8, 41-3700-8997-5, 41-3701-2155-4, 60-9801-0580-7
RECOMMENDED USE: AUTOMOTIVE, TWO-PART EPOXY, SELF-LEVELING SEAM SEALER.
SUPPLIER'S DETAILS
MANUFACTURER: 3M
DIVISION: AUTOMOTIVE AFTERMARKET
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
THIS PRODUCT IS A KIT OR A MULTIPART PRODUCT WHICH CONSISTS OF MULTIPLE,
INDEPENDENTLY PACKAGED COMPONENTS. A SAFETY DATA SHEET (SDS), ARTICLE
INFORMATION SHEET (AIS), OR ARTICLE INFORMATION LETTER (AIL) FOR EACH OF
THESE COMPONENTS IS INCLUDED. PLEASE DO NOT SEPARATE THE COMPONENT
DOCUMENTS FROM THIS COVER SHEET.
THE DOCUMENT NUMBERS FOR COMPONENTS OF THIS PRODUCT ARE:
18-2289-9, 18-2290-7
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM
3M(TM) SELF-LEVELING SEAM SEALER PN 08307 PART A (ACCELERATOR)
02/17/16
3M
SAFETY DATA SHEET
COPYRIGHT, 2016, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR
THE PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 18-2289-9
VERSION NUMBER: 5.00
ISSUE DATE: 02/17/16
SUPERCEDES DATE: 01/21/15
| SECTION 1: IDENTIFICATION |  |
1.1. PRODUCT IDENTIFIER
3M(TM) SELF-LEVELING SEAM SEALER PN 08307 PART A (ACCELERATOR)
PRODUCT IDENTIFICATION NUMBERS: LB-K100-0061-0
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE:
AUTOMOTIVE, THIS ACCELERATOR TO BE USED WITH 3M(TM) SELF-LEVELING SEAM
SEALER - PART B (BASE), TWO-PART EPOXY TYPE SELF-LEVELING SEAM SEALER -
ACCELERATOR
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: AUTOMOTIVE AFTERMARKET
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
THE LABEL ELEMENTS BELOW WERE PREPARED IN ACCORDANCE WITH OSHA HAZARD
COMMUNICATION STANDARD, 29 CFR 1910.1200. THIS INFORMATION MAY BE DIFFERENT
FROM THE ACTUAL PRODUCT LABEL INFORMATION FOR LABELS REGULATED BY OTHER
AGENCIES.
2.1. HAZARD CLASSIFICATION:
SERIOUS EYE DAMAGE/IRRITATION: CATEGORY 1.
SKIN CORROSION/IRRITATION: CATEGORY 1C.
2.2. LABEL ELEMENTS:
SIGNAL WORD: DANGER
SYMBOLS: CORROSION
PICTOGRAMS: CORROSION
HAZARD STATEMENTS: CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
PRECAUTIONARY STATEMENTS:
GENERAL: KEEP OUT OF REACH OF CHILDREN.
PREVENTION:
DO NOT BREATHE DUST/FUME/GAS/MIST/VAPORS/SPRAY.
WEAR PROTECTIVE GLOVES, PROTECTIVE CLOTHING, AND EYE/FACE PROTECTION.
WASH THOROUGHLY AFTER HANDLING.
RESPONSE:
IF INHALED: REMOVE PERSON TO FRESH AIR AND KEEP COMFORTABLE FOR BREATHING.
IF ON SKIN (OR HAIR):
TAKE OFF IMMEDIATELY ALL CONTAMINATED CLOTHING. RINSE SKIN WITH
WATER/SHOWER.
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES, IF
PRESENT AND EASY TO DO.
CONTINUE RINSING.
IMMEDIATELY CALL A POISON CENTER OR DOCTOR/PHYSICIAN.
WASH CONTAMINATED CLOTHING BEFORE REUSE.
IF SWALLOWED: RINSE MOUTH. DO NOT INDUCE VOMITING.
STORAGE: STORE LOCKED UP.
DISPOSAL:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH APPLICABLE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
2.3. HAZARDS NOT OTHERWISE CLASSIFIED:
MAY CAUSE CHEMICAL GASTROINTESTINAL BURNS.
1% OF THE MIXTURE CONSISTS OF INGREDIENTS OF UNKNOWN ACUTE ORAL TOXICITY.
3% OF THE MIXTURE CONSISTS OF INGREDIENTS OF UNKNOWN ACUTE DERMAL TOXICITY.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
MERCAPTAN-TERMINATED EPOXY TRADE SECRET* 60 - 100 TRADE SECRET *
CURING AGENT
TRIS(2,4,6-DIMETHYL- 90-72-2 7 - 13 TRADE SECRET *
AMINOMONOMETHYL)PHENOL
MODIFIED ALKYLPOLYSILOXANE TRADE SECRET* 1 - 5 TRADE SECRET *
COPOLYMER NJTSRN# 800963-5064
BIS[(DIMETHYLAMINO)METHYL] 71074-89-0 <2 TRADE SECRET *
PHENOL
NJTS OR NJTSRN: NEW JERSEY TRADE SECRET REGISTRY NUMBER.
*THE SPECIFIC CHEMICAL IDENTITY AND/OR EXACT PERCENTAGE (CONCENTRATION) OF
THIS COMPOSITION HAS BEEN WITHHELD AS A TRADE SECRET.
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
IMMEDIATELY FLUSH WITH LARGE AMOUNTS OF WATER FOR AT LEAST 15 MINUTES.
REMOVE CONTAMINATED CLOTHING. GET IMMEDIATE MEDICAL ATTENTION. WASH
CLOTHING BEFORE REUSE.
EYE CONTACT:
IMMEDIATELY FLUSH WITH LARGE AMOUNTS OF WATER FOR AT LEAST 15 MINUTES.
REMOVE CONTACT LENSES IF EASY TO DO. CONTINUE RINSING. IMMEDIATELY GET
MEDICAL ATTENTION.
IF SWALLOWED:
RINSE MOUTH. DO NOT INDUCE VOMITING. GET IMMEDIATE MEDICAL ATTENTION.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED: NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
IN CASE OF FIRE:
USE A FIRE FIGHTING AGENT SUITABLE FOR ORDINARY COMBUSTIBLE MATERIAL SUCH
AS WATER OR FOAM TO EXTINGUISH.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
NONE INHERENT IN THIS PRODUCT.
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
NO SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS ARE ANTICIPATED.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
EVACUATE AREA. VENTILATE THE AREA WITH FRESH AIR. FOR LARGE SPILL, OR
SPILLS IN CONFINED SPACES, PROVIDE MECHANICAL VENTILATION TO DISPERSE OR
EXHAUST VAPORS, IN ACCORDANCE WITH GOOD INDUSTRIAL HYGIENE PRACTICE.
6.2. ENVIRONMENTAL PRECAUTIONS: AVOID RELEASE TO THE ENVIRONMENT.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP:
CONTAIN SPILL. WORKING FROM AROUND THE EDGES OF THE SPILL INWARD, COVER
WITH BENTONITE, VERMICULITE, OR COMMERCIALLY AVAILABLE INORGANIC ABSORBENT
MATERIAL. MIX IN SUFFICIENT ABSORBENT UNTIL IT APPEARS DRY. REMEMBER,
ADDING AN ABSORBENT MATERIAL DOES NOT REMOVE A PHYSICAL, HEALTH, OR
ENVIRONMENTAL HAZARD. COLLECT AS MUCH OF THE SPILLED MATERIAL AS POSSIBLE.
PLACE IN A CLOSED CONTAINER APPROVED FOR TRANSPORTATION BY APPROPRIATE
AUTHORITIES. CLEAN UP RESIDUE WITH AN APPROPRIATE SOLVENT SELECTED BY A
QUALIFIED AND AUTHORIZED PERSON. VENTILATE THE AREA WITH FRESH AIR. READ
AND FOLLOW SAFETY PRECAUTIONS ON THE SOLVENT LABEL AND SDS. SEAL THE
CONTAINER. DISPOSE OF COLLECTED MATERIAL AS SOON AS POSSIBLE.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
AVOID BREATHING OF DUST CREATED BY CUTTING, SANDING, GRINDING OR MACHINING.
KEEP OUT OF REACH OF CHILDREN. DO NOT BREATHE DUST/FUME/GAS/MIST/VAPORS/
SPRAY. DO NOT GET IN EYES, ON SKIN, OR ON CLOTHING. DO NOT EAT, DRINK OR
SMOKE WHEN USING THIS PRODUCT. WASH THOROUGHLY AFTER HANDLING. WASH
CONTAMINATED CLOTHING BEFORE REUSE. AVOID CONTACT WITH OXIDIZING AGENTS
(EG. CHLORINE, CHROMIC ACID ETC.)
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
STORE AWAY FROM ACIDS. STORE AWAY FROM OXIDIZING AGENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN THE TABLE
BELOW, AN OCCUPATIONAL EXPOSURE LIMIT IS NOT AVAILABLE FOR THE COMPONENT.
INGREDIENT C.A.S. NO. AGENCY LIMIT TYPE ADDITIONAL COMMENTS
TRIS(2,4,6- 90-72-2 CMRG TWA: 5 PPM
DIMETHYLAMINO-
MONOMETHYL)PHENOL
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
AIHA: AMERICAN INDUSTRIAL HYGIENE ASSOCIATION
CMRG: CHEMICAL MANUFACTURER'S RECOMMENDED GUIDELINES
OSHA:
UNITED STATES DEPARTMENT OF LABOR - OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION
TWA: TIME-WEIGHTED-AVERAGE
STEL: SHORT TERM EXPOSURE LIMIT
CEIL: CEILING
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO
CONTROL AIRBORNE EXPOSURES TO BELOW RELEVANT EXPOSURE LIMITS AND/OR CONTROL
DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS NOT ADEQUATE, USE
RESPIRATORY PROTECTION EQUIPMENT.
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON THE RESULTS
OF AN EXPOSURE ASSESSMENT.
THE FOLLOWING EYE/FACE PROTECTION(S) ARE RECOMMENDED:
FULL FACE SHIELD
INDIRECT VENTED GOGGLES
SKIN/HAND PROTECTION:
SELECT AND USE GLOVES AND/OR PROTECTIVE CLOTHING APPROVED TO RELEVANT LOCAL
STANDARDS TO PREVENT SKIN CONTACT BASED ON THE RESULTS OF AN EXPOSURE
ASSESSMENT. SELECTION SHOULD BE BASED ON USE FACTORS SUCH AS EXPOSURE
LEVELS, CONCENTRATION OF THE SUBSTANCE OR MIXTURE, FREQUENCY AND DURATION,
PHYSICAL CHALLENGES SUCH AS TEMPERATURE EXTREMES, AND OTHER USE CONDITIONS.
CONSULT WITH YOUR GLOVE AND/OR PROTECTIVE CLOTHING MANUFACTURER FOR
SELECTION OF APPROPRIATE COMPATIBLE GLOVES/PROTECTIVE CLOTHING.
GLOVES MADE FROM THE FOLLOWING MATERIAL(S) ARE RECOMMENDED:
BUTYL RUBBER
NITRILE RUBBER
IF THIS PRODUCT IS USED IN A MANNER THAT PRESENTS A HIGHER POTENTIAL FOR
EXPOSURE (EG. SPRAYING, HIGH SPLASH POTENTIAL ETC.), THEN USE OF PROTECTIVE
COVERALLS MAY BE NECESSARY. SELECT AND USE BODY PROTECTION TO PREVENT
CONTACT BASED ON THE RESULTS OF AN EXPOSURE ASSESSMENT. THE FOLLOWING
PROTECTIVE CLOTHING MATERIAL(S) ARE RECOMMENDED: APRON - NITRILE
RESPIRATORY PROTECTION:
AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF A RESPIRATOR IS REQUIRED.
IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS PART OF A FULL RESPIRATORY
PROTECTION PROGRAM.
BASED ON THE RESULTS OF THE EXPOSURE ASSESSMENT, SELECT FROM THE FOLLOWING
RESPIRATOR TYPE(S) TO REDUCE INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
ORGANIC VAPORS
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: LIQUID
ODOR, COLOR, GRADE: YELLOW LIQUID WITH IRRITATING SULFUR-LIKE ODOR.
