| Common Name: | INDUSTRIAL ACRYLI-QUIK, STONE GRAY |
| Manufacturer: | KRYLON PRODUCTS |
| SDS Revision Date: | 5/18/2017 |
| SDS Format: | GHS-US |
| Item Number(s): | 54TG78 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
SAFETY DATA SHEET
1605
| SECTION 1. IDENTIFICATION |  |
PRODUCT NAME:
KRYLON(R*) INDUSTRIAL ACRYLI-QUIK(TM)
STONE GRAY
PRODUCT CODE: 1605
OTHER MEANS OF IDENTIFICATION: NOT AVAILABLE.
CAS #: NOT APPLICABLE.
PRODUCT TYPE: AEROSOL.
RELEVANT IDENTIFIED USES OF THE SUBSTANCE OR MIXTURE AND USES ADVISED
AGAINST: NOT APPLICABLE.
MANUFACTURER:
KRYLON PRODUCTS GROUP
101 PROSPECT AVENUE NW
CLEVELAND, OH 44115
EMERGENCY TELEPHONE NUMBER OF THE COMPANY: (216) 566-2917
PRODUCT INFORMATION TELEPHONE NUMBER: (800) 247-3266
REGULATORY INFORMATION TELEPHONE NUMBER: (216) 566-2902
TRANSPORTATION EMERGENCY TELEPHONE NUMBER: (800) 424-9300
| SECTION 2. HAZARDS IDENTIFICATION | |
OSHA/HCS STATUS:
THIS MATERIAL IS CONSIDERED HAZARDOUS BY THE OSHA HAZARD COMMUNICATION
STANDARD (29 CFR 1910.1200).
CLASSIFICATION OF THE SUBSTANCE OR MIXTURE:
FLAMMABLE AEROSOLS: CATEGORY 1
GASES UNDER PRESSURE: COMPRESSED GAS
SKIN CORROSION/IRRITATION: CATEGORY 2
SERIOUS EYE DAMAGE/ EYE IRRITATION: CATEGORY 2A
CARCINOGENICITY: CATEGORY 2
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (RESPIRATORY TRACT
IRRITATION): CATEGORY 3
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (NARCOTIC EFFECTS):
CATEGORY 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE): CATEGORY 2
ASPIRATION HAZARD: CATEGORY 1
PERCENTAGE OF THE MIXTURE CONSISTING OF INGREDIENT(S) OF UNKNOWN ACUTE
TOXICITY: 15%
GHS LABEL ELEMENTS:
HAZARD PICTOGRAMS:
FLAME
GAS CYLINDER
HEALTH HAZARD
EXCLAMATION MARK
SIGNAL WORD: DANGER
HAZARD STATEMENTS:
EXTREMELY FLAMMABLE AEROSOL.
CONTAINS GAS UNDER PRESSURE; MAY EXPLODE IF HEATED.
CAUSES SERIOUS EYE IRRITATION.
CAUSES SKIN IRRITATION.
SUSPECTED OF CAUSING CANCER.
MAY BE FATAL IF SWALLOWED AND ENTERS AIRWAYS.
MAY CAUSE RESPIRATORY IRRITATION.
MAY CAUSE DROWSINESS OR DIZZINESS.
MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.
PRECAUTIONARY STATEMENTS:
PREVENTION:
OBTAIN SPECIAL INSTRUCTIONS BEFORE USE. DO NOT HANDLE UNTIL ALL SAFETY
PRECAUTIONS HAVE BEEN READ AND UNDERSTOOD. WEAR PROTECTIVE GLOVES. WEAR
EYE OR FACE PROTECTION. WEAR PROTECTIVE CLOTHING. KEEP AWAY FROM HEAT,
HOT SURFACES, SPARKS, OPEN FLAMES AND OTHER IGNITION SOURCES. NO SMOKING.
DO NOT SPRAY ON AN OPEN FLAME OR OTHER IGNITION SOURCE. USE ONLY OUTDOORS
OR IN A WELL-VENTILATED AREA. DO NOT BREATHE DUST OR MIST. WASH HANDS
THOROUGHLY AFTER HANDLING. PRESSURIZED CONTAINER: DO NOT PIERCE OR BURN,
EVEN AFTER USE.
RESPONSE: GET MEDICAL ATTENTION IF YOU FEEL UNWELL.
IF EXPOSED OR CONCERNED: GET MEDICAL ATTENTION.
IF INHALED:
REMOVE PERSON TO FRESH AIR AND KEEP COMFORTABLE FOR BREATHING.
CALL A POISON CENTER OR PHYSICIAN IF YOU FEEL UNWELL.
IF SWALLOWED:
IMMEDIATELY CALL A POISON CENTER OR PHYSICIAN. DO NOT INDUCE VOMITING.
IF ON SKIN:
WASH WITH PLENTY OF SOAP AND WATER. TAKE OFF CONTAMINATED CLOTHING AND
WASH IT BEFORE REUSE.
IF SKIN IRRITATION OCCURS: GET MEDICAL ATTENTION.
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES,
IF PRESENT AND EASY TO DO. CONTINUE RINSING.
IF EYE IRRITATION PERSISTS: GET MEDICAL ATTENTION.
STORAGE:
STORE LOCKED UP. PROTECT FROM SUNLIGHT. DO NOT EXPOSE TO TEMPERATURES
EXCEEDING 50 DEG. C/122 DEG. F. STORE IN A WELL-VENTILATED PLACE.
DISPOSAL:
DISPOSE OF CONTENTS AND CONTAINER IN ACCORDANCE WITH ALL LOCAL, REGIONAL,
NATIONAL AND INTERNATIONAL REGULATIONS.
SUPPLEMENTAL LABEL ELEMENTS:
DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. CONTAINS SOLVENTS WHICH
CAN CAUSE PERMANENT BRAIN AND NERVOUS SYSTEM DAMAGE. INTENTIONAL MISUSE
BY DELIBERATELY CONCENTRATING AND INHALING THE CONTENTS CAN BE HARMFUL
OR FATAL.
WARNING:
THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE
CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. FOR INDUSTRIAL USE
ONLY.
PLEASE REFER TO THE SDS FOR ADDITIONAL INFORMATION. KEEP OUT OF REACH OF
CHILDREN. KEEP UPRIGHT IN A COOL, DRY PLACE. DO NOT DISCARD EMPTY CAN IN
TRASH COMPACTOR.
HAZARDS NOT OTHERWISE CLASSIFIED:
DANGER:
RAGS, STEEL WOOL, OTHER WASTE SOAKED WITH THIS PRODUCT, AND SANDING
RESIDUE MAY SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED. IMMEDIATELY
PLACE RAGS, STEEL WOOL, OTHER WASTE SOAKED WITH THIS PRODUCT, AND SANDING
RESIDUE IN A SEALED, WATER-FILLED, METAL CONTAINER. DISPOSE OF IN
ACCORDANCE WITH LOCAL FIRE REGULATIONS.
| SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS | |
SUBSTANCE/MIXTURE: MIXTURE
OTHER MEANS OF IDENTIFICATION: NOT AVAILABLE.
CAS NUMBER/OTHER IDENTIFIERS:
INGREDIENT NAME % BY WEIGHT CAS NUMBER
METHYL ACETATE 35 79-20-9
METHYL ETHYL KETONE 19.91 78-93-3
PROPANE 13.6 74-98-6
BUTANE 6.4 106-97-8
1-METHOXY-2-PROPANOL ACETATE 6.35 108-65-6
XYLENE 3.45 1330-20-7
TITANIUM DIOXIDE 1.45 13463-67-7
ACETONE 1.31 67-64-1
ETHYLBENZENE 0.61 100-41-4
ANY CONCENTRATION SHOWN AS A RANGE IS TO PROTECT CONFIDENTIALITY OR IS
DUE TO BATCH VARIATION.
THERE ARE NO ADDITIONAL INGREDIENTS PRESENT WHICH, WITHIN THE CURRENT
KNOWLEDGE OF THE SUPPLIER AND IN THE CONCENTRATIONS APPLICABLE, ARE
CLASSIFIED AS HAZARDOUS TO HEALTH AND HENCE REQUIRE REPORTING IN THIS
SECTION.
OCCUPATIONAL EXPOSURE LIMITS, IF AVAILABLE, ARE LISTED IN SECTION 8.
| SECTION 4. FIRST AID MEASURES | |
DESCRIPTION OF NECESSARY FIRST AID MEASURES:
EYE CONTACT:
IMMEDIATELY FLUSH EYES WITH PLENTY OF WATER, OCCASIONALLY LIFTING THE
UPPER AND LOWER EYELIDS. CHECK FOR AND REMOVE ANY CONTACT LENSES. CONTINUE
TO RINSE FOR AT LEAST 10 MINUTES. GET MEDICAL ATTENTION.
INHALATION:
REMOVE VICTIM TO FRESH AIR AND KEEP AT REST IN A POSITION COMFORTABLE FOR
BREATHING. IF IT IS SUSPECTED THAT FUMES ARE STILL PRESENT, THE RESCUER
SHOULD WEAR AN APPROPRIATE MASK OR SELF-CONTAINED BREATHING APPARATUS. IF
NOT BREATHING, IF BREATHING IS IRREGULAR OR IF RESPIRATORY ARREST OCCURS,
PROVIDE ARTIFICIAL RESPIRATION OR OXYGEN BY TRAINED PERSONNEL. IT MAY
BE DANGEROUS TO THE PERSON PROVIDING AID TO GIVE MOUTH-TO-MOUTH
RESUSCITATION. GET MEDICAL ATTENTION. IF NECESSARY, CALL A POISON
CENTER OR PHYSICIAN. IF UNCONSCIOUS, PLACE IN RECOVERY POSITION AND
GET MEDICAL ATTENTION IMMEDIATELY. MAINTAIN AN OPEN AIRWAY. LOOSEN
TIGHT CLOTHING SUCH AS A COLLAR, TIE, BELT OR WAISTBAND.
SKIN CONTACT:
FLUSH CONTAMINATED SKIN WITH PLENTY OF WATER. REMOVE CONTAMINATED
CLOTHING AND SHOES. CONTINUE TO RINSE FOR AT LEAST 10 MINUTES. GET
MEDICAL ATTENTION. WASH CLOTHING BEFORE REUSE. CLEAN SHOES THOROUGHLY
BEFORE REUSE.
INGESTION:
GET MEDICAL ATTENTION IMMEDIATELY. CALL A POISON CENTER OR PHYSICIAN. WASH
OUT MOUTH WITH WATER. REMOVE DENTURES IF ANY. REMOVE VICTIM TO FRESH AIR
AND KEEP AT REST IN A POSITION COMFORTABLE FOR BREATHING. IF MATERIAL HAS
BEEN SWALLOWED AND THE EXPOSED PERSON IS CONSCIOUS, GIVE SMALL QUANTITIES
OF WATER TO DRINK. STOP IF THE EXPOSED PERSON FEELS SICK AS VOMITING MAY
BE DANGEROUS. ASPIRATION HAZARD IF SWALLOWED. CAN ENTER LUNGS AND CAUSE
DAMAGE. DO NOT INDUCE VOMITING. IF VOMITING OCCURS, THE HEAD SHOULD BE
KEPT LOW SO THAT VOMIT DOES NOT ENTER THE LUNGS. NEVER GIVE ANYTHING BY
MOUTH TO AN UNCONSCIOUS PERSON. IF UNCONSCIOUS, PLACE IN RECOVERY POSITION
AND GET MEDICAL ATTENTION IMMEDIATELY. MAINTAIN AN OPEN AIRWAY. LOOSEN
TIGHT CLOTHING SUCH AS A COLLAR, TIE, BELT OR WAISTBAND.
MOST IMPORTANT SYMPTOMS/EFFECTS, ACUTE AND DELAYED:
POTENTIAL ACUTE HEALTH EFFECTS:
EYE CONTACT: CAUSES SERIOUS EYE IRRITATION.
INHALATION:
CAN CAUSE CENTRAL NERVOUS SYSTEM (CNS) DEPRESSION. MAY CAUSE DROWSINESS
OR DIZZINESS. MAY CAUSE RESPIRATORY IRRITATION.
SKIN CONTACT: CAUSES SKIN IRRITATION.
INGESTION:
CAN CAUSE CENTRAL NERVOUS SYSTEM (CNS) DEPRESSION. MAY BE FATAL IF
SWALLOWED AND ENTERS AIRWAYS.
OVER-EXPOSURE SIGNS/SYMPTOMS:
EYE CONTACT:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
PAIN OR IRRITATION
WATERING
REDNESS
INHALATION:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
RESPIRATORY TRACT IRRITATION
COUGHING
NAUSEA OR VOMITING
HEADACHE
DROWSINESS/FATIGUE
DIZZINESS/VERTIGO
UNCONSCIOUSNESS
SKIN CONTACT:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
IRRITATION
REDNESS
INGESTION:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
NAUSEA OR VOMITING
INDICATION OF IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT NEEDED, IF
NECESSARY:
NOTES TO PHYSICIAN:
TREAT SYMPTOMATICALLY. CONTACT POISON TREATMENT SPECIALIST IMMEDIATELY IF
LARGE QUANTITIES HAVE BEEN INGESTED OR INHALED.
SPECIFIC TREATMENTS: NO SPECIFIC TREATMENT.
PROTECTION OF FIRST-AIDERS:
NO ACTION SHALL BE TAKEN INVOLVING ANY PERSONAL RISK OR WITHOUT SUITABLE
TRAINING. IF IT IS SUSPECTED THAT FUMES ARE STILL PRESENT, THE RESCUER
SHOULD WEAR AN APPROPRIATE MASK OR SELF-CONTAINED BREATHING APPARATUS.
IT MAY BE DANGEROUS TO THE PERSON PROVIDING AID TO GIVE MOUTH-TO-MOUTH
RESUSCITATION.
SEE TOXICOLOGICAL INFORMATION (SECTION 11)
| SECTION 5. FIRE-FIGHTING MEASURES | |
EXTINGUISHING MEDIA:
SUITABLE EXTINGUISHING MEDIA:
USE AN EXTINGUISHING AGENT SUITABLE FOR THE SURROUNDING FIRE.
UNSUITABLE EXTINGUISHING MEDIA: NONE KNOWN.
SPECIFIC HAZARDS ARISING FROM THE CHEMICAL:
EXTREMELY FLAMMABLE AEROSOL. IN A FIRE OR IF HEATED, A PRESSURE INCREASE
WILL OCCUR AND THE CONTAINER MAY BURST, WITH THE RISK OF A SUBSEQUENT
EXPLOSION. GAS MAY ACCUMULATE IN LOW OR CONFINED AREAS OR TRAVEL A
CONSIDERABLE DISTANCE TO A SOURCE OF IGNITION AND FLASH BACK, CAUSING
FIRE OR EXPLOSION. BURSTING AEROSOL CONTAINERS MAY BE PROPELLED FROM A
FIRE AT HIGH SPEED. RUNOFF TO SEWER MAY CREATE FIRE OR EXPLOSION HAZARD.
HAZARDOUS THERMAL DECOMPOSITION PRODUCTS:
DECOMPOSITION PRODUCTS MAY INCLUDE THE FOLLOWING MATERIALS:
CARBON DIOXIDE
CARBON MONOXIDE
METAL OXIDE/OXIDES
SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
PROMPTLY ISOLATE THE SCENE BY REMOVING ALL PERSONS FROM THE VICINITY OF
THE INCIDENT IF THERE IS A FIRE. NO ACTION SHALL BE TAKEN INVOLVING ANY
PERSONAL RISK OR WITHOUT SUITABLE TRAINING. MOVE CONTAINERS FROM FIRE AREA
IF THIS CAN BE DONE WITHOUT RISK. USE WATER SPRAY TO KEEP FIRE-EXPOSED
CONTAINERS COOL.
SPECIAL PROTECTIVE EQUIPMENT FOR FIRE-FIGHTERS:
FIRE-FIGHTERS SHOULD WEAR APPROPRIATE PROTECTIVE EQUIPMENT AND
SELF-CONTAINED BREATHING APPARATUS (SCBA) WITH A FULL FACE-PIECE
OPERATED IN POSITIVE PRESSURE MODE.
| SECTION 6. ACCIDENTAL RELEASE MEASURES | |
PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
FOR NON-EMERGENCY PERSONNEL:
NO ACTION SHALL BE TAKEN INVOLVING ANY PERSONAL RISK OR WITHOUT SUITABLE
TRAINING. EVACUATE SURROUNDING AREAS. KEEP UNNECESSARY AND UNPROTECTED
PERSONNEL FROM ENTERING. IN THE CASE OF AEROSOLS BEING RUPTURED, CARE
SHOULD BE TAKEN DUE TO THE RAPID ESCAPE OF THE PRESSURIZED CONTENTS AND
PROPELLANT. IF A LARGE NUMBER OF CONTAINERS ARE RUPTURED, TREAT AS A BULK
MATERIAL SPILLAGE ACCORDING TO THE INSTRUCTIONS IN THE CLEAN-UP SECTION.
DO NOT TOUCH OR WALK THROUGH SPILLED MATERIAL. SHUT OFF ALL IGNITION
SOURCES. NO FLARES, SMOKING OR FLAMES IN HAZARD AREA. AVOID BREATHING
VAPOR OR MIST. PROVIDE ADEQUATE VENTILATION. WEAR APPROPRIATE RESPIRATOR
WHEN VENTILATION IS INADEQUATE. PUT ON APPROPRIATE PERSONAL PROTECTIVE
EQUIPMENT.
FOR EMERGENCY RESPONDERS:
IF SPECIALIZED CLOTHING IS REQUIRED TO DEAL WITH THE SPILLAGE, TAKE NOTE
OF ANY INFORMATION IN SECTION 8 ON SUITABLE AND UNSUITABLE MATERIALS. SEE
ALSO THE INFORMATION IN "FOR NONEMERGENCY PERSONNEL".
ENVIRONMENTAL PRECAUTIONS:
AVOID DISPERSAL OF SPILLED MATERIAL AND RUNOFF AND CONTACT WITH SOIL,
WATERWAYS, DRAINS AND SEWERS. INFORM THE RELEVANT AUTHORITIES IF THE
PRODUCT HAS CAUSED ENVIRONMENTAL POLLUTION (SEWERS, WATERWAYS, SOIL
OR AIR).
METHODS AND MATERIALS FOR CONTAINMENT AND CLEANING UP:
SMALL SPILL:
STOP LEAK IF WITHOUT RISK. MOVE CONTAINERS FROM SPILL AREA. USE
SPARK-PROOF TOOLS AND EXPLOSION-PROOF EQUIPMENT. DILUTE WITH WATER
AND MOP UP IF WATER-SOLUBLE. ALTERNATIVELY, OR IF WATER-INSOLUBLE,
ABSORB WITH AN INERT DRY MATERIAL AND PLACE IN AN APPROPRIATE WASTE
DISPOSAL CONTAINER. DISPOSE OF VIA A LICENSED WASTE DISPOSAL CONTRACTOR.
LARGE SPILL:
STOP LEAK IF WITHOUT RISK. MOVE CONTAINERS FROM SPILL AREA. USE
SPARK-PROOF TOOLS AND EXPLOSION-PROOF EQUIPMENT. APPROACH RELEASE
FROM UPWIND. PREVENT ENTRY INTO SEWERS, WATER COURSES, BASEMENTS
OR CONFINED AREAS. WASH SPILLAGES INTO AN EFFLUENT TREATMENT PLANT
OR PROCEED AS FOLLOWS. CONTAIN AND COLLECT SPILLAGE WITH NON-COMBUSTIBLE,
ABSORBENT MATERIAL E.G. SAND, EARTH, VERMICULITE OR DIATOMACEOUS EARTH
AND PLACE IN CONTAINER FOR DISPOSAL ACCORDING TO LOCAL REGULATIONS
(SEE SECTION 13). DISPOSE OF VIA A LICENSED WASTE DISPOSAL CONTRACTOR.
CONTAMINATED ABSORBENT MATERIAL MAY POSE THE SAME HAZARD AS THE SPILLED
PRODUCT.
NOTE:
SEE SECTION 1 FOR EMERGENCY CONTACT INFORMATION AND SECTION 13 FOR WASTE
DISPOSAL.
| SECTION 7. HANDLING AND STORAGE | |
PRECAUTIONS FOR SAFE HANDLING:
PROTECTIVE MEASURES:
PUT ON APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT (SEE SECTION 8).
PRESSURIZED CONTAINER: PROTECT FROM SUNLIGHT AND DO NOT EXPOSE TO
TEMPERATURES EXCEEDING 50 DEG. C. DO NOT PIERCE OR BURN, EVEN AFTER
USE. AVOID EXPOSURE - OBTAIN SPECIAL INSTRUCTIONS BEFORE USE. DO NOT
HANDLE UNTIL ALL SAFETY PRECAUTIONS HAVE BEEN READ AND UNDERSTOOD. DO
NOT GET IN EYES OR ON SKIN OR CLOTHING. DO NOT BREATHE VAPOR OR MIST.
DO NOT SWALLOW. AVOID BREATHING GAS. USE ONLY WITH ADEQUATE VENTILATION.
WEAR APPROPRIATE RESPIRATOR WHEN VENTILATION IS INADEQUATE. STORE AND
USE AWAY FROM HEAT, SPARKS, OPEN FLAME OR ANY OTHER IGNITION SOURCE. USE
EXPLOSION-PROOF ELECTRICAL (VENTILATING, LIGHTING AND MATERIAL HANDLING)
EQUIPMENT. USE ONLY NON-SPARKING TOOLS. EMPTY CONTAINERS RETAIN PRODUCT
RESIDUE AND CAN BE HAZARDOUS.
ADVICE ON GENERAL OCCUPATIONAL HYGIENE:
EATING, DRINKING AND SMOKING SHOULD BE PROHIBITED IN AREAS WHERE THIS
MATERIAL IS HANDLED, STORED AND PROCESSED. WORKERS SHOULD WASH HANDS
AND FACE BEFORE EATING, DRINKING AND SMOKING. REMOVE CONTAMINATED CLOTHING
AND PROTECTIVE EQUIPMENT BEFORE ENTERING EATING AREAS. SEE ALSO SECTION 8
FOR ADDITIONAL INFORMATION ON HYGIENE MEASURES.
CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPATIBILITIES:
STORE IN ACCORDANCE WITH LOCAL REGULATIONS. STORE AWAY FROM DIRECT
SUNLIGHT IN A DRY, COOL AND WELL-VENTILATED AREA, AWAY FROM INCOMPATIBLE
MATERIALS (SEE SECTION 10) AND FOOD AND DRINK. PROTECT FROM SUNLIGHT.
STORE LOCKED UP. ELIMINATE ALL IGNITION SOURCES. USE APPROPRIATE
CONTAINMENT TO AVOID ENVIRONMENTAL CONTAMINATION.
| SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION | |
CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS (OSHA UNITED STATES):
INGREDIENT NAME EXPOSURE LIMITS
METHYL ACETATE ACGIH TLV (UNITED STATES, 3/2016).
TWA: 200 PPM 8 HOURS.
TWA: 606 MG/M3 8 HOURS.
STEL: 250 PPM 15 MINUTES.
STEL: 757 MG/M3 15 MINUTES.
NIOSH REL (UNITED STATES, 10/2013).
TWA: 200 PPM 10 HOURS.
TWA: 610 MG/M3 10 HOURS.
STEL: 250 PPM 15 MINUTES.
STEL: 760 MG/M3 15 MINUTES.
OSHA PEL (UNITED STATES, 6/2016).
TWA: 200 PPM 8 HOURS.
TWA: 610 MG/M3 8 HOURS.
METHYL ETHYL KETONE ACGIH TLV (UNITED STATES, 3/2016).
TWA: 200 PPM 8 HOURS.
TWA: 590 MG/M3 8 HOURS.
STEL: 300 PPM 15 MINUTES.
STEL: 885 MG/M3 15 MINUTES.
NIOSH REL (UNITED STATES, 10/2013).
TWA: 200 PPM 10 HOURS.
TWA: 590 MG/M3 10 HOURS.
STEL: 300 PPM 15 MINUTES.
STEL: 885 MG/M3 15 MINUTES.
OSHA PEL (UNITED STATES, 6/2016).
TWA: 200 PPM 8 HOURS.
TWA: 590 MG/M3 8 HOURS.
PROPANE NIOSH REL (UNITED STATES, 10/2013).
TWA: 1000 PPM 10 HOURS.
TWA: 1800 MG/M3 10 HOURS.
OSHA PEL (UNITED STATES, 6/2016).
TWA: 1000 PPM 8 HOURS.
TWA: 1800 MG/M3 8 HOURS.
BUTANE NIOSH REL (UNITED STATES, 10/2013).
TWA: 800 PPM 10 HOURS.
TWA: 1900 MG/M3 10 HOURS.
ACGIH TLV (UNITED STATES, 3/2016).
STEL: 1000 PPM 15 MINUTES.
1-METHOXY-2-PROPANOL ACETATE AIHA WEEL (UNITED STATES, 10/2011).
TWA: 50 PPM 8 HOURS.
XYLENE ACGIH TLV (UNITED STATES, 3/2016).
TWA: 100 PPM 8 HOURS.
TWA: 434 MG/M3 8 HOURS.
STEL: 150 PPM 15 MINUTES.
STEL: 651 MG/M3 15 MINUTES.
OSHA PEL (UNITED STATES, 6/2016).
TWA: 100 PPM 8 HOURS.
TWA: 435 MG/M3 8 HOURS.
TITANIUM DIOXIDE ACGIH TLV (UNITED STATES, 3/2016).
TWA: 10 MG/M3 8 HOURS.
OSHA PEL (UNITED STATES, 6/2016).
TWA: 15 MG/M3 8 HOURS.
FORM: TOTAL DUST
ACETONE ACGIH TLV (UNITED STATES, 3/2016).
TWA: 250 PPM 8 HOURS.
STEL: 500 PPM 15 MINUTES.
NIOSH REL (UNITED STATES, 10/2013).
TWA: 250 PPM 10 HOURS.
TWA: 590 MG/M3 10 HOURS.
OSHA PEL (UNITED STATES, 6/2016).
TWA: 1000 PPM 8 HOURS.
TWA: 2400 MG/M3 8 HOURS.
ETHYLBENZENE ACGIH TLV (UNITED STATES, 3/2016).
TWA: 20 PPM 8 HOURS.
NIOSH REL (UNITED STATES, 10/2013).
TWA: 100 PPM 10 HOURS.
TWA: 435 MG/M3 10 HOURS.
STEL: 125 PPM 15 MINUTES.
STEL: 545 MG/M3 15 MINUTES.
OSHA PEL (UNITED STATES, 6/2016).
TWA: 100 PPM 8 HOURS.
TWA: 435 MG/M3 8 HOURS.
OCCUPATIONAL EXPOSURE LIMITS (CANADA):
INGREDIENT NAME EXPOSURE LIMITS
METHYL ACETATE CA ALBERTA PROVINCIAL (CANADA, 4/2009).
8 HRS OEL: 606 MG/M3 8 HOURS.
15 MIN OEL: 757 MG/M3 15 MINUTES.
15 MIN OEL: 250 PPM 15 MINUTES.
8 HRS OEL: 200 PPM 8 HOURS.
CA BRITISH COLUMBIA PROVINCIAL (CANADA, 5/2015).
TWA: 200 PPM 8 HOURS.
STEL: 250 PPM 15 MINUTES.
CA ONTARIO PROVINCIAL (CANADA, 7/2015).
TWA: 200 PPM 8 HOURS.
STEL: 250 PPM 15 MINUTES.
CA QUEBEC PROVINCIAL (CANADA, 1/2014).
TWAEV: 200 PPM 8 HOURS.
TWAEV: 606 MG/M3 8 HOURS.
STEV: 250 PPM 15 MINUTES.
STEV: 757 MG/M3 15 MINUTES.
CA SASKATCHEWAN PROVINCIAL (CANADA,7/2013).
STEL: 250 PPM 15 MINUTES.
TWA: 200 PPM 8 HOURS.
METHYL ETHYL KETONE CA ALBERTA PROVINCIAL (CANADA, 4/2009).
15 MIN OEL: 300 PPM 15 MINUTES.
8 HRS OEL: 200 PPM 8 HOURS.
8 HRS OEL: 590 MG/M3 8 HOURS.
15 MIN OEL: 885 MG/M3 15 MINUTES.
CA BRITISH COLUMBIA PROVINCIAL (CANADA, 5/2015).
TWA: 50 PPM 8 HOURS.
STEL: 100 PPM 15 MINUTES.
CA ONTARIO PROVINCIAL (CANADA, 7/2015).
TWA: 200 PPM 8 HOURS.
STEL: 300 PPM 15 MINUTES.
CA QUEBEC PROVINCIAL (CANADA, 1/2014).
TWAEV: 50 PPM 8 HOURS.
TWAEV: 150 MG/M3 8 HOURS.
STEV: 100 PPM 15 MINUTES.
STEV: 300 MG/M3 15 MINUTES.
CA SASKATCHEWAN PROVINCIAL (CANADA, 7/2013).
STEL: 300 PPM 15 MINUTES.
TWA: 200 PPM 8 HOURS.
PROPANE CA ALBERTA PROVINCIAL (CANADA, 4/2009).
8 HRS OEL: 1000 PPM 8 HOURS.
CA BRITISH COLUMBIA PROVINCIAL (CANADA, 5/2015).
TWA: 1000 PPM 8 HOURS.
CA QUEBEC PROVINCIAL (CANADA, 1/2014).
TWAEV: 1000 PPM 8 HOURS.
TWAEV: 1800 MG/M3 8 HOURS.
CA ONTARIO PROVINCIAL (CANADA, 7/2015).
TWA: 1000 PPM 8 HOURS.
CA SASKATCHEWAN PROVINCIAL (CANADA, 7/2013).
STEL: 1250 PPM 15 MINUTES.
TWA: 1000 PPM 8 HOURS.
OCCUPATIONAL EXPOSURE LIMITS (MEXICO):
INGREDIENT NAME EXPOSURE LIMITS
METHYL ACETATE NOM-010-STPS (MEXICO, 4/2016).
LMPE-PPT: 200 PPM 8 HOURS.
LMPE-CT: 250 PPM 15 MINUTES.
METHYL ETHYL KETONE NOM-010-STPS (MEXICO, 4/2016).
LMPE-PPT: 200 PPM 8 HOURS.
LMPE-CT: 300 PPM 15 MINUTES.
PROPANE NOM-010-STPS (MEXICO, 4/2016).
LMPE-PPT: 1000 PPM 8 HOURS.
BUTANE NOM-010-STPS (MEXICO, 4/2016).
LMPE-PPT: 1000 PPM 8 HOURS.
XYLENE NOM-010-STPS (MEXICO, 4/2016).
LMPE-CT: 150 PPM 15 MINUTES.
LMPE-PPT: 100 PPM 8 HOURS.
ACETONE NOM-010-STPS (MEXICO, 4/2016).
LMPE-PPT: 500 PPM 8 HOURS.
LMPE-CT: 750 PPM 15 MINUTES.
APPROPRIATE ENGINEERING CONTROLS:
USE ONLY WITH ADEQUATE VENTILATION. USE PROCESS ENCLOSURES, LOCAL
EXHAUST VENTILATION OR OTHER ENGINEERING CONTROLS TO KEEP WORKER
EXPOSURE TO AIRBORNE CONTAMINANTS BELOW ANY RECOMMENDED OR STATUTORY
LIMITS. THE ENGINEERING CONTROLS ALSO NEED TO KEEP GAS, VAPOR OR DUST
CONCENTRATIONS BELOW ANY LOWER EXPLOSIVE LIMITS. USE EXPLOSION-PROOF
VENTILATION EQUIPMENT.
ENVIRONMENTAL EXPOSURE CONTROLS:
EMISSIONS FROM VENTILATION OR WORK PROCESS EQUIPMENT SHOULD BE CHECKED
TO ENSURE THEY COMPLY WITH THE REQUIREMENTS OF ENVIRONMENTAL PROTECTION
LEGISLATION. IN SOME CASES, FUME SCRUBBERS, FILTERS OR ENGINEERING
MODIFICATIONS TO THE PROCESS EQUIPMENT WILL BE NECESSARY TO REDUCE
EMISSIONS TO ACCEPTABLE LEVELS.
INDIVIDUAL PROTECTION MEASURES:
HYGIENE MEASURES:
WASH HANDS, FOREARMS AND FACE THOROUGHLY AFTER HANDLING CHEMICAL
PRODUCTS, BEFORE EATING, SMOKING AND USING THE LAVATORY AND AT THE
END OF THE WORKING PERIOD. APPROPRIATE TECHNIQUES SHOULD BE USED TO
REMOVE POTENTIALLY CONTAMINATED CLOTHING. WASH CONTAMINATED CLOTHING
BEFORE REUSING. ENSURE THAT EYEWASH STATIONS AND SAFETY SHOWERS ARE
CLOSE TO THE WORKSTATION LOCATION.
EYE/FACE PROTECTION:
SAFETY EYEWEAR COMPLYING WITH AN APPROVED STANDARD SHOULD BE USED WHEN
A RISK ASSESSMENT INDICATES THIS IS NECESSARY TO AVOID EXPOSURE TO LIQUID
SPLASHES, MISTS, GASES OR DUSTS.
IF CONTACT IS POSSIBLE, THE FOLLOWING PROTECTION SHOULD BE WORN, UNLESS
THE ASSESSMENT INDICATES A HIGHER DEGREE OF PROTECTION:
CHEMICAL SPLASH GOGGLES.
SKIN PROTECTION:
HAND PROTECTION:
CHEMICAL-RESISTANT, IMPERVIOUS GLOVES COMPLYING WITH AN APPROVED STANDARD
SHOULD BE WORN AT ALL TIMES WHEN HANDLING CHEMICAL PRODUCTS IF A RISK
ASSESSMENT INDICATES THIS IS NECESSARY. CONSIDERING THE PARAMETERS
SPECIFIED BY THE GLOVE MANUFACTURER, CHECK DURING USE THAT THE GLOVES
ARE STILL RETAINING THEIR PROTECTIVE PROPERTIES. IT SHOULD BE NOTED THAT
THE TIME TO BREAKTHROUGH FOR ANY GLOVE MATERIAL MAY BE DIFFERENT FOR
DIFFERENT GLOVE MANUFACTURERS. IN THE CASE OF MIXTURES, CONSISTING OF
SEVERAL SUBSTANCES, THE PROTECTION TIME OF THE GLOVES CANNOT BE ACCURATELY
ESTIMATED.
BODY PROTECTION:
PERSONAL PROTECTIVE EQUIPMENT FOR THE BODY SHOULD BE SELECTED BASED ON THE
TASK BEING PERFORMED AND THE RISKS INVOLVED AND SHOULD BE APPROVED BY A
SPECIALIST BEFORE HANDLING THIS PRODUCT. WHEN THERE IS A RISK OF IGNITION
FROM STATIC ELECTRICITY, WEAR ANTISTATIC PROTECTIVE CLOTHING. FOR THE
GREATEST PROTECTION FROM STATIC DISCHARGES, CLOTHING SHOULD INCLUDE
ANTI-STATIC OVERALLS, BOOTS AND GLOVES.
OTHER SKIN PROTECTION:
APPROPRIATE FOOTWEAR AND ANY ADDITIONAL SKIN PROTECTION MEASURES SHOULD
BE SELECTED BASED ON THE TASK BEING PERFORMED AND THE RISKS INVOLVED AND
SHOULD BE APPROVED BY A SPECIALIST BEFORE HANDLING THIS PRODUCT.
RESPIRATORY PROTECTION:
BASED ON THE HAZARD AND POTENTIAL FOR EXPOSURE, SELECT A RESPIRATOR THAT
MEETS THE APPROPRIATE STANDARD OR CERTIFICATION. RESPIRATORS MUST BE USED
ACCORDING TO A RESPIRATORY PROTECTION PROGRAM TO ENSURE PROPER FITTING,
TRAINING, AND OTHER IMPORTANT ASPECTS OF USE.
| SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES | |
APPEARANCE:
PHYSICAL STATE: LIQUID.
COLOR: NOT AVAILABLE.
ODOR: NOT AVAILABLE.
ODOR THRESHOLD: NOT AVAILABLE.
PH: NOT AVAILABLE.
MELTING POINT: NOT AVAILABLE.
BOILING POINT: NOT AVAILABLE.
FLASH POINT:
CLOSED CUP: -29 DEG. C (-20.2 DEG. F) [PENSKY-MARTENS CLOSED CUP]
EVAPORATION RATE: 5.6 (BUTYL ACETATE = 1)
FLAMMABILITY (SOLID, GAS): NOT AVAILABLE.
LOWER AND UPPER EXPLOSIVE (FLAMMABLE) LIMITS:
LOWER: 1%
UPPER: 16%
VAPOR PRESSURE: 101.3 KPA (760 MM HG) [AT 20 DEG. C]
VAPOR DENSITY: 1.55 [AIR = 1]
RELATIVE DENSITY: 0.8
SOLUBILITY: NOT AVAILABLE.
PARTITION COEFFICIENT N-OCTANOL/WATER: NOT AVAILABLE.
AUTO-IGNITION TEMPERATURE: NOT AVAILABLE.
DECOMPOSITION TEMPERATURE: NOT AVAILABLE.
VISCOSITY:
KINEMATIC (40 DEG. C (104 DEG. F)): <0.205 CM2/S (<20.5 CST)
MOLECULAR WEIGHT: NOT APPLICABLE.
AEROSOL PRODUCT:
TYPE OF AEROSOL: SPRAY
HEAT OF COMBUSTION: 33.9 KJ/G
| SECTION 10. STABILITY AND REACTIVITY | |
REACTIVITY:
NO SPECIFIC TEST DATA RELATED TO REACTIVITY AVAILABLE FOR THIS PRODUCT OR
ITS INGREDIENTS.
CHEMICAL STABILITY: THE PRODUCT IS STABLE.
POSSIBILITY OF HAZARDOUS REACTIONS:
UNDER NORMAL CONDITIONS OF STORAGE AND USE, HAZARDOUS REACTIONS WILL NOT
OCCUR.
CONDITIONS TO AVOID:
AVOID ALL POSSIBLE SOURCES OF IGNITION (SPARK OR FLAME).
INCOMPATIBLE MATERIALS: NO SPECIFIC DATA.
HAZARDOUS DECOMPOSITION PRODUCTS:
UNDER NORMAL CONDITIONS OF STORAGE AND USE, HAZARDOUS DECOMPOSITION
PRODUCTS SHOULD NOT BE PRODUCED.
| SECTION 11. TOXICOLOGICAL INFORMATION | |
INFORMATION ON TOXICOLOGICAL EFFECTS:
ACUTE TOXICITY:
PRODUCT/INGREDIENT RESULT SPECIES DOSE EXPOSURE
NAME
METHYL ACETATE LD50 DERMAL RABBIT >5 G/KG
LD50 ORAL RAT >5 G/KG
METHYL ETHYL LD50 DERMAL RABBIT 6480 MG/KG
KETONE LD50 ORAL RAT 2737 MG/KG
BUTANE LC50 INHALATION RAT 658000 MG/M3 4 HOURS
VAPOR
1-METHOXY-2- LD50 DERMAL RABBIT >5 G/KG
PROPANOL LD50 ORAL RAT 8532 MG/KG
ACETATE
XYLENE LC50 INHALATION GAS. RAT 5000 PPM 4 HOURS
LD50 ORAL RAT 4300 MG/KG
ACETONE LD50 ORAL RAT 5800 MG/KG
ETHYLBENZENE LD50 DERMAL RABBIT >5000 MG/KG
LD50 ORAL RAT 3500 MG/KG
IRRITATION/CORROSION:
PRODUCT/ RESULT SPECIES SCORE EXPOSURE OBSERVATION
INGREDIENT
NAME
METHYL EYES: RABBIT 24 HOURS 100
ACETATE MODERATE MILLIGRAMS
IRRITANT
SKIN: RABBIT 24 HOURS 500
MILD IRRITANT MILLIGRAMS
SKIN: RABBIT 24 HOURS 20
MODERATE MILLIGRAMS
IRRITANT
METHYL SKIN: RABBIT 24 HOURS 14
ETHYL MILD IRRITANT MILLIGRAMS
KETONE
SKIN: RABBIT 24 HOURS 500
MODERATE MILLIGRAMS
IRRITANT
XYLENE EYES: RABBIT 87 MILLIGRAMS
MILD IRRITANT
EYES: RABBIT 24 HOURS 5
SEVERE IRRITANT MILLIGRAMS
SKIN: RAT 8 HOURS 60
MILD IRRITANT MICROLITERS
SKIN: RABBIT 24 HOURS 500
MODERATE MILLIGRAMS
IRRITANT
SKIN: RABBIT 100 PERCENT
MODERATE
IRRITANT
TITANIUM SKIN: HUMAN 72 HOURS 300
DIOXIDE MILD IRRITANT MICROGRAMS
INTERMITTENT
ACETONE EYES: HUMAN 186300 PARTS
MILD IRRITANT PER MILLION
EYES: RABBIT 10 MICROLITERS
MILD IRRITANT
EYES: RABBIT 24 HOURS 20
MODERATE MILLIGRAMS
IRRITANT
EYES: RABBIT 20 MILLIGRAMS
SEVERE IRRITANT
SKIN: RABBIT 24 HOURS 500
MILD IRRITANT MILLIGRAMS
SKIN: RABBIT 395 MILLIGRAMS
MILD IRRITANT
ETHYL- EYES: RABBIT 500 MILLIGRAMS
BENZENE SEVERE IRRITANT
SKIN: RABBIT 24 HOURS 15
MILD IRRITANT MILLIGRAMS
SENSITIZATION: NOT AVAILABLE.
MUTAGENICITY: NOT AVAILABLE.
CARCINOGENICITY: NOT AVAILABLE.
CLASSIFICATION:
PRODUCT/INGREDIENT NAME OSHA IARC NTP
XYLENE 3
TITANIUM DIOXIDE 2B
ETHYLBENZENE 2B
REPRODUCTIVE TOXICITY: NOT AVAILABLE.
TERATOGENICITY: NOT AVAILABLE.
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE):
NAME CATEGORY ROUTE OF TARGET ORGANS
EXPOSURE
METHYL ACETATE CATEGORY 3 NOT APPLICABLE. NARCOTIC EFFECTS
METHYL ETHYL KETONE CATEGORY 3 NOT APPLICABLE. RESPIRATORY TRACT
IRRITATION AND
NARCOTIC EFFECTS
PROPANE CATEGORY 3 NOT APPLICABLE. RESPIRATORY TRACT
IRRITATION AND
NARCOTIC EFFECTS
BUTANE CATEGORY 3 NOT APPLICABLE. RESPIRATORY TRACT
IRRITATION AND
NARCOTIC EFFECTS
XYLENE CATEGORY 3 NOT APPLICABLE. RESPIRATORY TRACT
IRRITATION AND
NARCOTIC EFFECTS
ACETONE CATEGORY 3 NOT APPLICABLE. RESPIRATORY TRACT
IRRITATION AND
NARCOTIC EFFECTS
ETHYLBENZENE CATEGORY 3 NOT APPLICABLE. RESPIRATORY TRACT
IRRITATION AND
NARCOTIC EFFECTS
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE):
NAME CATEGORY ROUTE OF TARGET ORGANS
EXPOSURE
METHYL ETHYL KETONE CATEGORY 2 NOT DETERMINED NOT DETERMINED
PROPANE CATEGORY 2 NOT DETERMINED NOT DETERMINED
BUTANE CATEGORY 2 NOT DETERMINED NOT DETERMINED
XYLENE CATEGORY 2 NOT DETERMINED NOT DETERMINED
ACETONE CATEGORY 2 NOT DETERMINED NOT DETERMINED
ETHYLBENZENE CATEGORY 2 NOT DETERMINED NOT DETERMINED
ASPIRATION HAZARD:
NAME RESULT
PROPANE ASPIRATION HAZARD - CATEGORY 1
BUTANE ASPIRATION HAZARD - CATEGORY 1
XYLENE ASPIRATION HAZARD - CATEGORY 1
ETHYLBENZENE ASPIRATION HAZARD - CATEGORY 1
INFORMATION ON THE LIKELYROUTES OF EXPOSURE: NOT AVAILABLE.
POTENTIAL ACUTE HEALTH EFFECTS:
EYE CONTACT: CAUSES SERIOUS EYE IRRITATION.
INHALATION:
CAN CAUSE CENTRAL NERVOUS SYSTEM (CNS) DEPRESSION. MAY CAUSE DROWSINESS
OR DIZZINESS. MAY CAUSE RESPIRATORY IRRITATION.
SKIN CONTACT: CAUSES SKIN IRRITATION.
INGESTION:
CAN CAUSE CENTRAL NERVOUS SYSTEM (CNS) DEPRESSION. MAY BE FATAL IF
SWALLOWED AND ENTERS AIRWAYS.
SYMPTOMS RELATED TO THE PHYSICAL, CHEMICAL AND TOXICOLOGICAL
CHARACTERISTICS:
EYE CONTACT:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
PAIN OR IRRITATION
WATERING
REDNESS
INHALATION:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
RESPIRATORY TRACT IRRITATION
COUGHING
NAUSEA OR VOMITING
HEADACHE
DROWSINESS/FATIGUE
DIZZINESS/VERTIGO
UNCONSCIOUSNESS
SKIN CONTACT:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
IRRITATION
REDNESS
INGESTION:
ADVERSE SYMPTOMS MAY INCLUDE THE FOLLOWING:
NAUSEA OR VOMITING
DELAYED AND IMMEDIATE EFFECTS AND ALSO CHRONIC EFFECTS FROM SHORT AND LONG
TERM EXPOSURE:
SHORT TERM EXPOSURE:
POTENTIAL IMMEDIATE EFFECTS: NOT AVAILABLE.
POTENTIAL DELAYED EFFECTS: NOT AVAILABLE.
LONG TERM EXPOSURE:
POTENTIAL IMMEDIATE EFFECTS: NOT AVAILABLE.
POTENTIAL DELAYED EFFECTS: NOT AVAILABLE.
POTENTIAL CHRONIC HEALTH EFFECTS: NOT AVAILABLE.
GENERAL:
MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.
CARCINOGENICITY:
SUSPECTED OF CAUSING CANCER. RISK OF CANCER DEPENDS ON DURATION AND LEVEL
OF EXPOSURE.
MUTAGENICITY: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
TERATOGENICITY: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
DEVELOPMENTAL EFFECTS: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
FERTILITY EFFECTS: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
NUMERICAL MEASURES OF TOXICITY:
ACUTE TOXICITY ESTIMATES:
ROUTE ATE VALUE
ORAL 10516.3 MG/KG
INHALATION (GASES) 122946.4 PPM
| SECTION 12. ECOLOGICAL INFORMATION | |
TOXICITY:
PRODUCT/INGREDIENT RESULT SPECIES EXPOSURE
NAME
METHYL ACETATE ACUTE LC50: FISH - PIMEPHALES 96 HOURS
320000 (MICRO)G/L PROMELAS
FRESH WATER
METHYL ETHYL ACUTE EC50: ALGAE - SKELETONEMA 96 HOURS
KETONE >500000 (MICRO)G/L COSTATUM
MARINE WATER
ACUTE EC50: DAPHNIA - DAPHNIA 48 HOURS
5091000 (MICRO)G/L MAGNA - LARVAE
FRESH WATER
ACUTE LC50: FISH - PIMEPHALES 96 HOURS
3220000 (MICRO)G/L PROMELAS
FRESH WATER
XYLENE ACUTE LC50: CRUSTACEANS - 48 HOURS
8500 (MICRO)G/L PALAEMONETES PUGIO
MARINE WATER
ACUTE LC50: FISH - PIMEPHALES 96 HOURS
13400 (MICRO)G/L PROMELAS
FRESH WATER
TITANIUM DIOXIDE ACUTE LC50: FISH - FUNDULUS 96 HOURS
>1000000 (MICRO)G/L HETEROCLITUS
MARINE WATER
ACETONE ACUTE EC50: ALGAE - SELENASTRUM SP. 96 HOURS
7200000 (MICRO)G/L
FRESH WATER
ACUTE LC50: CRUSTACEANS - GAMMARUS 48 HOURS
6000000 (MICRO)G/L PULEX
FRESH WATER
ACUTE LC50: DAPHNIA - DAPHNIA MAGNA 48 HOURS
6900 MG/L
FRESH WATER
ACUTE LC50: FISH - POECILIA 96 HOURS
5600 PPM RETICULATA
FRESH WATER
CHRONIC NOEC: ALGAE - ULVA PERTUSA 96 HOURS
4.95 MG/L
MARINE WATER
CHRONIC NOEC: CRUSTACEANS - 21 DAYS
0.016 ML/L DAPHNIIDAE
FRESH WATER
CHRONIC NOEC: DAPHNIA - DAPHNIA 21 DAYS
0.1 ML/L MAGNA - NEONATE
FRESH WATER
ETHYLBENZENE ACUTE EC50: ALGAE - 72 HOURS
4600 (MICRO)G/L PSEUDOKIRCHNERIELLA
FRESH WATER SUBCAPITATA
ACUTE EC50: ALGAE - 96 HOURS
3600 (MICRO)G/L PSEUDOKIRCHNERIELLA
FRESH WATER SUBCAPITATA
ACUTE EC50: CRUSTACEANS - ARTEMIA 48 HOURS
6530 (MICRO)G/L SP. - NAUPLII
FRESH WATER
ACUTE EC50: DAPHNIA - DAPHNIA 48 HOURS
2930 (MICRO)G/L MAGNA - NEONATE
FRESH WATER
ACUTE LC50: FISH - ONCORHYNCHUS 96 HOURS
4200 (MICRO)G/L MYKISS
FRESH WATER
PERSISTENCE AND DEGRADABILITY:
PRODUCT/INGREDIENT NAME AQUATIC HALF-LIFE PHOTOLYSIS BIODEGRADABILITY
METHYL ETHYL KETONE READILY
XYLENE READILY
ACETONE READILY
ETHYLBENZENE READILY
BIOACCUMULATIVE POTENTIAL:
PRODUCT/INGREDIENT NAME LOGPOW BCF POTENTIAL
XYLENE 8.1 TO 25.9 LOW
MOBILITY IN SOIL:
SOIL/WATER PARTITION COEFFICIENT (KOC): NOT AVAILABLE.
OTHER ADVERSE EFFECTS: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
| SECTION 13. DISPOSAL CONSIDERATIONS | |
DISPOSAL METHODS:
THE GENERATION OF WASTE SHOULD BE AVOIDED OR MINIMIZED WHEREVER POSSIBLE.
DISPOSAL OF THIS PRODUCT, SOLUTIONS AND ANY BY-PRODUCTS SHOULD AT ALL
TIMES COMPLY WITH THE REQUIREMENTS OF ENVIRONMENTAL PROTECTION AND WASTE
DISPOSAL LEGISLATION AND ANY REGIONAL LOCAL AUTHORITY REQUIREMENTS.
DISPOSE OF SURPLUS AND NON-RECYCLABLE PRODUCTS VIA A LICENSED WASTE
DISPOSAL CONTRACTOR. WASTE SHOULD NOT BE DISPOSED OF UNTREATED TO THE
SEWER UNLESS FULLY COMPLIANT WITH THE REQUIREMENTS OF ALL AUTHORITIES
WITH JURISDICTION. WASTE PACKAGING SHOULD BE RECYCLED. INCINERATION OR
LANDFILL SHOULD ONLY BE CONSIDERED WHEN RECYCLING IS NOT FEASIBLE. THIS
MATERIAL AND ITS CONTAINER MUST BE DISPOSED OF IN A SAFE WAY. EMPTY
CONTAINERS OR LINERS MAY RETAIN SOME PRODUCT RESIDUES. DO NOT PUNCTURE
OR INCINERATE CONTAINER.
| SECTION 14. TRANSPORT INFORMATION | |
DOT TDG MEXICO
CLASSIFICATION CLASSIFICATION CLASSIFICATION
UN NUMBER UN1950 UN1950 UN1950
UN PROPER SHIPPING AEROSOLS AEROSOLS AEROSOLS
NAME
TRANSPORT HAZARD 2.1 2.1 2.1
CLASS(ES) FLAMMABLE GAS, CLASS 2.1, CLASS 2.1,
CLASS/DIVISION 2.1 FLAMMABLE GASES FLAMMABLE GASES
PACKING GROUP
ENVIRONMENTAL NO. NO. NO.
HAZARDS
ADDITIONAL PRODUCT
INFORMATION CLASSIFIED
AS PER THE
FOLLOWING
SECTIONS
OF THE
TRANSPORTATION
OF DANGEROUS
GOODS
REGULATIONS: 2.
13-2.17
(CLASS 2).
ERG NO. ERG NO. ERG NO.
126 126 126
IATA IMDG
UN NUMBER UN1950 UN1950
UN PROPER SHIPPING NAME AEROSOLS, AEROSOLS
FLAMMABLE
TRANSPORT HAZARD CLASS(ES) 2.1 2.1
CLASS 2.1, CLASS 2.1 -
FLAMMABLE GASES FLAMMABLE GASES
PACKING GROUP
ENVIRONMENTAL HAZARDS NO. NO.
ADDITIONAL INFORMATION EMERGENCY SCHEDULES (EMS):
F-D, S-U
SPECIAL PRECAUTIONS FOR USER:
MULTI-MODAL SHIPPING DESCRIPTIONS ARE PROVIDED FOR INFORMATIONAL
PURPOSES AND DO NOT CONSIDER CONTAINER SIZES. THE PRESENCE OF A
SHIPPING DESCRIPTION FOR A PARTICULAR MODE OF TRANSPORT (SEA, AIR, ETC.),
DOES NOT INDICATE THAT THE PRODUCT IS PACKAGED SUITABLY FOR THAT MODE OF
TRANSPORT. ALL PACKAGING MUST BE REVIEWED FOR SUITABILITY PRIOR TO
SHIPMENT, AND COMPLIANCE WITH THE APPLICABLE REGULATIONS IS THE SOLE
RESPONSIBILITY OF THE PERSON OFFERING THE PRODUCT FOR TRANSPORT. PEOPLE
LOADING AND UNLOADING DANGEROUS GOODS MUST BE TRAINED ON ALL OF THE RISKS
DERIVING FROM THE SUBSTANCES AND ON ALL ACTIONS IN CASE OF EMERGENCY
SITUATIONS.
TRANSPORT IN BULK ACCORDING TO ANNEX II OF MARPOL AND THE IBC CODE:
NOT AVAILABLE.
PROPER SHIPPING NAME: NOT AVAILABLE.
SHIP TYPE: NOT AVAILABLE.
POLLUTION CATEGORY: NOT AVAILABLE.
| SECTION 15. REGULATORY INFORMATION | |
SARA 313:
SARA 313 (40 CFR 372.45) SUPPLIER NOTIFICATION CAN BE FOUND ON THE
ENVIRONMENTAL DATA SHEET.
CALIFORNIA PROP. 65:
WARNING:
THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE
CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
| SECTION 16. OTHER INFORMATION | |
HAZARDOUS MATERIAL INFORMATION SYSTEM (U.S.A.):
HEALTH 2*
FLAMMABILITY 4
PHYSICAL HAZARDS 0
THE CUSTOMER IS RESPONSIBLE FOR DETERMINING THE PPE CODE FOR THIS
MATERIAL.
CAUTION:
HMIS(R*) RATINGS ARE BASED ON A 0-4 RATING SCALE, WITH 0 REPRESENTING
MINIMAL HAZARDS OR RISKS, AND 4 REPRESENTING SIGNIFICANT HAZARDS OR RISKS
ALTHOUGH HMIS(R*) RATINGS ARE NOT REQUIRED ON SDSS UNDER 29 CFR 1910.
1200, THE PREPARER MAY CHOOSE TO PROVIDE THEM. HMIS(R*) RATINGS ARE TO
BE USED WITH A FULLY IMPLEMENTED HMIS(R*) PROGRAM. HMIS(R*) IS A
REGISTERED MARK OF THE NATIONAL PAINT & COATINGS ASSOCIATION (NPCA).
HMIS(R*) MATERIALS MAY BE PURCHASED EXCLUSIVELY FROM J. J. KELLER
(800) 327-6868.
PROCEDURE USED TO DERIVE THE CLASSIFICATION:
CLASSIFICATION JUSTIFICATION
FLAMMABLE AEROSOLS - CATEGORY 1 ON BASIS OF TEST DATA
GASES UNDER PRESSURE - COMPRESSED GAS CALCULATION METHOD
SKIN CORROSION/IRRITATION - CATEGORY 2 CALCULATION METHOD
SERIOUS EYE DAMAGE/ EYE IRRITATION - CATEGORY 2A CALCULATION METHOD
CARCINOGENICITY - CATEGORY 2 CALCULATION METHOD
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) CALCULATION METHOD
(RESPIRATORY TRACT IRRITATION) - CATEGORY 3
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) CALCULATION METHOD
(NARCOTIC EFFECTS) - CATEGORY 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) CALCULATION METHOD
- CATEGORY 2
ASPIRATION HAZARD - CATEGORY 1 CALCULATION METHOD
HISTORY:
DATE OF PRINTING: 5/18/2017
DATE OF ISSUE/DATE OF REVISION: 5/18/2017
DATE OF PREVIOUS ISSUE: 4/17/2017
VERSION: 8
KEY TO ABBREVIATIONS:
ATE: ACUTE TOXICITY ESTIMATE
BCF: BIOCONCENTRATION FACTOR
GHS:
GLOBALLY HARMONIZED SYSTEM OF CLASSIFICATION AND LABELLING OF CHEMICALS
IATA: INTERNATIONAL AIR TRANSPORT ASSOCIATION
IBC: INTERMEDIATE BULK CONTAINER
IMDG: INTERNATIONAL MARITIME DANGEROUS GOODS
LOGPOW: LOGARITHM OF THE OCTANOL/WATER PARTITION COEFFICIENT
MARPOL:
INTERNATIONAL CONVENTION FOR THE PREVENTION OF POLLUTION FROM SHIPS, 1973
AS MODIFIED BY THE PROTOCOL OF 1978. ("MARPOL" = MARINE POLLUTION)
UN: UNITED NATIONS
NOTICE TO READER:
IT IS RECOMMENDED THAT EACH CUSTOMER OR RECIPIENT OF THIS SAFETY DATA
SHEET (SDS) STUDY IT CAREFULLY AND CONSULT RESOURCES, AS NECESSARY OR
APPROPRIATE, TO BECOME AWARE OF AND UNDERSTAND THE DATA CONTAINED IN
THIS SDS AND ANY HAZARDS ASSOCIATED WITH THE PRODUCT. THIS INFORMATION
IS PROVIDED IN GOOD FAITH AND BELIEVED TO BE ACCURATE AS OF THE EFFECTIVE
DATE HEREIN. HOWEVER, NO WARRANTY, EXPRESS OR IMPLIED, IS GIVEN. THE
INFORMATION PRESENTED HERE APPLIES ONLY TO THE PRODUCT AS SHIPPED. THE
ADDITION OF ANY MATERIAL CAN CHANGE THE COMPOSITION, HAZARDS AND RISKS
OF THE PRODUCT. PRODUCTS SHALL NOT BE REPACKAGED, MODIFIED, OR TINTED
EXCEPT AS SPECIFICALLY INSTRUCTED BY SHERWIN-WILLIAMS, INCLUDING BUT
NOT LIMITED TO THE INCORPORATION OF NON SHERWIN-WILLIAMS PRODUCTS OR
THE USE OR ADDITION OF PRODUCTS IN PROPORTIONS NOT SPECIFIED BY
SHERWIN-WILLIAMS. REGULATORY REQUIREMENTS ARE SUBJECT TO CHANGE AND
MAY DIFFER BETWEEN VARIOUS LOCATIONS AND JURISDICTIONS. THE CUSTOMER
/BUYER/USER IS RESPONSIBLE TO ENSURE THAT HIS ACTIVITIES COMPLY WITH
ALL COUNTRY, FEDERAL, STATE, PROVINCIAL OR LOCAL LAWS. THE CONDITIONS
FOR USE OF THE PRODUCT ARE NOT UNDER THE CONTROL OF THE MANUFACTURER;
THE CUSTOMER/BUYER/USER IS RESPONSIBLE TO DETERMINE THE CONDITIONS
NECESSARY FOR THE SAFE USE OF THIS PRODUCT. THE CUSTOMER/BUYER/USER
SHOULD NOT USE THE PRODUCT FOR ANY PURPOSE OTHER THAN THE PURPOSE SHOWN
IN THE APPLICABLE SECTION OF THIS SDS WITHOUT FIRST REFERRING TO THE
SUPPLIER AND OBTAINING WRITTEN HANDLING INSTRUCTIONS. DUE TO THE
PROLIFERATION OF SOURCES FOR INFORMATION SUCH AS MANUFACTURER-SPECIFIC
SDS, THE MANUFACTURER CANNOT BE RESPONSIBLE FOR SDSS OBTAINED FROM ANY
OTHER SOURCE.