| Common Name: | ALKYD DRY FALL FLAT WHITE |
| Manufacturer: | KRYLON PRODUCTS |
| SDS Revision Date: | 9/16/2016 |
| SDS Format: | GHS-US |
| Item Number(s): | 52JN63 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
SAFETY DATA SHEET
K00E34111
| SECTION 1. IDENTIFICATION |  |
PRODUCT NAME: KRYLON(R*) ALKYD DRY FALL FLAT WHITE
PRODUCT CODE: K00E34111
OTHER MEANS OF IDENTIFICATION: NOT AVAILABLE.
CAS #: NOT APPLICABLE.
PRODUCT TYPE: LIQUID.
RELEVANT IDENTIFIED USES OF THE SUBSTANCE OR MIXTURE AND USES ADVISED
AGAINST: NOT APPLICABLE.
MANUFACTURER:
KRYLON PRODUCTS GROUP
CLEVELAND, OH 44115
EMERGENCY TELEPHONE NUMBER OF THE COMPANY: (216) 566-2917
PRODUCT INFORMATION TELEPHONE NUMBER: (800) 247-3266
REGULATORY INFORMATION TELEPHONE NUMBER: (216) 566-2902
TRANSPORTATION EMERGENCY TELEPHONE NUMBER: (800) 424-9300
| SECTION 2. HAZARDS IDENTIFICATION | |
OSHA/HCS STATUS:
THIS MATERIAL IS CONSIDERED HAZARDOUS BY THE OSHA HAZARD COMMUNICATION
STANDARD (29 CFR 1910.1200).
CLASSIFICATION OF THE SUBSTANCE OR MIXTURE:
FLAMMABLE LIQUIDS: CATEGORY 3
CARCINOGENICITY: CATEGORY 2
TOXIC TO REPRODUCTION (UNBORN CHILD): CATEGORY 2
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE): CATEGORY 2
ASPIRATION HAZARD: CATEGORY 1
PERCENTAGE OF THE MIXTURE CONSISTING OF INGREDIENT(S) OF UNKNOWN TOXICITY:
21%
GHS LABEL ELEMENTS:
HAZARD PICTOGRAMS:
FLAME
HEALTH HAZARD
SIGNAL WORD: DANGER
HAZARD STATEMENTS:
FLAMMABLE LIQUID AND VAPOR.
SUSPECTED OF DAMAGING THE UNBORN CHILD.
SUSPECTED OF CAUSING CANCER.
MAY BE FATAL IF SWALLOWED AND ENTERS AIRWAYS.
MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.
PRECAUTIONARY STATEMENTS:
PREVENTION:
OBTAIN SPECIAL INSTRUCTIONS BEFORE USE. DO NOT HANDLE UNTIL ALL SAFETY
PRECAUTIONS HAVE BEEN READ AND UNDERSTOOD. WEAR PROTECTIVE GLOVES. WEAR EYE
OR FACE PROTECTION. WEAR PROTECTIVE CLOTHING. KEEP AWAY FROM HEAT, HOT
SURFACES, SPARKS, OPEN FLAMES AND OTHER IGNITION SOURCES. NO SMOKING. USE
EXPLOSION-PROOF ELECTRICAL, VENTILATING, LIGHTING AND ALL MATERIAL-HANDLING
EQUIPMENT. USE ONLY NON-SPARKING TOOLS. TAKE PRECAUTIONARY MEASURES AGAINST
STATIC DISCHARGE. KEEP CONTAINER TIGHTLY CLOSED. DO NOT BREATHE VAPOR.
RESPONSE: GET MEDICAL ATTENTION IF YOU FEEL UNWELL.
IF EXPOSED OR CONCERNED: GET MEDICAL ATTENTION.
IF SWALLOWED:
IMMEDIATELY CALL A POISON CENTER OR PHYSICIAN. DO NOT INDUCE VOMITING.
IF ON SKIN (OR HAIR):
TAKE OFF IMMEDIATELY ALL CONTAMINATED CLOTHING. RINSE SKIN WITH WATER OR
SHOWER.
STORAGE: STORE LOCKED UP. STORE IN A WELL-VENTILATED PLACE. KEEP COOL.
DISPOSAL:
DISPOSE OF CONTENTS AND CONTAINER IN ACCORDANCE WITH ALL LOCAL, REGIONAL,
NATIONAL AND INTERNATIONAL REGULATIONS.
SUPPLEMENTAL LABEL ELEMENTS:
DANGER:
RAGS, STEEL WOOL, OTHER WASTE SOAKED WITH THIS PRODUCT, AND SANDING RESIDUE
MAY SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED. IMMEDIATELY PLACE
RAGS, STEEL WOOL, OTHER WASTE SOAKED WITH THIS PRODUCT, AND SANDING RESIDUE
IN A SEALED, WATER-FILLED, METAL CONTAINER. DISPOSE OF IN ACCORDANCE WITH
LOCAL FIRE REGULATIONS. DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE.
CONTAINS SOLVENTS WHICH CAN CAUSE PERMANENT BRAIN AND NERVOUS SYSTEM
DAMAGE. INTENTIONAL MISUSE BY DELIBERATELY CONCENTRATING AND INHALING THE
CONTENTS CAN BE HARMFUL OR FATAL.
WARNING:
THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE
CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. FOR INDUSTRIAL USE
ONLY. ADEQUATE VENTILATION REQUIRED WHEN SANDING OR ABRADING THE DRIED
FILM. IF ADEQUATE VENTILATION CANNOT BE PROVIDED WEAR AN APPROVED
PARTICULATE RESPIRATOR (NIOSH APPROVED). FOLLOW RESPIRATOR MANUFACTURER'S
DIRECTIONS FOR RESPIRATOR USE. DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE.
ABRADING OR SANDING OF THE DRY FILM MAY RELEASE CRYSTALLINE SILICA WHICH
HAS BEEN SHOWN TO CAUSE LUNG DAMAGE AND CANCER UNDER LONG TERM EXPOSURE.
PLEASE REFER TO THE SDS FOR ADDITIONAL INFORMATION. KEEP OUT OF REACH OF
CHILDREN. DO NOT TRANSFER CONTENTS TO OTHER CONTAINERS FOR STORAGE.
HAZARDS NOT OTHERWISE CLASSIFIED: NONE KNOWN.
| SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS | |
SUBSTANCE/MIXTURE: MIXTURE
OTHER MEANS OF IDENTIFICATION: NOT AVAILABLE.
CAS NUMBER/OTHER IDENTIFIERS:
INGREDIENT NAME % BY WEIGHT CAS NUMBER
LT. ALIPHATIC HYDROCARBON SOLVENT 10.58 64742-89-8
TITANIUM DIOXIDE 7.12 13463-67-7
MED. ALIPHATIC HYDROCARBON SOLVENT 3.28 64742-88-7
TOLUENE 0.15 108-88-3
ANY CONCENTRATION SHOWN AS A RANGE IS TO PROTECT CONFIDENTIALITY OR IS DUE
TO BATCH VARIATION.
THERE ARE NO ADDITIONAL INGREDIENTS PRESENT WHICH, WITHIN THE CURRENT
KNOWLEDGE OF THE SUPPLIER AND IN THE CONCENTRATIONS APPLICABLE, ARE
CLASSIFIED AS HAZARDOUS TO HEALTH AND HENCE REQUIRE REPORTING IN THIS
SECTION.
OCCUPATIONAL EXPOSURE LIMITS, IF AVAILABLE, ARE LISTED IN SECTION 8.
| SECTION 4. FIRST AID MEASURES | |
DESCRIPTION OF NECESSARY FIRST AID MEASURES:
EYE CONTACT:
IMMEDIATELY FLUSH EYES WITH PLENTY OF WATER, OCCASIONALLY LIFTING THE UPPER
AND LOWER EYELIDS. CHECK FOR AND REMOVE ANY CONTACT LENSES. CONTINUE TO
RINSE FOR AT LEAST 10 MINUTES. GET MEDICAL ATTENTION.
INHALATION:
REMOVE VICTIM TO FRESH AIR AND KEEP AT REST IN A POSITION COMFORTABLE FOR
BREATHING. IF NOT BREATHING, IF BREATHING IS IRREGULAR OR IF RESPIRATORY
ARREST OCCURS, PROVIDE ARTIFICIAL RESPIRATION OR OXYGEN BY TRAINED
PERSONNEL. IT MAY BE DANGEROUS TO THE PERSON PROVIDING AID TO GIVE
MOUTH-TO-MOUTH RESUSCITATION. GET MEDICAL ATTENTION. IF UNCONSCIOUS, PLACE
IN RECOVERY POSITION AND GET MEDICAL ATTENTION IMMEDIATELY. MAINTAIN AN
OPEN AIRWAY. LOOSEN TIGHT CLOTHING SUCH AS A COLLAR, TIE, BELT OR
WAISTBAND.
SKIN CONTACT:
FLUSH CONTAMINATED SKIN WITH PLENTY OF WATER. REMOVE CONTAMINATED CLOTHING
AND SHOES. CONTINUE TO RINSE FOR AT LEAST 10 MINUTES. GET MEDICAL
ATTENTION. WASH CLOTHING BEFORE REUSE. CLEAN SHOES THOROUGHLY BEFORE REUSE.
INGESTION:
GET MEDICAL ATTENTION IMMEDIATELY. CALL A POISON CENTER OR PHYSICIAN. WASH
OUT MOUTH WITH WATER. REMOVE DENTURES IF ANY. REMOVE VICTIM TO FRESH AIR
AND KEEP AT REST IN A POSITION COMFORTABLE FOR BREATHING. IF MATERIAL HAS
BEEN SWALLOWED AND THE EXPOSED PERSON IS CONSCIOUS, GIVE SMALL QUANTITIES
OF WATER TO DRINK. STOP IF THE EXPOSED PERSON FEELS SICK AS VOMITING MAY BE
DANGEROUS. ASPIRATION HAZARD IF SWALLOWED. CAN ENTER LUNGS AND CAUSE
DAMAGE. DO NOT INDUCE VOMITING. IF VOMITING OCCURS, THE HEAD SHOULD BE
KEPT LOW SO THAT VOMIT DOES NOT ENTER THE LUNGS. NEVER GIVE ANYTHING BY
MOUTH TO AN UNCONSCIOUS PERSON. IF UNCONSCIOUS, PLACE IN RECOVERY POSITION
AND GET MEDICAL ATTENTION IMMEDIATELY. MAINTAIN AN OPEN AIRWAY. LOOSEN
TIGHT CLOTHING SUCH AS A COLLAR, TIE, BELT OR WAISTBAND.
MOST IMPORTANT SYMPTOMS/EFFECTS, ACUTE AND DELAYED:
POTENTIAL ACUTE HEALTH EFFECTS:
EYE CONTACT: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
INHALATION: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
SKIN CONTACT: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
INGESTION: MAY BE FATAL IF SWALLOWED AND ENTERS AIRWAYS.
OVER-EXPOSURE SIGNS/SYMPTOMS:
EYE CONTACT: NO SPECIFIC DATA.
INHALATION:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
REDUCED FETAL WEIGHT
INCREASE IN FETAL DEATHS
SKELETAL MALFORMATIONS
SKIN CONTACT:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
REDUCED FETAL WEIGHT
INCREASE IN FETAL DEATHS
SKELETAL MALFORMATIONS
INGESTION:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
NAUSEA OR VOMITING
REDUCED FETAL WEIGHT
INCREASE IN FETAL DEATHS
SKELETAL MALFORMATIONS
INDICATION OF IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT NEEDED, IF
NECESSARY:
NOTES TO PHYSICIAN:
TREAT SYMPTOMATICALLY. CONTACT POISON TREATMENT SPECIALIST IMMEDIATELY IF
LARGE QUANTITIES HAVE BEEN INGESTED OR INHALED.
SPECIFIC TREATMENTS: NO SPECIFIC TREATMENT.
PROTECTION OF FIRST-AIDERS:
NO ACTION SHALL BE TAKEN INVOLVING ANY PERSONAL RISK OR WITHOUT SUITABLE
TRAINING. IT MAY BE DANGEROUS TO THE PERSON PROVIDING AID TO GIVE
MOUTH-TO-MOUTH RESUSCITATION.
SEE TOXICOLOGICAL INFORMATION (SECTION 11)
| SECTION 5. FIRE-FIGHTING MEASURES | |
EXTINGUISHING MEDIA:
SUITABLE EXTINGUISHING MEDIA:
USE DRY CHEMICAL, CO2, WATER SPRAY (FOG) OR FOAM.
UNSUITABLE EXTINGUISHING MEDIA: DO NOT USE WATER JET.
SPECIFIC HAZARDS ARISING FROM THE CHEMICAL:
FLAMMABLE LIQUID AND VAPOR. IN A FIRE OR IF HEATED, A PRESSURE INCREASE
WILL OCCUR AND THE CONTAINER MAY BURST, WITH THE RISK OF A SUBSEQUENT
EXPLOSION. RUNOFF TO SEWER MAY CREATE FIRE OR EXPLOSION HAZARD.
HAZARDOUS THERMAL DECOMPOSITION PRODUCTS:
DECOMPOSITION PRODUCTS MAY INCLUDE THE FOLLOWING MATERIALS:
CARBON DIOXIDE
CARBON MONOXIDE
METAL OXIDE/OXIDES
SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
PROMPTLY ISOLATE THE SCENE BY REMOVING ALL PERSONS FROM THE VICINITY OF THE
INCIDENT IF THERE IS A FIRE. NO ACTION SHALL BE TAKEN INVOLVING ANY
PERSONAL RISK OR WITHOUT SUITABLE TRAINING. MOVE CONTAINERS FROM FIRE AREA
IF THIS CAN BE DONE WITHOUT RISK. USE WATER SPRAY TO KEEP FIRE-EXPOSED
CONTAINERS COOL.
SPECIAL PROTECTIVE EQUIPMENT FOR FIRE-FIGHTERS:
FIRE-FIGHTERS SHOULD WEAR APPROPRIATE PROTECTIVE EQUIPMENT AND
SELF-CONTAINED BREATHING APPARATUS (SCBA) WITH A FULL FACE-PIECE OPERATED
IN POSITIVE PRESSURE MODE.
| SECTION 6. ACCIDENTAL RELEASE MEASURES | |
PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
FOR NON-EMERGENCY PERSONNEL:
NO ACTION SHALL BE TAKEN INVOLVING ANY PERSONAL RISK OR WITHOUT SUITABLE
TRAINING. EVACUATE SURROUNDING AREAS. KEEP UNNECESSARY AND UNPROTECTED
PERSONNEL FROM ENTERING. DO NOT TOUCH OR WALK THROUGH SPILLED MATERIAL.
SHUT OFF ALL IGNITION SOURCES. NO FLARES, SMOKING OR FLAMES IN HAZARD AREA.
AVOID BREATHING VAPOR OR MIST. PROVIDE ADEQUATE VENTILATION. WEAR
APPROPRIATE RESPIRATOR WHEN VENTILATION IS INADEQUATE. PUT ON APPROPRIATE
PERSONAL PROTECTIVE EQUIPMENT.
FOR EMERGENCY RESPONDERS:
IF SPECIALIZED CLOTHING IS REQUIRED TO DEAL WITH THE SPILLAGE, TAKE NOTE OF
ANY INFORMATION IN SECTION 8 ON SUITABLE AND UNSUITABLE MATERIALS. SEE ALSO
THE INFORMATION IN "FOR NON-EMERGENCY PERSONNEL".
ENVIRONMENTAL PRECAUTIONS:
AVOID DISPERSAL OF SPILLED MATERIAL AND RUNOFF AND CONTACT WITH SOIL,
WATERWAYS, DRAINS AND SEWERS. INFORM THE RELEVANT AUTHORITIES IF THE
PRODUCT HAS CAUSED ENVIRONMENTAL POLLUTION (SEWERS, WATERWAYS, SOIL
OR AIR).
METHODS AND MATERIALS FOR CONTAINMENT AND CLEANING UP:
SMALL SPILL:
STOP LEAK IF WITHOUT RISK. MOVE CONTAINERS FROM SPILL AREA. USE SPARK-PROOF
TOOLS AND EXPLOSION-PROOF EQUIPMENT. DILUTE WITH WATER AND MOP UP IF
WATER-SOLUBLE. ALTERNATIVELY, OR IF WATER-INSOLUBLE, ABSORB WITH AN INERT
DRY MATERIAL AND PLACE IN AN APPROPRIATE WASTE DISPOSAL CONTAINER. DISPOSE
OF VIA A LICENSED WASTE DISPOSAL CONTRACTOR.
LARGE SPILL:
STOP LEAK IF WITHOUT RISK. MOVE CONTAINERS FROM SPILL AREA. USE SPARK-PROOF
TOOLS AND EXPLOSION-PROOF EQUIPMENT. APPROACH RELEASE FROM UPWIND. PREVENT
ENTRY INTO SEWERS, WATER COURSES, BASEMENTS OR CONFINED AREAS. WASH
SPILLAGES INTO AN EFFLUENT TREATMENT PLANT OR PROCEED AS FOLLOWS. CONTAIN
AND COLLECT SPILLAGE WITH NON-COMBUSTIBLE, ABSORBENT MATERIAL E.G. SAND,
EARTH, VERMICULITE OR DIATOMACEOUS EARTH AND PLACE IN CONTAINER FOR
DISPOSAL ACCORDING TO LOCAL REGULATIONS (SEE SECTION 13). DISPOSE OF VIA A
LICENSED WASTE DISPOSAL CONTRACTOR. CONTAMINATED ABSORBENT MATERIAL MAY
POSE THE SAME HAZARD AS THE SPILLED PRODUCT.
NOTE:
SEE SECTION 1 FOR EMERGENCY CONTACT INFORMATION AND SECTION 13 FOR WASTE
DISPOSAL.
| SECTION 7. HANDLING AND STORAGE | |
PRECAUTIONS FOR SAFE HANDLING:
PROTECTIVE MEASURES:
PUT ON APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT (SEE SECTION 8). AVOID
EXPOSURE -OBTAIN SPECIAL INSTRUCTIONS BEFORE USE. AVOID EXPOSURE DURING
PREGNANCY. DO NOT HANDLE UNTIL ALL SAFETY PRECAUTIONS HAVE BEEN READ AND
UNDERSTOOD. DO NOT GET IN EYES OR ON SKIN OR CLOTHING. DO NOT BREATHE VAPOR
OR MIST. DO NOT SWALLOW. USE ONLY WITH ADEQUATE VENTILATION. WEAR
APPROPRIATE RESPIRATOR WHEN VENTILATION IS INADEQUATE. DO NOT ENTER STORAGE
AREAS AND CONFINED SPACES UNLESS ADEQUATELY VENTILATED. KEEP IN THE
ORIGINAL CONTAINER OR AN APPROVED ALTERNATIVE MADE FROM A COMPATIBLE
MATERIAL, KEPT TIGHTLY CLOSED WHEN NOT IN USE. STORE AND USE AWAY FROM
HEAT, SPARKS, OPEN FLAME OR ANY OTHER IGNITION SOURCE. USE EXPLOSION-PROOF
ELECTRICAL (VENTILATING, LIGHTING AND MATERIAL HANDLING) EQUIPMENT. USE
ONLY NON-SPARKING TOOLS. TAKE PRECAUTIONARY MEASURES AGAINST ELECTROSTATIC
DISCHARGES. EMPTY CONTAINERS RETAIN PRODUCT RESIDUE AND CAN BE HAZARDOUS.
DO NOT REUSE CONTAINER.
ADVICE ON GENERAL OCCUPATIONAL HYGIENE:
EATING, DRINKING AND SMOKING SHOULD BE PROHIBITED IN AREAS WHERE THIS
MATERIAL IS HANDLED, STORED AND PROCESSED. WORKERS SHOULD WASH HANDS AND
FACE BEFORE EATING, DRINKING AND SMOKING. REMOVE CONTAMINATED CLOTHING AND
PROTECTIVE EQUIPMENT BEFORE ENTERING EATING AREAS. SEE ALSO SECTION 8 FOR
ADDITIONAL INFORMATION ON HYGIENE MEASURES.
CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPATIBILITIES:
STORE IN ACCORDANCE WITH LOCAL REGULATIONS. STORE IN A SEGREGATED AND
APPROVED AREA. STORE IN ORIGINAL CONTAINER PROTECTED FROM DIRECT SUNLIGHT
IN A DRY, COOL AND WELL-VENTILATED AREA, AWAY FROM INCOMPATIBLE MATERIALS
(SEE SECTION 10) AND FOOD AND DRINK. STORE LOCKED UP. ELIMINATE ALL
IGNITION SOURCES. SEPARATE FROM OXIDIZING MATERIALS. KEEP CONTAINER TIGHTLY
CLOSED AND SEALED UNTIL READY FOR USE. CONTAINERS THAT HAVE BEEN OPENED
MUST BE CAREFULLY RESEALED AND KEPT UPRIGHT TO PREVENT LEAKAGE. DO NOT
STORE IN UNLABELED CONTAINERS. USE APPROPRIATE CONTAINMENT TO AVOID
ENVIRONMENTAL CONTAMINATION.
| SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION | |
CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS (OSHA UNITED STATES):
INGREDIENT NAME EXPOSURE LIMITS
LT. ALIPHATIC HYDROCARBON SOLVENT NONE.
TITANIUM DIOXIDE ACGIH TLV (UNITED STATES, 3/2015).
TWA: 10 MG/M3 8 HOURS.
OSHA PEL (UNITED STATES, 2/2013).
TWA: 15 MG/M3 8 HOURS.
FORM: TOTAL DUST
MED. ALIPHATIC HYDROCARBON SOLVENT OSHA PEL (UNITED STATES, 2/2013).
TWA: 100 PPM 8 HOURS.
TWA: 400 MG/M3 8 HOURS.
TOLUENE OSHA PEL Z2 (UNITED STATES, 2/2013).
TWA: 200 PPM 8 HOURS.
CEIL: 300 PPM
AMP: 500 PPM 10 MINUTES.
NIOSH REL (UNITED STATES, 10/2013).
TWA: 100 PPM 10 HOURS.
TWA: 375 MG/M3 10 HOURS.
STEL: 150 PPM 15 MINUTES.
STEL: 560 MG/M3 15 MINUTES.
ACGIH TLV (UNITED STATES, 3/2015).
TWA: 20 PPM 8 HOURS.
OCCUPATIONAL EXPOSURE LIMITS (CANADA):
INGREDIENT NAME EXPOSURE LIMITS
TOLUENE CA ALBERTA PROVINCIAL (CANADA, 4/2009).
ABSORBED THROUGH SKIN.
8 HRS OEL: 50 PPM 8 HOURS.
8 HRS OEL: 188 MG/M3 8 HOURS.
CA BRITISH COLUMBIA PROVINCIAL (CANADA, 5/2015).
TWA: 20 PPM 8 HOURS.
CA ONTARIO PROVINCIAL (CANADA, 7/2015).
TWA: 20 PPM 8 HOURS.
CA QUEBEC PROVINCIAL (CANADA, 1/2014).
ABSORBED THROUGH SKIN.
TWAEV: 50 PPM 8 HOURS.
TWAEV: 188 MG/M3 8 HOURS.
CA SASKATCHEWAN PROVINCIAL (CANADA, 7/2013).
ABSORBED THROUGH SKIN.
STEL: 60 PPM 15 MINUTES.
TWA: 50 PPM 8 HOURS.
APPROPRIATE ENGINEERING CONTROLS:
USE ONLY WITH ADEQUATE VENTILATION. USE PROCESS ENCLOSURES, LOCAL EXHAUST
VENTILATION OR OTHER ENGINEERING CONTROLS TO KEEP WORKER EXPOSURE TO
AIRBORNE CONTAMINANTS BELOW ANY RECOMMENDED OR STATUTORY LIMITS. THE
ENGINEERING CONTROLS ALSO NEED TO KEEP GAS, VAPOR OR DUST CONCENTRATIONS
BELOW ANY LOWER EXPLOSIVE LIMITS. USE EXPLOSION-PROOF VENTILATION
EQUIPMENT.
ENVIRONMENTAL EXPOSURE CONTROLS:
EMISSIONS FROM VENTILATION OR WORK PROCESS EQUIPMENT SHOULD BE CHECKED TO
ENSURE THEY COMPLY WITH THE REQUIREMENTS OF ENVIRONMENTAL PROTECTION
LEGISLATION. IN SOME CASES, FUME SCRUBBERS, FILTERS OR ENGINEERING
MODIFICATIONS TO THE PROCESS EQUIPMENT WILL BE NECESSARY TO REDUCE
EMISSIONS TO ACCEPTABLE LEVELS.
INDIVIDUAL PROTECTION MEASURES:
HYGIENE MEASURES:
WASH HANDS, FOREARMS AND FACE THOROUGHLY AFTER HANDLING CHEMICAL PRODUCTS,
BEFORE EATING, SMOKING AND USING THE LAVATORY AND AT THE END OF THE WORKING
PERIOD. APPROPRIATE TECHNIQUES SHOULD BE USED TO REMOVE POTENTIALLY
CONTAMINATED CLOTHING. WASH CONTAMINATED CLOTHING BEFORE REUSING. ENSURE
THAT EYEWASH STATIONS AND SAFETY SHOWERS ARE CLOSE TO THE WORKSTATION
LOCATION.
EYE/FACE PROTECTION:
SAFETY EYEWEAR COMPLYING WITH AN APPROVED STANDARD SHOULD BE USED WHEN A
RISK ASSESSMENT INDICATES THIS IS NECESSARY TO AVOID EXPOSURE TO LIQUID
SPLASHES, MISTS, GASES OR DUSTS. IF CONTACT IS POSSIBLE, THE FOLLOWING
PROTECTION SHOULD BE WORN, UNLESS THE ASSESSMENT INDICATES A HIGHER DEGREE
OF PROTECTION: SAFETY GLASSES WITH SIDE-SHIELDS.
SKIN PROTECTION:
HAND PROTECTION:
CHEMICAL-RESISTANT, IMPERVIOUS GLOVES COMPLYING WITH AN APPROVED STANDARD
SHOULD BE WORN AT ALL TIMES WHEN HANDLING CHEMICAL PRODUCTS IF A RISK
ASSESSMENT INDICATES THIS IS NECESSARY. CONSIDERING THE PARAMETERS
SPECIFIED BY THE GLOVE MANUFACTURER, CHECK DURING USE THAT THE GLOVES ARE
STILL RETAINING THEIR PROTECTIVE PROPERTIES. IT SHOULD BE NOTED THAT THE
TIME TO BREAKTHROUGH FOR ANY GLOVE MATERIAL MAY BE DIFFERENT FOR DIFFERENT
GLOVE MANUFACTURERS. IN THE CASE OF MIXTURES, CONSISTING OF SEVERAL
SUBSTANCES, THE PROTECTION TIME OF THE GLOVES CANNOT BE ACCURATELY
ESTIMATED.
BODY PROTECTION:
PERSONAL PROTECTIVE EQUIPMENT FOR THE BODY SHOULD BE SELECTED BASED ON THE
TASK BEING PERFORMED AND THE RISKS INVOLVED AND SHOULD BE APPROVED BY A
SPECIALIST BEFORE HANDLING THIS PRODUCT. WHEN THERE IS A RISK OF IGNITION
FROM STATIC ELECTRICITY, WEAR ANTISTATIC PROTECTIVE CLOTHING. FOR THE
GREATEST PROTECTION FROM STATIC DISCHARGES, CLOTHING SHOULD INCLUDE
ANTI-STATIC OVERALLS, BOOTS AND GLOVES.
OTHER SKIN PROTECTION:
APPROPRIATE FOOTWEAR AND ANY ADDITIONAL SKIN PROTECTION MEASURES SHOULD BE
SELECTED BASED ON THE TASK BEING PERFORMED AND THE RISKS INVOLVED AND
SHOULD BE APPROVED BY A SPECIALIST BEFORE HANDLING THIS PRODUCT.
RESPIRATORY PROTECTION:
BASED ON THE HAZARD AND POTENTIAL FOR EXPOSURE, SELECT A RESPIRATOR THAT
MEETS THE APPROPRIATE STANDARD OR CERTIFICATION. RESPIRATORS MUST BE USED
ACCORDING TO A RESPIRATORY PROTECTION PROGRAM TO ENSURE PROPER FITTING,
TRAINING, AND OTHER IMPORTANT ASPECTS OF USE.
| SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES | |
APPEARANCE:
PHYSICAL STATE: LIQUID.
COLOR: WHITE.
ODOR: NOT AVAILABLE.
ODOR THRESHOLD: NOT AVAILABLE.
PH: 7.2
MELTING POINT: NOT AVAILABLE.
BOILING POINT: 100 DEG. C (212 DEG. F)
FLASH POINT:
CLOSED CUP: 24 DEG. C (75.2 DEG. F) [PENSKY-MARTENS CLOSED CUP]
EVAPORATION RATE: 1.5 (BUTYL ACETATE = 1)
FLAMMABILITY (SOLID, GAS): NOT AVAILABLE.
LOWER AND UPPER EXPLOSIVE (FLAMMABLE) LIMITS:
LOWER: 0.9%
UPPER: 6%
VAPOR PRESSURE: 0.31 KPA (2.333 MMHg) [AT 20 DEG. C]
VAPOR DENSITY: 1 [AIR = 1]
RELATIVE DENSITY: 1.45
SOLUBILITY: NOT AVAILABLE.
PARTITION COEFFICIENT N-OCTANOL/WATER: NOT AVAILABLE.
AUTO-IGNITION TEMPERATURE: NOT AVAILABLE.
DECOMPOSITION TEMPERATURE: NOT AVAILABLE.
VISCOSITY:
KINEMATIC (ROOM TEMPERATURE): <0.205 CM2/S (<20.5 CST)
KINEMATIC (40 DEG. C (104 DEG. F)): <0.205 CM2/S (<20.5 CST)
MOLECULAR WEIGHT: NOT APPLICABLE.
AEROSOL PRODUCT:
HEAT OF COMBUSTION: 6.481 KJ/G
| SECTION 10. STABILITY AND REACTIVITY | |
REACTIVITY:
NO SPECIFIC TEST DATA RELATED TO REACTIVITY AVAILABLE FOR THIS PRODUCT OR
ITS INGREDIENTS.
CHEMICAL STABILITY: THE PRODUCT IS STABLE.
POSSIBILITY OF HAZARDOUS REACTIONS:
UNDER NORMAL CONDITIONS OF STORAGE AND USE, HAZARDOUS REACTIONS WILL NOT
OCCUR.
CONDITIONS TO AVOID:
AVOID ALL POSSIBLE SOURCES OF IGNITION (SPARK OR FLAME). DO NOT PRESSURIZE,
CUT, WELD, BRAZE, SOLDER, DRILL, GRIND OR EXPOSE CONTAINERS TO HEAT OR
SOURCES OF IGNITION.
INCOMPATIBLE MATERIALS:
REACTIVE OR INCOMPATIBLE WITH THE FOLLOWING MATERIALS: OXIDIZING MATERIALS
HAZARDOUS DECOMPOSITION PRODUCTS:
UNDER NORMAL CONDITIONS OF STORAGE AND USE, HAZARDOUS DECOMPOSITION
PRODUCTS SHOULD NOT BE PRODUCED.
| SECTION 11. TOXICOLOGICAL INFORMATION | |
INFORMATION ON TOXICOLOGICAL EFFECTS:
ACUTE TOXICITY:
PRODUCT/INGREDIENT RESULT SPECIES DOSE EXPOSURE
NAME
TOLUENE LC50 INHALATION RAT 49 G/M3 4 HOURS
VAPOR
LD50 ORAL RAT 636 MG/KG
IRRITATION/CORROSION:
PRODUCT/INGREDIENT RESULT SPECIES SCORE EXPOSURE OBSERVATION
NAME
TITANIUM DIOXIDE SKIN: HUMAN 72 HOURS
MILD 300 MICROGRAMS
IRRITANT INTERMITTENT
TOLUENE EYES: RABBIT 0.5 MINUTES
MILD 100 MILLIGRAMS
IRRITANT
EYES: RABBIT 870 MICROGRAMS
MILD
IRRITANT
EYES: RABBIT 24 HOURS
SEVERE 2 MILLIGRAMS
IRRITANT
SKIN: PIG 24 HOURS
MILD 250 MICROLITERS
IRRITANT
SKIN: RABBIT 435 MILLIGRAMS
MILD
IRRITANT
SKIN: RABBIT 24 HOURS
MODERATE 20 MILLIGRAMS
IRRITANT
SKIN: RABBIT 500 MILLIGRAMS
MODERATE
IRRITANT
SENSITIZATION: NOT AVAILABLE.
MUTAGENICITY: NOT AVAILABLE.
CARCINOGENICITY: NOT AVAILABLE.
CLASSIFICATION:
PRODUCT/INGREDIENT NAME OSHA IARC NTP
TITANIUM DIOXIDE 2B
TOLUENE 3
REPRODUCTIVE TOXICITY: NOT AVAILABLE.
TERATOGENICITY: NOT AVAILABLE.
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE):
NAME CATEGORY ROUTE OF TARGET ORGANS
EXPOSURE
LT. ALIPHATIC HYDROCARBON CATEGORY 3 NOT APPLICABLE. RESPIRATORY TRACT
SOLVENT IRRITATION AND
NARCOTIC EFFECTS
MED. ALIPHATIC CATEGORY 3 NOT APPLICABLE. RESPIRATORY TRACT
HYDROCARBON SOLVENT IRRITATION AND
NARCOTIC EFFECTS
TOLUENE CATEGORY 3 NOT APPLICABLE. RESPIRATORY TRACT
IRRITATION AND
NARCOTIC EFFECTS
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE):
NAME CATEGORY ROUTE OF TARGET ORGANS
EXPOSURE
LT. ALIPHATIC HYDROCARBON CATEGORY 2 NOT DETERMINED NOT DETERMINED
SOLVENT
MED. ALIPHATIC HYDROCARBON CATEGORY 2 NOT DETERMINED NOT DETERMINED
SOLVENT
TOLUENE CATEGORY 2 NOT DETERMINED NOT DETERMINED
ASPIRATION HAZARD:
NAME RESULT
LT. ALIPHATIC HYDROCARBON SOLVENT ASPIRATION HAZARD - CATEGORY 1
MED. ALIPHATIC HYDROCARBON SOLVENT ASPIRATION HAZARD - CATEGORY 1
TOLUENE ASPIRATION HAZARD - CATEGORY 1
INFORMATION ON THE LIKELY ROUTES OF EXPOSURE: NOT AVAILABLE.
POTENTIAL ACUTE HEALTH EFFECTS:
EYE CONTACT: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
INHALATION: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
SKIN CONTACT: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
INGESTION: MAY BE FATAL IF SWALLOWED AND ENTERS AIRWAYS.
SYMPTOMS RELATED TO THE PHYSICAL, CHEMICAL AND TOXICOLOGICAL
CHARACTERISTICS:
EYE CONTACT: NO SPECIFIC DATA.
INHALATION:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
REDUCED FETAL WEIGHT
INCREASE IN FETAL DEATHS
SKELETAL MALFORMATIONS
SKIN CONTACT:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
REDUCED FETAL WEIGHT
INCREASE IN FETAL DEATHS
SKELETAL MALFORMATIONS
INGESTION:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
NAUSEA OR VOMITING
REDUCED FETAL WEIGHT
INCREASE IN FETAL DEATHS
SKELETAL MALFORMATIONS
DELAYED AND IMMEDIATE EFFECTS AND ALSO CHRONIC EFFECTS FROM SHORT AND LONG
TERM EXPOSURE:
SHORT TERM EXPOSURE:
POTENTIAL IMMEDIATE EFFECTS: NOT AVAILABLE.
POTENTIAL DELAYED EFFECTS: NOT AVAILABLE.
LONG TERM EXPOSURE:
POTENTIAL IMMEDIATE EFFECTS: NOT AVAILABLE.
POTENTIAL DELAYED EFFECTS: NOT AVAILABLE.
POTENTIAL CHRONIC HEALTH EFFECTS: NOT AVAILABLE.
GENERAL: MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.
CARCINOGENICITY:
SUSPECTED OF CAUSING CANCER. RISK OF CANCER DEPENDS ON DURATION AND LEVEL
OF EXPOSURE.
MUTAGENICITY: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
TERATOGENICITY: SUSPECTED OF DAMAGING THE UNBORN CHILD.
DEVELOPMENTAL EFFECTS: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
FERTILITY EFFECTS: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
NUMERICAL MEASURES OF TOXICITY:
ACUTE TOXICITY ESTIMATES: NOT AVAILABLE.
| SECTION 12. ECOLOGICAL INFORMATION | |
TOXICITY:
PRODUCT/INGREDIENT RESULT SPECIES EXPOSURE
NAME
LT. ALIPHATIC ACUTE LC50: FISH - ONCORHYNCHUS 96 HOURS
HYDROCARBON SOLVENT >100000 PPM MYKISS
FRESH WATER
TITANIUM DIOXIDE ACUTE LC50: FISH - FUNDULUS 96 HOURS
>1000000 (MICRO)G/L HETEROCLITUS
MARINE WATER
TOLUENE ACUTE EC50: ALGAE - 72 HOURS
12500 (MICRO)G/L PSEUDOKIRCHNERIELLA
FRESH WATER SUBCAPITATA
ACUTE EC50: CRUSTACEANS - 48 HOURS
11600 (MICRO)G/L GAMMARUS
FRESH WATER PSEUDOLIMNAEUS -
ADULT
ACUTE EC50: DAPHNIA - DAPHNIA 48 HOURS
6000 (MICRO)G/L MAGNA - JUVENILE
FRESH WATER (FLEDGLING,
HATCHLING,
WEANLING)
ACUTE LC50: FISH - ONCORHYNCHUS 96 HOURS
5500 (MICRO)G/L KISUTCH - FRY
FRESH WATER
CHRONIC NOEC: DAPHNIA - DAPHNIA 21 DAYS
1000 (MICRO)G/L MAGNA
FRESH WATER
PERSISTENCE AND DEGRADABILITY:
PRODUCT/INGREDIENT NAME AQUATIC HALF-LIFE PHOTOLYSIS BIODEGRADABILITY
TOLUENE READILY
BIOACCUMULATIVE POTENTIAL:
PRODUCT/INGREDIENT NAME LOGPOW BCF POTENTIAL
LT. ALIPHATIC HYDROCARBON SOLVENT 10 TO 2500 HIGH
TOLUENE 90 LOW
MOBILITY IN SOIL:
SOIL/WATER PARTITION COEFFICIENT (KOC): NOT AVAILABLE.
OTHER ADVERSE EFFECTS: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
| SECTION 13. DISPOSAL CONSIDERATIONS | |
DISPOSAL METHODS:
THE GENERATION OF WASTE SHOULD BE AVOIDED OR MINIMIZED WHEREVER POSSIBLE.
DISPOSAL OF THIS PRODUCT, SOLUTIONS AND ANY BY-PRODUCTS SHOULD AT ALL TIMES
COMPLY WITH THE REQUIREMENTS OF ENVIRONMENTAL PROTECTION AND WASTE DISPOSAL
LEGISLATION AND ANY REGIONAL LOCAL AUTHORITY REQUIREMENTS. DISPOSE OF
SURPLUS AND NON-RECYCLABLE PRODUCTS VIA A LICENSED WASTE DISPOSAL
CONTRACTOR. WASTE SHOULD NOT BE DISPOSED OF UNTREATED TO THE SEWER UNLESS
FULLY COMPLIANT WITH THE REQUIREMENTS OF ALL AUTHORITIES WITH JURISDICTION.
WASTE PACKAGING SHOULD BE RECYCLED. INCINERATION OR LANDFILL SHOULD ONLY BE
CONSIDERED WHEN RECYCLING IS NOT FEASIBLE. THIS MATERIAL AND ITS CONTAINER
MUST BE DISPOSED OF IN A SAFE WAY. CARE SHOULD BE TAKEN WHEN HANDLING
EMPTIED CONTAINERS THAT HAVE NOT BEEN CLEANED OR RINSED OUT. EMPTY
CONTAINERS OR LINERS MAY RETAIN SOME PRODUCT RESIDUES. VAPOR FROM PRODUCT
RESIDUES MAY CREATE A HIGHLY FLAMMABLE OR EXPLOSIVE ATMOSPHERE INSIDE THE
CONTAINER. DO NOT CUT, WELD OR GRIND USED CONTAINERS UNLESS THEY HAVE BEEN
CLEANED THOROUGHLY INTERNALLY. AVOID DISPERSAL OF SPILLED MATERIAL AND
RUNOFF AND CONTACT WITH SOIL, WATERWAYS, DRAINS AND SEWERS.
| SECTION 14. TRANSPORT INFORMATION | |
DOT TDG MEXICO
CLASSIFICATION CLASSIFICATION CLASSIFICATION
UN NUMBER UN1263 UN1263 UN1263
UN PROPER SHIPPING PAINT PAINT PAINT
NAME
TRANSPORT HAZARD 3 3 3
CLASS(ES)
FLAMMABLE LIQUID, CLASS 3, CLASS 3,
CLASS/DIVISION FLAMMABLE FLAMMABLE
3.1, 3.2, 3.3 LIQUIDS LIQUIDS
PACKING GROUP III III III
ENVIRONMENTAL NO. NO. NO.
HAZARDS
ADDITIONAL PRODUCT
INFORMATION CLASSIFIED
AS PER THE
FOLLOWING
SECTIONS OF THE
TRANSPORTATION
OF DANGEROUS
GOODS
REGULATIONS:
2.
18-2.19
(CLASS 3).
ERG NO.: 128 ERG NO.: ERG NO.:
128 128
IATA IMDG
UN NUMBER UN1263 UN1263
UN PROPER SHIPPING NAME PAINT PAINT
TRANSPORT HAZARD CLASS(ES) 3 3
CLASS 3, CLASS 3 - FLAMMABLE
FLAMMABLE LIQUIDS LIQUIDS
PACKING GROUP III III
ENVIRONMENTAL HAZARDS NO. NO.
ADDITIONAL INFORMATION EMERGENCY
SCHEDULES (EMS):
F-E, S-E
SPECIAL PRECAUTIONS FOR USER:
MULTI-MODAL SHIPPING DESCRIPTIONS ARE PROVIDED FOR INFORMATIONAL PURPOSES
AND DO NOT CONSIDER CONTAINER SIZES. THE PRESENCE OF A SHIPPING DESCRIPTION
FOR A PARTICULAR MODE OF TRANSPORT (SEA, AIR, ETC.), DOES NOT INDICATE THAT
THE PRODUCT IS PACKAGED SUITABLY FOR THAT MODE OF TRANSPORT. ALL PACKAGING
MUST BE REVIEWED FOR SUITABILITY PRIOR TO SHIPMENT, AND COMPLIANCE WITH THE
APPLICABLE REGULATIONS IS THE SOLE RESPONSIBILITY OF THE PERSON OFFERING
THE PRODUCT FOR TRANSPORT. PEOPLE LOADING AND UNLOADING DANGEROUS GOODS
MUST BE TRAINED ON ALL OF THE RISKS DERIVING FROM THE SUBSTANCES AND ON ALL
ACTIONS IN CASE OF EMERGENCY SITUATIONS.
TRANSPORT IN BULK ACCORDING TO ANNEX II OF MARPOL AND THE IBC CODE:
NOT AVAILABLE.
PROPER SHIPPING NAME: NOT AVAILABLE.
SHIP TYPE: NOT AVAILABLE.
POLLUTION CATEGORY: NOT AVAILABLE.
| SECTION 15. REGULATORY INFORMATION | |
SARA 313:
SARA 313 (40 CFR 372.45) SUPPLIER NOTIFICATION CAN BE FOUND ON THE
ENVIRONMENTAL DATA SHEET.
CALIFORNIA PROP. 65:
WARNING:
THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE
CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
| SECTION 16. OTHER INFORMATION | |
HAZARDOUS MATERIAL INFORMATION SYSTEM (U.S.A.):
HEALTH 2*
FLAMMABILITY 3
PHYSICAL HAZARDS 0
THE CUSTOMER IS RESPONSIBLE FOR DETERMINING THE PPE CODE FOR THIS MATERIAL.
CAUTION:
HMIS(R*) RATINGS ARE BASED ON A 0-4 RATING SCALE, WITH 0 REPRESENTING
MINIMAL HAZARDS OR RISKS, AND 4 REPRESENTING SIGNIFICANT HAZARDS OR RISKS
ALTHOUGH HMIS(R*) RATINGS ARE NOT REQUIRED ON SDSS UNDER 29 CFR 1910.1200,
THE PREPARER MAY CHOOSE TO PROVIDE THEM. HMIS(R*) RATINGS ARE TO BE USED
WITH A FULLY IMPLEMENTED HMIS(R*) PROGRAM. HMIS(R*) IS A REGISTERED MARK OF
THE NATIONAL PAINT & COATINGS ASSOCIATION (NPCA). HMIS(R*) MATERIALS MAY BE
PURCHASED EXCLUSIVELY FROM J. J. KELLER (800) 327-6868.
PROCEDURE USED TO DERIVE THE CLASSIFICATION:
CLASSIFICATION JUSTIFICATION
FLAMMABLE LIQUIDS - CATEGORY 3 ON BASIS OF TEST DATA
CARCINOGENICITY - CATEGORY 2 CALCULATION METHOD
TOXIC TO REPRODUCTION (UNBORN CHILD) - CATEGORY 2 CALCULATION METHOD
SPECIFIC TARGET ORGAN TOXICITY (REPEATED CALCULATION METHOD
EXPOSURE) - CATEGORY 2
ASPIRATION HAZARD - CATEGORY 1 CALCULATION METHOD
HISTORY:
DATE OF PRINTING: 9/16/2016
DATE OF ISSUE/DATE OF REVISION: 9/16/2016
DATE OF PREVIOUS ISSUE: 6/30/2016
VERSION: 4
KEY TO ABBREVIATIONS:
ATE: ACUTE TOXICITY ESTIMATE
BCF: BIOCONCENTRATION FACTOR
GHS:
GLOBALLY HARMONIZED SYSTEM OF CLASSIFICATION AND LABELLING OF CHEMICALS
IATA: INTERNATIONAL AIR TRANSPORT ASSOCIATION
IBC: INTERMEDIATE BULK CONTAINER
IMDG: INTERNATIONAL MARITIME DANGEROUS GOODS
LOGPOW: LOGARITHM OF THE OCTANOL/WATER PARTITION COEFFICIENT
MARPOL:
INTERNATIONAL CONVENTION FOR THE PREVENTION OF POLLUTION FROM SHIPS, 1973
AS MODIFIED BY THE PROTOCOL OF 1978. ("MARPOL" = MARINE POLLUTION)
UN: UNITED NATIONS
NOTICE TO READER:
IT IS RECOMMENDED THAT EACH CUSTOMER OR RECIPIENT OF THIS SAFETY DATA SHEET
(SDS) STUDY IT CAREFULLY AND CONSULT RESOURCES, AS NECESSARY OR
APPROPRIATE, TO BECOME AWARE OF AND UNDERSTAND THE DATA CONTAINED IN THIS
SDS AND ANY HAZARDS ASSOCIATED WITH THE PRODUCT. THIS INFORMATION IS
PROVIDED IN GOOD FAITH AND BELIEVED TO BE ACCURATE AS OF THE EFFECTIVE DATE
HEREIN. HOWEVER, NO WARRANTY, EXPRESS OR IMPLIED, IS GIVEN. THE INFORMATION
PRESENTED HERE APPLIES ONLY TO THE PRODUCT AS SHIPPED. THE ADDITION OF ANY
MATERIAL CAN CHANGE THE COMPOSITION, HAZARDS AND RISKS OF THE PRODUCT.
PRODUCTS SHALL NOT BE REPACKAGED, MODIFIED, OR TINTED EXCEPT AS
SPECIFICALLY INSTRUCTED BY SHERWIN-WILLIAMS, INCLUDING BUT NOT LIMITED TO
THE INCORPORATION OF NON SHERWIN-WILLIAMS PRODUCTS OR THE USE OR ADDITION
OF PRODUCTS IN PROPORTIONS NOT SPECIFIED BY SHERWIN-WILLIAMS. REGULATORY
REQUIREMENTS ARE SUBJECT TO CHANGE AND MAY DIFFER BETWEEN VARIOUS LOCATIONS
AND JURISDICTIONS. THE CUSTOMER/BUYER/USER IS RESPONSIBLE TO ENSURE THAT
HIS ACTIVITIES COMPLY WITH ALL COUNTRY, FEDERAL, STATE, PROVINCIAL OR LOCAL
LAWS. THE CONDITIONS FOR USE OF THE PRODUCT ARE NOT UNDER THE CONTROL OF
THE MANUFACTURER; THE CUSTOMER/BUYER/USER IS RESPONSIBLE TO DETERMINE THE
CONDITIONS NECESSARY FOR THE SAFE USE OF THIS PRODUCT. THE
CUSTOMER/BUYER/USER SHOULD NOT USE THE PRODUCT FOR ANY PURPOSE OTHER THAN
THE PURPOSE SHOWN IN THE APPLICABLE SECTION OF THIS SDS WITHOUT FIRST
REFERRING TO THE SUPPLIER AND OBTAINING WRITTEN HANDLING INSTRUCTIONS.
DUE TO THE PROLIFERATION OF SOURCES FOR INFORMATION SUCH AS
MANUFACTURER-SPECIFIC SDS, THE MANUFACTURER CANNOT BE RESPONSIBLE FOR SDSS
OBTAINED FROM ANY OTHER SOURCE.