ODOR THRESHOLD: NO DATA AVAILABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: >=200 DEG. F [TEST METHOD: ESTIMATED]
FLASH POINT >=300 DEG. F [TEST METHOD: CLOSED CUP]
EVAPORATION RATE: NO DATA AVAILABLE
FLAMMABILITY (SOLID, GAS): NOT APPLICABLE
FLAMMABLE LIMITS (LEL): NO DATA AVAILABLE
FLAMMABLE LIMITS (UEL): NO DATA AVAILABLE
VAPOR PRESSURE: <=27 PSIA
VAPOR DENSITY: NO DATA AVAILABLE
DENSITY: 1.12 G/ML
SPECIFIC GRAVITY: 1.12 [REF STD: WATER=1]
SOLUBILITY IN WATER: SLIGHT (LESS THAN 10%)
SOLUBILITY- NON-WATER: NO DATA AVAILABLE
PARTITION COEFFICIENT N-OCTANOL/WATER: NO DATA AVAILABLE
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
DECOMPOSITION TEMPERATURE: NO DATA AVAILABLE
VISCOSITY: 10,000 - 15,000 CENTIPOISE
HAZARDOUS AIR POLLUTANTS:
0.000158 LB HAPS/LB SOLIDS [TEST METHOD: CALCULATED]
VOLATILE ORGANIC COMPOUNDS:
12 G/L [TEST METHOD: CALCULATED SCAQMD RULE 443.1]
VOLATILE ORGANIC COMPOUNDS:
1.1% WEIGHT [TEST METHOD: CALCULATED PER CARB TITLE 2]
VOC LESS H2O & EXEMPT SOLVENTS:
12 G/L [TEST METHOD: CALCULATED SCAQMD RULE 443.1]
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL MAY BE REACTIVE WITH CERTAIN AGENTS UNDER CERTAIN
CONDITIONS - SEE THE REMAINING HEADINGS IN THIS SECTION.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID: NOT DETERMINED
10.5. INCOMPATIBLE MATERIALS:
STRONG ACIDS
STRONG OXIDIZING AGENTS
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
CARBON MONOXIDE NOT SPECIFIED
CARBON DIOXIDE NOT SPECIFIED
OXIDES OF SULFUR NOT SPECIFIED
TOXIC VAPOR, GAS, PARTICULATE NOT SPECIFIED
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR THE
SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT BELOW
THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
RESPIRATORY TRACT IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL DISCHARGE, HEADACHE,
HOARSENESS, AND NOSE AND THROAT PAIN.
SKIN CONTACT:
CORROSIVE (SKIN BURNS):
SIGNS/SYMPTOMS MAY INCLUDE LOCALIZED REDNESS, SWELLING, ITCHING, INTENSE
PAIN, BLISTERING, ULCERATION, AND TISSUE DESTRUCTION.
EYE CONTACT:
CORROSIVE (EYE BURNS):
SIGNS/SYMPTOMS MAY INCLUDE CLOUDY APPEARANCE OF THE CORNEA, CHEMICAL BURNS,
SEVERE PAIN, TEARING, ULCERATIONS, SIGNIFICANTLY IMPAIRED VISION OR
COMPLETE LOSS OF VISION.
INGESTION: MAY BE HARMFUL IF SWALLOWED.
GASTROINTESTINAL CORROSION:
SIGNS/SYMPTOMS MAY INCLUDE SEVERE MOUTH, THROAT AND ABDOMINAL PAIN; NAUSEA;
VOMITING; AND DIARRHEA; BLOOD IN THE FECES AND/OR VOMITUS MAY ALSO BE SEEN.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT DERMAL NO DATA AVAILABLE;
CALCULATED ATE:
>5,000 MG/KG
OVERALL PRODUCT INGESTION NO DATA AVAILABLE;
CALCULATED ATE:
2,000 - 5,000 MG/KG
MERCAPTAN-TERMINATED DERMAL RABBIT LD50: >10,200 MG/KG
EPOXY CURING AGENT
MERCAPTAN-TERMINATED INGESTION RAT LD50: 2,600 MG/KG
EPOXY CURING AGENT
TRIS(2,4,6-DIMETHYL- DERMAL RAT LD50: 1,280 MG/KG
AMINOMONOMETHYL)PHENOL
TRIS(2,4,6-DIMETHYL- INGESTION RAT LD50: 1,000 MG/KG
AMINOMONOMETHYL)PHENOL
BIS[(DIMETHYLAMINO) INGESTION LD50:
METHYL] PHENOL ESTIMATED TO BE
300 - 2,000 MG/KG
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
TRIS(2,4,6-DIMETHYLAMINOMONOMETHYL)PHENOL RABBIT CORROSIVE
BIS[(DIMETHYLAMINO)METHYL] PHENOL SIMILAR COMPOUNDS CORROSIVE
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
TRIS(2,4,6-DIMETHYLAMINOMONOMETHYL)PHENOL RABBIT CORROSIVE
BIS[(DIMETHYLAMINO)METHYL] PHENOL SIMILAR COMPOUNDS CORROSIVE
SKIN SENSITIZATION:
NAME SPECIES VALUE
TRIS(2,4,6-DIMETHYL- GUINEA PIG SOME POSITIVE DATA EXIST, BUT
AMINOMONOMETHYL)PHENOL THE DATA ARE NOT SUFFICIENT
FOR CLASSIFICATION
RESPIRATORY SENSITIZATION:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
TRIS(2,4,6-DIMETHYLAMINOMONOMETHYL)PHENOL IN VITRO NOT MUTAGENIC
CARCINOGENICITY:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
TRIS(2,4,6- INHALATION RESPIRATORY SOME POSITIVE DATA EXIST,
DIMETHYL- IRRITATION BUT THE DATA ARE NOT
AMINOMONO- SUFFICIENT FOR
METHYL)PHENOL CLASSIFICATION
NAME SPECIES TEST RESULT EXPOSURE DURATION
TRIS(2,4,6- NOAEL:
DIMETHYL- NOT AVAILABLE
AMINOMONO-
METHYL)PHENOL
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
TRIS(2,4,6- DERMAL SKIN SOME POSITIVE DATA EXIST, BUT
DIMETHYL- LIVER THE DATA ARE NOT SUFFICIENT
AMINOMONO- NERVOUS SYSTEM FOR CLASSIFICATION
METHYL)PHENOL
TRIS(2,4,6- DERMAL AUDITORY SYSTEM ALL DATA ARE NEGATIVE
DIMETHYL- HEMATOPOIETIC
AMINOMONO- SYSTEM
METHYL)PHENOL EYES
NAME SPECIES TEST RESULT EXPOSURE DURATION
TRIS(2,4,6- RAT NOAEL: 125 MG/KG/DAY 28 DAYS
DIMETHYL-
AMINOMONO-
METHYL)PHENOL
TRIS(2,4,6- RAT NOAEL: 125 MG/KG/DAY 28 DAYS
DIMETHYL-
AMINOMONO-
METHYL)PHENOL
ASPIRATION HAZARD:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH THE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
DISPOSE OF WASTE PRODUCT IN A PERMITTED INDUSTRIAL WASTE FACILITY. AS
A DISPOSAL ALTERNATIVE, INCINERATE IN A PERMITTED WASTE INCINERATION
FACILITY. PROPER DESTRUCTION MAY REQUIRE THE USE OF ADDITIONAL FUEL
DURING INCINERATION PROCESSES. EMPTY DRUMS/BARRELS/CONTAINERS USED FOR
TRANSPORTING AND HANDLING HAZARDOUS CHEMICALS (CHEMICAL SUBSTANCES/
MIXTURES/PREPARATIONS CLASSIFIED AS HAZARDOUS AS PER APPLICABLE
REGULATIONS) SHALL BE CONSIDERED, STORED, TREATED & DISPOSED OF AS
HAZARDOUS WASTES UNLESS OTHERWISE DEFINED BY APPLICABLE WASTE REGULATIONS.
CONSULT WITH THE RESPECTIVE REGULATING AUTHORITIES TO DETERMINE THE
AVAILABLE TREATMENT AND DISPOSAL FACILITIES.
| SECTION 14: TRANSPORT INFORMATION | |
FOR TRANSPORT INFORMATION, PLEASE VISIT:
HTTP://3M.COM/TRANSPORTINFO OR CALL 1-800-364-3577 OR 651-737-6501.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
311/312 HAZARD CATEGORIES:
FIRE HAZARD: NO
PRESSURE HAZARD: NO
REACTIVITY HAZARD: NO
IMMEDIATE HAZARD: YES
DELAYED HAZARD: NO
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
15.3. CHEMICAL INVENTORIES:
THE COMPONENTS OF THIS PRODUCT ARE IN COMPLIANCE WITH THE CHEMICAL
NOTIFICATION REQUIREMENTS OF TSCA.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 3
FLAMMABILITY 1
INSTABILITY 0
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED FOR
USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO INCLUDE
THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT ARE KNOWN
TO BE GENERATED IN SIGNIFICANT QUANTITIES.
HMIS HAZARD CLASSIFICATION:
HEALTH 3
FLAMMABILITY 1
PHYSICAL HAZARD 0
PERSONAL PROTECTION C
HAZARDOUS MATERIAL IDENTIFICATION SYSTEM (HMIS(R*) IV) HAZARD RATINGS ARE
DESIGNED TO INFORM EMPLOYEES OF CHEMICAL HAZARDS IN THE WORKPLACE. THESE
RATINGS ARE BASED ON THE INHERENT PROPERTIES OF THE MATERIAL UNDER EXPECTED
CONDITIONS OF NORMAL USE AND ARE NOT INTENDED FOR USE IN EMERGENCY
SITUATIONS. HMIS(R*) IV RATINGS ARE TO BE USED WITH A FULLY IMPLEMENTED
HMIS(R*) IV PROGRAM. HMIS(R*) IS A REGISTERED MARK OF THE AMERICAN COATINGS
ASSOCIATION (ACA).
DOCUMENT GROUP: 18-2289-9
VERSION NUMBER: 5.00
ISSUE DATE: 02/17/16
SUPERCEDES DATE: 01/21/15
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM
3M(TM) SELF-LEVELING SEAM SEALER PN 08307 PART B (BASE) PN 08307
01/23/15
3M
SAFETY DATA SHEET
COPYRIGHT, 2015, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR
THE PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 18-2290-7
VERSION NUMBER: 4.02
ISSUE DATE: 01/23/15
SUPERCEDES DATE: 02/07/13
| SECTION 1: IDENTIFICATION | |
1.1. PRODUCT IDENTIFIER:
3M(TM) SELF-LEVELING SEAM SEALER PN 08307 PART B (BASE) PN 08307
PRODUCT IDENTIFICATION NUMBERS: LB-K100-0053-0
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE:
AUTOMOTIVE, THIS BASE TO BE USED WITH 3M(TM) SELF-LEVELING SEAM SEALER -
PART A (ACCELERATOR), TWO-PART EPOXY TYPE SELF-LEVELING SEAM SEALER - BASE
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: AUTOMOTIVE AFTERMARKET
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
THE LABEL ELEMENTS BELOW WERE PREPARED IN ACCORDANCE WITH OSHA HAZARD
COMMUNICATION STANDARD, 29 CFR 1910.1200. THIS INFORMATION MAY BE DIFFERENT
FROM THE ACTUAL PRODUCT LABEL INFORMATION FOR LABELS REGULATED BY OTHER
AGENCIES.
2.1. HAZARD CLASSIFICATION
SERIOUS EYE DAMAGE/IRRITATION: CATEGORY 2B.
SKIN SENSITIZER: CATEGORY 1.
2.2. LABEL ELEMENTS:
SIGNAL WORD: WARNING
SYMBOLS: EXCLAMATION MARK
PICTOGRAMS: EXCLAMATION MARK
HAZARD STATEMENTS:
CAUSES EYE IRRITATION.
MAY CAUSE AN ALLERGIC SKIN REACTION.
PRECAUTIONARY STATEMENTS:
GENERAL: KEEP OUT OF REACH OF CHILDREN.
PREVENTION:
AVOID BREATHING DUST/FUME/GAS/MIST/VAPORS/SPRAY.
WEAR PROTECTIVE GLOVES.
WASH THOROUGHLY AFTER HANDLING.
CONTAMINATED WORK CLOTHING MUST NOT BE ALLOWED OUT OF THE WORKPLACE.
RESPONSE:
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES, IF
PRESENT AND EASY TO DO.
CONTINUE RINSING.
IF EYE IRRITATION PERSISTS: GET MEDICAL ADVICE/ATTENTION.
IF ON SKIN: WASH WITH PLENTY OF SOAP AND WATER.
IF SKIN IRRITATION OR RASH OCCURS: GET MEDICAL ADVICE/ATTENTION.
WASH CONTAMINATED CLOTHING BEFORE REUSE.
DISPOSAL:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH APPLICABLE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
2.3. HAZARDS NOT OTHERWISE CLASSIFIED: NONE.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
BISPHENOL A-EPICLOROHYDRIN 25068-38-6 50 - 90 TRADE SECRET *
EPOXY RESIN
EPICHLOROHYDRIN CASTOR OIL 74398-71-3 10 - 30 TRADE SECRET *
BASED EPOXY RESIN
DIMETHYL SILOXANE, REACTION 67762-90-7 0.5 - 1.5 TRADE SECRET *
PRODUCT WITH SILICA
EPICHLOROHYDRIN 106-89-8 <0.02 TRADE SECRET *
*THE SPECIFIC CHEMICAL IDENTITY AND/OR EXACT PERCENTAGE (CONCENTRATION) OF
THIS COMPOSITION HAS BEEN WITHHELD AS A TRADE SECRET.
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
IMMEDIATELY WASH WITH SOAP AND WATER. REMOVE CONTAMINATED CLOTHING AND
WASH BEFORE REUSE. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL ATTENTION.
EYE CONTACT:
FLUSH WITH LARGE AMOUNTS OF WATER. REMOVE CONTACT LENSES IF EASY TO DO.
CONTINUE RINSING. IF SIGNS/SYMPTOMS PERSIST, GET MEDICAL ATTENTION.
IF SWALLOWED:
RINSE MOUTH. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED: NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
IN CASE OF FIRE:
USE A FIRE FIGHTING AGENT SUITABLE FOR ORDINARY COMBUSTIBLE MATERIAL
SUCH AS WATER OR FOAM TO EXTINGUISH.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
NONE INHERENT IN THIS PRODUCT.
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
NO SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS ARE ANTICIPATED.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
EVACUATE AREA. VENTILATE THE AREA WITH FRESH AIR. FOR LARGE SPILL, OR
SPILLS IN CONFINED SPACES, PROVIDE MECHANICAL VENTILATION TO DISPERSE OR
EXHAUST VAPORS, IN ACCORDANCE WITH GOOD INDUSTRIAL HYGIENE PRACTICE.
WARNING!
A MOTOR COULD BE AN IGNITION SOURCE AND COULD CAUSE FLAMMABLE GASES OR
VAPORS IN THE SPILL AREA TO BURN OR EXPLODE. REFER TO OTHER SECTIONS OF
THIS SDS FOR INFORMATION REGARDING PHYSICAL AND HEALTH HAZARDS, RESPIRATORY
PROTECTION, VENTILATION, AND PERSONAL PROTECTIVE EQUIPMENT.
6.2. ENVIRONMENTAL PRECAUTIONS: AVOID RELEASE TO THE ENVIRONMENT.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP:
CONTAIN SPILL. WORKING FROM AROUND THE EDGES OF THE SPILL INWARD, COVER
WITH BENTONITE, VERMICULITE, OR COMMERCIALLY AVAILABLE INORGANIC ABSORBENT
MATERIAL. MIX IN SUFFICIENT ABSORBENT UNTIL IT APPEARS DRY. REMEMBER,
ADDING AN ABSORBENT MATERIAL DOES NOT REMOVE A PHYSICAL, HEALTH, OR
ENVIRONMENTAL HAZARD. COLLECT AS MUCH OF THE SPILLED MATERIAL AS POSSIBLE.
PLACE IN A CLOSED CONTAINER APPROVED FOR TRANSPORTATION BY APPROPRIATE
AUTHORITIES. CLEAN UP RESIDUE WITH AN APPROPRIATE SOLVENT SELECTED BY A
QUALIFIED AND AUTHORIZED PERSON. VENTILATE THE AREA WITH FRESH AIR. READ
AND FOLLOW SAFETY PRECAUTIONS ON THE SOLVENT LABEL AND SDS. SEAL THE
CONTAINER. DISPOSE OF COLLECTED MATERIAL AS SOON AS POSSIBLE.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
AVOID BREATHING OF DUST CREATED BY CUTTING, SANDING, GRINDING OR MACHINING.
KEEP OUT OF REACH OF CHILDREN. AVOID BREATHING DUST/FUME/GAS/MIST/
VAPORS/SPRAY. DO NOT GET IN EYES, ON SKIN, OR ON CLOTHING. DO NOT EAT,
DRINK OR SMOKE WHEN USING THIS PRODUCT. WASH THOROUGHLY AFTER HANDLING.
CONTAMINATED WORK CLOTHING SHOULD NOT BE ALLOWED OUT OF THE WORKPLACE.
AVOID RELEASE TO THE ENVIRONMENT. WASH CONTAMINATED CLOTHING BEFORE REUSE.
AVOID CONTACT WITH OXIDIZING AGENTS (EG. CHLORINE, CHROMIC ACID ETC.)
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
STORE AWAY FROM ACIDS. STORE AWAY FROM OXIDIZING AGENTS. STORE AWAY FROM
AMINES.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN THE TABLE
BELOW, AN OCCUPATIONAL EXPOSURE LIMIT IS NOT AVAILABLE FOR THE COMPONENT.
INGREDIENT C.A.S. NO. AGENCY LIMIT TYPE ADDITIONAL COMMENTS
EPICHLOROHYDRIN 106-89-8 ACGIH TWA: A3:
0.5 PPM CONFIRMED ANIMAL
CARCIN., SKIN
NOTATION
EPICHLOROHYDRIN 106-89-8 OSHA TWA: SKIN NOTATION
19 MG/M3
(5 PPM)
DIMETHYL SILOXANE, 67762-90-7 CMRG CEIL:
REACTION PRODUCT 5 MG/M3
WITH SILICA
SILICA, AMORPHOUS 67762-90-7 OSHA TWA
CONCENTRATION:
0.8 MG/M3
TWA:
20 MILLIONS
OF PARTICLES/
CU. FT.
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
AIHA: AMERICAN INDUSTRIAL HYGIENE ASSOCIATION
CMRG: CHEMICAL MANUFACTURER'S RECOMMENDED GUIDELINES
OSHA:
UNITED STATES DEPARTMENT OF LABOR - OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION
TWA: TIME-WEIGHTED-AVERAGE
STEL: SHORT TERM EXPOSURE LIMIT
CEIL: CEILING
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS
USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO
CONTROL AIRBORNE EXPOSURES TO BELOW RELEVANT EXPOSURE LIMITS AND/OR CONTROL
DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS NOT ADEQUATE, USE
RESPIRATORY PROTECTION EQUIPMENT.
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON THE RESULTS
OF AN EXPOSURE ASSESSMENT.
THE FOLLOWING EYE/FACE PROTECTION(S) ARE RECOMMENDED:
INDIRECT VENTED GOGGLES
SKIN/HAND PROTECTION:
SELECT AND USE GLOVES AND/OR PROTECTIVE CLOTHING APPROVED TO RELEVANT LOCAL
STANDARDS TO PREVENT SKIN CONTACT BASED ON THE RESULTS OF AN EXPOSURE
ASSESSMENT. SELECTION SHOULD BE BASED ON USE FACTORS SUCH AS EXPOSURE
LEVELS, CONCENTRATION OF THE SUBSTANCE OR MIXTURE, FREQUENCY AND DURATION,
PHYSICAL CHALLENGES SUCH AS TEMPERATURE EXTREMES, AND OTHER USE CONDITIONS.
CONSULT WITH YOUR GLOVE AND/OR PROTECTIVE CLOTHING MANUFACTURER FOR
SELECTION OF APPROPRIATE COMPATIBLE GLOVES/PROTECTIVE CLOTHING.
GLOVES MADE FROM THE FOLLOWING MATERIAL(S) ARE RECOMMENDED:
NEOPRENE
NITRILE RUBBER
IF THIS PRODUCT IS USED IN A MANNER THAT PRESENTS A HIGHER POTENTIAL FOR
EXPOSURE (EG. SPRAYING, HIGH SPLASH POTENTIAL ETC.), THEN USE OF PROTECTIVE
COVERALLS MAY BE NECESSARY. SELECT AND USE BODY PROTECTION TO PREVENT
CONTACT BASED ON THE RESULTS OF AN EXPOSURE ASSESSMENT.
THE FOLLOWING PROTECTIVE CLOTHING MATERIAL(S) ARE RECOMMENDED:
APRON - NEOPRENE
RESPIRATORY PROTECTION:
AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF A RESPIRATOR IS REQUIRED.
IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS PART OF A FULL RESPIRATORY
PROTECTION PROGRAM.
BASED ON THE RESULTS OF THE EXPOSURE ASSESSMENT, SELECT FROM THE FOLLOWING
RESPIRATOR TYPE(S) TO REDUCE INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
ORGANIC VAPORS AND PARTICULATES
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: LIQUID
SPECIFIC PHYSICAL FORM: VISCOUS
ODOR, COLOR, GRADE: CLEAR VISCOUS LIQUID, SLIGHT ODOR
ODOR THRESHOLD: NO DATA AVAILABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: >=200 DEG. F
FLASH POINT: >=200 DEG. F [TEST METHOD: CLOSED CUP]
EVAPORATION RATE: NO DATA AVAILABLE
FLAMMABILITY (SOLID, GAS): NOT APPLICABLE
FLAMMABLE LIMITS (LEL): NO DATA AVAILABLE
FLAMMABLE LIMITS (UEL): NO DATA AVAILABLE
VAPOR PRESSURE: <=27 PSIA
VAPOR DENSITY: NO DATA AVAILABLE
DENSITY: 1.17 G/ML
SPECIFIC GRAVITY: 1.17 [REF STD: WATER=1]
SOLUBILITY IN WATER: NIL
SOLUBILITY- NON-WATER: NO DATA AVAILABLE
PARTITION COEFFICIENT N-OCTANOL/WATER: NO DATA AVAILABLE
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
DECOMPOSITION TEMPERATURE: NO DATA AVAILABLE
VISCOSITY: 5,000 - 15,000 CENTIPOISE [TEST METHOD: BROOKFIELD]
HAZARDOUS AIR POLLUTANTS:
0.014 LB HAPS/LB SOLIDS [TEST METHOD: CALCULATED]
VOLATILE ORGANIC COMPOUNDS:
1 G/L [TEST METHOD: CALCULATED SCAQMD RULE 443.1]
VOLATILE ORGANIC COMPOUNDS:
0.1% WEIGHT [TEST METHOD: CALCULATED PER CARB TITLE 2]
VOC LESS H2O & EXEMPT SOLVENTS:
1 G/L [TEST METHOD: CALCULATED SCAQMD RULE 443.1]
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL MAY BE REACTIVE WITH CERTAIN AGENTS UNDER CERTAIN
CONDITIONS - SEE THE REMAINING HEADINGS IN THIS SECTION.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID: NOT DETERMINED
10.5. INCOMPATIBLE MATERIALS:
STRONG OXIDIZING AGENTS
AMINES
STRONG ACIDS
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
ALDEHYDES NOT SPECIFIED
CARBON MONOXIDE NOT SPECIFIED
CARBON DIOXIDE NOT SPECIFIED
TOXIC VAPOR, GAS, PARTICULATE NOT SPECIFIED
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR THE
SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT BELOW
THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
VAPORS RELEASED DURING CURING MAY CAUSE IRRITATION OF THE RESPIRATORY
SYSTEM. SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL DISCHARGE,
HEADACHE, HOARSENESS, AND NOSE AND THROAT PAIN.
SKIN CONTACT:
MILD SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE LOCALIZED REDNESS, SWELLING, ITCHING, AND
DRYNESS.
ALLERGIC SKIN REACTION (NON-PHOTO INDUCED):
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, BLISTERING, AND ITCHING.
EYE CONTACT:
MODERATE EYE IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND BLURRED
OR HAZY VISION.
INGESTION:
GASTROINTESTINAL IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABDOMINAL PAIN, STOMACH UPSET, NAUSEA, VOMITING
AND DIARRHEA.
CARCINOGENICITY:
INGREDIENT CAS NO. CLASS DESCRIPTION REGULATION
EPICHLOROHYDRIN 106-89-8 GRP. 2A: INTERNATIONAL AGENCY
PROBABLE HUMAN CARC. FOR RESEARCH ON CANCER
EPICHLOROHYDRIN 106-89-8 ANTICIPATED HUMAN NATIONAL TOXICOLOGY
CARCINOGEN PROGRAM CARCINOGENS
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT INGESTION NO DATA AVAILABLE;
CALCULATED ATE:
>5,000 MG/KG
BISPHENOL A-EPICLOROHYDRIN DERMAL RAT LD50: >1,600 MG/KG
EPOXY RESIN
BISPHENOL A-EPICLOROHYDRIN INGESTION RAT LD50: >1,000 MG/KG
EPOXY RESIN
EPICHLOROHYDRIN CASTOR OIL DERMAL RABBIT LD50: >2,000 MG/KG
BASED EPOXY RESIN
EPICHLOROHYDRIN CASTOR OIL INGESTION RAT LD50: >5,000 MG/KG
BASED EPOXY RESIN
DIMETHYL SILOXANE, REACTION DERMAL RABBIT LD50: >5,000 MG/KG
PRODUCT WITH SILICA
DIMETHYL SILOXANE, REACTION INHALATION- RAT LC50: >0.691 MG/L
PRODUCT WITH SILICA DUST/MIST
(4 HOURS)
DIMETHYL SILOXANE, REACTION INGESTION RAT LD50: > 5,110 MG/KG
PRODUCT WITH SILICA
EPICHLOROHYDRIN DERMAL RABBIT LD50: 755 MG/KG
