| Common Name: | PROPEX GREASE |
| Manufacturer: | MILWAUKEE ELECTRIC TOOL |
| SDS Revision Date: | 3/1/2015 |
| SDS Format: | GHS-US |
| Item Number(s): | 6CZA5 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
MILWAUKEE(R*)
SAFETY DATA SHEET
MAY BE USED TO COMPLY WITH OSHA'S HAZARD COMMUNICATION STANDARD
29 CFR 1910.1200.
THIS STANDARD MUST BE CONSULTED FOR SPECIFIC REQUIREMENTS.
| SECTION 1: PRODUCT AND COMPANY IDENTIFICATION |  |
PRODUCT NAME: PROPEX GREASE
PRODUCT MODELS: 49-08-2400
DRAWING NUMBER: 58-97-1280
ISSUE DATE: MARCH 2015
SUPERSEDES DATE: NOVEMBER 2011
MILWAUKEE ELECTRIC TOOL CORPORATION
13135 WEST LISBON ROAD
BROOKFIELD, WISCONSIN 53005
WWW.MILWAUKEETOOL.COM
COMPANY PHONE NUMBER:
262-781-3600 OR 1-800-729-3878
EMERGENCY CONTACT NUMBER: 1-800-424-9300
CHEMTREC: UNITED STATES ONLY
RECOMMENDED INTENDED PURPOSE TO BE USED AS A LUBRICANT.
| SECTION 2: HAZARDS IDENTIFICATION | |
HEALTH:
EYE IRRITATION: NO CLASSIFIED HAZARDS
SKIN IRRITATION: NO CLASSIFIED HAZARDS
SKIN SENSITISATION: CATEGORY 1
ACUTE TOXICITY, ORAL: NO CLASSIFIED HAZARDS
ACUTE TOXICITY, INHALATION: NO CLASSIFIED HAZARDS
ENVIRONMENTAL:
ACUTE TOXICITY: NO CLASSIFIED HAZARDS
CHRONIC TOXICITY: NO CLASSIFIED HAZARDS
PHYSICAL:
FLAMMABLE LIQUID: NO CLASSIFIED HAZARDS
GHS LABEL: EXCLAMATION MARK
WARNING:
HAZARD STATEMENTS PRECAUTIONARY STATEMENTS
MAY CAUSE EYE IRRITATION IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL
MINUTES. REMOVE CONTACT LENSES, IF PRESENT
AND EASY TO DO.
IF EYE IRRITATION PERSISTS:
GET MEDICAL ATTENTION/ADVICE.
MAY CAUSE ALLERGIC SKIN CONTAMINATED WORK CLOTHING SHOULD NOT BE
REACTION ALLOWED OUT OF THE WORK PLACE.
WEAR PROTECTIVE GLOVES/CLOTHING/EYE
PROTECTION/FACE PROTECTION
IF ON SKIN:
WASH WITH PLENTY OF SOAP AND WATER
IF SKIN IRRITATION OR RASH OCCURS CALL AND
GET MEDICAL ADVICE/ATTENTION
WASH CONTAMINATED CLOTHING BEFORE REUSE
MAY BE HARMFUL IF SWALLOWED IF SWALLOWED:
CALL A POISON CENTER OR DOCTOR/PHYSICIAN IF
YOU FEEL UNWELL.
MAY BE HARMFUL IF INHALED IF INHALED:
CALL A POISON CENTER OR DOCTOR/PHYSICIAN IF
YOU FEEL UNWELL.
MAY CAUSE ALLERGIC SKIN AVOID BREATHING,
REACTION DUST/FUMES/GAS/MIST/VAPORS/SPRAY.
CLASSIFIED HAZARDS:
THIS MATERIAL IS NOT HAZARDOUS UNDER THE CRITERIA OF THE FEDERAL OSHA
HAZARD COMMUNICATION STANDARD 29CFR 1910.1200. THIS SDS CONTAINS VALUABLE
INFORMATION FOR THE SAFE HANDLING AND PROPER USE OF THIS PRODUCT. SAVE THIS
SDS FOR FUTURE REFERENCE.
OTHER HAZARDS: NONE KNOWN
| SECTION 3: COMPOSITION / INFORMATION ON INGREDIENTS | |
COMPONENTS LISTED IN THIS SECTION MAY CONTRIBUTE TO THE POTENTIAL HAZARDS
ASSOCIATED WITH EXPOSURE TO THE CONCENTRATE. THE PRODUCT MAY CONTAIN
ADDITIONAL NON-HAZARDOUS OR TRADE-SECRET COMPONENTS.
CHEMICAL CHARACTERIZATION:
LUBRICATING GREASE:
THICKENING AGENT, ADDITIVES AND SOLID LUBRICANTS IN HIGHLY-REFINED MINERAL
OIL
CHEMICAL NAME CAS # CONCENTRATION(1)
PETROLATUM 8009-03-8 30-40
TRIETHANOLAMINE 102-71-6 <1
MOLYBDENUM DISULFIDE 1317-33-5 50-60
MINERAL OIL TRADE SECRET 5-10
LUBRICATING ADDITIVES TRADE SECRET 1-5
NOTE:
THIS PRODUCT HAS BEEN EVALUATED AND DOES NOT REQUIRE ANY HAZARD WARNING
LABEL UNDER THE OSHA HAZARD COMMUNICATION STANDARD.
(1) ALL CONCENTRATIONS ARE PERCENT BY WEIGHT UNLESS INGREDIENT IS A GAS.
GAS CONCENTRATIONS ARE IN PERCENT BY VOLUME
| SECTION 4: FIRST AID MEASURES | |
EYE CONTACT:
HOLD EYELIDS OPEN AND FLUSH WITH A STEADY, GENTLE STREAM OF WATER FOR AT
LEAST 15 MINUTES. IF SYMPTOMS PERSIST, CONTACT A PHYSICIAN.
SKIN CONTACT:
REMOVE PRODUCT FROM THE SKIN BY WASHING WITH A MILD SOAP AND WATER.
CONTAMINATED CLOTHING SHOULD BE REMOVED TO PREVENT PROLONGED EXPOSURE.
IF SYMPTOMS OF EXPOSURE PERSIST, CONTACT PHYSICIAN. IF PRODUCT IS INJECTED
INTO OR UNDER THE SKIN, SEEK TREATMENT IMMEDIATELY. (SEE NOTE TO PHYSICIAN)
INHALATION:
IF SIGNS OR SYMPTOMS OF OVEREXPOSURE OCCUR, REMOVE THE PERSON TO FRESH AIR.
IF SYMPTOMS PERSIST, SEEK MEDICAL ATTENTION.
INGESTION:
FIRST AID IS NOT NORMALLY REQUIRED; HOWEVER, IF SYMPTOMS OF INGESTION
PERSIST, SEEK MEDICAL ATTENTION.
NOTE TO PHYSICIAN:
WHEN USING HIGH-PRESSURE EQUIPMENT, INJECTION OF PRODUCT UNDER THE SKIN CAN
OCCUR. IN THIS CASE, THE CASUALTY SHOULD BE SENT IMMEDIATELY TO HOSPITAL.
DO NOT WAIT FOR SYMPTOMS TO DEVELOP. HIGH-PRESSURE HYDROCARBON INJECTION
INJURIES MAY PRODUCE SUBSTANTIAL NECROSIS OF UNDERLYING TISSUE DESPITE AN
INNOCUOUS APPEARING EXTERNAL WOUND. THESE INJURIES OFTEN REQUIRE EXTENSIVE
EMERGENCY SURGICAL DEBRIDEMENT AND ALL INJURIES SHOULD BE EVALUATED BY A
SPECIALIST IN ORDER TO ASSESS THE EXTENT OF INJURY. EARLY SURGICAL
TREATMENT WITHIN THE FIRST FEW HOURS MAY SIGNIFICANTLY REDUCE THE ULTIMATE
EXTENT OF INJURY.
| SECTION 5: FIRE FIGHTING MEASURES | |
NFPA 704 HAZARD CLASS: NO DATA
HMIS:
HEALTH 1
FLAMMABILITY 0
REACTIVITY 0
PERSONAL PROTECTION X
0 (MINIMAL)
1 (SLIGHT)
2 (MODERATE)
3 (SERIOUS)
4 (SEVERE)
EXTINGUISHING MEDIA:
IN ACCORDANCE WITH NFPA GUIDANCE, DRY CHEMICAL, FOAM, OR CO2 FIRE
EXTINGUISHERS ARE ALL ACCEPTABLE. NOTE THAT WHILE WATER FOG EXTINGUISHERS
ARE ALSO ACCEPTABLE, DO NOT APPLY A DIRECT STREAM OF WATER ONTO BURNING
PRODUCT BECAUSE IT MAY CAUSE SPREADING AND INCREASE FIRE INTENSITY.
UNUSUAL FIRE & EXPLOSION HAZARDS: NO FURTHER DATA KNOWN.
FIRE-FIGHTING PROCEDURES AND EQUIPMENT:
EMERGENCY RESPONDERS IN THE DANGER AREA SHOULD WEAR BUNKER GEAR AND
SELF-CONTAINED BREATHING APPARATUS FOR FIRES BEYOND THE INCIPIENT STAGE.
SEE SECTION 8 OF THE MSDS FOR OTHER PPE TO BE WORN AS CONDITIONS WARRANT.
SEE SECTION 9 FOR FLAMMABLE PROPERTIES INCLUDING FLASH POINT AND FLAMMABLE
(EXPLOSIVE) LIMITS.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
CLEAN-UP MEASURES:
IMPORTANT:
AS WITH ANY SPILL OR LEAD, BEFORE RESPONDING ENSURE THAT YOU ARE FAMILIAR
WITH THE POTENTIAL HAZARDS AND RECOMMENDATIONS OF THE MSDS. APPROPRIATE
PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN. SEE SECTION 8 OF THIS MSDS FOR
PPE RECOMMENDATIONS.
IF POSSIBLE, SAFELY CONTAIN THE SPILL WITH DIKES OR OTHER SPILL RESPONSE
EQUIPMENT APPROPRIATE FOR PETROLEUM OR ORGANIC MATERIAL RELEASES. TAKE
MEASURES TO PREVENT SPREADING OF PRODUCT. NOTE THAT WHILE PRODUCT WILL
IGNITE IT WILL NOT READILY BURN. HOWEVER, AS A PRECAUTION ELIMINATE
IGNITION SOURCES. PREVENT FROM ENTERING SEWERS OR WATERWAYS. LARGE VOLUMES
MAY BE TRANSFERRED TO AN APPROPRIATE CONTAINER FOR PROPER DISPOSAL. SMALL
VOLUMES OR RESIDUES MAY BE SOAKED UP WITH ABSORBENTS. SPILL RESPONSE
MATERIALS SHOULD BE COLLECTED FOR PROPER DISPOSAL.
| SECTION 7: HANDLING AND STORAGE | |
HANDLING:
AS WITH ANY INDUSTRIAL CHEMICAL, HANDLE THE PRODUCT IN A MANNER THAT
MINIMIZES EXPOSURE TO PRACTICABLE LEVELS. PRIOR TO HANDLING, CONSULT
SECTION 8 OF THIS MSDS TO EVALUATE PERSONAL PROTECTIVE EQUIPMENT NEEDS.
OPEN CONTAINERS SLOWLY TO RELIEVE ANY PRESSURE. FOLLOW ALL OTHER STANDARD
INDUSTRIAL HYGIENE PRACTICES.
EMPTY CONTAINERS MAY CONTAIN PRODUCT RESIDUE. ALL SAFETY PRECAUTIONS TAKEN
WHEN HANDLING THIS PRODUCT SHOULD ALSO BE TAKEN WHEN HANDLING EMPTY DRUMS
AND CONTAINERS. KEEP CONTAINERS CLOSED WHEN NOT IN USE.
PRODUCT RESIDUE IN EMPTY CONTAINERS IS COMBUSTIBLE BUT WILL NOT READILY
BURN. NOTE HOWEVER, THAT EXCESSIVE HEATING OR CUTTING OF EMPTY CONTAINERS
MAY CREATE AN IGNITIONS SOURCE SUFFICIENT TO START A FIRE AND IN EXTREME
CASES, CAUSE AN EXPLOSION.
STORAGE:
PROTECT PRODUCT QUALITY BY STORING INDOORS AND AWAY FROM EXTREME
TEMPERATURES. CLOSE ALL CONTAINERS WHEN NOT IN USE.
SPECIAL COMMENTS: NO FURTHER DATA KNOWN.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
SELECTION OF PERSONAL PROTECTIVE EQUIPMENT SHOULD BE BASED UPON THE
ANTICIPATED EXPOSURE AND MADE IN ACCORDANCE WITH OSHA'S PERSONAL PROTECTIVE
EQUIPMENT STANDARD FOUND IN 29 CFR 1910 SUBPART I. THE FOLLOWING
INFORMATION MAY BE USED TO ASSIST IN PPE SELECTION.
INGREDIENT OSHA PEL ACGIH TLV CALIFORNIA PROP IARC/NTP
65 REG. Y/N Y/N
PETROLATUM NOT NOT N N
ESTABLISHED ESTABLISHED
TRIETHANOLAMINE TWA: TWA: N N
5 MG/M3* 5 MG/M3*
MOLYBDENUM TWA: TWA: N N
DISULFIDE 3 MG/M3* 3 MG/M3*
MINERAL OIL TWA TWA N N
5 MG/M3* 5 MG/M3*
LUBRICATING NOT NOT N N
ADDITIVES ESTABLISHED ESTABLISHED
NOTE:
THIS PRODUCT HAS BEEN EVALUATED AND DOES NOT REQUIRE ANY HAZARD WARNING
LABEL UNDER THE OSHA HAZARD COMMUNICATION STANDARD.
* AS OIL MIST, IF GENERATING
EYE PROTECTION:
WEAR EYE PROTECTION APPROPRIATE TO PREVENT EYE EXPOSURE. WHERE SPLASHING
IS NOT LIKELY, CHEMICAL SAFETY GLASSES WITH SIDE SHIELDS ARE RECOMMENDED.
WHERE SPLASHING MAY OCCUR, CHEMICAL GOGGLES OR FULL FACE SHIELD IS
RECOMMENDED.
SKIN PROTECTION:
GLOVES ARE NOT NORMALLY NEEDED DURING NORMAL CONDITIONS OF USE. IF HEALTH
EFFECTS ARE EXPERIENCED, OIL OR CHEMICAL RESISTANT GLOVES SUCH AS BUTYL OR
NITRILE ARE RECOMMENDED.
WHERE SPLASHING OR SOAKING IS LIKELY, WEAR OIL OR CHEMICAL RESISTANT
CLOTHING TO PREVENT EXPOSURE.
RESPIRATORY PROTECTION:
A RESPIRATOR MAY BE WORN TO REDUCE THE EXPOSURE TO DUST. SELECT A
NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE FOR THE TYPE AND PHYSICAL
CHARACTER OF THE AIRBORNE MATERIAL. A SELF-CONTAINED BREATHING APPARATUS IS
RECOMMENDED IN ALL SITUATIONS WHERE AIRBORNE CONTAMINANT CONCENTRATION HAS
NOT BEEN CONFIRMED TO BE BELOW SAFE LEVELS. RESPIRATOR USE SHOULD COMPLY
WITH THE OSHA RESPIRATOR PROTECTION STANDARD FOUND IN CFR 1910.134.
ENGINEERING CONTROLS:
NORMAL GENERAL VENTILATION IS EXPECTED TO BE ADEQUATE. IT IS RECOMMENDED
THAT VENTILATION BE DESIGNED IN ALL INSTANCES TO MAINTAIN AIRBORNE
CONCENTRATIONS AT LOWEST PRACTICABLE LEVELS. VENTILATION SHOULD AT A
MINIMUM, PREVENT AIRBORNE CONCENTRATIONS FROM EXCEEDING ANY EXPOSURE LIMITS
LISTED IN SECTION 2 OF THIS MSDS.
THE USER MAY WISH TO REFER TO 29 CFR 1910.1000 (D) (2) AND THE ACGIH
"THRESHOLD LIMIT VALUES FOR CHEMICAL SUBSTANCES AND PHYSICAL AGENTS
BIOLOGICAL EXPOSURE INDICES" (APPENDIX C) FOR THE DETERMINATION OF EXPOSURE
LIMITS OF MIXTURES. AN INDUSTRIAL HYGIENIST OR SIMILAR PROFESSIONAL MAY BE
CONSULTED TO CONFIRM THAT THE CALCULATED EXPOSURE LIMITS APPLY.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
DATA REPRESENT TYPICAL VALUES AND ARE NOT INTENDED TO BE SPECIFICATIONS.
NA=NOT APPLICABLE
ND=NOT DETERMINED
PHYSICAL STATE: SEMI-SOLID
COLOUR: DARK GRAY
ODOR: OIL ODOR
ODOR THRESHOLD: ND
PH: NA
MELTING/FREEZING POINT: NA
VOC CONTENT: NA
BOILING POINT: NA
FLASH POINT: 200 DEG. C
EVAPORATION RATE: ND
SPECIFIC GRAVITY: ND
FLAMMABILITY (SOLID, GAS): NA
UPPER EXPLOSIVE LIMITS (VOL % IN AIR): NA
LOWER EXPLOSIVE LIMITS (VOL % IN AIR): NA
VAPOR PRESSURE: NA
VAPOR DENSITY: NA
RELATIVE DENSITY: 1.45
SOLUBILITY: INSOLUABLE
PARTITION COEFFICIENT: NA
AUTO-IGNITION TEMPERATURE: NA
DECOMPOSITION TEMPERATURE: NA
VISCOSITY: ND
| SECTION 10: STABILITY AND REACTIVITY | |
INCOMPATIBLE MATERIALS: THIS PRODUCT IS INCOMPATIBLE WITH STRONG ACIDS.
DECOMPOSITION PRODUCTS MAY INCLUDE:
THERMAL DECOMPOSITION PRODUCTS ARE DEPENDENT ON COMBUSTION CONDITIONS.
A COMPLEX MIXTURE OF AIRBORNE SOLID, LIQUID, PARTICULATES AND GASSES MAY
EVOLVE WHEN THE MATERIAL BURNS.
CONDITIONS TO AVOID:
AVOID CONTACT WITH INCOMPATIBLE MATERIALS AND EXPOSURE TO EXTREME
TEMPERATURES.
POLYMERIZATION: THIS PRODUCT IS NOT EXPECTED TO POLYMERIZE.
CHEMICAL STABILITY: THIS PRODUCT IS STABLE.
REACTIVITY: STABLE UNDER NORMAL AMBIENT AND ANTICIPATED CONDITIONS OF USE.
| SECTION 11: TOXICOLOGY INFORMATION | |
LIKELY ROUTES OF EXPOSURE: INHALATION, EYE AND SKIN CONTACT
ACUTE SYMPTOMS AND EFFECTS:
INHALATION: NO FURTHER TOXICOLOGICAL DATA KNOWN
EYE CONTACT: NO FURTHER TOXICOLOGICAL DATA KNOWN
SKIN CONTACT: NO FURTHER TOXICOLOGICAL DATA KNOWN
INGESTION: NO FURTHER TOXICOLOGICAL DATA KNOWN
OTHER: NO FURTHER DATA KNOWN.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
THIS PRODUCT HAS NOT BEEN EVALUATED FOR ECOTOXICITY. AS WITH ANY INDUSTRIAL
CHEMICAL, EXPOSURE TO THE ENVIRONMENT SHOULD BE PREVENTED AND MINIMIZED
WHEREVER POSSIBLE.
TOXICITY: NO DATA AVAILABLE
PERSISTENCE AND DEGRADABILITY (BIOPERSISTENCY & BIODEGRADABILITY):
THE DEGREE OF BIODEGRADABILITY AND PERSISTENCE OF THIS PRODUCT HAS NOT BEEN
DETERMINED.
POTENTIAL OF BIOACCUMULATION: NO DATA AVAILABLE
MOBILITY IN SOIL: NO DATA AVAILABLE
OTHER ADVERSE EFFECTS: NO DATA AVAILABLE
| SECTION 13: DISPOSAL CONSIDERATIONS | |
WASTE DISPOSAL:
ENSURE THAT COLLECTION, TRANSPORT, TREATMENT, AND DISPOSAL OF WASTE
PRODUCT, CONTAINERS AND RINSATE COMPLIES WITH ALL APPLICABLE LAWS AND
REGULATIONS. NOTE THAT USE, MIXTURE, PROCESSING, OR CONTAMINATION OF THE
PRODUCT MAY CAUSE THE MATERIAL TO BE CLASSIFIED AS A HAZARDOUS WASTE. IT IS
THE RESPONSIBILITY OF THE PRODUCT USER OR OWNER TO DETERMINE AT THE TIME OF
DISPOSAL, WHETHER THE PRODUCT IS REGULATED AS A HAZARDOUS WASTE.
| SECTION 14: TRANSPORT INFORMATION | |
DOT HAZARDOUS MATERIAL INFORMATION: NOT OTHERWISE DOT REGULATED.
| SECTION 15: REGULATORY INFORMATION | |
FEDERAL REGULATIONS:
SARA 313:
THIS PRODUCT CONTAINS NONE OF THE SUBSTANCES SUBJECT TO THE REPORTING
REQUIREMENTS OF SECTION 313 OF TITLE III OF THE SUPERFUND AMENDMENTS
AND REAUTHORIZATION ACT OF 1986 AND 40 CFR PART 372.
CLEAN WATER ACT / OIL POLLUTION ACT:
THIS PRODUCT CONTAINS MINERAL OIL AND IS SUBJECT TO REGULATION BY SECTION
311 OF THE CLEAN WATER ACT AND THE OIL POLLUTION ACT. RELEASES OF THE
PRODUCT INTO OR LEADING TO SURFACE WATERS MUST BE REPORTED TO THE NATIONAL
RESPONSE CENTER AT 1-800-424-8802.
CERCLA REPORTABLE QUANTITY:
ANY COMPONENTS LISTED BELOW HAVE BEEN ASSIGNED A REPORTABLE QUANTITY (RQ)
BY THE FEDERAL EPA. RELEASES OF THE PRODUCT INTO THE ENVIRONMENT THAT
EXCEED THE RQ FOR A PARTICULAR COMPONENT MUST BE REPORTED TO THE NATIONAL
RESPONSE CENTER AT 1-800-424-8802.
TOXIC SUBSTANCE CONTROL ACT:
THE COMPONENTS OF THIS PRODUCT ARE LISTED ON THE TSCA INVENTORY.
OZONE DEPLETING SUBSTANCES:
THIS PRODUCT CONTAINS NO OZONE DEPLETING SUBSTANCES AS DEFINED BY THE CLEAN
AIR ACT.
HAZARDOUS AIR POLLUTANTS:
ANY COMPONENTS LISTED BELOW ARE DEFINED BY THE FEDERAL EPA AS HAZARDOUS AIR
POLLUTANTS.
STATE REGULATIONS:
THIS PRODUCT CONTAINS MINERAL OIL, AND AS USED, MAY BE REGULATED BY THE
STATE USED OIL REGULATIONS. CHECK WITH THE APPROPRIATE STATE AGENCY TO
DETERMINE WHETHER SUCH A REGULATION EXISTS.
NO FURTHER DATA KNOWN.
| SECTION 16: OTHER INFORMATION | |
ABBREVIATIONS:
TSCA: TOXIC SUBSTANCE CONTROL ACT
ICAO: INTERNATIONAL CIVIL AVIATION ORGANIZATION
IMDG: INTERNATIONAL MARITIME DANGEROUS
OSHA: OCCUPATIONAL SAFETY AND HEALTH
IARC/NTP:
INTERNATIONAL AGENCY FOR RESEARCH ON CANCER/NATIONAL TOXICOLOGY PROGRAM
SARA: SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT OF 1986
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
NIOSH/MSHA:
NATIONAL INSTITUTE FOR OCCUPATIONAL SAFETY HEALTH/MINE SAFETY AND HEALTH
ADMINISTRATION
WHMIS: WORKPLACE HAZARDOUS MATERIALS INFORMATION SYSTEM
PREPARED BY: MILWAUKEE ELECTRIC TOOL CORPORATION
THE INFORMATION AND RECOMMENDATIONS SET FORTH ARE MADE IN GOOD FAITH AND
BELIEVED TO BE ACCURATE AS OF THE DATE OF PREPARATION. MILWAUKEE ELECTRIC
TOOL CORPORATION MAKES NO WARRANTY, EXPRESSED OR IMPLIED, REGARDING THE
ACCURACY OF THIS DATA OR THE RESULTS TO BE OBTAINED FROM THE USE THERETO.
ALL RISKS ASSOCIATED WITH PRODUCT USE ARE ASSUMED BY THE USER.
58-97-1280
PROPEX GREASE
03A