| Common Name: | ALL-STATE DYNAGRIP NO. 430 |
| Manufacturer: | ESAB |
| SDS Revision Date: | 9/27/2016 |
| SDS Format: | GHS-US |
| Item Number(s): | 400G89, 400G90, 400G91, 400G92 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
ESAB(R*)
SAFETY DATA SHEET
ALL-STATE DYNAGRIP NO. 430
REPLACES SDS: 2016-05-25
ISSUED: 2016-09-27
| SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE |  |
AND OF THE COMPANY/UNDERTAKING
1.1. PRODUCT IDENTIFIER:
TRADE NAME: ALL-STATE DYNAGRIP NO. 430
1.2. RELEVANT IDENTIFIED USES OF THE SUBSTANCE OR MIXTURE AND USES ADVISED
AGAINST:
USE: WIRE USED FOR SOLDERING COPPER AND COPPER BASED ALLOYS
1.3. DETAILS OF THE SUPPLIER OF THE SAFETY DATA SHEET:
SUPPLIER: ESAB WELDING & CUTTING PRODUCTS
STREET ADDRESS:
801 WILSON AVE.
HANOVER, PA 17331
TELEPHONE: 1-717-637-8911
FAX: 1-717-630-3458
EMAIL: US.TECHNICAL.FILLERMETALS@ESAB.COM
WEB SITE: WWW.ESABNA.COM
1.4. EMERGENCY TELEPHONE NUMBER:
EMERGENCY PHONE NUMBER: 1-800-424-9300 (CHEMTREC)
AVAILABLE OUTSIDE OFFICE HOURS: YES
OTHER:
AWS CLASSIFICATION: NONE
| SECTION 2: HAZARDS IDENTIFICATION | |
2.1. CLASSIFICATION OF THE SUBSTANCE OR MIXTURE:
DESCRIPTION:
THIS PRODUCT IS NOT CLASSIFIED AS HAZARDOUS ACCORDING TO APPLICABLE GHS
HAZARD CLASSIFICATION CRITERIA AS REQUIRED AND DEFINED IN OSHA HAZARD
COMMUNICATION STANDARD (29CFR PART 1910.1200).
2.2. LABEL ELEMENTS:
MORE INFORMATION: THIS PRODUCT DOES NOT REQUIRE LABELING.
2.3. OTHER HAZARDS:
PERSONS WITH A PACEMAKER SHOULD NOT GO NEAR WELDING OR CUTTING OPERATIONS
UNTIL THEY HAVE CONSULTED THEIR DOCTOR AND OBTAINED INFORMATION FROM THE
MANUFACTURER OF THE DEVICE.
WHEN THIS PRODUCT IS USED IN A SOLDERING PROCESS, THE MOST IMPORTANT
HAZARDS ARE HEAT, RADIATION, ELECTRIC SHOCK AND SOLDERING FUMES.
FUMES:
OVEREXPOSURE TO SOLDERING FUMES MAY RESULT IN SYMPTOMS LIKE METAL FUME
FEVER, DIZZINESS, NAUSEA, DRYNESS OR IRRITATION OF THE NOSE, THROAT OR
EYES. CHRONIC OVEREXPOSURE TO SOLDERING FUMES MAY AFFECT PULMONARY
FUNCTION. PROLONGED INHALATION OF NICKEL AND CHROMIUM COMPOUNDS ABOVE
SAFE EXPOSURE LIMITS CAN CAUSE CANCER. OVEREXPOSURE TO MANGANESE AND
MANGANESE COMPOUNDS ABOVE SAFE EXPOSURE LIMITS CAN CAUSE IRREVERSIBLE
DAMAGE TO THE CENTRAL NERVOUS SYSTEM, INCLUDING THE BRAIN, SYMPTOMS OF
WHICH MAY INCLUDE SLURRED SPEECH, LETHARGY, TREMOR, MUSCULAR WEAKNESS,
PSYCHOLOGICAL DISTURBANCES AND SPASTIC GAIT. SOME INDIVIDUALS MAY DEVELOP
A BLUE-GREY SKIN PIGMENTATION FROM EXPOSURE TO SILVER (ARGYRIA).
HEAT: SPATTER AND MELTING METAL CAN CAUSE BURN INJURIES AND START FIRES.
RADIATION: ARC RAYS CAN SEVERELY DAMAGE EYES OR SKIN.
ELECTRICITY: ELECTRIC SHOCK CAN KILL.
FLAME PROCESSING:
WHEN USED WITH COMBUSTIBLE GAS EQUIPMENT (E.G., OXY-ACETYLENE TORCH),
READ THE USE AND SAFETY INFORMATION FOR THAT EQUIPMENT.
OTHER:
SILVER-WHITE METAL WIRE. THIS PRODUCT IS NORMALLY NOT CONSIDERED HAZARDOUS
AS SHIPPED. GLOVES SHOULD BE WORN WHEN HANDLING TO PREVENT CUTS AND
ABRASIONS.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
3.2. MIXTURES:
CHEMICAL NAME CAS NO. CONCENTRATION CLASSIFICATION R-PHRASE
EC NO. H-PHRASE
TIN 7440-31-5 94 - 99%
231-141-8
SILVER 7440-22-4 1 - 6%
213-131-3
PRODUCT BASED ON: THIS PRODUCT IS A SOLID METAL WIRE.
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
ELECTRIC SHOCK:
DISCONNECT AND TURN OFF THE POWER. USE A NONCONDUCTIVE MATERIAL TO PULL
VICTIM AWAY FROM CONTACT WITH LIVE PARTS OR WIRES. IF NOT BREATHING, BEGIN
ARTIFICIAL RESPIRATION, PREFERABLY MOUTH-TO-MOUTH. IF NO DETECTABLE PULSE,
BEGIN CARDIO PULMONARY RESUSCITATION (CPR). CALL A PHYSICIAN IMMEDIATELY.
INHALATION:
IF BREATHING HAS STOPPED, PERFORM ARTIFICIAL RESPIRATION AND OBTAIN
MEDICAL ASSISTANCE IMMEDIATELY! IF BREATHING IS DIFFICULT, PROVIDE
FRESH AIR AND CALL PHYSICIAN. OBTAIN MEDICAL ASSISTANCE FOR IRRITATION
OR ANY OTHER SYMPTOM.
SKIN CONTACT:
FOR SKIN BURNS FROM ARC RADIATION, PROMPTLY FLUSH WITH COLD WATER. GET
MEDICAL ATTENTION FOR BURNS OR IRRITATIONS THAT PERSIST. TO REMOVE DUST
OR PARTICLES WASH WITH MILD SOAP AND WATER.
EYE CONTACT:
FOR RADIATION BURNS DUE TO ARC FLASH, SEE PHYSICIAN. TO REMOVE DUSTS
OR FUMES FLUSH WITH WATER FOR AT LEAST FIFTEEN MINUTES. IF IRRITATION
PERSISTS, OBTAIN MEDICAL ASSISTANCE.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
NOT APPLICABLE
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
NEEDED:
NOT APPLICABLE
| SECTION 5: FIREFIGHTING MEASURES | |
5.1. EXTINGUISHING MEDIA:
SUITABLE EXTINGUISHING MEDIA:
NO SPECIFIC RECOMMENDATIONS FOR SOLDERING CONSUMABLES.THE SOLDERING
PROCESS CAN IGNITE COMBUSTIBLE AND FLAMMABLE MATERIALS. USE THE
EXTINGUISHING MEDIA RECOMMENDED FOR THE BURNING MATERIALS AND FIRE
SITUATION.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE: NOT APPLICABLE
5.3. ADVICE FOR FIREFIGHTERS:
SPECIAL PROTECTIVE EQUIPMENT FOR FIRE-FIGHTERS:
WEAR SELF-CONTAINED BREATHING APPARATUS AS FUMES OR VAPORS MAY BE HARMFUL.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
REFER TO SECTION 8.
6.2. ENVIRONMENTAL PRECAUTIONS: REFER TO SECTION 13.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP:
SOLID OBJECTS MAY BE PICKED UP AND PLACED INTO A CONTAINER. LIQUIDS OR
PASTES SHOULD BE SCOOPED UP AND PLACED INTO A CONTAINER. WEAR PROPER
PROTECTIVE EQUIPMENT WHILE HANDLING THESE MATERIALS. DO NOT DISCARD AS
REFUSE.
6.4. REFERENCE TO OTHER SECTIONS: REFER TO SECTION 8 AND SECTION 13.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
PREVENTIVE HANDLING PRECAUTIONS:
HANDLE WITH CARE TO AVOID STINGS AND CUTS. WEAR GLOVES WHEN HANDLING
SOLDERING CONSUMABLES. AVOID EXPOSURE TO DUST. DO NOT INGEST. DO NOT
BREATHE VAPORS PRODUCED BY USE OF THIS PRODUCT.SOME INDIVIDUALS CAN
DEVELOP AN ALLERGIC REACTION TO CERTAIN MATERIALS. RETAIN ALL WARNING
AND IDENTITY LABELS.
7.2. CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPATIBILITIES:
KEEP SEPARATE FROM CHEMICAL SUBSTANCES LIKE ACIDS AND STRONG BASES,
WHICH COULD CAUSE CHEMICAL REACTIONS.
7.3. SPECIFIC END USE(S): SOLDERING
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
EXPOSURE LIMITS:
USE INDUSTRIAL HYGIENE MONITORING EQUIPMENT TO ENSURE THAT EXPOSURE DOES
NOT EXCEED APPLICABLE NATIONAL EXPOSURE LIMITS. THE FOLLOWING LIMITS CAN
BE USED AS GUIDANCE. UNLESS NOTED, ALL VALUES ARE FOR 8 HOUR TIME WEIGHTED
AVERAGES (TWA). FOR INFORMATION ABOUT WELDING FUME ANALYSIS, REFER TO
SECTION 10.
ACGIH TLV, MG/M3:
SILVER (METAL): 0.1 (DUST AND FUME)
TIN (METAL): 2
USA, OSHA PEL, MG/M3:
NATIONAL OCCUPATIONAL EXPOSURE LIMITS:
INGREDIENT CAS NO. EC NO. EXPOSURE LIMIT MG/M3-PPM
TIN 7440-31-5 2
SILVER 7440-22-4 0,01
INGREDIENT SHORT-TERM EXPOSURE LIMIT MG/M3-PPM REMARK SOURCE YEAR
TIN METAL 2016
SILVER METAL 2016
8.2. EXPOSURE CONTROLS: NOT APPLICABLE
OTHER:
AVOID EXPOSURE TO SOLDERING FUMES, RADIATION, SPATTER, ELECTRIC SHOCK,
HEATED MATERIALS AND DUST. TRAIN WELDERS TO AVOID CONTACT WITH LIVE
ELECTRICAL PARTS AND INSULATE CONDUCTIVE PARTS.
VENTILATION:
USE RESPIRATOR OR AIR SUPPLIED RESPIRATOR WHEN SOLDERING IN A CONFINED
SPACE, OR WHERE LOCAL VENTILATION IS NOT SUFFICIENT TO KEEP EXPOSURE
VALUES WITHIN SAFE LIMITS. USE SPECIAL CARE WHEN SOLDERING PAINTED OR
COATED STEELS SINCE HAZARDOUS SUBSTANCES FROM THE COATING MAY BE EMITTED.
ENSURE SUFFICIENT VENTILLATION, LOCAL EXHAUST, OR BOTH, TO KEEP SOLDERING
FUMES AND GASES FROM THE BREATHING ZONE AND GENERAL AREA.
PERSONAL PROTECTIVE EQUIPMENT:
WEAR HAND, HEAD, EYES, EAR AND BODY PROTECTION LIKE WELDERS GLOVES, HELMET
OR FACE SHIELD WITH FILTER LENS, SAFETY BOOTS, APRON, ARM AND SHOULDER
PROTECTION. KEEP PROTECTIVE CLOTHING CLEAN AND DRY.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
APPEARANCE: WIRE
APPEARANCE, COLOUR: SILVER GREY
APPEARANCE, PHYSICAL STATE: SOLID
AUTO-IGNITION TEMPERATURE: PRODUCT IS NOT SELF IGNITING.
DECOMPOSITION TEMPERATURE: NO DATA AVAILABLE
EVAPORATION RATE: NOT APPLICABLE
EXPLOSIVE PROPERTIES: PRODUCT DOES NOT PRESENT AN EXPLOSION HAZARD.
FLAMMABILITY (SOLID, GAS): NOT APPLICABLE
FLASH POINT: NOT APPLICABLE
INITIAL BOILING POINT AND BOILING RANGE: NO DATA AVAILABLE
MELTING POINT: 217 DEG. C/ 423 DEG. F
MELTING POINT / FREEZING POINT: NOT APPLICABLE
ODOUR: NOT APPLICABLE
ODOUR TRESHOLD: NOT APPLICABLE
OXIDISING PROPERTIES: NOT APPLICABLE
PARTITION COEFFICIENT N-OCTANOL / WATER: NOT APPLICABLE
PH: VALUE NOT APPLICABLE
RELATIVE DENSITY: 7.1 G/CM3
SOLUBILITY: NO DATA AVAILABLE
UPPER / LOWER FLAMMABILITY OR EXPLOSIVE LIMITS: NOT APPLICABLE
VAPOUR DENSITY: NOT APPLICABLE
VAPOUR PRESSURE: NOT APPLICABLE
VISCOSITY: NOT APPLICABLE
VOLATILITY: NOT APPLICABLE
9.2. OTHER INFORMATION: NOT APPLICABLE
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
REACTIVITY:
CONTACT WITH CHEMICAL SUBSTANCES LIKE ACIDS OR STRONG BASES COULD CAUSE
GENERATION OF GAS.
10.2. CHEMICAL STABILITY:
CHEMICAL STABILITY: THIS PRODUCT IS STABLE UNDER NORMAL CONDITIONS.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
POSSIBILITY OF HAZARDOUS REACTIONS: NOT APPLICABLE
10.4. CONDITIONS TO AVOID:
CONDITIONS TO AVOID:
THIS PRODUCT IS ONLY INTENDED FOR NORMAL SOLDERING PURPOSES.
10.5. INCOMPATIBLE MATERIALS:
INCOMPATIBLE MATERIALS: NOT APPLICABLE
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
HAZARDOUS DECOMPOSITION PRODUCTS:
WHEN THIS PRODUCT IS USED IN A SOLDERING PROCESS, HAZARDOUS
DECOMPOSITION PRODUCTS WOULD INCLUDE THOSE FROM THE VOLATILIZATION,
REACTION, OR OXIDATION OF THE MATERIALS LISTED IN SECTION 3, AND THOSE
FROM THE BASE METAL AND COATING.
FUMES FROM THIS PRODUCT MAY CONTAIN COMPOUNDS OF THE FOLLOWING CHEMICAL
ELEMENTS:
Ag, Sn, AND NITROGEN OXIDE. THE REST IS NOT ANALYZED, ACCORDING TO
AVAILABLE STANDARDS.
OTHER:
REFER TO APPLICABLE NATIONAL EXPOSURE LIMITS FOR FUME COMPOUNDS, INCLUDING
THOSE EXPOSURE LIMITS FOR FUME COMPOUNDS FOUND IN SECTION 8.
A SIGNIFICANT AMOUNT OF THE CHROMIUM IN THE FUMES CAN BE HEXAVALENT
CHROMIUM, WHICH HAS A VERY LOW EXPOSURE LIMIT IN SOME COUNTRIES.
MANGANESE AND NICKEL HAVE LOW EXPOSURE LIMITS, IN SOME COUNTRIES, THAT MAY
BE EASILY EXCEEDED.
REASONABLY EXPECTED GASEOUS PRODUCTS WOULD INCLUDE CARBON OXIDES, NITROGEN
OXIDES AND OZONE. AIR CONTAMINANTS AROUND THE SOLDERING AREA CAN BE
AFFECTED BY THE SOLDERING PROCESS AND INFLUENCE THE COMPOSITION AND
QUANTITY OF FUMES AND GASES PRODUCED.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
INFORMATION ON TOXICOLOGICAL EFFECTS:
INHALATION OF SOLDERING FUMES CAN BE DANGEROUS TO YOUR HEALTH.
CLASSIFICATION OF SOLDERING FUMES IS DIFFICULT BECAUSE OF VARYING BASE
MATERIALS, COATINGS, AIR CONTAMINATION AND PROCESSES.
THE INTERNATIONAL AGENCY FOR RESEARCH ON CANCER HAS CLASSIFIED WELDING
FUMES AS POSSIBLY CARCINOGENIC TO HUMANS (GROUP 2B).
ACUTE TOXICITY:
OVEREXPOSURE TO SOLDERING FUMES MAY RESULT IN SYMPTOMS LIKE METAL FUME
FEVER, DIZZINESS, NAUSEA, DRYNESS OR IRRITATION OF THE NOSE, THROAT OR
EYES.
SKIN CORROSION/IRRITATION: NOT APPLICABLE
SERIOUS EYE DAMAGE/IRRITATION: NOT APPLICABLE
IRRITATION: NOT APPLICABLE
CORROSIVE EFFECTS: NOT APPLICABLE
RESPIRATORY OR SKIN SENSITISATION: NOT APPLICABLE
GERM CELL MUTAGENICITY: NOT APPLICABLE
MUTAGENICITY: NOT APPLICABLE
CARCINOGENICITY: NOT APPLICABLE
REPEATED DOSE TOXICITY: NOT APPLICABLE
REPRODUCTIVE TOXICITY: NOT APPLICABLE
STOT-SINGLE EXPOSURE: NOT APPLICABLE
STOT-REPEATED EXPOSURE: NOT APPLICABLE
ASPIRATION HAZARD: NOT APPLICABLE
OTHER:
LONG TERM EFFECT:
CHRONIC TOXICITY:
CHRONIC OVEREXPOSURE TO SOLDERING FUMES MAY AFFECT PULMONARY FUNCTION.
PROLONGED INHALATION OF NICKEL AND CHROMIUM COMPOUNDS ABOVE SAFE EXPOSURE
LIMITS CAN CAUSE CANCER. OVEREXPOSURE TO MANGANESE AND MANGANESE COMPOUNDS
ABOVE SAFE EXPOSURE LIMITS CAN CAUSE IRREVERSIBLE DAMAGE TO THE CENTRAL
NERVOUS SYSTEM, INCLUDING THE BRAIN, SYMPTOMS OF WHICH MAY INCLUDE SLURRED
SPEECH, LETHARGY, TREMOR, MUSCULAR WEAKNESS, PSYCHOLOGICAL DISTURBANCES
AND SPASTIC GAIT. SOME INDIVIDUALS MAY DEVELOP A BLUE-GREY SKIN
PIGMENTATION FROM EXPOSURE TO SILVER (ARGYRIA).
| SECTION 12: ECOLOGICAL INFORMATION | |
12.1. TOXICITY: NOT APPLICABLE
12.2. PERSISTENCE AND DEGRADABILITY: NOT APPLICABLE
12.3. BIOACCUMULATIVE POTENTIAL: NOT APPLICABLE
12.4. MOBILITY IN SOIL: NOT APPLICABLE
12.5. RESULTS OF PBT AND VPVB ASSESSMENT: NOT APPLICABLE
12.6. OTHER ADVERSE EFFECTS: NOT APPLICABLE
OTHER:
SOLDERING CONSUMABLES AND MATERIALS COULD DEGRADE/WEATHER INTO COMPONENTS
ORIGINATING FROM THE CONSUMABLES OR FROM THE MATERIALS USED IN THE
SOLDERING PROCESS. AVOID EXPOSURE TO CONDITIONS THAT COULD LEAD TO
ACCUMULATION IN SOILS OR GROUNDWATER.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. WASTE TREATMENT METHODS:
DISPOSAL CONSIDERATIONS:
DISCARD ANY PRODUCT, RESIDUE, DISPOSABLE CONTAINER OR LINER IN AN
ENVIRONMENTALLY ACCEPTABLE MANNER, IN FULL COMPLIANCE WITH FEDERAL
AND LOCAL REGULATIONS. USE RECYCLING PROCEDURES IF AVAILABLE.
USA RCRA:
UNUSED PRODUCT OR PRODUCT RESIDUE CONTAINING SILVER IS CONSIDERED
HAZARDOUS WASTE IF DISCARDED, RCRA ID CHARACTERISTIC TOXIC HAZARDOUS
WASTE D011.
RESIDUES FROM SOLDERING CONSUMABLES AND PROCESSES COULD DEGRADE AND
ACCUMULATE IN SOILS AND GROUNDWATER.
| SECTION 14: TRANSPORT INFORMATION | |
14.1. UN NUMBER: NOT APPLICABLE
14.2. UN PROPER SHIPPING NAME: NOT APPLICABLE
14.3. TRANSPORT HAZARD CLASS(ES): NOT APPLICABLE
14.4. PACKING GROUP: NOT APPLICABLE
14.5. ENVIRONMENTAL HAZARDS: NOT APPLICABLE
14.6. SPECIAL PRECAUTIONS FOR USER: NOT APPLICABLE
14.7. TRANSPORT IN BULK ACCORDING TO ANNEX II OF MARPOL AND THE IBC CODE:
NOT APPLICABLE
| SECTION 15: REGULATORY INFORMATION | |
15.1 SAFETY, HEALTH AND ENVIRONMENTAL REGULATIONS/LEGISLATION SPECIFIC FOR
THE SUBSTANCE OR MIXTURE:
15.1. SAFETY, HEALTH AND ENVIRONMENTAL REGULATIONS/LEGISLATION SPECIFIC
FOR THE SUBSTANCE OR MIXTURE:
CANADA:
WHMIS CLASSIFICATION: CLASS D; DIVISION 2, SUBDIVISION A
CANADIAN ENVIRONMENTAL PROTECTION ACT (CEPA):
ALL CONSTITUENTS OF THIS PRODUCT ARE ON THE DOMESTIC SUBSTANCE LIST (DSL).
USA:
THIS PRODUCT CONTAINS OR PRODUCES A CHEMICAL KNOWN TO THE STATE OF
CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS (OR OTHER REPRODUCTIVE HARM).
(CALIFORNIA HEALTH & SAFETY CODE SUBSECTION 25249.5 ET. SEQ.)
UNITED STATES EPA TOXIC SUBSTANCE CONTROL ACT:
ALL CONSTITUENTS OF THIS PRODUCT ARE ON THE TSCA INVENTORY LIST OR ARE
EXCLUDED FROM LISTING.
CERCLA/SARA TITLE III REPORTABLE QUANTITIES (RQS) AND/OR THRESHOLD
PLANNING QUANTITIES (TPQS):
PRODUCT IS A SOLID SOLUTION IN THE FORM OF A SOLID ARTICLE.
SPILLS OR RELEASES RESULTING IN THE LOSS OF ANY INGREDIENT AT OR ABOVE ITS
RQ REQUIRE IMMEDIATE NOTIFICATION TO THE NATIONAL RESPONSE CENTER AND TO
YOUR LOCAL EMERGENCY PLANNING COMMITTEE.
SECTION 311 HAZARD CLASS:
AS SHIPPED: IMMEDIATE
IN USE: IMMEDIATE DELAYED
EPCRA/SARA TITLE III 313 TOXIC CHEMICALS:
THE FOLLOWING METALLIC COMPONENTS ARE LISTED AS SARA 313 "TOXIC CHEMICALS"
AND POTENTIAL SUBJECT TO ANNUAL SARA 313 REPORTING. SEE SECTION 3 FOR
WEIGHT PERCENT. SILVER 1.0% DE MINIMIS CONCENTRATION
15.2. CHEMICAL SAFETY ASSESSMENT:
CHEMICAL SAFETY ASSESSMENT: NO
OTHER:
READ AND UNDERSTAND THE MANUFACTURER'S INSTRUCTIONS, YOUR EMPLOYER'S
SAFETY PRACTICES AND THE HEALTH AND SAFETY INSTRUCTIONS ON THE LABEL.
OBSERVE ANY FEDERAL AND LOCAL REGULATIONS. TAKE PRECAUTIONS WHEN SOLDERING
AND PROTECT YOURSELF AND OTHERS.
WARNING:
SOLDERING FUMES AND GASES ARE HAZARDOUS TO YOUR HEALTH AND MAY DAMAGE
LUNGS AND OTHER ORGANS. USE ADEQUATE VENTILATION.
ELECTRIC SHOCK CAN KILL.
ARC RAYS AND SPARKS CAN INJURE EYES AND BURN SKIN.
WEAR CORRECT HAND, HEAD, EYE AND BODY PROTECTION.
| SECTION 16: OTHER INFORMATION | |
CHANGES TO PREVIOUS REVISION:
THIS SAFETY DATA SHEET HAS BEEN REVISED DUE TO MODIFICATIONS TO SECTIONS
1-16.
REFERENCES TO KEY LITERATURE AND DATA SOURCES:
REFER TO ESAB "WELDING AND CUTTING - RISKS AND MEASURES", F52-529
"PRECAUTIONS AND SAFE PRACTICES FOR ELECTRIC WELDING AND CUTTING" AND
F2035 "PRECAUTIONS AND SAFE PRACTICES FOR GAS WELDING, CUTTING AND
HEATING" AVAILABLE FROM ESAB, AND TO:
USA:
CONTACT ESAB AT WWW.ESABNA.COM OR 1-800 ESAB-123 IF YOU HAVE ANY QUESTIONS
ABOUT THIS SDS.
AMERICAN NATIONAL STANDARD Z49.1 "SAFETY IN WELDING AND CUTTING", ANSI/AWS
F1.5 "METHODS FOR SAMPLING AND ANALYZING GASES FROM WELDING AND ALLIED
PROCESSES", ANSI/AWS F1.1 "METHOD FOR SAMPLING AIRBORNE PARTICLES
GENERATED BY WELDING AND ALLIED PROCESSES", AWSF3.2M/F3.2 "VENTILATION
GUIDE FOR WELD FUME", AMERICAN WELDING SOCIETY, 550 NORTH LE JEUNE ROAD,
MIAMI, FLORIDA, 33135. SAFETY AND HEALTH FACT SHEETS AVAILABLE FROM AWS
AT WWW.AWS.ORG.
OSHA PUBLICATION 2206 (29 C.F.R. 1910), U.S. GOVERNMENT PRINTING OFFICE,
SUPERINTENDENT OF DOCUMENTS, P.O. BOX 371954, PITTSBURGH, PA 15250-7954
AMERICAN CONFERENCE OF GOVERNMENTAL HYGIENISTS (ACGIH), THRESHOLD LIMIT
VALUES AND BIOLOGICAL EXPOSURE INDICES, 6500 GLENWAY AVE., CINCINNATI,
OHIO 45211, USA.
NFPA 51B "STANDARD FOR FIRE PREVENTION DURING WELDING, CUTTING AND OTHER
HOT WORK" PUBLISHED BY THE NATIONAL FIRE PROTECTION ASSOCIATION, 1
BATTERYMARCH PARK, QUINCY, MA 02169
UK:
WMA PUBLICATION 236 AND 237, "HAZARDS FROM WELDING FUME", "THE ARC WELDER
AT WORK, SOME GENERAL ASPECTS OF HEALTH AND SAFETY".
GERMANY:
UNFALLVERHUTUNGSVORSCHRIFT BGV D1, "SCHWEIBEN, SCHNEIDEN UND VERWANDTE
VERFAHREN".
CANADA:
CSA STANDARD CAN/CSA-W117.2-01 "SAFETY IN WELDING, CUTTING AND ALLIED
PROCESSES"
THIS PRODUCT HAS BEEN CLASSIFIED ACCORDING TO THE HAZARD CRITERIA OF THE
CPR AND THE SDS CONTAINS ALL THE INFORMATION REQUIRED BY THE CPR.
OTHER:
ADDITIONAL INFORMATION:
ESAB REQUESTS THE USERS OF THIS PRODUCT TO STUDY THIS SAFETY DATA SHEET
(SDS) AND BECOME AWARE OF PRODUCT HAZARDS AND SAFETY INFORMATION. TO
PROMOTE SAFE USE OF THIS PRODUCT A USER SHOULD:
NOTIFY ITS EMPLOYEES, AGENTS AND CONTRACTORS OF THE INFORMATION ON THIS
SDS AND ANY PRODUCT HAZARDS/SAFETY INFORMATION.
FURNISH THIS SAME INFORMATION TO EACH OF ITS CUSTOMERS FOR THE PRODUCT.
REQUEST SUCH CUSTOMERS TO NOTIFY EMPLOYEES AND CUSTOMERS FOR THE SAME
PRODUCT HAZARDS AND SAFETY INFORMATION.
THE INFORMATION HEREIN IS GIVEN IN GOOD FAITH AND BASED ON TECHNICAL DATA
THAT ESAB BELIEVES TO BE RELIABLE. SINCE THE CONDITIONS OF USE IS OUTSIDE
OUR CONTROL, WE ASSUME NO LIABILITY IN CONNECTION WITH ANY USE OF THIS
INFORMATION AND NO WARRANTY, EXPRESSED OR IMPLIED IS GIVEN. CONTACT ESAB
FOR MORE INFORMATION.