EPICHLOROHYDRIN INHALATION- RAT LC50: 1.7 MG/L
VAPOR
(4 HOURS)
EPICHLOROHYDRIN INGESTION RAT LD50: 260 MG/KG
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
BISPHENOL A-EPICLOROHYDRIN EPOXY RESIN RABBIT MILD IRRITANT
DIMETHYL SILOXANE, REACTION PRODUCT RABBIT NO SIGNIFICANT
WITH SILICA IRRITATION
EPICHLOROHYDRIN HUMAN AND CORROSIVE
ANIMAL
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
BISPHENOL A-EPICLOROHYDRIN EPOXY RESIN RABBIT MODERATE IRRITANT
DIMETHYL SILOXANE, REACTION PRODUCT RABBIT NO SIGNIFICANT
WITH SILICA IRRITATION
EPICHLOROHYDRIN RABBIT CORROSIVE
SKIN SENSITIZATION:
NAME SPECIES VALUE
BISPHENOL A-EPICLOROHYDRIN HUMAN AND ANIMAL SENSITIZING
EPOXY RESIN
DIMETHYL SILOXANE, REACTION HUMAN AND ANIMAL NOT SENSITIZING
PRODUCT WITH SILICA
EPICHLOROHYDRIN HUMAN AND ANIMAL SENSITIZING
RESPIRATORY SENSITIZATION:
NAME SPECIES VALUE
BISPHENOL A-EPICLOROHYDRIN HUMAN SOME POSITIVE DATA EXIST, BUT
EPOXY RESIN THE DATA ARE NOT SUFFICIENT
FOR CLASSIFICATION
GERM CELL MUTAGENICITY
NAME ROUTE VALUE
BISPHENOL A-EPICLOROHYDRIN IN VIVO NOT MUTAGENIC
EPOXY RESIN
BISPHENOL A-EPICLOROHYDRIN IN VITRO SOME POSITIVE DATA EXIST, BUT
EPOXY RESIN THE DATA ARE NOT SUFFICIENT
FOR CLASSIFICATION
DIMETHYL SILOXANE, REACTION IN VITRO NOT MUTAGENIC
PRODUCT WITH SILICA
EPICHLOROHYDRIN IN VITRO SOME POSITIVE DATA EXIST, BUT
THE DATA ARE NOT SUFFICIENT
FOR CLASSIFICATION
EPICHLOROHYDRIN IN VIVO MUTAGENIC
CARCINOGENICITY:
NAME ROUTE SPECIES VALUE
BISPHENOL A-EPICLOROHYDRIN DERMAL MOUSE SOME POSITIVE DATA
EPOXY RESIN EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
DIMETHYL SILOXANE, REACTION NOT MOUSE SOME POSITIVE DATA
PRODUCT WITH SILICA SPECIFIED EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
EPICHLOROHYDRIN DERMAL MOUSE NOT CARCINOGENIC
EPICHLOROHYDRIN INGESTION RAT CARCINOGENIC
EPICHLOROHYDRIN INHALATION RAT CARCINOGENIC
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
NAME ROUTE VALUE
BISPHENOL A-EPICLOROHYDRIN INGESTION NOT TOXIC TO FEMALE REPRODUCTION
EPOXY RESIN
BISPHENOL A-EPICLOROHYDRIN INGESTION NOT TOXIC TO MALE REPRODUCTION
EPOXY RESIN
BISPHENOL A-EPICLOROHYDRIN DERMAL NOT TOXIC TO DEVELOPMENT
EPOXY RESIN
BISPHENOL A-EPICLOROHYDRIN INGESTION NOT TOXIC TO DEVELOPMENT
EPOXY RESIN
DIMETHYL SILOXANE, REACTION INGESTION NOT TOXIC TO FEMALE REPRODUCTION
PRODUCT WITH SILICA
DIMETHYL SILOXANE, REACTION INGESTION NOT TOXIC TO MALE REPRODUCTION
PRODUCT WITH SILICA
DIMETHYL SILOXANE, REACTION INGESTION NOT TOXIC TO DEVELOPMENT
PRODUCT WITH SILICA
EPICHLOROHYDRIN INHALATION NOT TOXIC TO FEMALE REPRODUCTION
EPICHLOROHYDRIN INHALATION NOT TOXIC TO DEVELOPMENT
EPICHLOROHYDRIN INGESTION SOME POSITIVE DEVELOPMENTAL DATA
EXIST, BUT THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION
EPICHLOROHYDRIN INGESTION TOXIC TO MALE REPRODUCTION
EPICHLOROHYDRIN INHALATION TOXIC TO MALE REPRODUCTION
NAME SPECIES TEST RESULT EXPOSURE DURATION
BISPHENOL A-EPICLOROHYDRIN RAT NOAEL: 2 GENERATION
EPOXY RESIN 750 MG/KG/DAY
BISPHENOL A-EPICLOROHYDRIN RAT NOAEL: 2 GENERATION
EPOXY RESIN 750 MG/KG/DAY
BISPHENOL A-EPICLOROHYDRIN RABBIT NOAEL: DURING
EPOXY RESIN 300 MG/KG/DAY ORGANOGENESIS
BISPHENOL A-EPICLOROHYDRIN RAT NOAEL: 2 GENERATION
EPOXY RESIN 750 MG/KG/DAY
DIMETHYL SILOXANE, REACTION RAT NOAEL: 1 GENERATION
PRODUCT WITH SILICA 509 MG/KG/DAY
DIMETHYL SILOXANE, REACTION RAT NOAEL: 1 GENERATION
PRODUCT WITH SILICA 497 MG/KG/DAY
DIMETHYL SILOXANE, REACTION RAT NOAEL: DURING
PRODUCT WITH SILICA 1,350 MG/KG/DAY ORGANOGENESIS
EPICHLOROHYDRIN RAT NOAEL: 0.2 MG/L 10 WEEKS
EPICHLOROHYDRIN MULTIPLE NOAEL: 0.09 MG/L DURING
ANIMAL ORGANOGENESIS
SPECIES
EPICHLOROHYDRIN MULTIPLE NOAEL: DURING GESTATION
ANIMAL 160 MG/KG/DAY
SPECIES
EPICHLOROHYDRIN RAT LOAEL: 23 DAYS
6.25 MG/KG/DAY
EPICHLOROHYDRIN RAT NOAEL: 0.02 MG/L 10 WEEKS
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
EPICHLOROHYDRIN INHALATION RESPIRATORY MAY CAUSE RESPIRATORY
IRRITATION IRRITATION
EPICHLOROHYDRIN INHALATION LIVER SOME POSITIVE DATA
EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
NAME SPECIES TEST RESULT EXPOSURE DURATION
EPICHLOROHYDRIN HUMAN NOAEL: OCCUPATIONAL EXPOSURE
NOT AVAILABLE
EPICHLOROHYDRIN HUMAN NOAEL: OCCUPATIONAL EXPOSURE
NOT AVAILABLE
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
BISPHENOL A- DERMAL LIVER SOME POSITIVE DATA EXIST,
EPICLOROHYDRIN BUT THE DATA ARE NOT
EPOXY RESIN SUFFICIENT FOR
CLASSIFICATION
BISPHENOL A- DERMAL NERVOUS ALL DATA ARE NEGATIVE
EPICLOROHYDRIN SYSTEM
EPOXY RESIN
BISPHENOL A- INGESTION AUDITORY ALL DATA ARE NEGATIVE
EPICLOROHYDRIN SYSTEM
EPOXY RESIN HEART
ENDOCRINE
SYSTEM
HEMATOPOIETIC
SYSTEM
LIVER
EYES
KIDNEY AND/OR
BLADDER
DIMETHYL INHALATION RESPIRATORY ALL DATA ARE NEGATIVE
SILOXANE, SYSTEM
REACTION SILICOSIS
PRODUCT
WITH SILICA
EPICHLOROHYDRIN INHALATION LIVER CAUSES DAMAGE TO ORGANS
THROUGH PROLONGED OR
REPEATED EXPOSURE
EPICHLOROHYDRIN INHALATION KIDNEY MAY CAUSE DAMAGE TO
AND/OR ORGANS THOUGH PROLONGED
BLADDER OR REPEATED EXPOSURE
EPICHLOROHYDRIN INHALATION ENDOCRINE SOME POSITIVE DATA EXIST,
SYSTEM BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
EPICHLOROHYDRIN INHALATION IMMUNE SOME POSITIVE DATA EXIST,
SYSTEM BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
EPICHLOROHYDRIN INHALATION HEART SOME POSITIVE DATA EXIST,
BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
EPICHLOROHYDRIN INHALATION NERVOUS SOME POSITIVE DATA EXIST,
SYSTEM BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
EPICHLOROHYDRIN INHALATION RESPIRATORY SOME POSITIVE DATA EXIST,
SYSTEM BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
EPICHLOROHYDRIN INHALATION BLOOD ALL DATA ARE NEGATIVE
EPICHLOROHYDRIN INGESTION HEART SOME POSITIVE DATA EXIST,
BLOOD BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
EPICHLOROHYDRIN INGESTION LIVER SOME POSITIVE DATA EXIST,
BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
NAME SPECIES TEST RESULT EXPOSURE DURATION
BISPHENOL A- RAT NOAEL: 2 YEARS
EPICLOROHYDRIN 1,000 MG/KG/DAY
EPOXY RESIN
BISPHENOL A- RAT NOAEL: 13 WEEKS
EPICLOROHYDRIN 1,000 MG/KG/DAY
EPOXY RESIN
BISPHENOL A- RAT NOAEL: 28 DAYS
EPICLOROHYDRIN 1,000 MG/KG/DAY
EPOXY RESIN
DIMETHYL HUMAN NOAEL: OCCUPATIONAL EXPOSURE
SILOXANE, NOT AVAILABLE
REACTION PRODUCT
WITH SILICA
EPICHLOROHYDRIN RAT NOAEL: 0.21 MG/L 19 DAYS
EPICHLOROHYDRIN RAT NOAEL: 0.04 MG/L 136 WEEKS
EPICHLOROHYDRIN RAT NOAEL: 0.377 MG/L 4 WEEKS
EPICHLOROHYDRIN RAT LOAEL: 0.211 MG/L 4 WEEKS
EPICHLOROHYDRIN RAT NOAEL: 0.02 MG/L 98 DAYS
EPICHLOROHYDRIN RAT NOAEL: .002 MG/L 98 DAYS
EPICHLOROHYDRIN MULTIPLE NOAEL: 0.02 MG/L 13 WEEKS
ANIMAL
SPECIES
EPICHLOROHYDRIN RAT NOAEL: 0.189 MG/L 90 DAYS
EPICHLOROHYDRIN RAT NOAEL: 80 MG/KG/DAY 12 WEEKS
EPICHLOROHYDRIN RAT NOAEL: 25 MG/KG/DAY 90 DAYS
ASPIRATION HAZARD:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/ CONTAINER IN ACCORDANCE WITH THE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
INCINERATE IN A PERMITTED WASTE INCINERATION FACILITY. PROPER DESTRUCTION
MAY REQUIRE THE USE OF ADDITIONAL FUEL DURING INCINERATION PROCESSES. EMPTY
DRUMS/BARRELS/CONTAINERS USED FOR TRANSPORTING AND HANDLING HAZARDOUS
CHEMICALS (CHEMICAL SUBSTANCES/MIXTURES/PREPARATIONS CLASSIFIED AS
HAZARDOUS AS PER APPLICABLE REGULATIONS) SHALL BE CONSIDERED, STORED,
TREATED & DISPOSED OF AS HAZARDOUS WASTES UNLESS OTHERWISE DEFINED BY
APPLICABLE WASTE REGULATIONS. CONSULT WITH THE RESPECTIVE REGULATING
AUTHORITIES TO DETERMINE THE AVAILABLE TREATMENT AND DISPOSAL FACILITIES.
| SECTION 14: TRANSPORT INFORMATION | |
TRANSPORT INFORMATION, PLEASE VISIT:
HTTP://3M.COM/TRANSPORTINFO OR CALL 1-800-364-3577 OR 651-737-6501.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
311/312 HAZARD CATEGORIES:
FIRE HAZARD: NO
PRESSURE HAZARD: NO
REACTIVITY HAZARD: YES
IMMEDIATE HAZARD: YES
DELAYED HAZARD: YES
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
CALIFORNIA PROPOSITION 65:
INGREDIENT C.A.S. NO. CLASSIFICATION
EPICHLOROHYDRIN 106-89-8 MALE REPRODUCTIVE TOXIN
EPICHLOROHYDRIN 106-89-8 CARCINOGEN
WARNING:
THIS PRODUCT CONTAINS A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WARNING:
THIS PRODUCT CONTAINS A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE
CANCER.
15.3. CHEMICAL INVENTORIES:
THE COMPONENTS OF THIS PRODUCT ARE IN COMPLIANCE WITH THE CHEMICAL
NOTIFICATION REQUIREMENTS OF TSCA.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 2
FLAMMABILITY 1
INSTABILITY 1
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED
FOR USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO INCLUDE
THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT ARE KNOWN
TO BE GENERATED IN SIGNIFICANT QUANTITIES.
DOCUMENT GROUP: 18-2290-7
VERSION NUMBER: 4.02
ISSUE DATE: 01/23/15
SUPERCEDES DATE: 02/07/13
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM