| Common Name: | DEVCON DEV-THANE 5 GREY [1:1] |
| Manufacturer: | ITW POLYMERS ADHESIVES, NORTH AMERICA |
| SDS Revision Date: | 9/10/2015 |
| SDS Format: | GHS-US |
| Item Number(s): | 3DPH8 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
DEVCON(R*)
KIT - SAFETY DATA SHEET
PRODUCT IDENTIFIER USED ON THE LABEL:
KIT NAME: DEVCON(R*) DEV-THANE 5(TM) GREY [1:1]
STOCK NO.: 14503
OTHER MEANS OF IDENTIFICATION:
RECOMMENDED USE OF THE CHEMICAL AND RESTRICTIONS ON USE:
CHEMICAL MANUFACTURER ADDRESS AND TELEPHONE NUMBER:
MANUFACTURER NAME: ITW POLYMERS ADHESIVES, NORTH AMERICA
ADDRESS:
30 ENDICOTT STREET
DANVERS, MA 01923
COMPONENT LIST:
COMPONENT B: PU 990B
COMPONENT A: DEV-THANE I RESIN
KIT SDS REVISION DATE: 9/10/2015
COMPONENT B - SDS
| SECTION 1: IDENTIFICATION |  |
PRODUCT IDENTIFIER USED ON THE LABEL:
PRODUCT NAME: PU 990B
OTHER MEANS OF IDENTIFICATION:
RECOMMENDED USE OF THE CHEMICAL AND RESTRICTIONS ON USE:
CHEMICAL MANUFACTURER ADDRESS AND TELEPHONE NUMBER:
MANUFACTURER NAME: ITW
ADDRESS:
30 ENDICOTT STREET
DANVERS, MA 01923
GENERAL PHONE NUMBER: (978) 777-1100
EMERGENCY PHONE NUMBER:
EMERGENCY PHONE NUMBER: (800) 424-9300
CHEMTREC:
FOR EMERGENCIES IN THE US, CALL CHEMTREC: 800-424-9300
| SECTION 2: HAZARD(S) IDENTIFICATION | |
CLASSIFICATION OF THE CHEMICAL IN ACCORDANCE WITH CFR 1910.1200(D)(F):
GHS PICTOGRAMS: EXCLAMATION MARK
SIGNAL WORD: WARNING.
GHS CLASS:
EYE IRRITATION. CATEGORY 2.
SKIN IRRITATION. CATEGORY 2.
SPECIFIC TARGET ORGAN TOXICITY - STOT, SINGLE EXPOSURE SE. CATEGORY 3.
HAZARD STATEMENTS:
H319: CAUSES SERIOUS EYE IRRITATION.
H315: CAUSES SKIN IRRITATION.
H335: MAY CAUSE RESPIRATORY IRRITATION.
PRECAUTIONARY STATEMENTS:
P261: AVOID BREATHING DUST/FUME/GAS/MIST/VAPOURS/SPRAY.
P264: WASH HANDS THOROUGHLY AFTER HANDLING.
P271: USE ONLY OUTDOORS OR IN A WELL-VENTILATED AREA.
P280:
WEAR PROTECTIVE GLOVES/PROTECTIVE CLOTHING/EYE PROTECTION/FACE PROTECTION.
P302+P352:
IF ON SKIN: WASH WITH PLENTY OF WATER.
P304+P340:
IF INHALED:
REMOVE VICTIM TO FRESH AIR AND KEEP AT REST IN A POSITION COMFORTABLE FOR
BREATHING.
P305+P351+P338:
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES,
IF PRESENT AND EASY TO DO. CONTINUE RINSING.
P312: CALL A POISON CENTER OR DOCTOR/PHYSICIAN IF YOU FEEL UNWELL.
P321 - P332+P313:
IF SKIN IRRITATION OCCURS: GET MEDICAL ADVICE/ATTENTION.
P337+P313:
IF EYE IRRITATION PERSISTS: GET MEDICAL ADVICE/ATTENTION.
P362+P364: TAKE OFF CONTAMINATED CLOTHING AND WASH IT BEFORE REUSE.
P403+P233: STORE IN A WELL-VENTILATED PLACE. KEEP CONTAINER TIGHTLY CLOSED.
P405: STORE LOCKED UP.
P501:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH LOCAL, STATE, FEDERAL AND
PROVINCIAL REGULATIONS.
HAZARDS NOT OTHERWISE CLASSIFIED THAT HAVE BEEN IDENTIFIED DURING THE
CLASSIFICATION PROCESS:
EMERGENCY OVERVIEW:
WARNING!
IRRITANT.
ROUTE OF EXPOSURE: EYES. SKIN. INHALATION. INGESTION.
POTENTIAL HEALTH EFFECTS:
EYE:
CAN CAUSE MODERATE IRRITATION, BURNING SENSATION, TEARING, REDNESS, AND
SWELLING. OVEREXPOSURE MAY CAUSE LACRIMATION, CONJUNCTIVITIS, CORNEAL
DAMAGE AND PERMANENT INJURY.
SKIN:
CAN CAUSE SKIN IRRITATION; ITCHING, REDNESS, RASHES, HIVES, BURNING, AND
SWELLING.
INHALATION:
RESPIRATORY TRACT IRRITANT. HIGH CONCENTRATION MAY CAUSE DIZZINESS,
HEADACHE, AND ANESTHETIC EFFECTS.
INGESTION:
CAUSES IRRITATION, A BURNING SENSATION OF THE MOUTH, THROAT AND
GASTROINTESTINAL TRACT AND ABDOMINAL PAIN.
CHRONIC HEALTH EFFECTS:
PROLONGED SKIN CONTACT MAY LEAD TO BURNING ASSOCIATED WITH SEVERE
REDDENING, SWELLING, AND POSSIBLE TISSUE DESTRUCTION.
SIGNS/SYMPTOMS:
OVEREXPOSURE CAN CAUSE HEADACHES, DIZZINESS, NAUSEA, AND VOMITING.
TARGET ORGANS: EYES. SKIN. RESPIRATORY SYSTEM. DIGESTIVE SYSTEM.
AGGRAVATION OF PRE-EXISTING CONDITIONS:
INDIVIDUALS WITH PRE-EXISTING SKIN DISORDERS, ASTHMA, ALLERGIES OR KNOWN
SENSITIZATION MAY BE MORE SUSCEPTIBLE TO THE EFFECTS OF THIS PRODUCT.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
MIXTURES:
CHEMICAL NAME CAS# INGREDIENT PERCENT EC NUM.
PROPRIETARY INGREDIENT(S) TRADE SECRET 90 - 100 BY WEIGHT
| SECTION 4: FIRST AID MEASURES | |
DESCRIPTION OF NECESSARY MEASURES:
EYE CONTACT:
IMMEDIATELY FLUSH EYES WITH PLENTY OF WATER FOR AT LEAST 15 TO 20 MINUTES.
ENSURE ADEQUATE FLUSHING OF THE EYES BY SEPARATING THE EYELIDS WITH
FINGERS. GET IMMEDIATE MEDICAL ATTENTION.
SKIN CONTACT:
IMMEDIATELY WASH SKIN WITH PLENTY OF SOAP AND WATER FOR 15 TO 20 MINUTES,
WHILE REMOVING CONTAMINATED CLOTHING AND SHOES. GET MEDICAL ATTENTION IF
IRRITATION DEVELOPS OR PERSISTS.
INHALATION:
IF INHALED, REMOVE TO FRESH AIR. IF NOT BREATHING, GIVE ARTIFICIAL
RESPIRATION OR GIVE OXYGEN BY TRAINED PERSONNEL. SEEK IMMEDIATE MEDICAL
ATTENTION.
INGESTION:
IF SWALLOWED, DO NOT INDUCE VOMITING. CALL A PHYSICIAN OR POISON CONTROL
CENTER IMMEDIATELY. NEVER GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON.
| SECTION 5: FIRE FIGHTING MEASURES | |
SUITABLE AND UNSUITABLE EXTINGUISHING MEDIA:
SUITABLE EXTINGUISHING MEDIA:
USE DRY CHEMICAL, CARBON DIOXIDE, FOAM OR WATER FOG
SPECIAL PROTECTIVE EQUIPMENT AND PRECAUTIONS FOR FIRE-FIGHTERS:
PROTECTIVE EQUIPMENT:
AS IN ANY FIRE, WEAR SELF-CONTAINED BREATHING APPARATUS (SCBA), MSHA/NIOSH
(APPROVED OR EQUIVALENT) AND FULL PROTECTIVE GEAR.
FIRE FIGHTING INSTRUCTIONS:
EVACUATE AREA OF UNPROTECTED PERSONNEL. USE COLD WATER SPRAY TO COOL FIRE
EXPOSED CONTAINERS TO MINIMIZE RISK OF RUPTURE. DO NOT ENTER CONFINED FIRE
SPACE WITHOUT FULL PROTECTIVE GEAR. IF POSSIBLE, CONTAIN FIRE RUN-OFF
WATER. DURING FIRE, IRRITATING AND TOXIC GASES MAY BE GENERATED BY THERMAL
DECOMPOSITION OR COMBUSTION
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
PERSONAL PRECAUTIONS:
EVACUATE AREA AND KEEP UNNECESSARY AND UNPROTECTED PERSONNEL FROM ENTERING
THE SPILL AREA.
ENVIRONMENTAL PRECAUTIONS:
ENVIRONMENTAL PRECAUTIONS:
AVOID RUNOFF INTO STORM SEWERS, DITCHES, AND WATERWAYS.
METHODS AND MATERIALS FOR CONTAINMENT AND CLEANING UP:
SPILL CLEANUP MEASURES:
ABSORB SPILL WITH INERT MATERIAL (E,G., DRY SAND OR EARTH), THEN PLACE IN
A CHEMICAL WASTE CONTAINER.
PROVIDE VENTILATION. CLEAN UP SPILLS IMMEDIATELY OBSERVING PRECAUTIONS IN
THE PROTECTIVE EQUIPMENT SECTION. AFTER REMOVAL, FLUSH SPILL AREA WITH SOAP
AND WATER TO REMOVE TRACE RESIDUE.
AVOID PERSONAL CONTACT AND BREATHING VAPORS OR MISTS. VENTILATE AREA. USE
PROPER PERSONAL PROTECTIVE EQUIPMENT AS LISTED IN SECTION 8.
REFERENCE TO OTHER SECTIONS:
OTHER PRECAUTIONS: PUMP OR SHOVEL TO STORAGE/SALVAGE VESSELS.
| SECTION 7: HANDLING AND STORAGE | |
PRECAUTIONS FOR SAFE HANDLING:
HANDLING:
USE WITH ADEQUATE VENTILATION. AVOID BREATHING VAPOR, AEROSOL OR MIST.
HYGIENE PRACTICES: WASH THOROUGHLY AFTER HANDLING.
SPECIAL HANDLING PROCEDURES:
PROVIDE APPROPRIATE VENTILATION/RESPIRATORY PROTECTION AGAINST
DECOMPOSITION PRODUCTS (SEE SECTION 10) DURING WELDING/FLAME CUTTING
OPERATIONS AND TO PROTECT AGAINST DUST DURING SANDING/GRINDING OF CURED
PRODUCT.
CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPATIBILITIES:
STORAGE:
STORE IN A COOL, DRY, WELL VENTILATED AREA AWAY FROM SOURCES OF HEAT AND
INCOMPATIBLE MATERIALS. KEEP CONTAINER TIGHTLY CLOSED WHEN NOT IN USE.
| SECTION 8: EXPOSURE CONTROLS, PERSONAL PROTECTION | |
EXPOSURE GUIDELINES:
APPROPRIATE ENGINEERING CONTROLS:
ENGINEERING CONTROLS:
USE APPROPRIATE ENGINEERING CONTROL SUCH AS PROCESS ENCLOSURES, LOCAL
EXHAUST VENTILATION, OR OTHER ENGINEERING CONTROLS TO CONTROL AIRBORNE
LEVELS BELOW RECOMMENDED EXPOSURE LIMITS. GOOD GENERAL VENTILATION SHOULD
BE SUFFICIENT TO CONTROL AIRBORNE LEVELS. WHERE SUCH SYSTEMS ARE NOT
EFFECTIVE WEAR SUITABLE PERSONAL PROTECTIVE EQUIPMENT, WHICH PERFORMS
SATISFACTORILY AND MEETS OSHA OR OTHER RECOGNIZED STANDARDS. CONSULT WITH
LOCAL PROCEDURES FOR SELECTION, TRAINING, INSPECTION AND MAINTENANCE OF
THE PERSONAL PROTECTIVE EQUIPMENT.
INDIVIDUAL PROTECTION MEASURES:
EYE/FACE PROTECTION:
WEAR APPROPRIATE PROTECTIVE GLASSES OR SPLASH GOGGLES AS DESCRIBED BY
29 CFR 1910.133, OSHA EYE AND FACE PROTECTION REGULATION, OR THE EUROPEAN
STANDARD EN 166.
SKIN PROTECTION DESCRIPTION:
WEAR APPROPRIATE PROTECTIVE GLOVES AND OTHER PROTECTIVE APPAREL TO PREVENT
SKIN CONTACT. CONSULT MANUFACTURER'S DATA FOR PERMEABILITY DATA.
RESPIRATORY PROTECTION:
A NIOSH APPROVED AIR-PURIFYING RESPIRATOR WITH AN ORGANIC VAPOR CARTRIDGE
OR CANISTER MAY BE PERMISSIBLE UNDER CERTAIN CIRCUMSTANCES WHERE AIRBORNE
CONCENTRATIONS ARE EXPECTED TO EXCEED EXPOSURE LIMITS. PROTECTION PROVIDED
BY AIR PURIFYING RESPIRATORS IS LIMITED. USE A POSITIVE PRESSURE AIR
SUPPLIED RESPIRATOR IF THERE IS ANY POTENTIAL FOR AN UNCONTROLLED RELEASE,
EXPOSURE LEVELS ARE NOT KNOWN, OR ANY OTHER CIRCUMSTANCES WHERE AIR
PURIFYING RESPIRATORS MAY NOT PROVIDE ADEQUATE PROTECTION.
OTHER PROTECTIVE:
FACILITIES STORING OR UTILIZING THIS MATERIAL SHOULD BE EQUIPPED WITH AN
EYEWASH AND A DELUGE SHOWER SAFETY STATION.
NOTES: ONLY ESTABLISHED PEL AND TLV VALUES FOR THE INGREDIENTS ARE LISTED.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
PHYSICAL AND CHEMICAL PROPERTIES:
PHYSICAL STATE APPEARANCE: LIQUID.
COLOR: GRAY
ODOR: MILD.
BOILING POINT: NOT DETERMINED.
MELTING POINT: NOT DETERMINED.
SPECIFIC GRAVITY: 1.4
SOLUBILITY: NEGLIGIBLE.
VAPOR DENSITY: >1 (AIR = 1)
VAPOR PRESSURE: NOT DETERMINED.
PERCENT VOLATILE: NOT DETERMINED.
EVAPORATION RATE: NOT DETERMINED.
PH: NOT DETERMINED.
MOLECULAR FORMULA: MIXTURE
MOLECULAR WEIGHT: MIXTURE
FLASH POINT: >325 DEG. F (162.7 DEG. C)
FLASH POINT METHOD: PENSKY-MARTENS CLOSED CUP
LOWER FLAMMABLE/EXPLOSIVE LIMIT: NOT DETERMINED.
UPPER FLAMMABLE/EXPLOSIVE LIMIT: NOT DETERMINED.
AUTO IGNITION TEMPERATURE: NOT DETERMINED.
VOC CONTENT: NOT DETERMINED.
9.2. OTHER INFORMATION:
PERCENT SOLIDS BY WEIGHT: NOT DETERMINED.
| SECTION 10: STABILITY AND REACTIVITY | |
CHEMICAL STABILITY:
CHEMICAL STABILITY: STABLE UNDER NORMAL TEMPERATURES AND PRESSURES.
POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION: NOT REPORTED.
CONDITIONS TO AVOID:
CONDITIONS TO AVOID:
EXTREME HEAT, SPARKS, AND OPEN FLAME. INCOMPATIBLE MATERIALS, OXIDIZERS
AND OXIDIZING CONDITIONS.
INCOMPATIBLE MATERIALS:
INCOMPATIBLE MATERIALS: OXIDIZING AGENTS. STRONG ACIDS AND ALKALIS.
HAZARDOUS DECOMPOSITION PRODUCTS:
SPECIAL DECOMPOSITION PRODUCTS:
CARBON DIOXIDE, CARBON MONOXIDE, ALDEHYDES, ACIDS AND OTHER ORGANIC
SUBSTANCES MAY BE FORMED
| SECTION 11: TOXICOLOGICAL INFORMATION | |
TOXICOLOGICAL INFORMATION:
PROPRIETARY INGREDIENT(S):
EYE: NO RELEVANT TOXICOLOGICAL DATA WERE AVAILABLE.
SKIN: NO RELEVANT TOXICOLOGICAL DATA WERE AVAILABLE.
INHALATION: NO RELEVANT TOXICOLOGICAL DATA WERE AVAILABLE.
INGESTION: NO RELEVANT TOXICOLOGICAL DATA WERE AVAILABLE.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICITY:
ECOTOXICITY: NO ECOTOXICITY DATA WAS FOUND FOR THE PRODUCT.
ENVIRONMENTAL FATE: NO ENVIRONMENTAL INFORMATION FOUND FOR THIS PRODUCT.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
DESCRIPTION OF WASTE:
WASTE DISPOSAL:
CONSULT WITH THE US EPA GUIDELINES LISTED IN 40 CFR PART 261.3 FOR THE
CLASSIFICATIONS OF HAZARDOUS WASTE PRIOR TO DISPOSAL. FURTHERMORE, CONSULT
WITH YOUR STATE AND LOCAL WASTE REQUIREMENTS OR GUIDELINES, IF APPLICABLE,
TO ENSURE COMPLIANCE. ARRANGE DISPOSAL IN ACCORDANCE TO THE EPA AND/OR
STATE AND LOCAL GUIDELINES.
RCRA NUMBER: NOT DETERMINED.
| SECTION 14: TRANSPORT INFORMATION | |
DOT SHIPPING NAME: REFER TO BILL OF LADING
DOT UN NUMBER: REFER TO BILL OF LADING
IATA SHIPPING NAME: REFER TO BILL OF LADING
IATA UN NUMBER: REFER TO BILL OF LADING
IMDG UN NUMBER: REFER TO BILL OF LADING
IMDG SHIPPING NAME: REFER TO BILL OF LADING
| SECTION 15: REGULATORY INFORMATION | |
SAFETY, HEALTH AND ENVIRONMENTAL REGULATIONS SPECIFIC FOR THE PRODUCT:
CANADIAN REGULATIONS.:
WHMIS HAZARD CLASS(ES): NONE.
ALL COMPONENTS OF THIS PRODUCT ARE ON THE CANADIAN DOMESTIC SUBSTANCES
LIST.
| SECTION 16: ADDITIONAL INFORMATION | |
HMIS RATINGS:
HMIS HEALTH HAZARD 1
HMIS FIRE HAZARD 1
HMIS REACTIVITY 0
HMIS PERSONAL PROTECTION X
HEALTH HAZARD 1
FIRE HAZARD 1
REACTIVITY 0
PERSONAL PROTECTION X
SDS REVISION DATE: JULY 28, 2015
SDS REVISION NOTES: GHS UPDATE
SDS FORMAT: IN ACCORDANCE TO OSHA GHS 1910.1200
SDS AUTHOR: ACTIO CORPORATION
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. ITW POLYMERS ADHESIVES, NA, MAKES NO WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF
PERFORMANCE OR USAGE OF TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER
THE ITW POLYMERS ADHESIVES, NA PRODUCT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION. GIVEN THE VARIETY OF
FACTORS THAT CAN AFFECT THE USE AND APPLICATION OF A ITW POLYMERS
ADHESIVES, NA PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE ITW
POLYMERS ADHESIVES, NA PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A
PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
ITW POLYMERS ADHESIVES, NA PROVIDES INFORMATION IN ELECTRONIC FORM AS A
SERVICE TO ITS CUSTOMERS. DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC
TRANSFER MAY HAVE RESULTED IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS
INFORMATION, ITW POLYMERS ADHESIVES, NA MAKES NO REPRESENTATIONS AS TO ITS
COMPLETENESS OR ACCURACY. IN ADDITION, INFORMATION OBTAINED FROM A DATABASE
MAY NOT BE AS CURRENT AS THE INFORMATION IN THE MSDS AVAILABLE DIRECTLY
FROM ITW POLYMERS ADHESIVES, NA
COPYRIGHT(C) 1996-2018 ENVIANCE. ALL RIGHTS RESERVED.
COMPONENT A - SDS
| SECTION 1: IDENTIFICATION | |
PRODUCT IDENTIFIER USED ON THE LABEL:
PRODUCT NAME: DEV-THANE I RESIN
OTHER MEANS OF IDENTIFICATION:
RECOMMENDED USE OF THE CHEMICAL AND RESTRICTIONS ON USE:
CHEMICAL MANUFACTURER ADDRESS AND TELEPHONE NUMBER:
MANUFACTURER NAME: ITW
ADDRESS:
30 ENDICOTT STREET
DANVERS, MA 01923
GENERAL PHONE NUMBER: (978) 777-1100
EMERGENCY PHONE NUMBER:
EMERGENCY PHONE NUMBER: (800) 424-9300
CHEMTREC:
FOR EMERGENCIES IN THE US, CALL CHEMTREC: 800-424-9300
| SECTION 2: HAZARD(S) IDENTIFICATION | |
CLASSIFICATION OF THE CHEMICAL IN ACCORDANCE WITH CFR 1910.1200(D)(F):
GHS PICTOGRAMS:
SKULLS AND CROSSBONES
HEALTH HAZARD
EXCLAMATION MARK
SIGNAL WORD: DANGER.
GHS CLASS:
ACUTE INHALATION TOXICITY. CATEGORY 2.
RESPIRATORY SENSITISATION. CATEGORY 1.
SPECIFIC TARGET ORGAN TOXICITY - STOT REPEATED EXPOSURE RE. CATEGORY 2
(INHALATION, RESPIRATORY SYSTEM).
EYE IRRITATION. CATEGORY 2.
SKIN IRRITATION. CATEGORY 2.
SKIN SENSITIZATION. CATEGORY 1.
SPECIFIC TARGET ORGAN TOXICITY - STOT, SINGLE EXPOSURE SE. CATEGORY 3.
HAZARD STATEMENTS:
H330: FATAL IF INHALED.
H334:
MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
H373: MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.
H319: CAUSES SERIOUS EYE IRRITATION.
H315: CAUSES SKIN IRRITATION.
H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
H335: MAY CAUSE RESPIRATORY IRRITATION.
PRECAUTIONARY STATEMENTS:
P260: DO NOT BREATHE DUST/FUME/GAS/MIST/VAPOURS/SPRAY.
P261: AVOID BREATHING DUST/FUME/GAS/MIST/VAPOURS/SPRAY.
P264: WASH HANDS THOROUGHLY AFTER HANDLING.
P271: USE ONLY OUTDOORS OR IN A WELL-VENTILATED AREA.
P272:
CONTAMINATED WORK CLOTHING SHOULD NOT BE ALLOWED OUT OF THE WORKPLACE.
P280:
WEAR PROTECTIVE GLOVES/PROTECTIVE CLOTHING/EYE PROTECTION/FACE PROTECTION.
P284: IN CASE OF INADEQUATE VENTILATION WEAR RESPIRATORY PROTECTION.
P302+P352:
IF ON SKIN: WASH WITH PLENTY OF WATER.
P304+P340:
IF INHALED:
REMOVE VICTIM TO FRESH AIR AND KEEP AT REST IN A POSITION COMFORTABLE FOR
BREATHING.
P305+P351+P338:
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES,
IF PRESENT AND EASY TO DO. CONTINUE RINSING.
P310: IMMEDIATELY CALL A POISON CENTER OR DOCTOR/PHYSICIAN.
P312: CALL A POISON CENTER OR DOCTOR/PHYSICIAN IF YOU FEEL UNWELL.
P314: GET MEDICAL ADVICE/ATTENTION IF YOU FEEL UNWELL.
P320: SPECIFIC TREATMENT IS URGENT (SEE... ON THIS LABEL).
P321: SPECIFIC TREATMENT (SEE... ON THIS LABEL).
P332+P313:
IF SKIN IRRITATION OCCURS: GET MEDICAL ADVICE/ATTENTION.
P333+P313:
IF SKIN IRRITATION OR RASH OCCURS: GET MEDICAL ADVICE/ATTENTION.
P337+P313:
IF EYE IRRITATION PERSISTS: GET MEDICAL ADVICE/ATTENTION.
P342+P311:
IF EXPERIENCING RESPIRATORY SYMPTOMS:
CALL A POISON CENTER OR DOCTOR/PHYSICIAN.
P362+P364: TAKE OFF CONTAMINATED CLOTHING AND WASH IT BEFORE REUSE.
P403+P233:
STORE IN A WELL-VENTILATED PLACE. KEEP CONTAINER TIGHTLY CLOSED.
P405: STORE LOCKED UP.
P501:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH LOCAL, STATE, FEDERAL AND
PROVINCIAL REGULATIONS.
HAZARDS NOT OTHERWISE CLASSIFIED THAT HAVE BEEN IDENTIFIED DURING THE
CLASSIFICATION PROCESS:
ROUTE OF EXPOSURE: EYES. SKIN. INHALATION. INGESTION.
POTENTIAL HEALTH EFFECTS:
EYE:
CAN CAUSE MODERATE IRRITATION, BURNING SENSATION, TEARING, REDNESS, AND
SWELLING. OVEREXPOSURE MAY CAUSE LACRIMATION, CONJUNCTIVITIS, CORNEAL
DAMAGE AND PERMANENT INJURY.
SKIN:
CAN CAUSE SKIN IRRITATION; ITCHING, REDNESS, RASHES, HIVES, BURNING, AND
SWELLING. ALLERGIC REACTIONS ARE POSSIBLE.
MAY CAUSE SKIN SENSITIZATION, AN ALLERGIC REACTION, WHICH BECOMES EVIDENT
ON REEXPOSURE TO THIS MATERIAL.
INHALATION:
MDI VAPORS AT CONCENTRATIONS ABOVE THE TLV CAN IRRITATE THE MUCOUS EMBRANES
IN THE RESPIRATORY TRACT (NOSE, THROAT, LUNGS) CAUSING A RUNNY NOSE, SOAR
THROAT, COUGHING, CHEST DISCOMFORT, SHORTNESS OF BREATH AND REDUCED LUNG
FUNCTION. PERSONS WITH PRE-EXISTING, NONSPECIFIC BRONCHIAL HYPERREACTIVITY
CAN RESPOND TO CONCENTRATIONS BELOW TLV WITH SIMILAR SYMPTOMS AS WELL AS
ASTHMA ATTACK. OVEREXPOSURE TO ISOCYANATES HAS ALSO BEEN REPORTED TO CAUSE
LUNG DAMAGE (INCLUDING DECREASE IN LUNG FUNCTION) WHICH MAY BE PERMANENT.
INGESTION:
CAUSES IRRITATION, A BURNING SENSATION OF THE MOUTH, THROAT AND
GASTROINTESTINAL TRACT AND ABDOMINAL PAIN.
CHRONIC HEALTH EFFECTS:
PROLONGED SKIN CONTACT MAY LEAD TO BURNING ASSOCIATED WITH SEVERE
REDDENING, SWELLING, AND POSSIBLE TISSUE DESTRUCTION.
SIGNS/SYMPTOMS:
OVEREXPOSURE CAN CAUSE HEADACHES, DIZZINESS, NAUSEA, AND VOMITING.
TARGET ORGANS: EYES. SKIN. RESPIRATORY SYSTEM. DIGESTIVE SYSTEM.
AGGRAVATION OF PRE-EXISTING CONDITIONS:
INDIVIDUALS WITH PRE-EXISTING SKIN DISORDERS, ASTHMA, ALLERGIES OR KNOWN
SENSITIZATION MAY BE MORE SUSCEPTIBLE TO THE EFFECTS OF THIS PRODUCT.
ISOCYANATE EXPOSURE LEVELS MUST BE MONITORED. MEDICAL SUPERVISION OF ALL
EMPLOYEES WHO HANDLE OR COME IN CONTACT WITH ISOCYANATES IS RECOMMENDED
(I.E. FEV, FVC). THIS SHOULD INCLUDE PRE-EMPLOYMENT AND PERIODIC MEDICAL
EXAMINATIONS.
PERSONS WITH ASTHMATIC-TYPE CONDITIONS, CHRONIC BRONCHITIS, OTHER CHRONIC
RESPIRATORY DISEASES, RECURRENT SKIN ECZEMA OR SENSITIZATION SHOULD BE
EXCLUDED FROM WORKING WITH THIS PRODUCT. ONCE SENSITIZED NO FURTHER
EXPOSURE CAN BE PERMITTED.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
MIXTURES:
CHEMICAL NAME CAS# INGREDIENT PERCENT EC NUM.
4,4'-DIPHENYLMETHANE DIISOCYANATE 101-68-8 90 - 100 BY WEIGHT
DIPHENYLMETHANE DIISOCYANATE 26447-40-5 1 - 10 BY WEIGHT
| SECTION 4: FIRST AID MEASURES | |
DESCRIPTION OF NECESSARY MEASURES:
EYE CONTACT:
IMMEDIATELY FLUSH EYES WITH PLENTY OF WATER FOR AT LEAST 15 TO 20 MINUTES.
ENSURE ADEQUATE FLUSHING OF THE EYES BY SEPARATING THE EYELIDS WITH
FINGERS. GET IMMEDIATE MEDICAL ATTENTION.
SKIN CONTACT:
IMMEDIATELY WASH SKIN WITH PLENTY OF SOAP AND WATER FOR 15 TO 20 MINUTES,
WHILE REMOVING CONTAMINATED CLOTHING AND SHOES. GET MEDICAL ATTENTION IF
IRRITATION DEVELOPS OR PERSISTS.
INHALATION:
IF INHALED, REMOVE TO FRESH AIR. IF NOT BREATHING, GIVE ARTIFICIAL
RESPIRATION OR GIVE OXYGEN BY TRAINED PERSONNEL. SEEK IMMEDIATE MEDICAL
ATTENTION.
INGESTION:
IF SWALLOWED, DO NOT INDUCE VOMITING. CALL A PHYSICIAN OR POISON CONTROL
CENTER IMMEDIATELY. NEVER GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON.
INDICATION OF IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT NEEDED:
NOTE TO PHYSICIANS:
ASTHMATIC TYPE SYMPTOMS MAY DEVELOP, WHICH MAY BE IMMEDIATE OR DELAYED FOR
SEVERAL HOURS.
| SECTION 5: FIRE FIGHTING MEASURES | |
SUITABLE AND UNSUITABLE EXTINGUISHING MEDIA:
SUITABLE EXTINGUISHING MEDIA:
FOR LARGE FIRES, ALCOHOL RESISTANT FOAMS (ATC TYPE) ARE PREFERRED IF
AVAILABLE. GENERAL PURPOSE SYNTHETIC FOAMS (INCLUDING AFFF) OR PROTEIN
FOAMS MAY FUNCTION BUT MUCH LESS EFFECTIVELY.
UNSUITABLE EXTINGUISHING MEDIA:
WATER IS NOT RECOMMENDED BUT MAY BE APPLIED IN VERY LARGE QUANTITIES AS A
FINE SPRAY WHEN OTHER EXTINGUISHING MEDIA ARE NOT AVAILABLE.
UNUSUAL FIRE HAZARDS:
DO NOT RESEAL CONTAINERS IF CONTAMINATED WITH WATER, RESIN WILL REACT WITH
WATER TO RELEASE CARBON DIOXIDE. AS A RESULT OF THE WATER CONTAMINATION,
PRESSURE WILL BUILD UP IN THE SEALED CONTAINER CAUSING IT TO RUPTURE.
SPECIAL PROTECTIVE EQUIPMENT AND PRECAUTIONS FOR FIRE-FIGHTERS:
PROTECTIVE EQUIPMENT:
AS IN ANY FIRE, WEAR SELF-CONTAINED BREATHING APPARATUS (SCBA), MSHA/NIOSH
(APPROVED OR EQUIVALENT) AND FULL PROTECTIVE GEAR.
FIRE FIGHTING INSTRUCTIONS:
EVACUATE AREA OF UNPROTECTED PERSONNEL. USE COLD WATER SPRAY TO COOL FIRE
EXPOSED CONTAINERS TO MINIMIZE RISK OF RUPTURE. DO NOT ENTER CONFINED FIRE
SPACE WITHOUT FULL PROTECTIVE GEAR. IF POSSIBLE, CONTAIN FIRE RUN-OFF
WATER.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
PERSONAL PRECAUTIONS:
EVACUATE AREA AND KEEP UNNECESSARY AND UNPROTECTED PERSONNEL FROM ENTERING
THE SPILL AREA.
ENVIRONMENTAL PRECAUTIONS:
ENVIRONMENTAL PRECAUTIONS:
AVOID RUNOFF INTO STORM SEWERS, DITCHES, AND WATERWAYS.
METHODS AND MATERIALS FOR CONTAINMENT AND CLEANING UP:
SPILL CLEANUP MEASURES:
ABSORB SPILL WITH INERT MATERIAL (E,G., DRY SAND OR EARTH), THEN PLACE IN
A CHEMICAL WASTE CONTAINER. PROVIDE VENTILATION. CLEAN UP SPILLS
IMMEDIATELY OBSERVING PRECAUTIONS IN THE PROTECTIVE EQUIPMENT SECTION.
NEUTRALIZE RESIDUE WITH APPROPRIATE NEUTRALIZER. DO NOT ATTEMPT TO
NEUTRALIZE LARGE QUANTITIES OF MATERIAL UNLESS MEASURES TO CONTROL
REACTIVITY AND HEAT GENERATION HAVE BEEN TAKEN. AFTER REMOVAL, FLUSH SPILL
AREA WITH SOAP AND WATER TO REMOVE TRACE RESIDUE.
AVOID PERSONAL CONTACT AND BREATHING VAPORS OR MISTS. VENTILATE AREA. USE
PROPER PERSONAL PROTECTIVE EQUIPMENT AS LISTED IN SECTION 8.
A BLANKET OF PROTEIN FOAM MAY BE PLACED OVER SPILL FOR TEMPORARY CONTROL
OF ISOCYANATE VAPOR.
REFERENCE TO OTHER SECTIONS:
OTHER PRECAUTIONS:
PUMP LARGE QUANTITIES INTO CLOSED BUT NOT SEALED METAL CONTAINERS.
ISOCYANATES WILL REACT WITH WATER AND GENERATE CARBON DIOXIDE, THIS COULD
RESULT IN THE RUPTURE OF ANY CLOSED CONTAINERS.
NEUTRALIZE USING 10 PARTS NEUTRALIZER TO 1 PART ISOCYANATE SOLUTION. MIX
AND ALLOW TO STAND FOR 48 HRS IN CONTAINERS, LETTING EVOLVED CARBON DIOXIDE
TO VENT. NEUTRALIZER CONSIST OF 90% WATER, 3-8% CONCENTRATED AMMONIA
(OR SODIUM CARBONATE), 2% DETERGENT.
| SECTION 7: HANDLING AND STORAGE | |
PRECAUTIONS FOR SAFE HANDLING:
HANDLING:
USE WITH ADEQUATE VENTILATION. AVOID BREATHING VAPOR, AEROSOL OR MIST.
HYGIENE PRACTICES: WASH THOROUGHLY AFTER HANDLING.
SPECIAL HANDLING PROCEDURES:
PROVIDE APPROPRIATE VENTILATION/RESPIRATORY PROTECTION AGAINST
DECOMPOSITION PRODUCTS (SEE SECTION 10) DURING WELDING/FLAME CUTTING
OPERATIONS AND TO PROTECT AGAINST DUST DURING SANDING/GRINDING OF CURED
PRODUCT.
CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPATIBILITIES:
STORAGE:
STORE INDOORS IN A DRY PLACE AWAY FROM HEAT BETWEEN 64 TO 86 DEG. F STORE
IN A COOL, DRY, WELL VENTILATED AREA AWAY FROM SOURCES OF HEAT AND
INCOMPATIBLE MATERIALS. KEEP CONTAINER TIGHTLY CLOSED WHEN NOT IN USE. DO
NOT RESEAL CONTAINER IF MOISTURE OR WATER CONTAMINATION IS SUSPECTED. WATER
CONTAMINATED MATERIAL IN A SEALED CONTAINER MAY RUPTURE DUE TO PRESSURE
BUILDUP.
| SECTION 8: EXPOSURE CONTROLS, PERSONAL PROTECTION | |
EXPOSURE GUIDELINES:
4,4'-DIPHENYLMETHANE DIISOCYANATE:
GUIDELINE ACGIH:
TLV-TWA: 0.005 PPM
GUIDELINE OSHA:
PEL-CEILING/PEAK: 0.02 PPM
APPROPRIATE ENGINEERING CONTROLS:
ENGINEERING CONTROLS:
USE APPROPRIATE ENGINEERING CONTROL SUCH AS PROCESS ENCLOSURES, LOCAL
EXHAUST VENTILATION, OR OTHER ENGINEERING CONTROLS TO CONTROL AIRBORNE
LEVELS BELOW RECOMMENDED EXPOSURE LIMITS. GOOD GENERAL VENTILATION SHOULD
BE SUFFICIENT TO CONTROL AIRBORNE LEVELS. WHERE SUCH SYSTEMS ARE NOT
EFFECTIVE WEAR SUITABLE PERSONAL PROTECTIVE EQUIPMENT, WHICH PERFORMS
SATISFACTORILY AND MEETS OSHA OR OTHER RECOGNIZED STANDARDS. CONSULT WITH
LOCAL PROCEDURES FOR SELECTION, TRAINING, INSPECTION AND MAINTENANCE OF
THE PERSONAL PROTECTIVE EQUIPMENT.
INDIVIDUAL PROTECTION MEASURES:
EYE/FACE PROTECTION:
WEAR APPROPRIATE PROTECTIVE GLASSES OR SPLASH GOGGLES AS DESCRIBED BY
29 CFR 1910.133, OSHA EYE AND FACE PROTECTION REGULATION, OR THE EUROPEAN
STANDARD EN 166.
SKIN PROTECTION DESCRIPTION:
WEAR APPROPRIATE PROTECTIVE GLOVES AND OTHER PROTECTIVE APPAREL TO PREVENT
SKIN CONTACT. CONSULT MANUFACTURER'S DATA FOR PERMEABILITY DATA.
HAND PROTECTION DESCRIPTION:
USE PERMEATION RESISTANT GLOVES SUCH AS BUTYL RUBBER, NITRILE RUBBER OR
POLYVINYL ALCOHOL. HOWEVER, PLEASE NOTE THAT PVA DEGRADES WITH WATER.
RESPIRATORY PROTECTION:
A NIOSH APPROVED AIR-PURIFYING RESPIRATOR WITH AN ORGANIC VAPOR CARTRIDGE
OR CANISTER MAY BE PERMISSIBLE UNDER CERTAIN CIRCUMSTANCES WHERE AIRBORNE
CONCENTRATIONS ARE EXPECTED TO EXCEED EXPOSURE LIMITS. PROTECTION PROVIDED
BY AIR PURIFYING RESPIRATORS IS LIMITED. USE A POSITIVE PRESSURE AIR
SUPPLIED RESPIRATOR IF THERE IS ANY POTENTIAL FOR AN UNCONTROLLED RELEASE,
EXPOSURE LEVELS ARE NOT KNOWN, OR ANY OTHER CIRCUMSTANCES WHERE AIR
PURIFYING RESPIRATORS MAY NOT PROVIDE ADEQUATE PROTECTION.
OTHER PROTECTIVE:
FACILITIES STORING OR UTILIZING THIS MATERIAL SHOULD BE EQUIPPED WITH AN
EYEWASH AND A DELUGE SHOWER SAFETY STATION.
NOTES: ONLY ESTABLISHED PEL AND TLV VALUES FOR THE INGREDIENTS ARE LISTED.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
PHYSICAL AND CHEMICAL PROPERTIES:
PHYSICAL STATE APPEARANCE: LIQUID..
COLOR: PALE TO DARK YELLOW..
ODOR: SLIGHTLY MUSTY.
BOILING POINT: NOT DETERMINED.
MELTING POINT: 60-68 DEG. F (15.5-20 DEG. C)
SPECIFIC GRAVITY: 1.41 @ 77 DEG. F
SOLUBILITY: INSOLUBLE.
VAPOR DENSITY: 8.5 MDI (AIR = 1)
VAPOR PRESSURE: <10 MMHg @ 77 DEG. F (MDI)
PERCENT VOLATILE: NEGLIGIBLE
EVAPORATION RATE: NOT DETERMINED.
PH: NOT DETERMINED.
MOLECULAR FORMULA: MIXTURE
MOLECULAR WEIGHT: MIXTURE
FLASH POINT: >450 DEG. F (>232 DEG. C)
FLASH POINT METHOD: PENSKY-MARTEN CLOSED CUP (PMCC)
LOWER FLAMMABLE/EXPLOSIVE LIMIT: NOT DETERMINED.
UPPER FLAMMABLE/EXPLOSIVE LIMIT: NOT DETERMINED.
AUTO IGNITION TEMPERATURE: NOT DETERMINED.
VOC CONTENT: NOT DETERMINED.
9.2. OTHER INFORMATION:
PERCENT SOLIDS BY WEIGHT:
| SECTION 10: STABILITY AND REACTIVITY | |
CHEMICAL STABILITY:
CHEMICAL STABILITY:
STABLE UNDER NORMAL TEMPERATURES AND PRESSURES. PRODUCT IS VERY UNSTABLE
WHEN CONTAMINATED WITH WATER.
POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION:
CAN OCCUR. POLYMERIZATION AN BE CATALYZED BY STRONG BASES AND WATER
CONDITIONS TO AVOID:
CONDITIONS TO AVOID:
AVOID TEMPERATURES ABOVE 86 DEG. F. AVOID TEMPERATURES BELOW 64 DEG. F.
AVOID MOISTURE. PRODUCT CAN DECOMPOSE AT ELEVATED TEMPERATURE
INCOMPATIBLE MATERIALS:
INCOMPATIBLE MATERIALS:
AVOID CONTACT WITH METALS SUCH AS ALUMINUM, BRASS, COPPER, GALVANIZED
METALS, ZINC REACTION WITH WATER CAN GENERATE CARBON DIOXIDE. AVOID CONTACT
WITH ACIDS, ALCOHOL, AMINES, AMMONIA, BASES, METAL COMPOUNDS, MOIST AIR,
STRONG OXIDIZERS, WATER. AVOID UNINTENDED CONTACT WITH POLYOLS.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
TOXICOLOGICAL INFORMATION:
4,4'-DIPHENYLMETHANE DIISOCYANATE:
EYE:
ADMINISTRATION INTO THE EYE - RABBIT STANDARD DRAIZE TEST:
100 MG [MODERATE] (RTECS)
INHALATION:
INHALATION - RAT LC50 - LETHAL CONCENTRATION, 50 PERCENT KILL:
178 MG/M3 [DETAILS OF TOXIC EFFECTS NOT REPORTED OTHER THAN LETHAL DOSE
VALUE] (RTECS)
INGESTION:
ORAL - RAT LD50 - LETHAL DOSE, 50 PERCENT KILL:
9200 MG/KG [BEHAVIORAL - SOMNOLENCE (GENERAL DEPRESSED ACTIVITY)
BEHAVIORAL - ATAXIA NUTRITIONAL AND GROSS METABOLIC - BODY TEMPERATURE
DECREASE] (RTECS)
CHRONIC EFFECTS:
LUNG TUMORS HAVE BEEN OBSERVED IN LABORATORY ANIMALS EXPOSED TO AEROSOL
DROPLETS OF MDI/POLYMERIC MDI (6 MG/M3 ) FOR THEIR LIFETIME. TUMORS
OCCURRED CONCURRENTLY WITH RESPIRATORY IRRITATION AND LUNG INJURY. CURRENT
EXPOSURE GUIDELINES ARE EXPECTED TO PROTECT AGAINST THESE EFFECTS REPORTED
FOR MDI
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICITY:
ECOTOXICITY: NO ECOTOXICITY DATA WAS FOUND FOR THE PRODUCT.
ENVIRONMENTAL FATE: NO ENVIRONMENTAL INFORMATION FOUND FOR THIS PRODUCT.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
DESCRIPTION OF WASTE:
WASTE DISPOSAL:
CONSULT WITH THE US EPA GUIDELINES LISTED IN 40 CFR PART 261.3 FOR THE
CLASSIFICATIONS OF HAZARDOUS WASTE PRIOR TO DISPOSAL. FURTHERMORE, CONSULT
WITH YOUR STATE AND LOCAL WASTE REQUIREMENTS OR GUIDELINES, IF APPLICABLE,
TO ENSURE COMPLIANCE. ARRANGE DISPOSAL IN ACCORDANCE TO THE EPA AND/OR
STATE AND LOCAL GUIDELINES.
RCRA NUMBER: NOT DETERMINED.
| SECTION 14: TRANSPORT INFORMATION | |
DOT SHIPPING NAME: REFER TO BILL OF LADING
DOT UN NUMBER: REFER TO BILL OF LADING
IATA SHIPPING NAME: REFER TO BILL OF LADING
IATA UN NUMBER: REFER TO BILL OF LADING
IMDG UN NUMBER: REFER TO BILL OF LADING
IMDG SHIPPING NAME: REFER TO BILL OF LADING
| SECTION 15: REGULATORY INFORMATION | |
SAFETY, HEALTH AND ENVIRONMENTAL REGULATIONS SPECIFIC FOR THE PRODUCT:
4,4'-DIPHENYLMETHANE DIISOCYANATE:
TSCA INVENTORY STATUS: LISTED
SECTION 313:
EPCRA - 40 CFR PART 372 - (SARA TITLE III) SECTION 313 LISTED CHEMICAL.
CANADA DSL: LISTED
DIPHENYLMETHANE DIISOCYANATE:
TSCA INVENTORY STATUS: LISTED
CANADA DSL: LISTED
CANADIAN REGULATIONS.:
WHMIS HAZARD CLASS(ES): D2A
ALL COMPONENTS OF THIS PRODUCT ARE ON THE CANADIAN DOMESTIC SUBSTANCES
LIST.
WHMIS PICTOGRAMS: D2 - MATERIALS CAUSING OTHER TOXIC EFFECTS
| SECTION 16: ADDITIONAL INFORMATION | |
HMIS RATINGS:
HMIS HEALTH HAZARD 3*
HMIS FIRE HAZARD 1
HMIS REACTIVITY 1
HMIS PERSONAL PROTECTION X
HEALTH HAZARD 3*
FIRE HAZARD 1
REACTIVITY 1
PERSONAL PROTECTION X
* CHRONIC HEALTH EFFECTS
SDS REVISION DATE: JULY 25, 2015
SDS REVISION NOTES: GHS UPDATE
SDS FORMAT: IN ACCORDANCE TO OSHA GHS 1910.1200
SDS AUTHOR: ACTIO CORPORATION
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. ITW POLYMERS ADHESIVES, NA, MAKES NO WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF
PERFORMANCE OR USAGE OF TRADE. USER IS RESPONSIBLE FOR DETERMINING
WHETHER THE ITW POLYMERS ADHESIVES, NA PRODUCT IS FIT FOR A PARTICULAR
PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR APPLICATION. GIVEN THE
VARIETY OF FACTORS THAT CAN AFFECT THE USE AND APPLICATION OF A ITW
POLYMERS ADHESIVES, NA PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE
USER'S KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE
ITW POLYMERS ADHESIVES, NA PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A
PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
ITW POLYMERS ADHESIVES, NA PROVIDES INFORMATION IN ELECTRONIC FORM AS A
SERVICE TO ITS CUSTOMERS. DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC
TRANSFER MAY HAVE RESULTED IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS
INFORMATION, ITW POLYMERS ADHESIVES, NA MAKES NO REPRESENTATIONS AS TO
ITS COMPLETENESS OR ACCURACY. IN ADDITION, INFORMATION OBTAINED FROM A
DATABASE MAY NOT BE AS CURRENT AS THE INFORMATION IN THE MSDS AVAILABLE
DIRECTLY FROM ITW POLYMERS ADHESIVES, NA
COPYRIGHT(C) 1996-2018 ENVIANCE. ALL RIGHTS RESERVED.
PRODUCT: DEVCON(R*) DEV-THANE 5(TM) GREY [1:1]
MANUFACTURER:
REVISON: 9/10/2015
VERSION: 0