| Common Name: | ENDURANCE MOLD RELEASE |
| Manufacturer: | STONER |
| SDS Revision Date: | 4/2/2015 |
| SDS Format: | GHS-US |
| Item Number(s): | 35HY49 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
STONER
SAFETY DATA SHEET
A353
ENDURANCE(TM) MOLD RELEASE
COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR THE PURPOSE OF PROPERLY
UTILIZING STONER INC. PRODUCT IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR
AGREEMENT IS OBTAINED FROM STONER INC., &
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH INTENTION OF EARNING PROFIT THEREON.
| 1. IDENTIFICATION |  |
STONER INCORPORATED
1070 ROBERT FULTON HWY.
QUARRYVILLE, PA 17566
1-800-227-5538
PRODUCT NAME: ENDURANCE(TM) MOLD RELEASE
PRODUCT CODE: A353
PRODUCT USE: MOLD RELEASE
24-HOUR EMERGENCY PHONE: 1-800-424-9300 [CHEMTREC]
| 2. HAZARD IDENTIFICATION | |
POTENTIAL HEALTH EFFECTS:
CLASSIFICATION OF THE CHEMICAL IN ACCORDANCE WITH PARAGRAPH (D)
OF SUBSECTION 1910.1200;
GHS HAZARD SYMBOLS:
FLAME
GAS CYLINDER
CORROSION
EXCLAMATION MARK
GHS CLASSIFICATION:
GASES UNDER PRESSURE - LIQUIFIED GAS
SERIOUS EYE DAMAGE/EYE IRRITATION CATEGORY 1
FLAMMABLE AEROSOL CATEGORY 2
SKIN CORROSION/IRRITATION CATEGORY 2
SPECIFIC TARGET ORGAN SYSTEMIC TOXICITY (STOT) - SINGLE EXPOSURE CATEGORY 3
SIGNAL WORD: DANGER
HAZARD STATEMENTS:
FLAMMABLE AEROSOL.
CONTAINS GAS UNDER PRESSURE; MAY EXPLODE IF HEATED.
CAUSES SKIN IRRITATION.
CAUSES SERIOUS EYE DAMAGE.
MAY CAUSE RESPIRATORY IRRITATION.
PRECAUTIONARY STATEMENTS:
PREVENTION:
KEEP AWAY FROM HEAT/SPARKS/OPEN FLAMES/HOT SURFACES. - NO SMOKING.
DO NOT SPRAY ON AN OPEN FLAME OR OTHER IGNITION SOURCE.
PRESSURIZED CONTAINER: DO NOT PIERCE OR BURN, EVEN AFTER USE.
AVOID BREATHING DUST/FUME/GAS/MIST/VAPOURS/SPRAY.
WASH THOROUGHLY AFTER HANDLING.
USE ONLY OUTDOORS OR IN A WELL-VENTILATED AREA.
WEAR PROTECTIVE GLOVES/PROTECTIVE CLOTHING/EYE PROTECTION/FACE PROTECTION.
RESPONSE:
IF ON SKIN: WASH WITH PLENTY OF SOAP AND WATER.
IF INHALED:
REMOVE VICTIM TO FRESH AIR AND KEEP AT REST IN A POSITION COMFORTABLE FOR
BREATHING.
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES, IF
PRESENT AND EASY TO DO.
CONTINUE RINSING.
IMMEDIATELY CALL A POISON CENTER/DOCTOR/....
CALL A POISON CENTER OR DOCTOR/PHYSICIAN IF YOU FEEL UNWELL.
SPECIFIC TREATMENT (SEE ... ON THIS LABEL).
IF SKIN IRRITATION OCCURS: GET MEDICAL ADVICE/ATTENTION.
TAKE OFF CONTAMINATED CLOTHING AND WASH BEFORE REUSE.
STORAGE:
STORE IN A WELL-VENTILATED PLACE. KEEP CONTAINER TIGHTLY CLOSED.
STORE LOCKED UP.
PROTECT FROM SUNLIGHT. STORE IN A WELL-VENTILATED PLACE.
PROTECT FROM SUNLIGHT. DO NO EXPOSE TO TEMPERATURES EXCEEDING
50 DEG. C / 122 DEG. F.
DISPOSAL:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH LOCAL/REGIONAL/NATIONAL/
INTERNATIONAL REGULATION FOR HAZARDOUS WASTES.
| 3. COMPOSITION/INFORMATION ON INGREDIENTS | |
COMPONENT CAS # PERCENT
PETROLEUM DISTILLATES 8052-41-3 60 - 80
DIMETHYL CARBINOL 67-63-0 1 - 20
AMINOMODIFIED POLYDIMETHYLSILOXANE #80100382-5013P 1 - 20
BUTYL HYDRIDE 106-97-8 30 - 40
DIMETHYL METHANE 74-98-6 1 - 20
HMIS(R*) III* HAZARDOUS WARNINGS:
HEALTH 1
FLAMMABILITY 3
PHYSICAL 0
PERSONAL PROTECTIVE EQUIPMENT SEE SECTION 8
* SEE WWW.PAINT.ORG/HMIS OR CALL THE NPCA AT 1 (202) 462-6272 FOR MORE
INFORMATION ON THIS CURRENT RATING SYSTEM.
| 4. FIRST AID MEASURES | |
EYES:
IMMEDIATELY FLUSH EYES GENTLY WITH PLENTY OF WATER FOR AT LEAST 15 MINUTES
WHILE HOLDING EYELIDS APART. IF SYMPTOMS PERSIST OR THERE IS VISUAL
DIFFICULTY, SEEK MEDICAL ATTENTION.
SKIN CONTACT:
IN CASE OF CONTACT, IMMEDIATELY WASH CONTAMINATED AREA WITH PLENTY OF WATER
FOR AT LEAST 15 MINUTES. SEEK MEDICAL ATTENTION IF SYMPTOMS PERSIST. SEEK
MEDICAL ATTENTION IF SYMPTOMS PERSIST. WASH CLOTHING BEFORE REUSE.
INGESTION:
DO NOT INDUCE VOMITING. ASPIRATION INTO THE LUNGS CAN CAUSE SERIOUS DAMAGE.
CONTACT A PHYSICIAN, MEDICAL FACILITY, OR POISON CONTROL CENTER
IMMEDIATELY. IF VOMITING OCCURS SPONTANEOUSLY, KEEP HEAD BELOW HIPS TO
PREVENT ASPIRATION OF LIQUID INTO LUNGS.
INHALATION:
REMOVE TO FRESH AIR. IF NOT BREATHING, GIVE ARTIFICIAL RESPIRATION. IF
BREATHING IS DIFFICULT, GIVE OXYGEN. SEEK IMMEDIATE MEDICAL ATTENTION.
KEEP THE VICTIM WARM AND QUIET.
NOTES TO PHYSICIAN:
THIS MATERIAL IS AN ASPIRATION HAZARD. THIS MATERIAL IS AN ASPIRATION
HAZARD. POTENTIAL DANGER FROM ASPIRATION MUST BE WEIGHED AGAINST POSSIBLE
ORAL TOXICITY WHEN DECIDING WHETHER TO INDUCE VOMITING.
PREEXISTING DISORDERS OF THE FOLLOWING ORGANS (OR ORGAN SYSTEMS) MAY BE
AGGRAVATED BY EXPOSURE TO THIS MATERIAL:
SKIN; LUNG (FOR EXAMPLE, ASTHMA-LIKE CONDITIONS); KIDNEY; LIVER
| 5. FIRE FIGHTING MEASURES | |
FIRE AND/OR EXPLOSION HAZARDS:
THIS PRODUCT CONTAINS A COMPONENT(S) THAT IS CONSIDERED AN EXTREMELY
FLAMMABLE GAS(ES), WHICH HAS VAPORS THAT ARE HEAVIER THAN AIR AND MAY
TRAVEL ALONG THE GROUND OR BE MOVED BY VENTILATION AND IGNITED BY HEAT,
PILOT LIGHTS, OR OTHER FLAMES AND IGNITION SOURCES AT LOCATIONS DISTANT
FROM THE MATERIAL'S HANDLING POINT. THIS PRODUCT CONTAINS A COMPONENT(S)
THAT IS CONSIDERED A FLAMMABLE LIQUID, WHICH HAS VAPORS THAT ARE HEAVIER
THAN AIR AND MAY TRAVEL ALONG THE GROUND OR BE MOVED BY VENTILATION AND
IGNITED BY HEAT, PILOT LIGHTS, OR OTHER FLAMES AND IGNITION SOURCES AT
LOCATIONS DISTANT FROM THE MATERIAL'S HANDLING POINT.
FIRE FIGHTING INSTRUCTIONS:
USE CO2, FOAM OR DRY CHEMICAL. WATER IS GENERALLY NOT EFFECTIVE AND MAY
SPREAD FIRE; HOWEVER, WATER SPRAY MAY BE USED FROM A SAFE DISTANCE TO COOL
CLOSED CONTAINERS AND PROTECT SURROUNDING AREA.
| 6. ACCIDENTAL RELEASE MEASURES | |
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED:
VENTILATE CONTAMINATED AREA. REMOVE ALL SOURCES OF IGNITION. WEAR
APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT (PPE). STOP OR REDUCE DISCHARGE
IF IT CAN BE DONE SAFELY. AVOID RUN-OFF INTO STORM SEWERS AND DITCHES WHICH
MAY LEAD TO NATURAL WATERWAYS. IF RUNOFF OCCURS, NOTIFY AUTHORITIES AS
REQUIRED. CLEAN UP WITH ABSORBENT MATERIAL. PLACE ABSORBENT MATERIALS INTO
CONTAINER AND CLOSE IT TIGHTLY. DISPOSE OF CONTAINER PROPERLY.
| 7. HANDLING AND STORAGE | |
HANDLING:
DO NOT USE NEAR IGNITION SOURCES. AVOID PROLONGED OR REPEATED CONTACT WITH
SKIN. THIS MATERIAL CAN BE HARMFUL OR IRRITATING. USE WITH ADEQUATE
VENTILATION. NORMAL PRECAUTIONS COMMON TO SAFE MANUFACTURING PRACTICE
SHOULD BE FOLLOWED IN HANDLING AND STORAGE. AVOID PROLONGED OR REPEATED
BREATHING OF VAPOR. DO NOT USE NEAR IGNITION SOURCES. IF VENTILATION IS NOT
SUFFICIENT, WEAR PROPER RESPIRATORY EQUIPMENT. DO NOT STORE CONTAINERS IN
EXCESSIVE HEAT OR DIRECT SUNLIGHT. PROTECT CONTAINER AGAINST PHYSICAL
DAMAGE.
STORAGE:
STORE IN A COOL, DRY, WELL VENTILATED AREA AWAY FROM ALL SOURCES OF
IGNITION. EMPTY CONTAINER MAY CONTAIN RESIDUES WHICH ARE HAZARDOUS. DO NOT
STORE AT TEMPERATURES ABOVE 120 DEGREES F. STORE AWAY FROM INCOMPATIBLE
MATERIALS SUCH AS MATERIALS THAT SUPPORT COMBUSTION (OXIDIZING MATERIALS)
AND CORROSIVE MATERIALS (STRONG ACIDS OR BASES).
| 8. EXPOSURE CONTROLS / PERSONAL PROTECTION | |
ENGINEERING CONTROLS:
VENTILATION SHOULD BE ADEQUATE TO PREVENT EXPOSURES ABOVE THE LIMITS
INDICATED IN "SECTION 2" OF THIS MSDS (FROM KNOWN, SUSPECTED OR APPARENT
ADVERSE EFFECTS). VENTILATION IS REQUIRED TO MAINTAIN OPERATOR EXPOSURE
BELOW PUBLISHED EXPOSURE LIMITS. LOCAL EXHAUST SHOULD BE USED IN AREAS
WHERE EXPOSURE LIMITS MAY BE EXCEEDED.
EYE PROTECTION:
WEAR CHEMICALLY RESISTANT SAFETY GLASSES WITH SIDE SHIELDS WHEN HANDLING
THIS PRODUCT. WEAR ADDITIONAL EYE PROTECTION SUCH AS CHEMICAL SPLASH
GOGGLES AND/OR FACE SHIELD WHEN THE POSSIBILITY EXISTS FOR EYE CONTACT
WITH SPLASHING OR SPRAYING LIQUID OR AIRBORNE MATERIAL. DO NOT WEAR
CONTACT LENSES. HAVE AN EYE WASH STATION AVAILABLE.
SKIN PROTECTION:
THE USE OF CHEMICALLY RESISTANT GLOVES IS RECOMMENDED IF THERE IS ANY
POSSIBILITY OF PROLONGED OR REPEATED LIQUID CONTACT WITH SKIN.
RESPIRATORY PROTECTION:
USE NIOSH APPROVED RESPIRATOR WHERE THERE IS LIKELIHOOD OF INHALATION OF
THE PRODUCT MIST, SPRAY OR AEROSOL. A SUPPLIED AIR RESPIRATOR SHOULD BE
USED IF VENTILATION IS NOT SUFFICIENT TO MAINTAIN EXPOSURE LIMITS.
COMPONENT CAS # ACGIH TLV OSHA PEL OTHER
PETROLEUM DISTILLATES 8052-41-3 100 PPM TWA 500 PPM NOT
ESTABLISHED
DIMETHYL CARBINOL 67-63-0 200 PPM NOT 200 PPM 8 HR
ESTABLISHED TWA
AMINOMODIFIED #80100382- NOT NOT NOT
POLYDIMETHYLSILOXANE 5013P ESTABLISHED ESTABLISHED ESTABLISHED
BUTYL HYDRIDE 106-97-8 NOT NOT NOT
ESTABLISHED ESTABLISHED ESTABLISHED
DIMETHYL METHANE 74-98-6 NOT NOT NOT
ESTABLISHED ESTABLISHED ESTABLISHED
| 9. PHYSICAL AND CHEMICAL PROPERTIES | |
PHYSICAL STATE: AEROSOL CAN
LOWER FLAMMABILITY LIMIT (%): NOT APPLICABLE
UPPER FLAMMABILITY LIMIT (%): NOT APPLICABLE
APPEARANCE: CLEAR COLORLESS
ODOR: LIGHT HYDROCARBON
VAPOR PRESSURE (PSIG @ 70 DEG. F): 46.0
ODOR THRESHOLD: MILD
VAPOR DENSITY [AIR = 1]: 4.58
PH: NOT APPLICABLE
RELATIVE DENSITY (H2O=1): 0.71
MELTING/FREEZING POINT (DEG. F): NO DATA AVAILABLE
SOLUBILITY IN WATER: NEGLIGIBLE; 0-1%
BOILING POINT (DEG. F): NO DATA AVAILABLE
PARTIAL COEFFICIENT N-OCTANOL/WATER: NO DATA AVAILABLE
FLASH POINT (DEG. F PMCC): NOT APPLICABLE
AUTOIGNITION TEMPERATURE (DEG. F): NOT APPLICABLE
EVAPORATION RATE: 0.5-2 (N-BUTYL ACETATE = 1)
DECOMPOSITION TEMPERATURE (DEG. F): NO DATA AVAILABLE
FLAMMABILITY (SOLID, GAS): NO DATA AVAILABLE
VISCOSITY, DYNAMIC (CST): NO DATA AVAILABLE
PERCENT VOCS (%): 60 - 80
| 10. STABILITY AND REACTION | |
CHEMICAL STABILITY: STABLE.
CONDITIONS TO AVOID:
AVOID CONTACT WITH:
STRONG OXIDIZING AGENTS. IGNITION SOURCES SUCH AS OPEN FLAMES, SPARKS,
STATIC DISCHARGES OR GLOWING METAL SURFACES. ACETALDEHYDE. ACIDS. CHLORINE.
ETHYLENE OXIDE. ISOCYANATES.
DECOMPOSITION PRODUCTS:
BURNING CAN PRODUCE THE FOLLOWING COMBUSTION PRODUCTS:
CARBON DIOXIDE AND CARBON MONOXIDE. VARIOUS HYDROCARBONS.
| 11. TOXICOLOGICAL INFORMATION | |
REPRODUCTIVE & DEVELOPMENTAL TOXICITY: NO DATA AVAILABLE.
IARC CARCINOGEN DESIGNATION:
IARC 3: CLASSIFICATION NOT POSSIBLE FROM CURRENT DATA.
INGREDIENT CAS # TOXICOLOGICAL DATA
PETROLEUM DISTILLATES 8052-41-3 DERMAL LD50 RABBIT: >3 G/KG
ORAL LD50 RAT: >5 G/KG
DIMETHYL CARBINOL 67-63-0 DERMAL LD50 RABBIT: 12870 MG/KG
ORAL LD50 RABBIT: 5030 MG/KG
INHALATION LC50 (8H) RAT: 51 MG/L
| 12. ECOLOGICAL INFORMATION | |
ECOLOGICAL TOXICITY: NO DATA AVAILABLE
MOBILITY:
NO DATA AVAILABLE THIS MATERIAL (OR ONE OF ITS COMPONENTS), DISSOLVES IN
WATER. IF IT ENTERS THE SOIL, IT WILL BE HIGHLY MOBILE AND MAY CONTAMINATE
GROUND WATER.
INGREDIENT CAS # TOXICOLOGICAL DATA
NO DATA AVAILABLE
| 13. DISPOSAL CONSIDERATIONS | |
DISPOSAL: DISPOSE ACCORDING TO FEDERAL, STATE AND LOCAL REGULATIONS.
| 14. TRANSPORTATION INFORMATION | |
AGENCY UN NUMBER PROPER SHIPPING NAME HAZARD CLASS PACKING GROUP
DOT UN1950 AEROSOLS, FLAMMABLE+ 2.1 NOT APPLICABLE
IATA UN1950 AEROSOLS, FLAMMABLE+ 2.1 NOT APPLICABLE
IMDG UN1950 AEROSOLS, FLAMMABLE+ 2.1 NOT APPLICABLE
+ "LIMITED QUANTITIES" MAY BE APPLICABLE FOR THIS TRANSPORTATION MODE.
| 15. REGULATORY INFORMATION | |
WARNING:
THIS PRODUCT CONTAINS THE FOLLOWING CHEMICALS THAT ARE SUBJECT TO REPORTING
REQUIREMENTS FOR THE FOLLOWING REGULATORY BODIES LISTED BELOW:
COMPONENT CAS # % BY WEIGHT REGULATORY BODY
NO COMPONENTS LISTED IN THIS SECTION. SARA SECTION 313
WARNING:
THIS PRODUCT MAY CONTAIN CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO
CAUSE CANCER. SEE LIST BELOW.
NO COMPONENTS LISTED IN THIS SECTION. PROP65 CANCER
WARNING:
THIS PRODUCT MAY CONTAIN CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO
CAUSE BIRTH DEFECTS. SEE LIST BELOW.
NO COMPONENTS LISTED IN THIS SECTION. PROP65 BIRTH DEFECTS
ALL COMPONENTS OF THIS PRODUCT ARE LISTED ON THE TSCA INVENTORY.
| 16. OTHER INFORMATION | |
OTHER INFORMATION: MSDS PREPARED BY L. DEAN SWARTZ, MSDS COORDINATOR
VERSION DATE: 04/02/15
THIS INFORMATION CONTAINED IN THIS MSDS IS BELIEVED TO BE ACCURATE AS
OF THE VERSION DATE, BUT IS NOT WARRANTED TO BE. SINCE THE USE OF THIS
INFORMATION AND THE CONDITIONS OF USE OF THIS PRODUCT ARE NOT WITHIN
THE CONTROL OF STONER INC, IT IS THE USER'S OBLIGATION TO DETERMINE THE
CONDITIONS OF SAFE USE.