| Common Name: | ABRASIVE PRODUCTS, 302D, 304D, 332D P100-P180 |
| Manufacturer: | 3M |
| SDS Revision Date: | 10/17/2016 |
| SDS Format: | GHS-US |
| Item Number(s): | 4ZR32 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M(TM) ABRASIVE PRODUCTS, 302D, 304D, 332D P100-P180
10/17/16
3M
SAFETY DATA SHEET
COPYRIGHT, 2016, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR THE
PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 26-5759-1
VERSION NUMBER: 2.10
ISSUE DATE: 10/17/16
SUPERCEDES DATE: 04/01/14
| SECTION 1: IDENTIFICATION |  |
1.1. PRODUCT IDENTIFIER:
3M(TM) ABRASIVE PRODUCTS, 302D, 304D, 332D P100-P180
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE: ABRASIVE PRODUCT
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: ABRASIVE SYSTEMS DIVISION
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
NOT CLASSIFIED AS HAZARDOUS ACCORDING TO OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
2.2. LABEL ELEMENTS:
SIGNAL WORD: NOT APPLICABLE.
SYMBOLS: NOT APPLICABLE.
PICTOGRAMS: NOT APPLICABLE.
2.3. HAZARDS NOT OTHERWISE CLASSIFIED: NONE.
22% OF THE MIXTURE CONSISTS OF INGREDIENTS OF UNKNOWN ACUTE ORAL TOXICITY.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
ALUMINUM OXIDE MINERAL (NON-FIBROUS) 1344-28-1 10 - 55
FILLER 1317-65-3 1 - 20
INORGANIC FLUORIDE 15096-52-3 0.5 - 20
TITANIUM DIOXIDE 13463-67-7 0.1 - 3
PIGMENT 1332-37-2 0 - 1
QUARTZ SILICA 14808-60-7 0.001 - 0.4
COLORANT BLEND MIXTURE 0 - 1
CURED RESIN MIXTURE 0.5 - 25
CLOTH BACKING MIXTURE 20 - 65
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
WASH WITH SOAP AND WATER. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL ATTENTION.
EYE CONTACT:
FLUSH WITH LARGE AMOUNTS OF WATER. REMOVE CONTACT LENSES IF EASY TO DO.
CONTINUE RINSING. IF SIGNS/SYMPTOMS PERSIST, GET MEDICAL ATTENTION.
IF SWALLOWED: NO NEED FOR FIRST AID IS ANTICIPATED.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED: NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
IN CASE OF FIRE:
USE A FIRE FIGHTING AGENT SUITABLE FOR ORDINARY COMBUSTIBLE MATERIAL SUCH
AS WATER OR FOAM TO EXTINGUISH.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
NONE INHERENT IN THIS PRODUCT.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
NO SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS ARE ANTICIPATED.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
OBSERVE PRECAUTIONS FROM OTHER SECTIONS.
6.2. ENVIRONMENTAL PRECAUTIONS: AVOID RELEASE TO THE ENVIRONMENT.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP: NOT APPLICABLE.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
FOR INDUSTRIAL OR PROFESSIONAL USE ONLY. AVOID BREATHING OF DUST CREATED BY
SANDING, GRINDING OR MACHINING. DAMAGED PRODUCT CAN BREAK APART DURING USE
AND CAUSE SERIOUS INJURY TO FACE OR EYES. CHECK PRODUCT FOR DAMAGE SUCH AS
CRACKS OR NICKS PRIOR TO USE. REPLACE IF DAMAGED. ALWAYS WEAR EYE AND FACE
PROTECTION WHEN WORKING AT SANDING OR GRINDING OPERATIONS OR WHEN NEAR SUCH
OPERATIONS. SPARKS AND PARTICLES FLYING FROM THE PRODUCT DURING SANDING OR
GRINDING CAN CAUSE INJURY AND FIRE. AVOID RELEASE TO THE ENVIRONMENT.
COMBUSTIBLE DUST MAY FORM BY ACTION OF THIS PRODUCT ON ANOTHER MATERIAL
(SUBSTRATE). DUST GENERATED FROM THE SUBSTRATE DURING USE OF THIS PRODUCT
MAY BE EXPLOSIVE IF IN SUFFICIENT CONCENTRATION WITH AN IGNITION SOURCE.
DUST DEPOSITS SHOULD NOT BE ALLOWED TO ACCUMULATE ON SURFACES BECAUSE OF
THE POTENTIAL FOR SECONDARY EXPLOSIONS.
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
NO SPECIAL STORAGE REQUIREMENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN THE TABLE
BELOW, AN OCCUPATIONAL EXPOSURE LIMIT IS NOT AVAILABLE FOR THE COMPONENT.
INGREDIENT C.A.S. NO. AGENCY LIMIT TYPE ADDITIONAL
COMMENTS
FILLER 1317-65-3 OSHA TWA (AS TOTAL
DUST): 15 MG/M3
TWA (RESPIRABLE
FRACTION): 5 MG/M3
ALUMINUM, INSOLUBLE 1344-28-1 ACGIH TWA (RESPIRABLE A4:
COMPOUNDS FRACTION): 1 MG/M3 NOT CLASS.
AS HUMAN
CARCIN
ALUMINUM OXIDE 1344-28-1 OSHA TWA (AS TOTAL
MINERAL (NON- DUST): 15 MG/M3
FIBROUS)
TWA (RESPIRABLE
FRACTION): 5 MG/M3
TITANIUM DIOXIDE 13463-67-7 ACGIH TWA: 10 MG/M3 A4:
NOT CLASS.
AS HUMAN
CARCIN
TITANIUM DIOXIDE 13463-67-7 OSHA TWA (AS TOTAL
DUST): 15 MG/M3
QUARTZ SILICA 14808-60-7 ACGIH TWA (RESPIRABLE A2:
FRACTION): SUSPECTED
0.025 MG/M3 HUMAN
CARCIN.
QUARTZ SILICA 14808-60-7 OSHA TWA CONCENTRATION
(RESPIRABLE):
0.1 MG/M3 (2.4
MILLIONS OF
PARTICLES/CU. FT.)
TWA: 0.05 MG/M3
ALUMINUM, INSOLUBLE 15096-52-3 ACGIH TWA (RESPIRABLE A4:
COMPOUNDS FRACTION): 1 MG/M3 NOT CLASS.
AS HUMAN
CARCIN
FLUORIDES 15096-52-3 ACGIH TWA (AS F): A4:
2.5 MG/M3 NOT CLASS.
AS HUMAN
CARCIN
FLUORIDES 15096-52-3 OSHA TWA (AS DUST):
2.5 MG/M3
TWA (AS F):
2.5 MG/M3
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
AIHA: AMERICAN INDUSTRIAL HYGIENE ASSOCIATION
CMRG: CHEMICAL MANUFACTURER'S RECOMMENDED GUIDELINES
OSHA:
UNITED STATES DEPARTMENT OF LABOR - OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION
TWA: TIME-WEIGHTED-AVERAGE
STEL: SHORT TERM EXPOSURE LIMIT
CEIL: CEILING
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO
CONTROL AIRBORNE EXPOSURES TO BELOW RELEVANT EXPOSURE LIMITS AND/OR CONTROL
DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS NOT ADEQUATE, USE
RESPIRATORY PROTECTION EQUIPMENT. PROVIDE APPROPRIATE LOCAL EXHAUST
VENTILATION FOR SANDING, GRINDING OR MACHINING. PROVIDE LOCAL EXHAUST AT
PROCESS EMISSION SOURCES TO CONTROL EXPOSURE NEAR THE SOURCE AND TO PREVENT
THE ESCAPE OF DUST INTO THE WORK AREA. ENSURE THAT DUST-HANDLING SYSTEMS
(SUCH AS EXHAUST DUCTS, DUST COLLECTORS, VESSELS, AND PROCESSING EQUIPMENT)
ARE DESIGNED IN A MANNER TO PREVENT THE ESCAPE OF DUST INTO THE WORK AREA
(I.E., THERE IS NO LEAKAGE FROM THE EQUIPMENT).
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
TO MINIMIZE THE RISK OF INJURY TO FACE AND EYES, ALWAYS WEAR EYE AND FACE
PROTECTION WHEN WORKING AT SANDING OR GRINDING OPERATIONS OR WHEN NEAR SUCH
OPERATIONS. SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON
THE RESULTS OF AN EXPOSURE ASSESSMENT. THE FOLLOWING EYE/FACE PROTECTION(S)
ARE RECOMMENDED: SAFETY GLASSES WITH SIDE SHIELDS
SKIN/HAND PROTECTION:
WEAR APPROPRIATE GLOVES TO MINIMIZE RISK OF INJURY TO SKIN FROM CONTACT
WITH DUST OR PHYSICAL ABRASION FROM GRINDING OR SANDING.
RESPIRATORY PROTECTION:
ASSESS EXPOSURE CONCENTRATIONS OF ALL MATERIALS INVOLVED IN THE WORK
PROCESS. CONSIDER MATERIAL BEING ABRADED WHEN DETERMINING THE APPROPRIATE
RESPIRATORY PROTECTION. SELECT AND USE APPROPRIATE RESPIRATORS TO PREVENT
INHALATION OVEREXPOSURE. AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF
A RESPIRATOR IS REQUIRED. IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS
PART OF A FULL RESPIRATORY PROTECTION PROGRAM. BASED ON THE RESULTS OF THE
EXPOSURE ASSESSMENT, SELECT FROM THE FOLLOWING RESPIRATOR TYPE(S) TO REDUCE
INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
PARTICULATES
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: SOLID
ODOR, COLOR, GRADE: SOLID ABRASIVE PRODUCT
ODOR THRESHOLD: NOT APPLICABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: NOT APPLICABLE
FLASH POINT: NOT APPLICABLE
FLAMMABILITY (SOLID, GAS): NOT CLASSIFIED
FLAMMABLE LIMITS (LEL): NOT APPLICABLE
FLAMMABLE LIMITS (UEL): NOT APPLICABLE
VAPOR PRESSURE: NOT APPLICABLE
VAPOR DENSITY: NOT APPLICABLE
SPECIFIC GRAVITY: NO DATA AVAILABLE
SOLUBILITY IN WATER: NOT APPLICABLE
SOLUBILITY- NON-WATER: NOT APPLICABLE
AUTOIGNITION TEMPERATURE: NOT APPLICABLE
DECOMPOSITION TEMPERATURE: NOT APPLICABLE
VISCOSITY: NOT APPLICABLE
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL IS CONSIDERED TO BE NON REACTIVE UNDER NORMAL USE CONDITIONS.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID: NONE KNOWN.
10.5. INCOMPATIBLE MATERIALS: NONE KNOWN.
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR THE
SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT BELOW
THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
DUST FROM GRINDING, SANDING OR MACHINING MAY CAUSE IRRITATION OF THE
RESPIRATORY SYSTEM. SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL
DISCHARGE, HEADACHE, HOARSENESS, AND NOSE AND THROAT PAIN.
SKIN CONTACT:
MECHANICAL SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABRASION, REDNESS, PAIN, AND ITCHING.
EYE CONTACT:
MECHANICAL EYE IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE PAIN, REDNESS, TEARING AND CORNEAL ABRASION.
DUST CREATED BY GRINDING, SANDING, OR MACHINING MAY CAUSE EYE IRRITATION.
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND BLURRED OR
HAZY VISION.
INGESTION: NO KNOWN HEALTH EFFECTS.
CARCINOGENICITY:
INGREDIENT CAS NO. CLASS DESCRIPTION REGULATION
SILICA, CRYS 14808-60-7 KNOWN HUMAN CARCINOGEN NATIONAL TOXICOLOGY
AIRRESP PROGRAM CARCINOGENS
QUARTZ SILICA 14808-60-7 GRP. 1: INTERNATIONAL AGENCY
CARCINOGENIC TO HUMANS FOR RESEARCH ON CANCER
TITANIUM 13463-67-7 GRP. 2B: INTERNATIONAL AGENCY
DIOXIDE POSSIBLE HUMAN CARC. FOR RESEARCH ON CANCER
ADDITIONAL INFORMATION:
THIS PRODUCT CONTAINS TITANIUM DIOXIDE AND QUARTZ (CRYSTALLINE) SILICA.
CANCER OF THE LUNGS HAS BEEN ASSOCIATED WITH INHALATION OF HIGH LEVELS OF
TITANIUM DIOXIDE IN ANIMAL STUDIES, AND OCCUPATIONAL EXPOSURE TO INHALED
QUARTZ SILICA HAS BEEN ASSOCIATED WITH SILICOSIS AND LUNG CANCER. NO
EXPOSURE TO TITANIUM DIOXIDE OR QUARTZ SILICA IS EXPECTED DURING THE NORMAL
HANDLING AND USE OF THIS PRODUCT. TITANIUM DIOXIDE AND QUARTZ SILICA WERE
NOT DETECTED WHEN AIR SAMPLING WAS CONDUCTED DURING SIMULATED USE OF
SIMILAR PRODUCTS CONTAINING THESE SUBSTANCES. THEREFORE, THE HEALTH EFFECTS
ASSOCIATED WITH TITANIUM DIOXIDE AND QUARTZ (CRYSTALLINE) SILICA ARE NOT
EXPECTED DURING THE NORMAL USE OF THIS PRODUCT.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT INGESTION NO DATA AVAILABLE;
CALCULATED ATE:
>5,000 MG/KG
ALUMINUM OXIDE MINERAL DERMAL LD50:
(NON-FIBROUS) ESTIMATED TO BE
>5,000 MG/KG
ALUMINUM OXIDE MINERAL INHALATION- RAT LC50: >2.3 MG/L
(NON-FIBROUS) DUST/MIST
(4 HOURS)
ALUMINUM OXIDE MINERAL INGESTION RAT LD50: >5,000 MG/KG
(NON-FIBROUS)
INORGANIC FLUORIDE DERMAL RABBIT LD50: >2,100 MG/KG
FILLER DERMAL RAT LD50: >2,000 MG/KG
FILLER INHALATION- RAT LC50: 3 MG/L
DUST/MIST
(4 HOURS)
FILLER INGESTION RAT LD50: 6,450 MG/KG
INORGANIC FLUORIDE INHALATION- RAT LC50: 4.5 MG/L
DUST/MIST
(4 HOURS)
INORGANIC FLUORIDE INGESTION RAT LD50: 5,000 MG/KG
TITANIUM DIOXIDE DERMAL RABBIT LD50: >10,000 MG/KG
TITANIUM DIOXIDE INHALATION- RAT LC50: >6.82 MG/L
DUST/MIST
(4 HOURS)
TITANIUM DIOXIDE INGESTION RAT LD50: >10,000 MG/KG
PIGMENT DERMAL NOT LD50: 3,100 MG/KG
AVAILABLE
PIGMENT INGESTION NOT LD50: 3,700 MG/KG
AVAILABLE
QUARTZ SILICA DERMAL LD50:
ESTIMATED TO BE
>5,000 MG/KG
QUARTZ SILICA INGESTION LD50:
ESTIMATED TO BE
>5,000 MG/KG
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
ALUMINUM OXIDE MINERAL RABBIT NO SIGNIFICANT IRRITATION
(NON-FIBROUS)
FILLER RABBIT NO SIGNIFICANT IRRITATION
INORGANIC FLUORIDE MULTIPLE NO SIGNIFICANT IRRITATION
ANIMAL
SPECIES
TITANIUM DIOXIDE RABBIT NO SIGNIFICANT IRRITATION
PIGMENT RABBIT NO SIGNIFICANT IRRITATION
QUARTZ SILICA PROFESSIONAL NO SIGNIFICANT IRRITATION
JUDGEMENT
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
ALUMINUM OXIDE MINERAL RABBIT NO SIGNIFICANT IRRITATION
(NON-FIBROUS)
FILLER RABBIT NO SIGNIFICANT IRRITATION
INORGANIC FLUORIDE RABBIT MILD IRRITANT
TITANIUM DIOXIDE RABBIT NO SIGNIFICANT IRRITATION
PIGMENT RABBIT NO SIGNIFICANT IRRITATION
SKIN SENSITIZATION:
NAME SPECIES VALUE
TITANIUM DIOXIDE HUMAN NOT SENSITIZING
AND
ANIMAL
PIGMENT HUMAN SOME POSITIVE DATA EXIST,
BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
RESPIRATORY SENSITIZATION:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
ALUMINUM OXIDE MINERAL IN VITRO NOT MUTAGENIC
(NON-FIBROUS)
TITANIUM DIOXIDE IN VITRO NOT MUTAGENIC
TITANIUM DIOXIDE IN VIVO NOT MUTAGENIC
PIGMENT IN VITRO NOT MUTAGENIC
QUARTZ SILICA IN VITRO SOME POSITIVE DATA EXIST,
BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
QUARTZ SILICA IN VIVO SOME POSITIVE DATA EXIST,
BUT THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
CARCINOGENICITY:
NAME ROUTE SPECIES VALUE
ALUMINUM OXIDE MINERAL INHALATION RAT NOT CARCINOGENIC
(NON-FIBROUS)
TITANIUM DIOXIDE INGESTION MULTIPLE NOT CARCINOGENIC
ANIMAL
SPECIES
TITANIUM DIOXIDE INHALATION RAT CARCINOGENIC
PIGMENT INHALATION HUMAN SOME POSITIVE DATA
EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
QUARTZ SILICA INHALATION HUMAN CARCINOGENIC
AND
ANIMAL
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
NAME ROUTE VALUE
FILLER INGESTION NOT TOXIC TO DEVELOPMENT
NAME SPECIES TEST RESULT EXPOSURE DURATION
FILLER RAT NOAEL: 625 MG/KG/DAY PREMATING & DURING
GESTATION
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
FILLER INHALATION RESPIRATORY SYSTEM ALL DATA ARE NEGATIVE
NAME SPECIES TEST RESULT EXPOSURE DURATION
FILLER RAT NOAEL: 0.812 MG/L 90 MINUTES
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
ALUMINUM OXIDE INHALATION PNEUMOCONIOSIS SOME POSITIVE DATA
MINERAL (NON-FIBROUS) PULMONARY FIBROSIS EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
FILLER INHALATION RESPIRATORY SYSTEM SOME POSITIVE DATA
EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
INORGANIC FLUORIDE INHALATION BONE, TEETH, NAILS, CAUSES DAMAGE TO
AND/OR HAIR ORGANS THROUGH
PROLONGED OR
REPEATED EXPOSURE
INORGANIC FLUORIDE INHALATION RESPIRATORY SYSTEM CAUSES DAMAGE TO
ORGANS THROUGH
PROLONGED OR
REPEATED EXPOSURE
INORGANIC FLUORIDE INGESTION BONE, TEETH, NAILS, CAUSES DAMAGE TO
AND/OR HAIR ORGANS THROUGH
PROLONGED OR
REPEATED EXPOSURE
TITANIUM DIOXIDE INHALATION RESPIRATORY SYSTEM SOME POSITIVE DATA
EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
TITANIUM DIOXIDE INHALATION PULMONARY FIBROSIS ALL DATA ARE
NEGATIVE
PIGMENT INHALATION PULMONARY FIBROSIS SOME POSITIVE DATA
PNEUMOCONIOSIS EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
QUARTZ SILICA INHALATION SILICOSIS CAUSES DAMAGE TO
ORGANS THROUGH
PROLONGED OR
REPEATED EXPOSURE
NAME SPECIES TEST RESULT EXPOSURE DURATION
ALUMINUM OXIDE HUMAN NOAEL: NOT AVAILABLE OCCUPATIONAL
MINERAL EXPOSURE
(NON-FIBROUS)
FILLER HUMAN NOAEL: NOT AVAILABLE OCCUPATIONAL
EXPOSURE
INORGANIC RAT NOAEL: 0.0005 MG/L 5 MONTHS
FLUORIDE
INORGANIC RAT NOAEL: 0.00021 MG/L 90 DAYS
FLUORIDE
INORGANIC RAT LOAEL: 0.58 MG/KG/DAY 14 WEEKS
FLUORIDE
TITANIUM DIOXIDE RAT LOAEL: 0.01 MG/L 2 YEARS
TITANIUM DIOXIDE HUMAN NOAEL: NOT AVAILABLE OCCUPATIONAL
EXPOSURE
PIGMENT HUMAN NOAEL: NOT AVAILABLE OCCUPATIONAL
EXPOSURE
QUARTZ SILICA HUMAN NOAEL: NOT AVAILABLE OCCUPATIONAL
EXPOSURE
ASPIRATION HAZARD:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/ CONTAINER IN ACCORDANCE WITH THE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
THE SUBSTRATE THAT WAS ABRADED MUST BE CONSIDERED AS A FACTOR IN THE
DISPOSAL METHOD FOR THIS PRODUCT. INCINERATE IN A PERMITTED WASTE
INCINERATION FACILITY. PROPER DESTRUCTION MAY REQUIRE THE USE OF ADDITIONAL
FUEL DURING INCINERATION PROCESSES. AS A DISPOSAL ALTERNATIVE, UTILIZE AN
ACCEPTABLE PERMITTED WASTE DISPOSAL FACILITY.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
| SECTION 14: TRANSPORT INFORMATION | |
NOT REGULATED PER U.S. DOT, IATA OR IMO.
THESE TRANSPORTATION CLASSIFICATIONS ARE PROVIDED AS A CUSTOMER SERVICE. AS
THE SHIPPER YOU REMAIN RESPONSIBLE FOR COMPLYING WITH ALL APPLICABLE LAWS
AND REGULATIONS, INCLUDING PROPER TRANSPORTATION CLASSIFICATION AND
PACKAGING. 3M TRANSPORTATION CLASSIFICATIONS ARE BASED ON PRODUCT
FORMULATION, PACKAGING, 3M POLICIES AND 3M UNDERSTANDING OF APPLICABLE
CURRENT REGULATIONS. 3M DOES NOT GUARANTEE THE ACCURACY OF THIS
CLASSIFICATION INFORMATION. THIS INFORMATION APPLIES ONLY TO TRANSPORTATION
CLASSIFICATION AND NOT THE PACKAGING, LABELING, OR MARKING REQUIREMENTS.
THE ORIGINAL 3M PACKAGE IS CERTIFIED FOR U.S. GROUND SHIPMENT ONLY. IF YOU
ARE SHIPPING BY AIR OR OCEAN, THE PACKAGE MAY NOT MEET APPLICABLE
REGULATORY REQUIREMENTS.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
311/312 HAZARD CATEGORIES:
FIRE HAZARD: NO
PRESSURE HAZARD: NO
REACTIVITY HAZARD: NO
IMMEDIATE HAZARD: NO
DELAYED HAZARD: NO
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
15.3. CHEMICAL INVENTORIES:
THIS PRODUCT IS AN ARTICLE AS DEFINED BY TSCA REGULATIONS, AND IS EXEMPT
FROM TSCA INVENTORY LISTING REQUIREMENTS.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 0
FLAMMABILITY 1
INSTABILITY 0
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED FOR
USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO INCLUDE
THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT ARE KNOWN
TO BE GENERATED IN SIGNIFICANT QUANTITIES.
HMIS HAZARD CLASSIFICATION:
HEALTH 0
FLAMMABILITY 1
PHYSICAL HAZARD 0
PERSONAL PROTECTION X - SEE PPE SECTION.
HAZARDOUS MATERIAL IDENTIFICATION SYSTEM (HMIS(R*) IV) HAZARD RATINGS ARE
DESIGNED TO INFORM EMPLOYEES OF CHEMICAL HAZARDS IN THE WORKPLACE. THESE
RATINGS ARE BASED ON THE INHERENT PROPERTIES OF THE MATERIAL UNDER EXPECTED
CONDITIONS OF NORMAL USE AND ARE NOT INTENDED FOR USE IN EMERGENCY
SITUATIONS. HMIS(R*) IV RATINGS ARE TO BE USED WITH A FULLY IMPLEMENTED
HMIS(R*) IV PROGRAM. HMIS(R*) IS A REGISTERED MARK OF THE AMERICAN COATINGS
ASSOCIATION (ACA).
DOCUMENT GROUP: 26-5759-1
VERSION NUMBER: 2.10
ISSUE DATE: 10/17/16
SUPERCEDES DATE: 04/01/14
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED IN
ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM