| Common Name: | ABRASIVE PRODUCTS, 775L STIKIT, HOOKIT |
| Manufacturer: | 3M |
| SDS Revision Date: | 5/12/2017 |
| SDS Format: | GHS-US |
| Item Number(s): | 38XK23 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M(TM) ABRASIVE PRODUCTS, 775L STIKIT(TM), HOOKIT(TM)
05/12/17
3M
SAFETY DATA SHEET
COPYRIGHT, 2017, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR THE
PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 33-3276-4
VERSION NUMBER: 1.08
ISSUE DATE: 05/12/17
SUPERCEDES DATE: 04/12/17
| SECTION 1: IDENTIFICATION |  |
1.1. PRODUCT IDENTIFIER:
3M(TM) ABRASIVE PRODUCTS, 775L STIKIT(TM), HOOKIT(TM)
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE: ABRASIVE PRODUCT
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: ABRASIVE SYSTEMS DIVISION
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
NOT CLASSIFIED AS HAZARDOUS ACCORDING TO OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
2.2. LABEL ELEMENTS:
SIGNAL WORD: NOT APPLICABLE.
SYMBOLS: NOT APPLICABLE.
PICTOGRAMS: NOT APPLICABLE.
2.3. HAZARDS NOT OTHERWISE CLASSIFIED:
11% OF THE MIXTURE CONSISTS OF INGREDIENTS OF UNKNOWN ACUTE ORAL TOXICITY.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
CERAMIC ALUMINUM OXIDE / ALUMINUM 1344-28-1 15 - 40
OXIDE MINERAL BLEND (NON-FIBROUS)
FILLER 37244-96-5 5 - 15
FILLER 1332-58-7 0 - 5
LUBRICANT 68424-16-8 0.5 - 1.5
SYNTHETIC AMORPHOUS SILICA, FUMED, 112945-52-5 0 - 1.5
CRYSTALLINE FREE
TITANIUM DIOXIDE 13463-67-7 0.2 - 1.5
CURED RESIN MIXTURE 15 - 40
FILM BACKING MIXTURE 10 - 30
HOOKIT BACKING MIXTURE 0 - 25
STIKIT BACKING MIXTURE 0 - 15
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
WASH WITH SOAP AND WATER. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL ATTENTION.
EYE CONTACT:
FLUSH WITH LARGE AMOUNTS OF WATER. REMOVE CONTACT LENSES IF EASY TO DO.
CONTINUE RINSING. IF SIGNS/SYMPTOMS PERSIST, GET MEDICAL ATTENTION.
IF SWALLOWED: NO NEED FOR FIRST AID IS ANTICIPATED.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED: NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
IN CASE OF FIRE:
USE A FIRE FIGHTING AGENT SUITABLE FOR ORDINARY COMBUSTIBLE MATERIAL SUCH
AS WATER OR FOAM TO EXTINGUISH.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
NONE INHERENT IN THIS PRODUCT.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
NO SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS ARE ANTICIPATED.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
OBSERVE PRECAUTIONS FROM OTHER SECTIONS.
6.2. ENVIRONMENTAL PRECAUTIONS: AVOID RELEASE TO THE ENVIRONMENT.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP: NOT APPLICABLE.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
FOR INDUSTRIAL OR PROFESSIONAL USE ONLY. DO NOT USE IN A CONFINED AREA WITH
MINIMAL AIR EXCHANGE. AVOID BREATHING OF DUST CREATED BY SANDING, GRINDING
OR MACHINING. DAMAGED PRODUCT CAN BREAK APART DURING USE AND CAUSE SERIOUS
INJURY TO FACE OR EYES. CHECK PRODUCT FOR DAMAGE SUCH AS CRACKS OR NICKS
PRIOR TO USE. REPLACE IF DAMAGED. ALWAYS WEAR EYE AND FACE PROTECTION WHEN
WORKING AT SANDING OR GRINDING OPERATIONS OR WHEN NEAR SUCH OPERATIONS.
COMBUSTIBLE DUST MAY FORM BY ACTION OF THIS PRODUCT ON ANOTHER MATERIAL
(SUBSTRATE). DUST GENERATED FROM THE SUBSTRATE DURING USE OF THIS PRODUCT
MAY BE EXPLOSIVE IF IN SUFFICIENT CONCENTRATION WITH AN IGNITION SOURCE.
DUST DEPOSITS SHOULD NOT BE ALLOWED TO ACCUMULATE ON SURFACES BECAUSE OF
THE POTENTIAL FOR SECONDARY EXPLOSIONS.
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
NO SPECIAL STORAGE REQUIREMENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN THE TABLE
BELOW, AN OCCUPATIONAL EXPOSURE LIMIT IS NOT AVAILABLE FOR THE COMPONENT.
INGREDIENT C.A.S. NO. AGENCY LIMIT TYPE ADDITIONAL
COMMENTS
SILICA, AMORPHOUS 112945-52-5 OSHA TWA CONCENTRATION:
0.8 MG/M3
TWA:
20 MILLIONS OF
PARTICLES/CU. FT.
FILLER 1332-58-7 ACGIH TWA (RESPIRABLE A4:
FRACTION): 2 MG/M3 NOT CLASS.
AS HUMAN
CARCIN
KAOLIN, TOTAL DUST 1332-58-7 OSHA TWA (AS TOTAL
DUST): 15 MG/M3
TWA (RESPIRABLE
FRACTION): 5 MG/M3
ALUMINUM, INSOLUBLE 1344-28-1 ACGIH TWA (RESPIRABLE A4:
COMPOUNDS FRACTION): 1 MG/M3 NOT CLASS.
AS HUMAN
CARCIN
CERAMIC ALUMINUM 1344-28-1 OSHA TWA (AS TOTAL
OXIDE / ALUMINUM OXIDE DUST): 15 MG/M3
MINERAL BLEND
(NON-FIBROUS) TWA (RESPIRABLE
FRACTION): 5 MG/M3
TITANIUM DIOXIDE 13463-67-7 ACGIH TWA: 10 MG/M3 A4:
NOT CLASS.
AS HUMAN
CARCIN
TITANIUM DIOXIDE 13463-67-7 OSHA TWA (AS TOTAL
DUST): 15 MG/M3
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
AIHA: AMERICAN INDUSTRIAL HYGIENE ASSOCIATION
CMRG: CHEMICAL MANUFACTURER'S RECOMMENDED GUIDELINES
OSHA:
UNITED STATES DEPARTMENT OF LABOR - OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION
TWA: TIME-WEIGHTED-AVERAGE
STEL: SHORT TERM EXPOSURE LIMIT
CEIL: CEILING
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
PROVIDE APPROPRIATE LOCAL EXHAUST VENTILATION FOR SANDING, GRINDING OR
MACHINING. USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST
VENTILATION TO CONTROL AIRBORNE EXPOSURES TO BELOW RELEVANT EXPOSURE LIMITS
AND/OR CONTROL DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS NOT
ADEQUATE, USE RESPIRATORY PROTECTION EQUIPMENT. PROVIDE LOCAL EXHAUST AT
PROCESS EMISSION SOURCES TO CONTROL EXPOSURE NEAR THE SOURCE AND TO PREVENT
THE ESCAPE OF DUST INTO THE WORK AREA. ENSURE THAT DUST-HANDLING SYSTEMS
(SUCH AS EXHAUST DUCTS, DUST COLLECTORS, VESSELS, AND PROCESSING EQUIPMENT)
ARE DESIGNED IN A MANNER TO PREVENT THE ESCAPE OF DUST INTO THE WORK AREA
(I.E., THERE IS NO LEAKAGE FROM THE EQUIPMENT).
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
TO MINIMIZE THE RISK OF INJURY TO FACE AND EYES, ALWAYS WEAR EYE AND FACE
PROTECTION WHEN WORKING AT SANDING OR GRINDING OPERATIONS OR WHEN NEAR SUCH
OPERATIONS. SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON
THE RESULTS OF AN EXPOSURE ASSESSMENT. THE FOLLOWING EYE/FACE PROTECTION(S)
ARE RECOMMENDED: SAFETY GLASSES WITH SIDE SHIELDS
SKIN/HAND PROTECTION:
WEAR APPROPRIATE GLOVES TO MINIMIZE RISK OF INJURY TO SKIN FROM CONTACT
WITH DUST OR PHYSICAL ABRASION FROM GRINDING OR SANDING.
RESPIRATORY PROTECTION:
ASSESS EXPOSURE CONCENTRATIONS OF ALL MATERIALS INVOLVED IN THE WORK
PROCESS. CONSIDER MATERIAL BEING ABRADED WHEN DETERMINING THE APPROPRIATE
RESPIRATORY PROTECTION. SELECT AND USE APPROPRIATE RESPIRATORS TO PREVENT
INHALATION OVEREXPOSURE. AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF
A RESPIRATOR IS REQUIRED. IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS
PART OF A FULL RESPIRATORY PROTECTION PROGRAM. BASED ON THE RESULTS OF THE
EXPOSURE ASSESSMENT, SELECT FROM THE FOLLOWING RESPIRATOR TYPE(S) TO REDUCE
INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
PARTICULATES
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: SOLID
ODOR, COLOR, GRADE: SOLID ABRASIVE PRODUCT
ODOR THRESHOLD: NOT APPLICABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: NOT APPLICABLE
FLASH POINT: NOT APPLICABLE
EVAPORATION RATE: NOT APPLICABLE
FLAMMABILITY (SOLID, GAS): NOT CLASSIFIED
FLAMMABLE LIMITS (LEL): NOT APPLICABLE
FLAMMABLE LIMITS (UEL): NOT APPLICABLE
VAPOR PRESSURE: NOT APPLICABLE
VAPOR DENSITY: NOT APPLICABLE
SPECIFIC GRAVITY: NOT APPLICABLE
SOLUBILITY IN WATER: NOT APPLICABLE
SOLUBILITY- NON-WATER: NOT APPLICABLE
AUTOIGNITION TEMPERATURE: NOT APPLICABLE
DECOMPOSITION TEMPERATURE: NOT APPLICABLE
VISCOSITY: NOT APPLICABLE
VOLATILE ORGANIC COMPOUNDS: NOT APPLICABLE
PERCENT VOLATILE: NOT APPLICABLE
VOC LESS H2O & EXEMPT SOLVENTS: NOT APPLICABLE
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL IS CONSIDERED TO BE NON REACTIVE UNDER NORMAL USE CONDITIONS.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID: NONE KNOWN.
10.5. INCOMPATIBLE MATERIALS: NONE KNOWN.
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR THE
SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT BELOW
THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
DUST FROM GRINDING, SANDING OR MACHINING MAY CAUSE IRRITATION OF THE
RESPIRATORY SYSTEM. SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL
DISCHARGE, HEADACHE, HOARSENESS, AND NOSE AND THROAT PAIN.
SKIN CONTACT:
MECHANICAL SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABRASION, REDNESS, PAIN, AND ITCHING.
ALLERGIC SKIN REACTION (NON-PHOTO INDUCED) IN SENSITIVE PEOPLE:
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, BLISTERING, AND ITCHING.
EYE CONTACT:
MECHANICAL EYE IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE PAIN, REDNESS, TEARING AND CORNEAL ABRASION.
DUST CREATED BY GRINDING, SANDING, OR MACHINING MAY CAUSE EYE IRRITATION.
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND BLURRED OR
HAZY VISION.
INGESTION: NO HEALTH EFFECTS ARE EXPECTED.
CARCINOGENICITY:
INGREDIENT CAS NO. CLASS DESCRIPTION REGULATION
TITANIUM DIOXIDE 13463-67-7 GRP. 2B: INTERNATIONAL AGENCY
POSSIBLE HUMAN CARC. FOR RESEARCH ON CANCER
ADDITIONAL INFORMATION:
THIS DOCUMENT COVERS ONLY THE 3M PRODUCT. FOR COMPLETE ASSESSMENT, WHEN
DETERMINING THE DEGREE OF HAZARD, THE MATERIAL BEING ABRADED MUST ALSO BE
CONSIDERED.
THIS PRODUCT CONTAINS TITANIUM DIOXIDE. CANCER OF THE LUNGS HAS BEEN
OBSERVED IN RATS THAT INHALED HIGH LEVELS OF TITANIUM DIOXIDE. NO EXPOSURE
TO INHALED TITANIUM DIOXIDE IS EXPECTED DURING THE NORMAL HANDLING AND USE
OF THIS PRODUCT. TITANIUM DIOXIDE WAS NOT DETECTED WHEN AIR SAMPLING WAS
CONDUCTED DURING SIMULATED USE OF SIMILAR PRODUCTS CONTAINING TITANIUM
DIOXIDE. THEREFORE, THE HEALTH EFFECTS ASSOCIATED WITH TITANIUM DIOXIDE ARE
NOT EXPECTED DURING THE NORMAL USE OF THIS PRODUCT.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT INGESTION NO DATA AVAILABLE;
CALCULATED ATE:
>5,000 MG/KG
CERAMIC ALUMINUM OXIDE / DERMAL LD50:
ALUMINUM OXIDE MINERAL BLEND ESTIMATED TO BE
(NON-FIBROUS) >5,000 MG/KG
CERAMIC ALUMINUM OXIDE / INHALATION- RAT LC50: >2.3 MG/L
ALUMINUM OXIDE MINERAL BLEND DUST/MIST
(NON-FIBROUS) (4 HOURS)
CERAMIC ALUMINUM OXIDE / INGESTION RAT LD50: >5,000 MG/KG
ALUMINUM OXIDE MINERAL BLEND
(NON-FIBROUS)
FILLER DERMAL LD50:
ESTIMATED TO BE
>5,000 MG/KG
FILLER INGESTION LD50:
ESTIMATED TO BE
2,000 - 5,000 MG/KG
FILLER DERMAL LD50:
ESTIMATED TO BE
>5,000 MG/KG
FILLER INGESTION HUMAN LD50: >15,000 MG/KG
SYNTHETIC AMORPHOUS SILICA, DERMAL RABBIT LD50: >5,000 MG/KG
FUMED, CRYSTALLINE FREE
SYNTHETIC AMORPHOUS SILICA, INHALATION- RAT LC50: >0.691 MG/L
FUMED, CRYSTALLINE FREE DUST/MIST
(4 HOURS)
SYNTHETIC AMORPHOUS SILICA, INGESTION RAT LD50: >5,110 MG/KG
FUMED, CRYSTALLINE FREE
TITANIUM DIOXIDE DERMAL RABBIT LD50: >10,000 MG/KG
TITANIUM DIOXIDE INHALATION- RAT LC50: >6.82 MG/L
DUST/MIST
(4 HOURS)
TITANIUM DIOXIDE INGESTION RAT LD50: >10,000 MG/KG
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
CERAMIC ALUMINUM OXIDE / RABBIT NO SIGNIFICANT IRRITATION
ALUMINUM OXIDE MINERAL BLEND
(NON-FIBROUS)
FILLER PROFESSIONAL NO SIGNIFICANT IRRITATION
JUDGEMENT
FILLER PROFESSIONAL NO SIGNIFICANT IRRITATION
JUDGEMENT
SYNTHETIC AMORPHOUS SILICA, RABBIT NO SIGNIFICANT IRRITATION
FUMED, CRYSTALLINE FREE
TITANIUM DIOXIDE RABBIT NO SIGNIFICANT IRRITATION
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
CERAMIC ALUMINUM OXIDE / RABBIT NO SIGNIFICANT IRRITATION
ALUMINUM OXIDE MINERAL BLEND
(NON-FIBROUS)
FILLER PROFESSIONAL MILD IRRITANT
JUDGEMENT
FILLER PROFESSIONAL NO SIGNIFICANT IRRITATION
JUDGEMENT
SYNTHETIC AMORPHOUS SILICA, RABBIT NO SIGNIFICANT IRRITATION
FUMED, CRYSTALLINE FREE
TITANIUM DIOXIDE RABBIT NO SIGNIFICANT IRRITATION
SKIN SENSITIZATION:
NAME SPECIES VALUE
SYNTHETIC AMORPHOUS SILICA, HUMAN NOT CLASSIFIED
FUMED, CRYSTALLINE FREE AND
ANIMAL
TITANIUM DIOXIDE HUMAN NOT CLASSIFIED
AND
ANIMAL
RESPIRATORY SENSITIZATION:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
CERAMIC ALUMINUM OXIDE / IN VITRO NOT MUTAGENIC
ALUMINUM OXIDE MINERAL BLEND
(NON-FIBROUS)
SYNTHETIC AMORPHOUS SILICA, IN VITRO NOT MUTAGENIC
FUMED, CRYSTALLINE FREE
TITANIUM DIOXIDE IN VITRO NOT MUTAGENIC
TITANIUM DIOXIDE IN VIVO NOT MUTAGENIC
CARCINOGENICITY:
NAME ROUTE SPECIES VALUE
CERAMIC ALUMINUM OXIDE / INHALATION RAT NOT CARCINOGENIC
ALUMINUM OXIDE MINERAL
BLEND (NON-FIBROUS)
FILLER INHALATION MULTIPLE NOT CARCINOGENIC
ANIMAL
SPECIES
SYNTHETIC AMORPHOUS NOT MOUSE SOME POSITIVE DATA
SILICA, FUMED, SPECIFIED EXIST, BUT THE DATA
CRYSTALLINE FREE ARE NOT SUFFICIENT
FOR CLASSIFICATION
TITANIUM DIOXIDE INGESTION MULTIPLE NOT CARCINOGENIC
ANIMAL
SPECIES
TITANIUM DIOXIDE INHALATION RAT CARCINOGENIC
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
NAME ROUTE VALUE
SYNTHETIC AMORPHOUS SILICA, INGESTION NOT CLASSIFIED FOR FEMALE
FUMED, CRYSTALLINE FREE REPRODUCTION
SYNTHETIC AMORPHOUS SILICA, INGESTION NOT CLASSIFIED FOR MALE
FUMED, CRYSTALLINE FREE REPRODUCTION
SYNTHETIC AMORPHOUS SILICA, INGESTION NOT CLASSIFIED FOR DEVELOPMENT
FUMED, CRYSTALLINE FREE
NAME SPECIES TEST RESULT EXPOSURE DURATION
SYNTHETIC AMORPHOUS RAT NOAEL: 509 MG/KG/DAY 1 GENERATION
SILICA, FUMED,
CRYSTALLINE FREE
SYNTHETIC AMORPHOUS RAT NOAEL: 497 MG/KG/DAY 1 GENERATION
SILICA, FUMED,
CRYSTALLINE FREE
SYNTHETIC AMORPHOUS RAT NOAEL: 1,350 MG/KG/DAY DURING
SILICA, FUMED, ORGANOGENESIS
CRYSTALLINE FREE
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
CERAMIC ALUMINUM INHALATION PNEUMOCONIOSIS SOME POSITIVE DATA
OXIDE / ALUMINUM EXIST, BUT THE DATA
OXIDE MINERAL BLEND ARE NOT SUFFICIENT
(NON-FIBROUS) FOR CLASSIFICATION
CERAMIC ALUMINUM INHALATION PULMONARY FIBROSIS NOT CLASSIFIED
OXIDE / ALUMINUM
OXIDE MINERAL BLEND
(NON-FIBROUS)
FILLER INHALATION PNEUMOCONIOSIS CAUSES DAMAGE TO
ORGANS THROUGH
PROLONGED OR
REPEATED EXPOSURE
FILLER INHALATION PULMONARY FIBROSIS NOT CLASSIFIED
SYNTHETIC AMORPHOUS INHALATION RESPIRATORY SYSTEM NOT CLASSIFIED
SILICA, FUMED, SILICOSIS
CRYSTALLINE FREE
TITANIUM DIOXIDE INHALATION RESPIRATORY SYSTEM SOME POSITIVE DATA
EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
TITANIUM DIOXIDE INHALATION PULMONARY FIBROSIS NOT CLASSIFIED
NAME SPECIES TEST RESULT EXPOSURE DURATION
CERAMIC ALUMINUM HUMAN NOAEL: NOT AVAILABLE OCCUPATIONAL
OXIDE / ALUMINUM EXPOSURE
OXIDE MINERAL
BLEND (NON-
FIBROUS)
CERAMIC ALUMINUM HUMAN NOAEL: NOT AVAILABLE OCCUPATIONAL
OXIDE / ALUMINUM EXPOSURE
OXIDE MINERAL
BLEND (NON-
FIBROUS)
FILLER HUMAN NOAEL: NA OCCUPATIONAL
EXPOSURE
FILLER RAT NOAEL: NOT AVAILABLE
SYNTHETIC HUMAN NOAEL: NOT AVAILABLE OCCUPATIONAL
AMORPHOUS EXPOSURE
SILICA, FUMED,
CRYSTALLINE
FREE
TITANIUM DIOXIDE RAT LOAEL: 0.01 MG/L 2 YEARS
TITANIUM DIOXIDE HUMAN NOAEL: NOT AVAILABLE OCCUPATIONAL
EXPOSURE
ASPIRATION HAZARD:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/ CONTAINER IN ACCORDANCE WITH THE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
PRIOR TO DISPOSAL, CONSULT ALL APPLICABLE AUTHORITIES AND REGULATIONS TO
INSURE PROPER CLASSIFICATION. THE SUBSTRATE THAT WAS ABRADED MUST BE
CONSIDERED AS A FACTOR IN THE DISPOSAL METHOD FOR THIS PRODUCT. DISPOSE OF
WASTE PRODUCT IN A PERMITTED INDUSTRIAL WASTE FACILITY. AS A DISPOSAL
ALTERNATIVE, INCINERATE IN A PERMITTED WASTE INCINERATION FACILITY. IF NO
OTHER DISPOSAL OPTIONS ARE AVAILABLE, WASTE PRODUCT MAY BE PLACED IN A
LANDFILL PROPERLY DESIGNED FOR INDUSTRIAL WASTE.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
| SECTION 14: TRANSPORT INFORMATION | |
NOT REGULATED PER U.S. DOT, IATA OR IMO.
THESE TRANSPORTATION CLASSIFICATIONS ARE PROVIDED AS A CUSTOMER SERVICE. AS
THE SHIPPER YOU REMAIN RESPONSIBLE FOR COMPLYING WITH ALL APPLICABLE LAWS
AND REGULATIONS, INCLUDING PROPER TRANSPORTATION CLASSIFICATION AND
PACKAGING. 3M TRANSPORTATION CLASSIFICATIONS ARE BASED ON PRODUCT
FORMULATION, PACKAGING, 3M POLICIES AND 3M UNDERSTANDING OF APPLICABLE
CURRENT REGULATIONS. 3M DOES NOT GUARANTEE THE ACCURACY OF THIS
CLASSIFICATION INFORMATION. THIS INFORMATION APPLIES ONLY TO TRANSPORTATION
CLASSIFICATION AND NOT THE PACKAGING, LABELING, OR MARKING REQUIREMENTS.
THE ORIGINAL 3M PACKAGE IS CERTIFIED FOR U.S. GROUND SHIPMENT ONLY. IF YOU
ARE SHIPPING BY AIR OR OCEAN, THE PACKAGE MAY NOT MEET APPLICABLE
REGULATORY REQUIREMENTS.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
311/312 HAZARD CATEGORIES:
FIRE HAZARD: NO
PRESSURE HAZARD: NO
REACTIVITY HAZARD: NO
IMMEDIATE HAZARD: NO
DELAYED HAZARD: NO
EPCRA 311/312 HAZARD CLASSIFICATIONS (EFFECTIVE JANUARY 1, 2018):
PHYSICAL HAZARDS: NOT APPLICABLE
HEALTH HAZARDS: NOT APPLICABLE
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
15.3. CHEMICAL INVENTORIES:
THIS PRODUCT IS AN ARTICLE AS DEFINED BY TSCA REGULATIONS, AND IS EXEMPT
FROM TSCA INVENTORY LISTING REQUIREMENTS.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 0
FLAMMABILITY 1
INSTABILITY 0
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED FOR
USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO INCLUDE
THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT ARE KNOWN
TO BE GENERATED IN SIGNIFICANT QUANTITIES.
HMIS HAZARD CLASSIFICATION:
HEALTH 0
FLAMMABILITY 1
PHYSICAL HAZARD 0
PERSONAL PROTECTION X - SEE PPE SECTION.
HAZARDOUS MATERIAL IDENTIFICATION SYSTEM (HMIS(R*) IV) HAZARD RATINGS ARE
DESIGNED TO INFORM EMPLOYEES OF CHEMICAL HAZARDS IN THE WORKPLACE. THESE
RATINGS ARE BASED ON THE INHERENT PROPERTIES OF THE MATERIAL UNDER EXPECTED
CONDITIONS OF NORMAL USE AND ARE NOT INTENDED FOR USE IN EMERGENCY
SITUATIONS. HMIS(R*) IV RATINGS ARE TO BE USED WITH A FULLY IMPLEMENTED
HMIS(R*) IV PROGRAM. HMIS(R*) IS A REGISTERED MARK OF THE AMERICAN COATINGS
ASSOCIATION (ACA).
DOCUMENT GROUP: 33-3276-4
VERSION NUMBER: 1.08
ISSUE DATE: 05/12/17
SUPERCEDES DATE: 04/12/17
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED IN
ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM