| Common Name: | NON-ACID BATHROOM CLEANER CONCENTRATE (PRODUCT NO. 19, TWIST 'N FILL SYSTEM) |
| Manufacturer: | 3M |
| SDS Revision Date: | 8/22/2017 |
| SDS Format: | GHS-US |
| Item Number(s): | 4HN93 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M(TM) NON-ACID BATHROOM CLEANER CONCENTRATE (PRODUCT NO. 19, TWIST 'N
FILL(TM) SYSTEM)
08/22/17
3M
SAFETY DATA SHEET
COPYRIGHT,2017,3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR
THE PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR
WRITTEN AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 07-8343-1
ISSUE DATE: 08/22/17
VERSION NUMBER: 9.00
SUPERCEDES DATE: 06/27/16
| SECTION 1: IDENTIFICATION |  |
1.1. PRODUCT IDENTIFIER:
3M(TM) NON-ACID BATHROOM CLEANER CONCENTRATE (PRODUCT NO. 19, TWIST 'N
FILL(TM) SYSTEM)
PRODUCT IDENTIFICATION NUMBERS:
61-0000-6343-0, 70-0708-4019-7, 70-0716-8289-5
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE:
DAILY-USE BATHROOM CLEANER FOR TOILETS, URINALS AND OTHER HARD SURFACES.,
HARD SURFACE CLEANER
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: COMMERCIAL SOLUTIONS DIVISION
ADDRESS:
3M CENTER, ST. PAUL
MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
SERIOUS EYE DAMAGE/IRRITATION: CATEGORY 2A.
SKIN CORROSION/IRRITATION: CATEGORY 2.
SKIN SENSITIZER: CATEGORY 1.
2.2. LABEL ELEMENTS:
SIGNAL WORD: WARNING
SYMBOLS: EXCLAMATION MARK
PICTOGRAMS: EXCLAMATION MARK
HAZARD STATEMENTS:
CAUSES SERIOUS EYE IRRITATION.
CAUSES SKIN IRRITATION.
MAY CAUSE AN ALLERGIC SKIN REACTION.
PRECAUTIONARY STATEMENTS:
PREVENTION:
AVOID BREATHING DUST/FUME/GAS/MIST/VAPORS/SPRAY.
WEAR EYE/FACE PROTECTION.
WEAR PROTECTIVE GLOVES.
WASH THOROUGHLY AFTER HANDLING.
CONTAMINATED WORK CLOTHING MUST NOT BE ALLOWED OUT OF THE WORKPLACE.
RESPONSE:
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES, IF
PRESENT AND EASY TO DO. CONTINUE RINSING.
IF EYE IRRITATION PERSISTS: GET MEDICAL ADVICE/ATTENTION.
IF ON SKIN: WASH WITH PLENTY OF SOAP AND WATER.
IF SKIN IRRITATION OR RASH OCCURS: GET MEDICAL ADVICE/ATTENTION.
TAKE OFF CONTAMINATED CLOTHING AND WASH IT BEFORE REUSE.
DISPOSAL:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH APPLICABLE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
2.3. HAZARDS NOT OTHERWISE CLASSIFIED:
39% OF THE MIXTURE CONSISTS OF INGREDIENTS OF UNKNOWN ACUTE ORAL TOXICITY.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
WATER 7732-18-5 50 - 80 TRADE SECRET *
CARBOXYIMIDAZOLINIUM 13039-35-5 15 - 40 TRADE SECRET *
SALT
SODIUM CHLORIDE 7647-14-5 1 - 5 TRADE SECRET *
ASCORBIC ACID 50-81-7 0.1 - 1 TRADE SECRET *
FRAGRANCE
(NJTSN 04499600-6540) TRADE SECRET* 1 - 5 TRADE SECRET *
NJTS OR NJTSRN: NEW JERSEY TRADE SECRET REGISTRY NUMBER.
*THE SPECIFIC CHEMICAL IDENTITY AND/OR EXACT PERCENTAGE (CONCENTRATION)
OF THIS COMPOSITION HAS BEEN WITHHELD AS A TRADE SECRET.
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
IMMEDIATELY WASH WITH SOAP AND WATER. REMOVE CONTAMINATED CLOTHING AND WASH
BEFORE REUSE. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL ATTENTION.
EYE CONTACT:
IMMEDIATELY FLUSH WITH LARGE AMOUNTS OF WATER. REMOVE CONTACT LENSES IF
EASY TO DO. CONTINUE RINSING. GET MEDICAL ATTENTION.
IF SWALLOWED:
RINSE MOUTH. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED: NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA: MATERIAL WILL NOT BURN.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
CLOSED CONTAINERS EXPOSED TO HEAT FROM FIRE MAY BUILD PRESSURE AND EXPLODE.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
WATER MAY NOT EFFECTIVELY EXTINGUISH FIRE; HOWEVER, IT SHOULD BE USED
TO KEEP FIRE-EXPOSED CONTAINERS AND SURFACES COOL AND PREVENT EXPLOSIVE
RUPTURE.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
EVACUATE AREA. VENTILATE THE AREA WITH FRESH AIR. FOR LARGE SPILL, OR
SPILLS IN CONFINED SPACES, PROVIDE MECHANICAL VENTILATION TO DISPERSE OR
EXHAUST VAPORS, IN ACCORDANCE WITH GOOD INDUSTRIAL HYGIENE PRACTICE. REFER
TO OTHER SECTIONS OF THIS SDS FOR INFORMATION REGARDING PHYSICAL AND HEALTH
HAZARDS, RESPIRATORY PROTECTION, VENTILATION, AND PERSONAL PROTECTIVE
EQUIPMENT.
6.2. ENVIRONMENTAL PRECAUTIONS:
AVOID RELEASE TO THE ENVIRONMENT. FOR LARGER SPILLS, COVER DRAINS AND BUILD
DIKES TO PREVENT ENTRY INTO SEWER SYSTEMS OR BODIES OF WATER.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP:
CONTAIN SPILL. WORKING FROM AROUND THE EDGES OF THE SPILL INWARD, COVER
WITH BENTONITE, VERMICULITE, OR COMMERCIALLY AVAILABLE INORGANIC ABSORBENT
MATERIAL. MIX IN SUFFICIENT ABSORBENT UNTIL IT APPEARS DRY. REMEMBER,
ADDING AN ABSORBENT MATERIAL DOES NOT REMOVE A PHYSICAL, HEALTH, OR
ENVIRONMENTAL HAZARD. COLLECT AS MUCH OF THE SPILLED MATERIAL AS POSSIBLE.
PLACE IN A CLOSED CONTAINER APPROVED FOR TRANSPORTATION BY APPROPRIATE
AUTHORITIES. CLEAN UP RESIDUE WITH WATER. SEAL THE CONTAINER. DISPOSE OF
COLLECTED MATERIAL AS SOON AS POSSIBLE IN ACCORDANCE WITH APPLICABLE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
FOR INDUSTRIAL OR PROFESSIONAL USE ONLY. THIS PRODUCT IS NOT INTENDED
TO BE USED WITHOUT PRIOR DILUTION AS SPECIFIED ON THE PRODUCT LABEL.
GROUNDING OR SAFETY SHOES WITH ELECTROSTATIC DISSIPATING SOLES (ESD)
ARE NOT REQUIRED WITH A CHEMICAL DISPENSING SYSTEM. KEEP OUT OF REACH
OF CHILDREN. AVOID BREATHING DUST/FUME/GAS/MIST/VAPORS/SPRAY. DO NOT
GET IN EYES, ON SKIN, OR ON CLOTHING. DO NOT EAT, DRINK OR SMOKE WHEN
USING THIS PRODUCT. WASH THOROUGHLY AFTER HANDLING. CONTAMINATED WORK
CLOTHING SHOULD NOT BE ALLOWED OUT OF THE WORKPLACE. AVOID RELEASE TO
THE ENVIRONMENT. WASH CONTAMINATED CLOTHING BEFORE REUSE.
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
NO SPECIAL STORAGE REQUIREMENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
NO OCCUPATIONAL EXPOSURE LIMIT VALUES EXIST FOR ANY OF THE COMPONENTS
LISTED IN SECTION 3 OF THIS SDS.
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
NOTE:
WHEN USED WITH A CHEMICAL DISPENSING SYSTEM AS DIRECTED, SPECIAL
VENTILATION IS NOT REQUIRED. USE GENERAL DILUTION VENTILATION AND/OR
LOCAL EXHAUST VENTILATION TO CONTROL AIRBORNE EXPOSURES TO BELOW
RELEVANT EXPOSURE LIMITS AND/OR CONTROL DUST/FUME/GAS/MIST/VAPORS/SPRAY.
IF VENTILATION IS NOT ADEQUATE, USE RESPIRATORY PROTECTION EQUIPMENT.
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
NOTE:
WHEN USED WITH A CHEMICAL DISPENSING SYSTEM AS DIRECTED, EYE CONTACT WITH
THE CONCENTRATE IS NOT EXPECTED TO OCCUR. IF THE PRODUCT IS NOT USED WITH
A CHEMICAL DISPENSING SYSTEM OR IF THERE IS AN ACCIDENTAL RELEASE, WEAR
PROTECTIVE EYE/FACE PROTECTION.
IF PRODUCT IS NOT USED WITH A CHEMICAL DISPENSING SYSTEM OR IF THERE IS AN
ACCIDENTAL RELEASE:
SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON THE RESULTS
OF AN EXPOSURE ASSESSMENT.
THE FOLLOWING EYE/FACE PROTECTION(S) ARE RECOMMENDED:
INDIRECT VENTED GOGGLES
SKIN/HAND PROTECTION:
NOTE:
WHEN USED WITH A CHEMICAL DISPENSING SYSTEM AS DIRECTED, SKIN CONTACT
WITH THE CONCENTRATE IS NOT EXPECTED TO OCCUR. IF PRODUCT IS NOT USED
WITH A CHEMICAL DISPENSING SYSTEM OR IF THERE IS AN ACCIDENTAL RELEASE:
SELECT AND USE GLOVES AND/OR PROTECTIVE CLOTHING APPROVED TO RELEVANT
LOCAL STANDARDS TO PREVENT SKIN CONTACT BASED ON THE RESULTS OF AN
EXPOSURE ASSESSMENT. SELECTION SHOULD BE BASED ON USE FACTORS SUCH AS
EXPOSURE LEVELS, CONCENTRATION OF THE SUBSTANCE OR MIXTURE, FREQUENCY
AND DURATION, PHYSICAL CHALLENGES SUCH AS TEMPERATURE EXTREMES, AND
OTHER USE CONDITIONS. CONSULT WITH YOUR GLOVE AND/OR PROTECTIVE CLOTHING
MANUFACTURER FOR SELECTION OF APPROPRIATE COMPATIBLE GLOVES/PROTECTIVE
CLOTHING.
NOTE:
NITRILE GLOVES MAY BE WORN OVER POLYMER LAMINATE GLOVES TO IMPROVE
DEXTERITY.
GLOVES MADE FROM THE FOLLOWING MATERIAL(S) ARE RECOMMENDED:
POLYMER LAMINATE
IF THIS PRODUCT IS USED IN A MANNER THAT PRESENTS A HIGHER POTENTIAL FOR
EXPOSURE (EG. SPRAYING, HIGH SPLASH POTENTIAL ETC.), THEN USE OF PROTECTIVE
COVERALLS MAY BE NECESSARY.
IF PRODUCT IS NOT USED WITH A CHEMICAL DISPENSING SYSTEM OR IF THERE IS AN
ACCIDENTAL RELEASE:
SELECT AND USE BODY PROTECTION TO PREVENT CONTACT BASED ON THE RESULTS OF
AN EXPOSURE ASSESSMENT.
THE FOLLOWING PROTECTIVE CLOTHING MATERIAL(S) ARE RECOMMENDED:
APRON - POLYMER LAMINATE
RESPIRATORY PROTECTION:
NOTE:
WHEN USED WITH A CHEMICAL DISPENSING SYSTEM AS DIRECTED, RESPIRATORY
PROTECTION IS NOT REQUIRED.
IF PRODUCT IS NOT USED WITH A CHEMICAL DISPENSING SYSTEM OR IF THERE IS AN
ACCIDENTAL RELEASE:
AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF A RESPIRATOR IS REQUIRED.
IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS PART OF A FULL RESPIRATORY
PROTECTION PROGRAM.
BASED ON THE RESULTS OF THE EXPOSURE ASSESSMENT, SELECT FROM THE FOLLOWING
RESPIRATOR TYPE(S) TO REDUCE INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
ORGANIC VAPORS AND PARTICULATES
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: LIQUID
SPECIFIC PHYSICAL FORM: LIQUID
ODOR, COLOR, GRADE: CLEAR, GREEN COLOR, PLEASANT FRAGRANCE
ODOR THRESHOLD: NO DATA AVAILABLE
PH: 8.5 - 10.5
MELTING POINT: NOT APPLICABLE
BOILING POINT: APPROXIMATELY 210 DEG. F
FLASH POINT: NO FLASH POINT
EVAPORATION RATE: NO DATA AVAILABLE
FLAMMABILITY (SOLID, GAS): NOT APPLICABLE
FLAMMABLE LIMITS(LEL): NOT APPLICABLE
FLAMMABLE LIMITS(UEL): NOT APPLICABLE
VAPOR PRESSURE: 17.5 MMHg [@ 68 DEG. F]
VAPOR DENSITY: NO DATA AVAILABLE
DENSITY: 11.1
SPECIFIC GRAVITY: 1 - 1.1 [REF STD:WATER=1]
SOLUBILITY IN WATER: COMPLETE
SOLUBILITY- NON-WATER: NO DATA AVAILABLE
PARTITION COEFFICIENT N-OCTANOL/ WATER: NO DATA AVAILABLE
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
DECOMPOSITION TEMPERATURE: NO DATA AVAILABLE
VISCOSITY: 15.8 - 17.4 SAYBOLT UNIVERSAL SECOND
VOLATILE ORGANIC COMPOUNDS:
0 % WEIGHT [TEST METHOD: CALCULATED PER CARB TITLE 2]
VOC LESS H2O & EXEMPT SOLVENTS:
0 G/L [TEST METHOD: CALCULATED PER CARB TITLE 2]
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL IS CONSIDERED TO BE NON REACTIVE UNDER NORMAL USE CONDITIONS.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID: NONE KNOWN.
10.5. INCOMPATIBLE MATERIALS: NONE KNOWN.
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR THE
SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT BELOW
THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
RESPIRATORY TRACT IRRITATION: SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING,
NASAL DISCHARGE, HEADACHE, HOARSENESS, AND NOSE AND THROAT PAIN.
SKIN CONTACT:
SKIN IRRITATION: SIGNS/SYMPTOMS MAY INCLUDE LOCALIZED REDNESS, SWELLING,
ITCHING, DRYNESS, CRACKING, BLISTERING, AND PAIN. ALLERGIC SKIN REACTION
(NON-PHOTO INDUCED): SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING,
BLISTERING, AND ITCHING.
PHOTOSENSITIZATION:
SIGNS/SYMPTOMS MAY INCLUDE A SUNBURN-LIKE REACTION SUCH AS BLISTERING,
REDNESS, SWELLING, AND ITCHING FROM MINOR EXPOSURE TO SUNLIGHT.
EYE CONTACT:
SEVERE EYE IRRITATION: SIGNS/SYMPTOMS MAY INCLUDE SIGNIFICANT REDNESS,
SWELLING, PAIN, TEARING, CLOUDY APPEARANCE OF THE CORNEA, AND IMPAIRED
VISION.
INGESTION:
GASTROINTESTINAL IRRITATION: SIGNS/SYMPTOMS MAY INCLUDE ABDOMINAL PAIN,
STOMACH UPSET, NAUSEA, VOMITING AND DIARRHEA.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT INGESTION NO DATA AVAILABLE;
CALCULATED ATE
>5,000 MG/KG
SODIUM CHLORIDE DERMAL RABBIT LD50 >10,000 MG/KG
SODIUM CHLORIDE INHALATION- RAT LC50 >10.5 MG/L
DUST/MIST
(4 HOURS)
SODIUM CHLORIDE INGESTION RAT LD50 3,550 MG/KG
FRAGRANCE DERMAL RABBIT LD50 >5,000 MG/KG
(NJTSN
04499600-6540)
FRAGRANCE INGESTION RAT LD50 4,498 MG/KG
(NJTSN
04499600-6540)
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
OVERALL PRODUCT IN VITRO DATA IRRITANT
SODIUM CHLORIDE RABBIT NO SIGNIFICANT IRRITATION
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
OVERALL PRODUCT IN VITRO DATA SEVERE IRRITANT
SODIUM CHLORIDE RABBIT MILD IRRITANT
SKIN SENSITIZATION:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
RESPIRATORY SENSITIZATION:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
SODIUM CHLORIDE IN VITRO SOME POSITIVE DATA EXIST, BUT THE
DATA ARE NOT SUFFICIENT FOR
CLASSIFICATION
SODIUM CHLORIDE IN VIVO SOME POSITIVE DATA EXIST, BUT THE
DATA ARE NOT SUFFICIENT FOR
CLASSIFICATION
CARCINOGENICITY:
NAME ROUTE SPECIES VALUE
SODIUM CHLORIDE INGESTION RAT NOT CARCINOGENIC
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
SODIUM CHLORIDE INGESTION BLOOD | KIDNEY SOME POSITIVE DATA
AND/OR BLADDER | EXIST, BUT THE DATA
VASCULAR SYSTEM ARE NOT SUFFICIENT
FOR CLASSIFICATION
SODIUM CHLORIDE INGESTION NERVOUS SYSTEM | SOME POSITIVE DATA
EYES EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
SODIUM CHLORIDE INGESTION LIVER | NOT CLASSIFIED
RESPIRATORY
SYSTEM
NAME SPECIES TEST RESULT EXPOSURE DURATION
SODIUM CHLORIDE RAT NOAEL 9 MONTHS
2,240
MG/KG/DAY
SODIUM CHLORIDE RAT NOAEL 90 DAYS
1,700
MG/KG/DAY
SODIUM CHLORIDE RAT NOAEL 33 90 DAYS
MG/KG/DAY
ASPIRATION HAZARD:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
A 3M PRODUCT ENVIRONMENTAL DATA SHEET (PED) IS AVAILABLE.
CHEMICAL FATE INFORMATION:
A 3M PRODUCT ENVIRONMENTAL DATA SHEET (PED) IS AVAILABLE.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/ CONTAINER IN ACCORDANCE WITH THE LOCAL/REGIONAL/
NATIONAL/INTERNATIONAL REGULATIONS.
DISPOSE OF WASTE PRODUCT IN A PERMITTED INDUSTRIAL WASTE FACILITY. EMPTY
DRUMS/BARRELS/CONTAINERS USED FOR TRANSPORTING AND HANDLING HAZARDOUS
CHEMICALS (CHEMICAL SUBSTANCES/MIXTURES/PREPARATIONS CLASSIFIED AS
HAZARDOUS AS PER APPLICABLE REGULATIONS) SHALL BE CONSIDERED, STORED,
TREATED & DISPOSED OF AS HAZARDOUS WASTES UNLESS OTHERWISE DEFINED BY
APPLICABLE WASTE REGULATIONS. CONSULT WITH THE RESPECTIVE REGULATING
AUTHORITIES TO DETERMINE THE AVAILABLE TREATMENT AND DISPOSAL FACILITIES.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
| SECTION 14: TRANSPORT INFORMATION | |
FOR TRANSPORT INFORMATION, PLEASE VISIT:
HTTP://3M.COM/TRANSPORTINFO OR CALL 1-800-364-3577 OR 651-737-6501.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS:
311/312 HAZARD CATEGORIES:
FIRE HAZARD: NO
PRESSURE HAZARD: NO
REACTIVITY HAZARD: NO
IMMEDIATE HAZARD: YES
DELAYED HAZARD: NO
EPCRA 311/312 HAZARD CLASSIFICATIONS (EFFECTIVE JANUARY 1, 2018):
PHYSICAL HAZARDS: NOT APPLICABLE
HEALTH HAZARDS:
SERIOUS EYE DAMAGE OR EYE IRRITATION
SKIN CORROSION OR IRRITATION
15.2. STATE REGULATIONS:
15.3. CHEMICAL INVENTORIES:
THE COMPONENTS OF THIS MATERIAL ARE IN COMPLIANCE WITH THE PROVISIONS OF
AUSTRALIA NATIONAL INDUSTRIAL CHEMICAL NOTIFICATION AND ASSESSMENT SCHEME
(NICNAS). CERTAIN RESTRICTIONS MAY APPLY. CONTACT THE SELLING DIVISION FOR
ADDITIONAL INFORMATION.
THE COMPONENTS OF THIS MATERIAL ARE IN COMPLIANCE WITH THE CHINA "MEASURES
ON ENVIRONMENTAL MANAGEMENT OF NEW CHEMICAL SUBSTANCE". CERTAIN
RESTRICTIONS MAY APPLY. CONTACT THE SELLING DIVISION FOR ADDITIONAL
INFORMATION.
THE COMPONENTS OF THIS PRODUCT ARE IN COMPLIANCE WITH THE CHEMICAL
NOTIFICATION REQUIREMENTS OF TSCA.
THIS PRODUCT COMPLIES WITH THE NEW ZEALAND HAZARDOUS SUBSTANCES AND NEW
ORGANISMS ACT (1996).
15.4. INTERNATIONAL REGULATIONS:
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 2
FLAMMABILITY 0
INSTABILITY 0
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED
FOR USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS
OF FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY
BASED ON THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL
BUT ALSO INCLUDE THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION
PRODUCTS THAT ARE KNOWN TO BE GENERATED IN SIGNIFICANT QUANTITIES.
HMIS HAZARD CLASSIFICATION:
HEALTH 2
FLAMMABILITY 0
PHYSICAL HAZARD 0
PERSONAL PROTECTION X - SEE PPE SECTION.
HAZARDOUS MATERIAL IDENTIFICATION SYSTEM (HMIS(R*) IV) HAZARD RATINGS
ARE DESIGNED TO INFORM EMPLOYEES OF CHEMICAL HAZARDS IN THE WORKPLACE.
THESE RATINGS ARE BASED ON THE INHERENT PROPERTIES OF THE MATERIAL
UNDER EXPECTED CONDITIONS OF NORMAL USE AND ARE NOT INTENDED FOR USE
IN EMERGENCY SITUATIONS. HMIS(R*) IV RATINGS ARE TO BE USED WITH A
FULLY IMPLEMENTED HMIS(R*) IV PROGRAM. HMIS(R*) IS A REGISTERED MARK
OF THE AMERICAN COATINGS ASSOCIATION (ACA).
DOCUMENT GROUP: 07-8343-1
ISSUE DATE: 08/22/17
VERSION NUMBER: 9.00
SUPERCEDES DATE: 06/27/16
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED.3MMAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE3MPRODUCT IS FIT FOR
A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND APPLICATION OF A
3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S KNOWLEDGE AND
CONTROL,IT IS ESSENTIAL THAT THE USER EVALUATE THE3MPRODUCT TO DETERMINE
WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD
OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION,3MMAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM