| Common Name: | MODEL PC-3 |
| Manufacturer: | WORTHINGTON INDUSTRIES |
| SDS Revision Date: | 7/26/2016 |
| SDS Format: | GHS-CA |
| Item Number(s): | 3AC23 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
W
WORTHINGTON INDUSTRIES
SAFETY DATA SHEET
| 1. IDENTIFICATION |  |
PRODUCT IDENTIFIER: MODEL PC-3
OTHER MEANS OF IDENTIFICATION:
SDS NUMBER: WC046
RECOMMENDED USE: BRAZING ROD.
RECOMMENDED RESTRICTIONS: NONE KNOWN.
MANUFACTURER/IMPORTER/SUPPLIER/DISTRIBUTOR INFORMATION:
MANUFACTURER/SUPPLIER: WORTHINGTON INDUSTRIES INCORPORATED
ADDRESS:
200 OLD WILSON BRIDGE ROAD
COLUMBUS, OH 43085
UNITED STATES
EMAIL: CYLINDERS@WORTHINGTONINDUSTRIES.COM
TELEPHONE NUMBER: 866-928-2657
CHEMTREC - 24 HOURS:
WITHIN US AND CANADA: 800-424-9300
OUTSIDE US AND CANADA: +1 703-741-5970 (COLLECT CALLS ACCEPTED)
| 2. HAZARD(S) IDENTIFICATION | |
PHYSICAL HAZARDS: NOT CLASSIFIED.
HEALTH HAZARDS: NOT CLASSIFIED.
ENVIRONMENTAL HAZARDS: NOT CLASSIFIED.
LABEL ELEMENTS:
HAZARD SYMBOL: NONE.
SIGNAL WORD: NONE.
HAZARD STATEMENT:
VERY TOXIC TO AQUATIC LIFE. HARMFUL TO AQUATIC LIFE WITH LONG LASTING
EFFECTS.
PRECAUTIONARY STATEMENTS:
PREVENTION: OBSERVE GOOD INDUSTRIAL HYGIENE PRACTICES.
RESPONSE: WASH THOROUGHLY AFTER HANDLING.
STORAGE: STORE AWAY FROM INCOMPATIBLE MATERIALS.
DISPOSAL:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
OTHER HAZARDS: NONE KNOWN.
SUPPLEMENTAL INFORMATION: NONE.
| 3. COMPOSITION/INFORMATION ON INGREDIENTS | |
MIXTURES:
CHEMICAL NAME CAS NUMBER %
COPPER, ELEMENTAL 7440-50-8 80-95
SILVER, ELEMENTAL 7440-22-4 0-15
PHOSPHOROUS 7723-14-0 5-7.5
COMPOSITION COMMENTS:
ALL CONCENTRATIONS ARE IN PERCENT BY WEIGHT UNLESS INGREDIENT IS A GAS. GAS
CONCENTRATIONS ARE IN PERCENT BY VOLUME.
| 4. FIRST-AID MEASURES | |
INHALATION:
IMMEDIATELY REMOVE FROM FURTHER EXPOSURE. GET IMMEDIATE MEDICAL ASSISTANCE.
FOR THOSE PROVIDING ASSISTANCE, AVOID EXPOSURE TO YOURSELF OR OTHERS. USE
ADEQUATE RESPIRATORY PROTECTION. GIVE SUPPLEMENTAL OXYGEN, IF AVAILABLE.
IF BREATHING HAS STOPPED, ASSIST VENTILATION WITH A MECHANICAL DEVICE OR
USE MOUTH-TO-MOUTH RESUSCITATION.
SKIN CONTACT:
CONTACT WITH DUST: REMOVE CONTAMINATED CLOTHES AND RINSE SKIN THOROUGHLY
WITH WATER FOR AT LEAST 15 MINUTES. IF SKIN RASH OR AN ALLERGIC SKIN
REACTION DEVELOPS, GET MEDICAL ATTENTION.
EYE CONTACT:
CONTACT WITH DUST: RINSE IMMEDIATELY WITH PLENTY OF WATER FOR AT LEAST 15
MINUTES. REMOVE ANY CONTACT LENSES. GET MEDICAL ATTENTION IF IRRITATION
DEVELOPS OR PERSISTS.
INGESTION:
IMMEDIATELY RINSE MOUTH AND DRINK A CUPFUL OF WATER. NEVER GIVE ANYTHING BY
MOUTH TO A VICTIM WHO IS UNCONSCIOUS OR IS HAVING CONVULSIONS. ONLY INDUCE
VOMITING AT THE INSTRUCTION OF MEDICAL PERSONNEL. GET MEDICAL ATTENTION
IMMEDIATELY.
MOST IMPORTANT SYMPTOMS/EFFECTS, ACUTE AND DELAYED:
SYMPTOMS MAY INCLUDE REDNESS, OEDEMA, DRYING, DEFATTING AND CRACKING OF THE
SKIN. NAUSEA, VOMITING. DIARRHOEA. SYMPTOMS MAY INCLUDE STINGING, TEARING,
REDNESS, SWELLING, AND BLURRED VISION. ELEVATED TEMPERATURES OR MECHANICAL
ACTION MAY FORM DUST AND FUMES WHICH MAY BE IRRITATING TO THE EYE, MUCOUS
MEMBRANES AND RESPIRATORY TRACT. SYMPTOMS MAY INCLUDE COUGHING, DIFFICULTY
BREATHING AND SHORTNESS OF BREATH. OVEREXPOSURE TO COPPER FUMES MAY CAUSE
FEVER, CHILLS, CONGESTION AND HEADACHES.
INDICATION OF IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT NEEDED:
TREAT SYMPTOMATICALLY. EXPOSURE MAY AGGRAVATE PRE-EXISTING RESPIRATORY
DISORDERS. SYMPTOMS MAY BE DELAYED.
GENERAL INFORMATION:
SHOW THIS SAFETY DATA SHEET TO THE DOCTOR IN ATTENDANCE.
| 5. FIRE-FIGHTING MEASURES | |
SUITABLE EXTINGUISHING MEDIA:
EXTINGUISH WITH FOAM, CARBON DIOXIDE OR DRY POWDER. USE FIRE-EXTINGUISHING
MEDIA APPROPRIATE FOR SURROUNDING MATERIALS.
UNSUITABLE EXTINGUISHING MEDIA:
DO NOT USE WATER OR HALOGENATED EXTINGUISHING MEDIA.
SPECIFIC HAZARDS ARISING FROM THE CHEMICAL:
FIRE OR HIGH TEMPERATURES CREATE: METAL OXIDES.
SPECIAL PROTECTIVE EQUIPMENT AND PRECAUTIONS FOR FIREFIGHTERS:
SELF-CONTAINED BREATHING APPARATUS AND FULL PROTECTIVE CLOTHING MUST BE
WORN IN CASE OF FIRE.
FIRE FIGHTING EQUIPMENT/INSTRUCTIONS:
MOVE CONTAINERS FROM FIRE AREA IF YOU CAN DO IT WITHOUT RISK.
GENERAL FIRE HAZARDS:
SOLID METAL IS NOT FLAMMABLE; HOWEVER, FINELY DIVIDED METALLIC DUST OR
POWDER MAY FORM AN EXPLOSIVE MIXTURE WITH AIR.
| 6. ACCIDENTAL RELEASE MEASURES | |
PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
KEEP UNNECESSARY PERSONNEL AWAY. AVOID INHALATION OF DUST FROM THE SPILLED
MATERIAL. WEAR PROTECTIVE CLOTHING AS DESCRIBED IN SECTION 8 OF THIS SDS.
DO NOT TOUCH DAMAGED CONTAINERS OR SPILLED MATERIAL UNLESS WEARING
APPROPRIATE PROTECTIVE CLOTHING.
METHODS AND MATERIALS FOR CONTAINMENT AND CLEANING UP:
STOP LEAK IF YOU CAN DO SO WITHOUT RISK. LOCAL AUTHORITIES SHOULD BE
ADVISED IF SIGNIFICANT SPILLAGES CANNOT BE CONTAINED.
FOR A DRY MATERIAL SPILL, USE A HEPA (HIGH EFFICIENCY PARTICLE AIR) VACUUM
TO COLLECT MATERIAL AND PLACE IN A SEALABLE CONTAINER FOR DISPOSAL. AVOID
DUST FORMATION. RECOVER AND RECYCLE, IF PRACTICAL. KEEP OUT OF WATER
SUPPLIES AND SEWERS.
ENVIRONMENTAL PRECAUTIONS:
PREVENT FURTHER LEAKAGE OR SPILLAGE IF SAFE TO DO SO. DO NOT CONTAMINATE
WATER.
| 7. HANDLING AND STORAGE | |
PRECAUTIONS FOR SAFE HANDLING:
WEAR APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT (SEE SECTION 8). KEEP
FORMATION OF AIRBORNE DUSTS TO A MINIMUM. PROVIDE APPROPRIATE EXHAUST
VENTILATION AT PLACES WHERE DUST IS FORMED. AVOID INHALATION OF DUST AND
FUMES. AVOID CONTACT WITH SKIN AND EYES. DO NOT GET THIS MATERIAL ON
CLOTHING. DO NOT EAT, DRINK OR SMOKE WHEN USING THE PRODUCT. WASH
THOROUGHLY AFTER HANDLING. AVOID RELEASE TO THE ENVIRONMENT.
ANY SURFACE THAT COMES IN CONTACT WITH MOLTEN METAL MUST BE PREHEATED OR
SPECIALLY COATED AND RUST FREE. INADVERTENT CONTAMINANTS TO PRODUCT SUCH AS
MOISTURE, ICE, SNOW, GREASE, OR OIL CAN CAUSE AN EXPLOSION WHEN CHARGED TO
A MOLTEN METAL BATH OR METAL FURNACE (PREHEATING METAL WILL REMOVE MOISTURE
FROM PRODUCT).
CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPATIBILITIES:
STORE IN TIGHTLY CLOSED ORIGINAL CONTAINER IN A DRY, COOL AND
WELL-VENTILATED PLACE. STORE IN A CLOSED CONTAINER AWAY FROM INCOMPATIBLE
MATERIALS. KEEP OUT OF REACH OF CHILDREN. KEEP AWAY FROM FOOD, DRINK AND
ANIMAL FEEDING STUFFS.
| 8. EXPOSURE CONTROLS/PERSONAL PROTECTION | |
OCCUPATIONAL EXPOSURE LIMITS:
US. ACGIH THRESHOLD LIMIT VALUES:
COMPONENTS TYPE VALUE FORM
COPPER, ELEMENTAL TWA 1 MG/M3 DUST AND MIST.
(CAS 7440-50-8) 0.2 MG/M3 FUME.
PHOSPHOROUS (CAS 7723-14-0) TWA 0.1 MG/M3
SILVER, ELEMENTAL TWA 0.1 MG/M3 DUST AND FUME.
(CAS 7440-22-4)
CANADA. ALBERTA OELS (OCCUPATIONAL HEALTH & SAFETY CODE, SCHEDULE 1, TABLE
2):
COMPONENTS TYPE VALUE FORM
COPPER, ELEMENTAL TWA 1 MG/M3 DUST AND MIST.
(CAS 7440-50-8)
0.2 MG/M3 FUME.
PHOSPHOROUS (CAS 7723-14-0) TWA 0.1 MG/M3
SILVER, ELEMENTAL TWA 0.1 MG/M3
(CAS 7440-22-4)
CANADA. BRITISH COLUMBIA OELS. (OCCUPATIONAL EXPOSURE LIMITS FOR CHEMICAL
SUBSTANCES, OCCUPATIONAL HEALTH AND SAFETY REGULATION 296/97, AS AMENDED):
COMPONENTS TYPE VALUE FORM
COPPER, ELEMENTAL TWA 1 MG/M3 DUST AND MIST.
