| Common Name: | STANDARD ABRASIVES PRODUCT, PRIVATE LABEL ZA 2PLY SAIT HZH QUICK CHANGE |
| Manufacturer: | 3M |
| SDS Revision Date: | 7/28/2014 |
| SDS Format: | GHS-US |
| Item Number(s): | 30CN79 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
STANDARD ABRASIVES(TM) PRODUCT, PRIVATE LABEL ZA 2PLY SAIT HZH QUICK CHANGE
07/28/14
SA
STANDARD ABRASIVES(TM)
SAFETY DATA SHEET
COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR THE PURPOSE OF PROPERLY
UTILIZING STANDARD ABRASIVES PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM THE MANUFACTURER, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 28-9965-6
VERSION NUMBER: 1.01
ISSUE DATE: 07/28/14
SUPERCEDES DATE: 12/10/10
| SECTION 1: IDENTIFICATION |  |
1.1. PRODUCT IDENTIFIER:
STANDARD ABRASIVES(TM) PRODUCT, PRIVATE LABEL ZA 2PLY SAIT HZH QUICK CHANGE
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE: ABRASIVE PRODUCT
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: ABRASIVE SYSTEMS DIVISION
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
NOT CLASSIFIED AS HAZARDOUS ACCORDING TO OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
2.2. LABEL ELEMENTS:
SIGNAL WORD: NOT APPLICABLE.
SYMBOLS: NOT APPLICABLE.
PICTOGRAMS: NOT APPLICABLE.
2.3. HAZARDS NOT OTHERWISE CLASSIFIED: NONE.
21% OF THE MIXTURE CONSISTS OF INGREDIENTS OF UNKNOWN ACUTE ORAL TOXICITY.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
ZIRCONIUM OXIDE MINERAL 1314-23-4 10 - 25
ALUMINUM OXIDE MINERAL (NON-FIBROUS) 1344-28-1 10 - 20
INORGANIC FLUORIDE 15096-52-3 5 - 10
FILLER 1317-65-3 2 - 10
CURED RESIN MIXTURE 5 - 25
CLOTH BACKINGS MIXTURE 20 - 55
QUICK CHANGE ATTACHMENT MIXTURE 3 - 5
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
WASH WITH SOAP AND WATER. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL ATTENTION.
EYE CONTACT:
FLUSH WITH LARGE AMOUNTS OF WATER. REMOVE CONTACT LENSES IF EASY TO DO.
CONTINUE RINSING. IF SIGNS/SYMPTOMS PERSIST, GET MEDICAL ATTENTION.
IF SWALLOWED: NO NEED FOR FIRST AID IS ANTICIPATED.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED: NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
IN CASE OF FIRE:
USE A FIRE FIGHTING AGENT SUITABLE FOR ORDINARY COMBUSTIBLE MATERIAL
SUCH AS WATER OR FOAM TO EXTINGUISH.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
NONE INHERENT IN THIS PRODUCT.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
NO SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS ARE ANTICIPATED.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
OBSERVE PRECAUTIONS FROM OTHER SECTIONS.
6.2. ENVIRONMENTAL PRECAUTIONS: AVOID RELEASE TO THE ENVIRONMENT.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP: NOT APPLICABLE.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
FOR INDUSTRIAL OR PROFESSIONAL USE ONLY. AVOID BREATHING OF DUST CREATED
BY SANDING, GRINDING OR MACHINING. DAMAGED PRODUCT CAN BREAK APART DURING
USE AND CAUSE SERIOUS INJURY TO FACE OR EYES. CHECK PRODUCT FOR DAMAGE
SUCH AS CRACKS OR NICKS PRIOR TO USE. REPLACE IF DAMAGED. ALWAYS WEAR EYE
AND FACE PROTECTION WHEN WORKING AT SANDING OR GRINDING OPERATIONS OR WHEN
NEAR SUCH OPERATIONS. AVOID RELEASE TO THE ENVIRONMENT. COMBUSTIBLE DUST
MAY FORM BY ACTION OF THIS PRODUCT ON ANOTHER MATERIAL (SUBSTRATE). DUST
GENERATED FROM THE SUBSTRATE DURING USE OF THIS PRODUCT MAY BE EXPLOSIVE
IF IN SUFFICIENT CONCENTRATION WITH AN IGNITION SOURCE. DUST DEPOSITS
SHOULD NOT BE ALLOWED TO ACCUMULATE ON SURFACES BECAUSE OF THE POTENTIAL
FOR SECONDARY EXPLOSIONS.
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
NO SPECIAL STORAGE REQUIREMENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
INGREDIENT C.A.S. NO. AGENCY LIMIT TYPE ADDITIONAL
COMMENTS
ZIRCONIUM COMPOUNDS 1314-23-4 ACGIH TWA(AS Zr): A4:
5 MG/M3 NOT CLASS.
AS HUMAN
STEL(AS Zr): CARCIN
10 MG/M3
ZIRCONIUM COMPOUNDS 1314-23-4 OSHA TWA(AS Zr):
5 MG/M3
FILLER 1317-65-3 OSHA TWA(AS TOTAL
DUST):
15 MG/M3
TWA(RESPIRABLE
FRACTION):
5 MG/M3
ALUMINUM OXIDE 1344-28-1 CMRG TWA: 1 FIBER/CC
MINERAL (NON-
FIBROUS)
ALUMINUM OXIDE 1344-28-1 OSHA TWA(AS TOTAL
MINERAL (NON- DUST):
FIBROUS) 15 MG/M3
TWA(RESPIRABLE
FRACTION):
5 MG/M3
ALUMINUM, INSOLUBLE 1344-28-1 ACGIH TWA(RESPIRABLE A4:
COMPOUNDS FRACTION): NOT CLASS.
1 MG/M3 AS HUMAN
CARCIN
ALUMINUM, INSOLUBLE 15096-52-3 ACGIH TWA(RESPIRABLE A4:
COMPOUNDS FRACTION): NOT CLASS.
1 MG/M3 AS HUMAN
CARCIN
FLUORIDES 15096-52-3 ACGIH TWA(AS F): A4:
2.5 MG/M3 NOT CLASS.
AS HUMAN
CARCIN
FLUORIDES 15096-52-3 OSHA TWA(AS DUST):
2.5 MG/M3
TWA(AS F):
2.5 MG/M3
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
AIHA: AMERICAN INDUSTRIAL HYGIENE ASSOCIATION
CMRG: CHEMICAL MANUFACTURER'S RECOMMENDED GUIDELINES
OSHA:
UNITED STATES DEPARTMENT OF LABOR - OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION
TWA: TIME-WEIGHTED-AVERAGE
STEL: SHORT TERM EXPOSURE LIMIT
CEIL: CEILING
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
PROVIDE APPROPRIATE LOCAL EXHAUST VENTILATION FOR SANDING, GRINDING OR
MACHINING. USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST
VENTILATION TO CONTROL AIRBORNE EXPOSURES TO BELOW RELEVANT EXPOSURE
LIMITS AND/OR CONTROL DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS
NOT ADEQUATE, USE RESPIRATORY PROTECTION EQUIPMENT. PROVIDE LOCAL EXHAUST
AT PROCESS EMISSION SOURCES TO CONTROL EXPOSURE NEAR THE SOURCE AND TO
PREVENT THE ESCAPE OF DUST INTO THE WORK AREA. ENSURE THAT DUST-HANDLING
SYSTEMS (SUCH AS EXHAUST DUCTS, DUST COLLECTORS, VESSELS, AND PROCESSING
EQUIPMENT) ARE DESIGNED IN A MANNER TO PREVENT THE ESCAPE OF DUST INTO
THE WORK AREA (I.E., THERE IS NO LEAKAGE FROM THE EQUIPMENT).
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
TO MINIMIZE THE RISK OF INJURY TO FACE AND EYES, ALWAYS WEAR EYE AND FACE
PROTECTION WHEN WORKING AT SANDING OR GRINDING OPERATIONS OR WHEN NEAR
SUCH OPERATIONS. SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT
BASED ON THE RESULTS OF AN EXPOSURE ASSESSMENT.
THE FOLLOWING EYE/FACE PROTECTION(S) ARE RECOMMENDED:
SAFETY GLASSES WITH SIDE SHIELDS
SKIN/HAND PROTECTION:
WEAR APPROPRIATE GLOVES TO MINIMIZE RISK OF INJURY TO SKIN FROM CONTACT
WITH DUST OR PHYSICAL ABRASION FROM GRINDING OR SANDING.
RESPIRATORY PROTECTION:
ASSESS EXPOSURE CONCENTRATIONS OF ALL MATERIALS INVOLVED IN THE WORK
PROCESS. CONSIDER MATERIAL BEING ABRADED WHEN DETERMINING THE APPROPRIATE
RESPIRATORY PROTECTION. SELECT AND USE APPROPRIATE RESPIRATORS TO PREVENT
INHALATION OVEREXPOSURE. AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF
A RESPIRATOR IS REQUIRED. IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS
PART OF A FULL RESPIRATORY PROTECTION PROGRAM.
BASED ON THE RESULTS OF THE EXPOSURE ASSESSMENT, SELECT FROM THE FOLLOWING
RESPIRATOR TYPE(S) TO REDUCE INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
PARTICULATES
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: SOLID
ODOR, COLOR, GRADE: SOLID ABRASIVE PRODUCT
ODOR THRESHOLD: NOT APPLICABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: NOT APPLICABLE
FLASH POINT: NOT APPLICABLE
EVAPORATION RATE: NOT APPLICABLE
FLAMMABILITY (SOLID, GAS): NOT CLASSIFIED
FLAMMABLE LIMITS(LEL): NOT APPLICABLE
FLAMMABLE LIMITS(UEL): NOT APPLICABLE
VAPOR PRESSURE: NOT APPLICABLE
VAPOR DENSITY: NOT APPLICABLE
SPECIFIC GRAVITY: NOT APPLICABLE
SOLUBILITY IN WATER: NOT APPLICABLE
SOLUBILITY- NON-WATER: NOT APPLICABLE
PARTITION COEFFICIENT N-OCTANOL/WATER: NOT APPLICABLE
AUTOIGNITION TEMPERATURE: NOT APPLICABLE
DECOMPOSITION TEMPERATURE: NOT APPLICABLE
VISCOSITY: NOT APPLICABLE
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL IS CONSIDERED TO BE NON REACTIVE UNDER NORMAL USE CONDITIONS.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID: NONE KNOWN.
10.5. INCOMPATIBLE MATERIALS: NONE KNOWN.
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR
THE SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT
BELOW THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
DUST FROM GRINDING, SANDING OR MACHINING MAY CAUSE IRRITATION OF THE
RESPIRATORY SYSTEM. SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL
DISCHARGE, HEADACHE, HOARSENESS, AND NOSE AND THROAT PAIN.
SKIN CONTACT:
MECHANICAL SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABRASION, REDNESS, PAIN, AND ITCHING.
EYE CONTACT:
MECHANICAL EYE IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE PAIN, REDNESS, TEARING AND CORNEAL ABRASION.
DUST CREATED BY GRINDING, SANDING, OR MACHINING MAY CAUSE EYE IRRITATION.
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND BLURRED
OR HAZY VISION.
INGESTION: NO HEALTH EFFECTS ARE EXPECTED.
ADDITIONAL INFORMATION:
THIS PRODUCT, WHEN USED UNDER REASONABLE CONDITIONS AND IN ACCORDANCE WITH
THE STANDARD ABRASIVES DIRECTIONS FOR USE, SHOULD NOT PRESENT A HEALTH
HAZARD. HOWEVER, USE OR PROCESSING OF THE PRODUCT IN A MANNER NOT IN
ACCORDANCE WITH THE PRODUCT'S DIRECTIONS FOR USE MAY AFFECT THE PERFORMANCE
OF THE PRODUCT AND MAY PRESENT POTENTIAL HEALTH AND SAFETY HAZARDS.
THIS DOCUMENT COVERS ONLY THE STANDARD ABRASIVES PRODUCT. FOR COMPLETE
ASSESSMENT, WHEN DETERMINING THE DEGREE OF HAZARD, THE MATERIAL BEING
ABRADED MUST ALSO BE CONSIDERED.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT INGESTION NO DATA AVAILABLE;
CALCULATED ATE:
>5,000 MG/KG
ZIRCONIUM OXIDE MINERAL INGESTION MOUSE LD50: >8,800 MG/KG
ALUMINUM OXIDE MINERAL DERMAL LD50:
(NON-FIBROUS) ESTIMATED TO BE
>5,000 MG/KG
ALUMINUM OXIDE MINERAL INHALATION- RAT LC50: >2.3 MG/L
(NON-FIBROUS) DUST/MIST
(4 HOURS)
ALUMINUM OXIDE MINERAL INGESTION RAT LD50: >5,000 MG/KG
(NON-FIBROUS)
INORGANIC FLUORIDE DERMAL RABBIT LD50: >2,100 MG/KG
INORGANIC FLUORIDE INHALATION- RAT LC50: 4.5 MG/L
DUST/MIST
(4 HOURS)
INORGANIC FLUORIDE INGESTION RAT LD50: 5,000 MG/KG
FILLER DERMAL RAT LD50: >2,000 MG/KG
FILLER INHALATION- RAT LC50: 3.0 MG/L
DUST/MIST
(4 HOURS)
FILLER INGESTION RAT LD50: 6,450 MG/KG
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
ALUMINUM OXIDE MINERAL RABBIT NO SIGNIFICANT IRRITATION
(NON-FIBROUS)
INORGANIC FLUORIDE MINIMAL IRRITATION
FILLER RABBIT NO SIGNIFICANT IRRITATION
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
ALUMINUM OXIDE MINERAL RABBIT NO SIGNIFICANT IRRITATION
(NON-FIBROUS)
INORGANIC FLUORIDE MODERATE IRRITANT
FILLER RABBIT NO SIGNIFICANT IRRITATION
SKIN SENSITIZATION:
NAME SPECIES VALUE
RESPIRATORY SENSITIZATION:
NAME SPECIES VALUE
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
ALUMINUM OXIDE MINERAL IN VITRO NOT MUTAGENIC
(NON-FIBROUS)
CARCINOGENICITY:
NAME ROUTE SPECIES VALUE
ALUMINUM OXIDE MINERAL INHALATION RAT NOT CARCINOGENIC
(NON-FIBROUS)
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
NAME ROUTE VALUE
FILLER INGESTION NOT TOXIC TO DEVELOPMENT
NAME SPECIES TEST RESULT EXPOSURE DURATION
FILLER RAT NOAEL: 625 MG/KG/DAY PREMATING & DURING GESTATION
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
FILLER INHALATION RESPIRATORY SYSTEM ALL DATA ARE NEGATIVE
NAME SPECIES TEST RESULT EXPOSURE DURATION
FILLER RAT NOAEL: 0.812 MG/L 90 MINUTES
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
ALUMINUM OXIDE MINERAL INHALATION PNEUMOCONIOSIS SOME POSITIVE DATA
(NON-FIBROUS) PULMONARY EXIST, BUT THE
FIBROSIS DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
INORGANIC FLUORIDE INHALATION BONE, TEETH, SOME POSITIVE DATA
NAILS, AND/OR EXIST, BUT THE
HAIR DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
FILLER INHALATION RESPIRATORY SOME POSITIVE DATA
SYSTEM EXIST, BUT THE
DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
NAME SPECIES TEST RESULT EXPOSURE DURATION
ALUMINUM OXIDE MINERAL HUMAN NOAEL: OCCUPATIONAL
(NON-FIBROUS) NOT AVAILABLE EXPOSURE
INORGANIC FLUORIDE HHA
FILLER HUMAN NOAEL: OCCUPATIONAL
NOT AVAILABLE EXPOSURE
ASPIRATION HAZARD:
NAME VALUE
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH THE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
THE SUBSTRATE THAT WAS ABRADED MUST BE CONSIDERED AS A FACTOR IN THE
DISPOSAL METHOD FOR THIS PRODUCT. INCINERATE IN A PERMITTED WASTE
INCINERATION FACILITY. PROPER DESTRUCTION MAY REQUIRE THE USE OF
ADDITIONAL FUEL DURING INCINERATION PROCESSES. AS A DISPOSAL ALTERNATIVE,
UTILIZE AN ACCEPTABLE PERMITTED WASTE DISPOSAL FACILITY.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
| SECTION 14: TRANSPORT INFORMATION | |
NOT REGULATED PER U.S. DOT, IATA OR IMO.
THESE TRANSPORTATION CLASSIFICATIONS ARE PROVIDED AS A CUSTOMER SERVICE.
AS THE SHIPPER YOU REMAIN RESPONSIBLE FOR COMPLYING WITH ALL APPLICABLE
LAWS AND REGULATIONS, INCLUDING PROPER TRANSPORTATION CLASSIFICATION AND
PACKAGING. THE MANUFACTURER'S TRANSPORTATION CLASSIFICATIONS ARE BASED ON
PRODUCT FORMULATION, PACKAGING, THE MANUFACTURER'S POLICIES AND THE
MANUFACTURER'S UNDERSTANDING OF APPLICABLE CURRENT REGULATIONS. THE
MANUFACTURER DOES NOT GUARANTEE THE ACCURACY OF THIS CLASSIFICATION
INFORMATION. THIS INFORMATION APPLIES ONLY TO TRANSPORTATION CLASSIFICATION
AND NOT THE PACKAGING, LABELING, OR MARKING REQUIREMENTS. THE ORIGINAL
STANDARD ABRASIVES PACKAGE IS CERTIFIED FOR U.S. GROUND SHIPMENT ONLY.
IF YOU ARE SHIPPING BY AIR OR OCEAN, THE PACKAGE MAY NOT MEET APPLICABLE
REGULATORY REQUIREMENTS.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS:
CONTACT THE MANUFACTURER FOR MORE INFORMATION.
311/312 HAZARD CATEGORIES:
FIRE HAZARD: NO
PRESSURE HAZARD: NO
REACTIVITY HAZARD: NO
IMMEDIATE HAZARD: NO
DELAYED HAZARD: NO
15.2. STATE REGULATIONS:
CONTACT THE MANUFACTURER FOR MORE INFORMATION.
15.3. CHEMICAL INVENTORIES:
THIS PRODUCT IS AN ARTICLE AS DEFINED BY TSCA REGULATIONS, AND IS EXEMPT
FROM TSCA INVENTORY LISTING REQUIREMENTS.
CONTACT THE MANUFACTURER FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS:
CONTACT THE MANUFACTURER FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 0
FLAMMABILITY 1
INSTABILITY 0
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED
FOR USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO INCLUDE
THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT ARE KNOWN
TO BE GENERATED IN SIGNIFICANT QUANTITIES.
DOCUMENT GROUP: 28-9965-6
VERSION NUMBER: 1.01
ISSUE DATE: 07/28/14
SUPERCEDES DATE: 12/10/10
DISCLAIMER:
THE INFORMATION IN THIS MATERIAL SAFETY DATA SHEET (MSDS) IS BELIEVED TO
BE CORRECT AS OF THE DATE ISSUED. THE MANUFACTURER MAKES NO WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF
PERFORMANCE OR USAGE OF TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER
THE STANDARD ABRASIVES PRODUCT IS FIT FOR A PARTICULAR PURPOSE AND SUITABLE
FOR USER'S METHOD OF USE OR APPLICATION. GIVEN THE VARIETY OF FACTORS THAT
CAN AFFECT THE USE AND APPLICATION OF A STANDARD ABRASIVES PRODUCT, SOME
OF WHICH ARE UNIQUELY WITHIN THE USER'S KNOWLEDGE AND CONTROL, IT IS
ESSENTIAL THAT THE USER EVALUATE THE STANDARD ABRASIVES PRODUCT TO
DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND SUITABLE FOR
USER'S METHOD OF USE OR APPLICATION.
THE MANUFACTURER PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO
ITS CUSTOMERS. DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY
HAVE RESULTED IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, THE
MANUFACTURER MAKES NO REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY.
IN ADDITION, INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT
AS THE INFORMATION IN THE MSDS AVAILABLE DIRECTLY FROM THE MANUFACTURER.
STANDARD ABRASIVES MSDSS ARE AVAILABLE AT WWW.STANDARDABRASIVES.COM
COPYRIGHT, 2014, 3M. ALL RIGHTS RESERVED.