(CAS 7440-50-8) 0.2 MG/M3 FUME.
PHOSPHOROUS (CAS 7723-14-0) TWA 0.1 MG/M3
SILVER, ELEMENTAL STEL 0.03 MG/M3
(CAS 7440-22-4) TWA 0.01 MG/M3
CANADA. MANITOBA OELS (REG. 217/2006, THE WORKPLACE SAFETY AND HEALTH ACT):
COMPONENTS TYPE VALUE FORM
PHOSPHOROUS (CAS 7723-14-0) TWA 0.1 MG/M3
SILVER, ELEMENTAL TWA 0.1 MG/M3 DUST AND FUME.
(CAS 7440-22-4)
CANADA. ONTARIO OELS. (CONTROL OF EXPOSURE TO BIOLOGICAL OR CHEMICAL
AGENTS):
COMPONENTS TYPE VALUE FORM
COPPER, ELEMENTAL TWA 1 MG/M3 DUST AND FUME.
(CAS 7440-50-8) 0.2 MG/M3 FUME.
PHOSPHOROUS (CAS 7723-14-0) TWA 0.1 MG/M3
SILVER, ELEMENTAL TWA 0.1 MG/M3 DUST AND FUME.
(CAS 7440-22-4)
CANADA. QUEBEC OELS. (MINISTRY OF LABOR - REGULATION RESPECTING THE
QUALITY OF THE WORK ENVIRONMENT):
COMPONENTS TYPE VALUE FORM
COPPER, ELEMENTAL TWA 1 MG/M3 DUST AND MIST.
(CAS 7440-50-8) 0.2 MG/M3 FUME.
PHOSPHOROUS (CAS 7723-14-0) TWA 0.1 MG/M3
SILVER, ELEMENTAL TWA 0.1 MG/M3
(CAS 7440-22-4)
BIOLOGICAL LIMIT VALUES:
NO BIOLOGICAL EXPOSURE LIMITS NOTED FOR THE INGREDIENT(S).
EXPOSURE GUIDELINES: NO EXPOSURE STANDARDS ALLOCATED.
APPROPRIATE ENGINEERING CONTROLS:
PROVIDE ADEQUATE VENTILATION. OBSERVE OCCUPATIONAL EXPOSURE LIMITS AND
MINIMIZE THE RISK OF INHALATION OF DUST. KEEP MELTING/SOLDERING
TEMPERATURES AS LOW AS POSSIBLE TO MINIMIZE THE GENERATION OF FUME. SHOWER,
HAND AND EYE WASHING FACILITIES NEAR THE WORKPLACE ARE RECOMMENDED.
INDIVIDUAL PROTECTION MEASURES, SUCH AS PERSONAL PROTECTIVE EQUIPMENT:
EYE/FACE PROTECTION:
WEAR SAFETY GLASSES WITH SIDE SHIELDS (OR GOGGLES). WEAR A FACE SHIELD WHEN
WORKING WITH MOLTEN MATERIAL.
SKIN PROTECTION:
HAND PROTECTION: WEAR PROTECTIVE GLOVES (I.E. LATEX, NITRILE, NEOPRENE).
OTHER: CHEMICAL RESISTANT CLOTHING IS RECOMMENDED.
RESPIRATORY PROTECTION:
USE A RESPIRATOR WHEN LOCAL EXHAUST OR VENTILATION IS NOT ADEQUATE TO KEEP
EXPOSURES BELOW THE OEL. IN A CONFINED SPACE A SUPPLIED RESPIRATOR MAY BE
REQUIRED. SELECTION AND USE OF RESPIRATORY PROTECTIVE EQUIPMENT SHOULD BE
IN ACCORDANCE WITH OSHA GENERAL INDUSTRY STANDARD 29 CFR 1910.134; OR IN
CANADA WITH CSA STANDARD Z94.4. USE A NIOSH/MSHA APPROVED RESPIRATOR IF
THERE IS A RISK OF EXPOSURE TO DUST/FUME AT LEVELS EXCEEDING THE EXPOSURE
LIMITS.
THERMAL HAZARDS:
HEAT RESISTANT/INSULATED GLOVES AND CLOTHING ARE RECOMMENDED WHEN WORKING
WITH MOLTEN MATERIAL.
GENERAL HYGIENE CONSIDERATIONS:
ALWAYS OBSERVE GOOD PERSONAL HYGIENE MEASURES, SUCH AS WASHING AFTER
HANDLING THE MATERIAL AND BEFORE EATING, DRINKING, AND/OR SMOKING.
ROUTINELY WASH WORK CLOTHING AND PROTECTIVE EQUIPMENT TO REMOVE
CONTAMINANTS.
| 9. PHYSICAL AND CHEMICAL PROPERTIES | |
APPEARANCE:
PHYSICAL STATE: SOLID.
FORM: ROD. STRIPS.
COLOR: COPPER.
ODOR: ODORLESS.
ODOR THRESHOLD: NOT APPLICABLE.
PH: NOT APPLICABLE.
MELTING POINT/FREEZING POINT: 1083 DEG. C (1981.4 DEG. F) COPPER
INITIAL BOILING POINT AND BOILING RANGE: 2300 DEG. C (4172 DEG. F) COPPER
FLASH POINT: NOT APPLICABLE.
EVAPORATION RATE: NOT AVAILABLE.
FLAMMABILITY (SOLID, GAS):
FINE PARTICLES MAY FORM EXPLOSIVE MIXTURES WITH AIR.
UPPER/LOWER FLAMMABILITY OR EXPLOSIVE LIMITS:
FLAMMABILITY LIMIT - LOWER (%): NOT AVAILABLE.
FLAMMABILITY LIMIT - UPPER (%): NOT AVAILABLE.
EXPLOSIVE LIMIT - LOWER (%): NOT AVAILABLE.
EXPLOSIVE LIMIT - LOWER (%) TEMPERATURE: NOT APPLICABLE.
EXPLOSIVE LIMIT - UPPER (%): NOT AVAILABLE.
EXPLOSIVE LIMIT - UPPER (%) TEMPERATURE: NOT APPLICABLE.
VAPOR PRESSURE: 1 @ 1628 DEG. C COPPER
VAPOR DENSITY: NOT APPLICABLE.
RELATIVE DENSITY: 8.9 (H2O=1) COPPER
SOLUBILITY(IES):
SOLUBILITY (WATER): NOT SOLUBLE
PARTITION COEFFICIENT (N-OCTANOL/WATER): NOT AVAILABLE.
AUTO-IGNITION TEMPERATURE: NOT APPLICABLE.
DECOMPOSITION TEMPERATURE: NOT AVAILABLE.
VISCOSITY: NOT AVAILABLE.
OTHER INFORMATION:
SPECIFIC GRAVITY: 8.9
| 10. STABILITY AND REACTIVITY | |
REACTIVITY:
THE PRODUCT IS NON-REACTIVE UNDER NORMAL CONDITIONS OF USE, STORAGE AND
TRANSPORT.
CHEMICAL STABILITY: MATERIAL IS STABLE UNDER NORMAL CONDITIONS.
POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION DOES NOT OCCUR.
CONDITIONS TO AVOID:
CONTACT WITH INCOMPATIBLE MATERIALS. AVOID MOLTEN METAL CONTACT WITH WATER.
INCOMPATIBLE MATERIALS:
STRONG ACIDS. OXIDIZERS. HALOGENS. ACID CHLORIDES.
HAZARDOUS DECOMPOSITION PRODUCTS:
TOXIC METAL OXIDES ARE EMITTED WHEN HEATED ABOVE THE MELTING POINT.
| 11. TOXICOLOGICAL INFORMATION | |
INFORMATION ON LIKELY ROUTES OF EXPOSURE:
INHALATION:
ELEVATED TEMPERATURES OR MECHANICAL ACTION MAY FORM DUST AND FUMES WHICH
MAY BE IRRITATING TO THE MUCOUS MEMBRANES AND RESPIRATORY TRACT. LUNG
DAMAGE AND POSSIBLE PULMONARY EDEMA CAN RESULT FROM DUST EXPOSURE.
INHALATION OF FUMES MAY CAUSE A FLU-LIKE ILLNESS CALLED METAL FUME FEVER.
SKIN CONTACT:
DUST MAY IRRITATE SKIN. CONTACT WITH MOLTEN MATERIAL MAY CAUSE THERMAL
BURNS.
EYE CONTACT:
ELEVATED TEMPERATURES OR MECHANICAL ACTION MAY FORM DUST AND FUMES WHICH
MAY BE IRRITATING TO THE EYE.
INGESTION:
INGESTION OF DUSTS GENERATED DURING WORKING OPERATIONS MAY CAUSE NAUSEA AND
VOMITING. COPPER POISONING CAN RESULT IN HEMOLYTIC ANEMIA AND KIDNEY, LIVER
AND SPLEEN DAMAGE.
SYMPTOMS RELATED TO THE PHYSICAL, CHEMICAL AND TOXICOLOGICAL
CHARACTERISTICS:
ELEVATED TEMPERATURES OR MECHANICAL ACTION MAY FORM DUST AND FUMES WHICH
MAY BE IRRITATING TO THE EYE, MUCOUS MEMBRANES AND RESPIRATORY TRACT.
CONTACT WITH MOLTEN MATERIAL MAY CAUSE THERMAL BURNS.
INFORMATION ON TOXICOLOGICAL EFFECTS:
ACUTE TOXICITY:
HIGH CONCENTRATIONS OF FRESHLY FORMED FUMES/DUSTS OF METAL OXIDES CAN
PRODUCE SYMPTOMS OF METAL FUME FEVER. WHEN HEATED, THE VAPORS/FUMES GIVEN
OFF MAY CAUSE RESPIRATORY TRACT IRRITATION. ACUTE OVEREXPOSURE TO COPPER
DUST/FUME CAN CAUSE IRRITATION OF THE EYES, NOSE, THROAT, AND SKIN AND
UNDER SEVERE FUME OVEREXPOSURE CAN CAUSE METAL FUME FEVER WITH FLU-LIKE
SYMPTOMS SUCH AS SWEET METAL TASTE, DRY THROAT, COUGHING, FEVER AND CHILLS,
TIGHT CHEST, DYSPNEA, HEADACHE, BLURRED VISION, BACK PAIN, NAUSEA,
VOMITING, FATIGUE. SYMPTOMS USUALLY DISAPPEAR WITHIN 24 HOURS. COPPER MAY
CAUSE SKIN AND HAIR DISCOLORATION. INHALATION OF COPPER DUSTS MAY CHANGE
THE GUMS AND MUCOUS LINING OF THE MOUTH WHICH IS GENERALLY ATTRIBUTABLE TO
LOCALIZED TISSUE EFFECT RATHER THAN GENERAL TOXICITY.
SKIN CORROSION/IRRITATION: DUST MAY IRRITATE SKIN.
SERIOUS EYE DAMAGE/EYE IRRITATION:
ELEVATED TEMPERATURES OR MECHANICAL ACTION MAY FORM DUST AND FUMES WHICH
MAY BE IRRITATING TO THE EYE.
RESPIRATORY OR SKIN SENSITIZATION:
RESPIRATORY SENSITIZATION: NO SENSITIZING EFFECTS KNOWN.
SKIN SENSITIZATION: NO SENSITIZING EFFECTS KNOWN.
GERM CELL MUTAGENICITY: NOT CLASSIFIED.
CARCINOGENICITY: NOT CLASSIFIABLE AS TO CARCINOGENICITY TO HUMANS.
REPRODUCTIVE TOXICITY: NOT CLASSIFIED.
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE: NOT CLASSIFIED.
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE: NOT CLASSIFIED.
ASPIRATION HAZARD: NOT RELEVANT, DUE TO THE FORM OF THE PRODUCT.
CHRONIC EFFECTS:
INGESTION OF SILVER MAY CAUSE A PERMANENTLY BENIGN BLUISH GRAY
DISCOLORATION TO THE SKIN (ARGYRIA).
FURTHER INFORMATION:
NO OTHER SPECIFIC ACUTE OR CHRONIC HEALTH IMPACT NOTED.
| 12. ECOLOGICAL INFORMATION | |
ECOTOXICITY:
ALLOYS IN MASSIVE FORMS PRESENT A LIMITED HAZARD FOR THE ENVIRONMENT.
PERSISTENCE AND DEGRADABILITY: THE PRODUCT IS NOT BIODEGRADABLE.
BIOACCUMULATIVE POTENTIAL: NO DATA AVAILABLE.
MOBILITY IN SOIL:
ALLOYS IN MASSIVE FORMS ARE NOT MOBILE IN THE ENVIRONMENT.
OTHER ADVERSE EFFECTS: NONE KNOWN.
| 13. DISPOSAL CONSIDERATIONS | |
DISPOSAL INSTRUCTIONS:
DISPOSE IN ACCORDANCE WITH ALL APPLICABLE REGULATIONS.
LOCAL DISPOSAL REGULATIONS:
DISPOSE OF IN ACCORDANCE WITH LOCAL REGULATIONS.
HAZARDOUS WASTE CODE:
WASTE CODES SHOULD BE ASSIGNED BY THE USER BASED ON THE APPLICATION FOR
WHICH THE PRODUCT WAS USED.
WASTE FROM RESIDUES / UNUSED PRODUCTS:
DISPOSE OF IN ACCORDANCE WITH LOCAL REGULATIONS. SCRAPPED MATERIAL SHOULD
BE SENT FOR REFINING TO RECOVER PRECIOUS METAL CONTENT. SOLID METAL AND
ALLOYS IN THE FORM OF PARTICLES MAY BE REACTIVE. ITS HAZARDOUS
CHARACTERISTICS, INCLUDING FIRE AND EXPLOSION, SHOULD BE DETERMINED PRIOR
TO DISPOSAL.
CONTAMINATED PACKAGING:
SINCE EMPTIED CONTAINERS MAY RETAIN PRODUCT RESIDUE, FOLLOW LABEL WARNINGS
EVEN AFTER CONTAINER IS EMPTIED.
| 14. TRANSPORT INFORMATION | |
TDG: NOT REGULATED AS DANGEROUS GOODS.
IATA: NOT REGULATED AS DANGEROUS GOODS.
IMDG: NOT REGULATED AS DANGEROUS GOODS.
TRANSPORT IN BULK ACCORDING TO ANNEX II OF MARPOL 73/78 AND THE IBC CODE:
NOT APPLICABLE.
| 15. REGULATORY INFORMATION | |
CANADIAN REGULATIONS:
THIS PRODUCT HAS BEEN CLASSIFIED IN ACCORDANCE WITH THE HAZARD CRITERIA OF
THE HPR AND THE SDS CONTAINS ALL THE INFORMATION REQUIRED BY THE HPR.
CONTROLLED DRUGS AND SUBSTANCES ACT: NOT REGULATED.
EXPORT CONTROL LIST (CEPA 1999, SCHEDULE 3): NOT LISTED.
GREENHOUSE GASES: NOT LISTED.
PRECURSOR CONTROL REGULATIONS:
PHOSPHOROUS (CAS 7723-14-0): CLASS A
INTERNATIONAL REGULATIONS:
STOCKHOLM CONVENTION: NOT APPLICABLE.
ROTTERDAM CONVENTION: NOT APPLICABLE.
KYOTO PROTOCOL: NOT APPLICABLE.
MONTREAL PROTOCOL: NOT APPLICABLE.
BASEL CONVENTION: NOT APPLICABLE.
INTERNATIONAL INVENTORIES:
COUNTRY(S) INVENTORY NAME ON INVENTORY
OR REGION (YES/NO)*
AUSTRALIA AUSTRALIAN INVENTORY OF CHEMICAL YES
SUBSTANCES (AICS)
CANADA DOMESTIC SUBSTANCES LIST (DSL) YES
CANADA NON-DOMESTIC SUBSTANCES LIST (NDSL) NO
CHINA INVENTORY OF EXISTING CHEMICAL YES
SUBSTANCES IN CHINA (IECSC)
EUROPE EUROPEAN INVENTORY OF EXISTING COMMERCIAL YES
CHEMICAL SUBSTANCES (EINECS)
EUROPE EUROPEAN LIST OF NOTIFIED CHEMICAL NO
SUBSTANCES (ELINCS)
JAPAN INVENTORY OF EXISTING AND NEW CHEMICAL NO
SUBSTANCES (ENCS)
KOREA EXISTING CHEMICALS LIST (ECL) YES
NEW ZEALAND NEW ZEALAND INVENTORY YES
PHILIPPINES PHILIPPINE INVENTORY OF CHEMICALS AND YES
CHEMICAL SUBSTANCES (PICCS)
UNITED STATES TOXIC SUBSTANCES CONTROL ACT (TSCA) YES
& PUERTO RICO INVENTORY
*A "YES" INDICATES THIS PRODUCT COMPLIES WITH THE INVENTORY REQUIREMENTS
ADMINISTERED BY THE GOVERNING COUNTRY(S).
A "NO" INDICATES THAT ONE OR MORE COMPONENTS OF THE PRODUCT ARE NOT LISTED
OR EXEMPT FROM LISTING ON THE INVENTORY ADMINISTERED BY THE GOVERNING
COUNTRY(S).
| 16. OTHER INFORMATION | |
ISSUE DATE: 26-JULY-2016
REVISION DATE:
VERSION NO.: 01
REFERENCES:
EPA: AQUIRE DATABASE
NLM: HAZARDOUS SUBSTANCES DATA BASE
US. IARC MONOGRAPHS ON OCCUPATIONAL EXPOSURES TO CHEMICAL AGENTS
HSDB(R*) - HAZARDOUS SUBSTANCES DATA BANK
JIS Z 7250:
2005 SAFETY DATA SHEET FOR CHEMICAL PRODUCTS-PART 1:
CONTENT AND ORDER OF SECTIONS JCIA GHS GUIDELINE, OCTOBER 2008
IARC MONOGRAPHS. OVERALL EVALUATION OF CARCINOGENICITY
NATIONAL TOXICOLOGY PROGRAM (NTP) REPORT ON CARCINOGENS
ACGIH DOCUMENTATION OF THE THRESHOLD LIMIT VALUES AND BIOLOGICAL EXPOSURE
INDICES
GOST 30333-2007 - CHEMICAL PRODUCTION SAFETY PASSPORT. GENERAL REQUIREMENTS
DISCLAIMER:
ALL INFORMATION IN THIS SAFETY DATA SHEET IS BELIEVED TO BE ACCURATE AND
RELIABLE. HOWEVER, NO GUARANTEE OR WARRANTY OF ANY KIND IS MADE WITH REGARD
TO THE ACCURACY OF INFORMATION OR THE SUITABILITY OF THE RECOMMENDATIONS
CONTAINED HEREIN. IT IS THE USER'S RESPONSIBILITY TO ASSESS THE SAFETY AND
TOXICITY OF THIS PRODUCT UNDER THEIR OWN CONDITIONS OF USE AND TO COMPLY
WITH ALL APPLICABLE LAWS AND REGULATIONS.
926913
VERSION #: 01
SDS CANADA