| Common Name: | EPOXY 1-GL 2PK 9100 MARLIN BLUE, 9122402 |
| Manufacturer: | RUST-OLEUM |
| SDS Revision Date: | 8/7/2018 |
| SDS Format: | GHS-US |
| Item Number(s): | 6H378 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
DATE PRINTED: 8/7/2018
SAFETY DATA SHEET
RUST-OLEUM CORPORATION
TRUSTED QUALITY SINCE 1921
WWW.RUSTOLEUM.COM
| 1. IDENTIFICATION |  |
PRODUCT NAME: EPOXY 1-GL 2PK 9100 MARLIN BLUE
PRODUCT IDENTIFIER: 9122402
RECOMMENDED USE: TOPCOAT/EPOXY
REVISION DATE: 8/7/2018
SUPERCEDES DATE: 3/14/2018
SUPPLIER:
RUST-OLEUM CORPORATION
11 HAWTHORN PARKWAY
VERNON HILLS, IL 60061
USA
RUST-OLEUM CANADA (ROCA)
200 CONFEDERATION PARKWAY
CONCORD, ON L4K 4T8
CANADA
EMERGENCY PHONE: 800-387-3625
MANUFACTURER:
RUST-OLEUM CORPORATION
11 HAWTHORN PARKWAY
VERNON HILLS, IL 60061
USA
PREPARER: REGULATORY DEPARTMENT
EMERGENCY TELEPHONE:
24 HOUR HOTLINE: 847-367-7700
| 2. HAZARD IDENTIFICATION | |
CLASSIFICATION:
SYMBOL(S) OF PRODUCT:
FLAME
EXCLAMATION MARK
HEALTH HAZARD
SIGNAL WORD: WARNING
POSSIBLE HAZARDS:
36% OF THE MIXTURE CONSISTS OF INGREDIENT(S) OF UNKNOWN ACUTE TOXICITY.
GHS HAZARD STATEMENTS:
FLAMMABLE LIQUID, CATEGORY 3:
H226: FLAMMABLE LIQUID AND VAPOUR.
CARCINOGENICITY, CATEGORY 2:
H351: SUSPECTED OF CAUSING CANCER.
STOT, SINGLE EXPOSURE, CATEGORY 3, RTI:
H335: MAY CAUSE RESPIRATORY IRRITATION.
STOT, REPEATED EXPOSURE, CATEGORY 2:
H373: MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.
SKIN IRRITATION, CATEGORY 2:
H315: CAUSES SKIN IRRITATION.
EYE IRRITATION, CATEGORY 2:
H319: CAUSES SERIOUS EYE IRRITATION.
SKIN SENSITIZER, CATEGORY 1:
H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
GHS LABEL PRECAUTIONARY STATEMENTS:
P210:
KEEP AWAY FROM HEAT, HOT SURFACES, SPARKS, OPEN FLAMES AND OTHER IGNITION
SOURCES. NO SMOKING.
P280:
WEAR PROTECTIVE GLOVES/PROTECTIVE CLOTHING/EYE PROTECTION/FACE PROTECTION.
P303+P361+P353:
IF ON SKIN (OR HAIR):
TAKE OFF IMMEDIATELY ALL CONTAMINATED CLOTHING. RINSE SKIN WITH WATER/
SHOWER.
P370+P378:
IN CASE OF FIRE:
USE ALCOHOL FILM FORMING FOAM, CARBON DIOXIDE, DRY CHEMICAL, DRY SAND TO
EXTINGUISH.
P403+P235: STORE IN A WELL-VENTILATED PLACE. KEEP COOL.
P501:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH LOCAL, REGIONAL AND
NATIONAL REGULATIONS.
P201: OBTAIN SPECIAL INSTRUCTIONS BEFORE USE.
P308+P313:
IF EXPOSED OR CONCERNED: GET MEDICAL ADVICE/ATTENTION.
P405: STORE LOCKED UP.
P271: USE ONLY OUTDOORS OR IN A WELL-VENTILATED AREA.
P304+P340:
IF INHALED:
REMOVE PERSON TO FRESH AIR AND KEEP COMFORTABLE FOR BREATHING.
P312: CALL A POISON CENTER OR DOCTOR/PHYSICIAN IF YOU FEEL UNWELL.
P403+P233: STORE IN A WELL-VENTILATED PLACE. KEEP CONTAINER TIGHTLY CLOSED.
P260: DO NOT BREATHE DUST/FUME/GAS/MIST/VAPORS/SPRAY.
P264: WASH HANDS THOROUGHLY AFTER HANDLING.
P302+P352:
IF ON SKIN: WASH WITH PLENTY OF SOAP AND WATER.
P321: FOR SPECIFIC TREATMENT SEE LABEL
P332+P313:
IF SKIN IRRITATION OCCURS: GET MEDICAL ADVICE/ATTENTION.
P362+P364: TAKE OFF CONTAMINATED CLOTHING AND WASH IT BEFORE REUSE.
P305+P351+P338:
IF IN EYES:
RINSE CAUTIOUSLY WITH WATER FOR SEVERAL MINUTES. REMOVE CONTACT LENSES,
IF PRESENT AND EASY TO DO. CONTINUE RINSING.
P337+P313:
IF EYE IRRITATION PERSISTS: GET MEDICAL ADVICE/ATTENTION.
P272:
CONTAMINATED WORK CLOTHING SHOULD NOT BE ALLOWED OUT OF THE WORKPLACE.
P333+P313:
IF SKIN IRRITATION OR RASH OCCURS: GET MEDICAL ADVICE/ATTENTION.
GHS SDS PRECAUTIONARY STATEMENTS:
P240: GROUND/BOND CONTAINER AND RECEIVING EQUIPMENT.
P241: USE EXPLOSION-PROOF ELECTRICAL/VENTILATING/LIGHTING/EQUIPMENT.
P242: USE ONLY NON-SPARKING TOOLS.
P243: TAKE PRECAUTIONARY MEASURES AGAINST STATIC DISCHARGE.
P363: WASH CONTAMINATED CLOTHING BEFORE REUSE.
| 3. COMPOSITION / INFORMATION ON INGREDIENTS | |
HAZARDOUS SUBSTANCES:
CHEMICAL NAME CAS-NO. WT.% GHS SYMBOLS GHS STATEMENTS
EPICHLOROHYDRIN- 25068-38-6 44 GHS07 H315-317-319-335
BISPHENOL A RESIN
HYDROUS MAGNESIUM 14807-96-6 20 NOT AVAILABLE NOT AVAILABLE
SILICATE
TITANIUM DIOXIDE 13463-67-7 16 NOT AVAILABLE NOT AVAILABLE
XYLENES 1330-20-7 8.1 GHS02-GHS07 H226-315-319-332
(O-, M-, P- ISOMERS)
METHYL ISOBUTYL 108-10-1 5.3 GHS02-GHS06 H225-319-331-335
KETONE
ETHYLBENZENE 100-41-4 1.9 GHS02-GHS07- H225-304-332-
GHS08 351-373
| 4. FIRST-AID MEASURES | |
FIRST AID - EYE CONTACT:
IMMEDIATELY FLUSH EYES WITH PLENTY OF WATER FOR AT LEAST 15 MINUTES HOLDING
EYELIDS OPEN. GET MEDICAL ATTENTION. DO NOT ALLOW RUBBING OF EYES OR
KEEPING EYES CLOSED.
FIRST AID - SKIN CONTACT:
WASH SKIN WITH SOAP AND WATER. REMOVE CONTAMINATED CLOTHING. GET MEDICAL
ATTENTION IF IRRITATION DEVELOPS OR PERSISTS.
FIRST AID - INHALATION:
REMOVE TO FRESH AIR. IF NOT BREATHING, GIVE ARTIFICIAL RESPIRATION.
IF BREATHING IS DIFFICULT, GIVE OXYGEN. GET IMMEDIATE MEDICAL ATTENTION.
DO NOT USE MOUTH-TO-MOUTH RESUSCITATION. IF YOU EXPERIENCE DIFFICULTY IN
BREATHING, LEAVE THE AREA TO OBTAIN FRESH AIR. IF CONTINUED DIFFICULTY IS
EXPERIENCED, GET MEDICAL ASSISTANCE IMMEDIATELY.
FIRST AID - INGESTION:
ASPIRATION HAZARD:
DO NOT INDUCE VOMITING OR GIVE ANYTHING BY MOUTH BECAUSE THIS MATERIAL
CAN ENTER THE LUNGS AND CAUSE SEVERE LUNG DAMAGE. GET IMMEDIATE MEDICAL
ATTENTION. IF SWALLOWED, GET MEDICAL ATTENTION.
| 5. FIRE-FIGHTING MEASURES | |
EXTINGUISHING MEDIA:
ALCOHOL FILM FORMING FOAM, CARBON DIOXIDE, DRY CHEMICAL, WATER FOG
UNUSUAL FIRE AND EXPLOSION HAZARDS:
ISOLATE FROM HEAT, ELECTRICAL EQUIPMENT, SPARKS AND OPEN FLAME. VAPORS CAN
TRAVEL TO A SOURCE OF IGNITION AND FLASH BACK. VAPORS MAY FORM EXPLOSIVE
MIXTURES WITH AIR. NO UNUSUAL FIRE OR EXPLOSION HAZARDS NOTED. CLOSED
CONTAINERS MAY EXPLODE WHEN EXPOSED TO EXTREME HEAT DUE TO BUILDUP OF
STEAM. KEEP CONTAINERS TIGHTLY CLOSED.
SPECIAL FIREFIGHTING PROCEDURES:
WATER MAY BE USED TO COOL CLOSED CONTAINERS TO PREVENT PRESSURE BUILDUP
AND POSSIBLE AUTOIGNITION OR EXPLOSION. EVACUATE AREA AND FIGHT FIRE FROM
A SAFE DISTANCE. USE WATER SPRAY TO KEEP FIRE-EXPOSED CONTAINERS COOL.
CONTAINERS MAY EXPLODE WHEN HEATED.
SPECIAL FIRE AND EXPLOSION HAZARD (COMBUSTIBLE DUST): NO INFORMATION
| 6. ACCIDENTAL RELEASE MEASURES | |
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED:
CONTAIN SPILLED LIQUID WITH SAND OR EARTH. DO NOT USE COMBUSTIBLE MATERIALS
SUCH AS SAWDUST. ELIMINATE ALL IGNITION SOURCES; USE EXPLOSION-PROOF
EQUIPMENT. PLACE MATERIAL IN A CONTAINER AND DISPOSE OF ACCORDING TO LOCAL,
PROVINCIAL, STATE AND FEDERAL REGULATIONS. REMOVE ALL SOURCES OF IGNITION,
VENTILATE AREA AND REMOVE WITH INERT ABSORBENT AND NON-SPARKING TOOLS.
DISPOSE OF ACCORDING TO LOCAL, STATE (PROVINCIAL) AND FEDERAL REGULATIONS.
DO NOT INCINERATE CLOSED CONTAINERS. VENTILATE AREA, ISOLATE SPILLED
MATERIAL, AND REMOVE WITH INERT ABSORBENT. DISPOSE OF CONTAMINATED
ABSORBENT, CONTAINER, AND UNUSED CONTENTS IN ACCORDANCE WITH LOCAL,
STATE, AND FEDERAL REGULATIONS.
| 7. HANDLING AND STORAGE | |
HANDLING:
WASH THOROUGHLY AFTER HANDLING. WASH HANDS BEFORE EATING. USE ONLY WITH
ADEQUATE VENTILATION. FOLLOW ALL SDS AND LABEL PRECAUTIONS EVEN AFTER
CONTAINER IS EMPTIED BECAUSE IT MAY RETAIN PRODUCT RESIDUES. REMOVE
CONTAMINATED CLOTHING AND LAUNDER BEFORE REUSE. AVOID BREATHING FUMES,
VAPORS, OR MIST. AVOID CONTACT WITH EYES, SKIN AND CLOTHING.
STORAGE:
KEEP CONTAINERS TIGHTLY CLOSED. ISOLATE FROM HEAT, ELECTRICAL EQUIPMENT,
SPARKS AND OPEN FLAME. KEEP AWAY FROM HEAT, SPARKS, FLAME AND SOURCES OF
IGNITION. KEEP CONTAINER CLOSED WHEN NOT IN USE. PRODUCT SHOULD BE STORED
IN TIGHTLY SEALED CONTAINERS AND PROTECTED FROM HEAT, MOISTURE, AND
FOREIGN MATERIALS. STORE IN A DRY, WELL VENTILATED PLACE. KEEP CONTAINER
TIGHTLY CLOSED WHEN NOT IN USE. AVOID EXCESS HEAT. DO NOT STORE ABOVE
120 DEG. F. STORE LARGE QUANTITIES IN BUILDINGS DESIGNED AND PROTECTED
FOR STORAGE OF NFPA CLASS II COMBUSTIBLE LIQUIDS.
ADVICE ON SAFE HANDLING OF COMBUSTIBLE DUST: NO INFORMATION
| 8. EXPOSURE CONTROLS / PERSONAL PROTECTION | |
CHEMICAL NAME CAS-NO. WEIGHT % LESS THAN
EPICHLOROHYDRIN-BISPHENOL A RESIN 25068-38-6 45.0
HYDROUS MAGNESIUM SILICATE 14807-96-6 25.0
TITANIUM DIOXIDE 13463-67-7 20.0
XYLENES (O-, M-, P- ISOMERS) 1330-20-7 10.0
METHYL ISOBUTYL KETONE 108-10-1 10.0
ETHYLBENZENE 100-41-4 5.0
CHEMICAL NAME ACGIH ACGIH OSHA OSHA
TLV-TWA TLV-STEL PEL-TWA PEL-CEILING
EPICHLOROHYDRIN-BISPHENOL A N.E. N.E. N.E. N.E.
RESIN
HYDROUS MAGNESIUM SILICATE 2 MG/M3 N.E. N.E. N.E.
TITANIUM DIOXIDE 10 MG/M3 N.E. 15 MG/M3 N.E.
XYLENES (O-, M-, P- ISOMERS) 100 PPM 150 PPM 100 PPM N.E.
METHYL ISOBUTYL KETONE 20 PPM 75 PPM 100 PPM N.E.
ETHYLBENZENE 20 PPM N.E. 100 PPM N.E.
PERSONAL PROTECTION:
ENGINEERING CONTROLS:
USE PROCESS ENCLOSURES, LOCAL EXHAUST VENTILATION, OR OTHER ENGINEERING
CONTROLS TO CONTROL AIRBORNE LEVELS BELOW RECOMMENDED EXPOSURE LIMITS.
PREVENT BUILD-UP OF VAPORS BY OPENING ALL DOORS AND WINDOWS TO ACHIEVE
CROSS-VENTILATION.
RESPIRATORY PROTECTION:
A RESPIRATORY PROTECTION PROGRAM THAT MEETS OSHA 1910.134 AND ANSI Z88.2
REQUIREMENTS MUST BE FOLLOWED WHENEVER WORKPLACE CONDITIONS WARRANT A
RESPIRATOR'S USE. A NIOSH/MSHA APPROVED AIR PURIFYING RESPIRATOR WITH AN
ORGANIC VAPOR CARTRIDGE OR CANISTER MAY BE PERMISSIBLE UNDER CERTAIN
CIRCUMSTANCES WHERE AIRBORNE CONCENTRATIONS ARE EXPECTED TO EXCEED
EXPOSURE LIMITS.
PROTECTION PROVIDED BY AIR PURIFYING RESPIRATORS IS LIMITED. USE A POSITIVE
PRESSURE AIR SUPPLIED RESPIRATOR IF THERE IS ANY POTENTIAL FOR AN
UNCONTROLLED RELEASE, EXPOSURE LEVELS ARE NOT KNOWN, OR IN ANY OTHER
CIRCUMSTANCES WHERE AIR PURIFYING RESPIRATORS MAY NOT PROVIDE ADEQUATE
PROTECTION.
SKIN PROTECTION:
USE IMPERVIOUS GLOVES TO PREVENT SKIN CONTACT AND ABSORPTION OF THIS
MATERIAL THROUGH THE SKIN. NITRILE OR NEOPRENE GLOVES MAY AFFORD ADEQUATE
SKIN PROTECTION. USE GLOVES TO PREVENT PROLONGED SKIN CONTACT.
EYE PROTECTION:
USE SAFETY EYEWEAR DESIGNED TO PROTECT AGAINST SPLASH OF LIQUIDS.
OTHER PROTECTIVE EQUIPMENT:
REFER TO SAFETY SUPERVISOR OR INDUSTRIAL HYGIENIST FOR FURTHER INFORMATION
REGARDING PERSONAL PROTECTIVE EQUIPMENT AND ITS APPLICATION. REFER TO
SAFETY SUPERVISOR OR INDUSTRIAL HYGIENIST FOR FURTHER GUIDANCE REGARDING
TYPES OF PERSONAL PROTECTIVE EQUIPMENT AND THEIR APPLICATIONS.
HYGIENIC PRACTICES:
WASH THOROUGHLY WITH SOAP AND WATER BEFORE EATING, DRINKING OR SMOKING.
REMOVE CONTAMINATED CLOTHING IMMEDIATELY AND LAUNDER BEFORE REUSE.
ENGINEERING MEASURES FOR COMBUSTIBLE DUST: NO INFORMATION
| 9. PHYSICAL AND CHEMICAL PROPERTIES | |
APPEARANCE: LIQUID
PHYSICAL STATE: LIQUID
ODOR: SOLVENT LIKE
ODOR THRESHOLD: N.E.
RELATIVE DENSITY: 1.439
PH: N.A.
FREEZE POINT, DEG. C: NE
VISCOSITY: N.D.
SOLUBILITY IN WATER: NEGLIGIBLE
PARTITION COEFFICIENT, N-OCTANOL/WATER: N.D.
DECOMPOSTION TEMP., DEG. C: N.D.
BOILING RANGE, DEG. C: 117 - 537
EXPLOSIVE LIMITS, VOL%: 1.0 - 8.0
FLAMMABILITY: SUPPORTS COMBUSTION
FLASH POINT, DEG. C: 26
EVAPORATION RATE: SLOWER THAN ETHER
AUTO-IGNITION TEMP., DEG. C: N.D.
VAPOR DENSITY: HEAVIER THAN AIR
VAPOR PRESSURE: N.D.
(SEE "OTHER INFORMATION" SECTION FOR ABBREVIATION LEGEND)
| 10. STABILITY AND REACTIVITY | |
CONDITIONS TO AVOID:
AVOID ALL POSSIBLE SOURCES OF IGNITION. AVOID TEMPERATURES ABOVE 120 DEG. F
(49 DEG. C).
INCOMPATIBILITY:
INCOMPATIBLE WITH STRONG OXIDIZING AGENTS, STRONG ACIDS AND STRONG
ALKALIES.
HAZARDOUS DECOMPOSITION:
CONTAINS SOLVENTS WHICH MAY FORM CARBON MONOXIDE, CARBON DIOXIDE, AND
FORMALDEHYDE. BY OPEN FLAME, CARBON MONOXIDE AND CARBON DIOXIDE. WHEN
HEATED TO DECOMPOSITION, IT EMITS ACRID SMOKE AND IRRITATING FUMES.
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR UNDER NORMAL CONDITIONS.
STABILITY:
MAY FORM PEROXIDES OF UNKOWN STABILITY. THIS PRODUCT IS STABLE UNDER NORMAL
STORAGE CONDITIONS.
| 11. TOXICOLOGICAL INFORMATION | |
EFFECTS OF OVEREXPOSURE - EYE CONTACT: CAUSES SERIOUS EYE IRRITATION
EFFECTS OF OVEREXPOSURE - SKIN CONTACT:
PROLONGED OR REPEATED SKIN CONTACT MAY CAUSE IRRITATION. CAUSES SKIN
IRRITATION. ALLERGIC REACTIONS ARE POSSIBLE.
EFFECTS OF OVEREXPOSURE - INHALATION:
HARMFUL IF INHALED. AVOID BREATHING FUMES, SPRAY, VAPORS, OR MIST. MAY
CAUSE HEADACHES AND DIZZINESS. HIGH VAPOR CONCENTRATIONS ARE IRRITATING
TO THE EYES, NOSE, THROAT AND LUNGS. HIGH GAS, VAPOR, MIST OR DUST
CONCENTRATIONS MAY BE HARMFUL IF INHALED. PROLONGED OR EXCESSIVE
INHALATION MAY CAUSE RESPIRATORY TRACT IRRITATION.
EFFECTS OF OVEREXPOSURE - INGESTION:
HARMFUL IF SWALLOWED. ASPIRATION HAZARD IF SWALLOWED; CAN ENTER LUNGS AND
CAUSE DAMAGE.
EFFECTS OF OVEREXPOSURE - CHRONIC HAZARDS:
OVEREXPOSURE TO XYLENE IN LABORATORY ANIMALS HAS BEEN ASSOCIATED WITH
LIVER ABNORMALITIES, KIDNEY, LUNG, SPLEEN, EYE AND BLOOD DAMAGE AS WELL
AS REPRODUCTIVE DISORDERS. EFFECTS IN HUMANS, DUE TO CHRONIC OVEREXPOSURE,
HAVE INCLUDED LIVER, CARDIAC ABNORMALITIES AND NERVOUS SYSTEM DAMAGE.
IARC LISTS ETHYLBENZENE AS A POSSIBLE HUMAN CARCINOGEN (GROUP 2B).
CONTAINS TITANIUM DIOXIDE. TITANIUM DIOXIDE IS LISTED AS A GROUP
2B-"POSSIBLY CARCINOGENIC TO HUMANS" BY IARC. NO SIGNIFICANT EXPOSURE TO
TITANIUM DIOXIDE IS THOUGHT TO OCCUR DURING THE USE OF PRODUCTS IN WHICH
TITANIUM DIOXIDE IS BOUND TO OTHER MATERIALS, SUCH AS IN PAINTS DURING
BRUSH APPLICATION OR DRYING. RISK OF OVEREXPOSURE DEPENDS ON DURATION
AND LEVEL OF EXPOSURE TO DUST FROM REPEATED SANDING OF SURFACES OR SPRAY
MIST AND THE ACTUAL CONCENTRATION OF TITANIUM DIOXIDE IN THE FORMULA. (REF:
IARC MONOGRAPH, VOL. 93, 2010) REPORTS HAVE ASSOCIATED REPEATED AND
PROLONGED OCCUPATIONAL OVEREXPOSURE TO SOLVENTS WITH PERMANENT BRAIN AND
NERVOUS SYSTEM DAMAGE. HIGH CONCENTRATIONS MAY LEAD TO CENTRAL NERVOUS
SYSTEM EFFECTS (DROWSINESS, DIZZINESS, NAUSEA, HEADACHES, PARALYSIS, AND
BLURRED VISION) AND/OR DAMAGE.
PRIMARY ROUTE(S) OF ENTRY:
EYE CONTACT, INGESTION, INHALATION, SKIN ABSORPTION, SKIN CONTACT
ACUTE TOXICITY VALUES:
THE ACUTE EFFECTS OF THIS PRODUCT HAVE NOT BEEN TESTED. DATA ON INDIVIDUAL
COMPONENTS ARE TABULATED BELOW:
CAS-NO. CHEMICAL NAME ORAL LD50 DERMAL LD50 VAPOR LC50
25068-38-6 EPICHLOROHYDRIN- 11400 MG/KG >5000 25 G/L
BISPHENOL A RESIN RAT
14807-96-6 HYDROUS MAGNESIUM 6000 N.E. 30
SILICATE
13463-67-7 TITANIUM DIOXIDE >10000 MG/KG 2500 MG/KG N.E.
RAT
1330-20-7 XYLENES 3500 MG/KG >4350 MG/KG 29.08 MG/L
(O-, M-, P- ISOMERS) RAT RABBIT RAT
108-10-1 METHYL ISOBUTYL 2080 MG/KG 3000 MG/KG 8.2 MG/L
KETONE RAT RABBIT RAT
100-41-4 ETHYLBENZENE 3500 MG/KG 15400 MG/KG 17.4 MG/L
RAT RABBIT RAT
N.E. - NOT ESTABLISHED
| 12. ECOLOGICAL INFORMATION | |
ECOLOGICAL INFORMATION:
PRODUCT IS A MIXTURE OF LISTED COMPONENTS. PRODUCT IS A MIXTURE OF LISTED
COMPONENTS.
| 13. DISPOSAL INFORMATION | |
DISPOSAL INFORMATION:
DISPOSE OF MATERIAL IN ACCORDANCE TO LOCAL, STATE, AND FEDERAL REGULATIONS
AND ORDINANCES. DO NOT ALLOW TO ENTER WATERWAYS, WASTEWATER, SOIL, STORM
DRAINS OR SEWER SYSTEMS. DO NOT INCINERATE CLOSED CONTAINERS.
| 14. TRANSPORT INFORMATION | |
DOMESTIC INTERNATIONAL AIR TDG
(USDOT) (IMDG) (IATA) (CANADA)
UN NUMBER N.A. 1263 1263 N.A.
PROPER SHIPPING NAME PAINT PRODUCTS PAINT PAINT PAINT PRODUCTS
IN LIMITED IN LIMITED
QUANTITIES QUANTITIES
HAZARD CLASS N.A. 3 3 N.A.
PACKING GROUP N.A. III III N.A.
LIMITED QUANTITY YES YES YES YES
| 15. REGULATORY INFORMATION | |
U.S. FEDERAL REGULATIONS:
CERCLA - SARA HAZARD CATEGORY:
THIS PRODUCT HAS BEEN REVIEWED ACCORDING TO THE EPA 'HAZARD CATEGORIES'
PROMULGATED UNDER SECTIONS 311 AND 312 OF THE SUPERFUND AMENDMENT AND
REAUTHORIZATION ACT OF 1986 (SARA TITLE III) AND IS CONSIDERED, UNDER
APPLICABLE DEFINITIONS, TO MEET THE FOLLOWING CATEGORIES:
FLAMMABLE (GASES, AEROSOLS, LIQUIDS, OR SOLIDS), CARCINOGENICITY, SKIN
CORROSION OR IRRITATION, RESPIRATORY OR SKIN SENSITIZATION, SERIOUS EYE
DAMAGE OR EYE IRRITATION, SPECIFIC TARGET ORGAN TOXICITY (SINGLE OR
REPEATED EXPOSURE)
SARA SECTION 313:
THIS PRODUCT CONTAINS THE FOLLOWING SUBSTANCES SUBJECT TO THE REPORTING
REQUIREMENTS OF SECTION 313 OF TITLE III OF THE SUPERFUND AMENDMENT AND
REAUTHORIZATION ACT OF 1986 AND 40 CFR PART 372:
CHEMICAL NAME CAS-NO.
XYLENES (O-, M-, P- ISOMERS) 1330-20-7
METHYL ISOBUTYL KETONE 108-10-1
ETHYLBENZENE 100-41-4
TOXIC SUBSTANCES CONTROL ACT:
THIS PRODUCT CONTAINS THE FOLLOWING CHEMICAL SUBSTANCES SUBJECT TO THE
REPORTING REQUIREMENTS OF TSCA 12(B) IF EXPORTED FROM THE UNITED STATES:
NO TSCA 12(B) COMPONENTS EXIST IN THIS PRODUCT.
| 16. OTHER INFORMATION | |
HMIS RATINGS:
HEALTH 2*
FLAMMABILITY 3
PHYSICAL HAZARD 0
PERSONAL PROTECTION X
NFPA RATINGS:
HEALTH 2
FLAMMABILITY 3
INSTABILITY 0
VOLATILE ORGANIC COMPOUNDS: 226 G/L
SDS REVISION DATE: 8/7/2018
REASON FOR REVISION:
REVISION DESCRIPTION CHANGED
PRODUCT COMPOSITION CHANGED
SUBSTANCE REGULATORY CAS NUMBER CHANGED
SUBSTANCE HAZARDOUS FLAG CHANGED
SUBSTANCE HAZARD THRESHOLD % CHANGED
SUBSTANCE AND/OR PRODUCT PROPERTIES CHANGED IN SECTION(S):
02 - HAZARD IDENTIFICATION
08 - EXPOSURE CONTROLS/PERSONAL PROTECTION
15 - REGULATORY INFORMATION
16 - OTHER INFORMATION
REVISION STATEMENT(S) CHANGED
LEGEND:
N.A. - NOT APPLICABLE
N.E. - NOT ESTABLISHED
N.D. - NOT DETERMINED
THE MANUFACTURER BELIEVES, TO THE BEST OF ITS KNOWLEDGE, INFORMATION AND
BELIEF, THE INFORMATION CONTAINED HEREIN TO BE ACCURATE AND RELIABLE AS OF
THE DATE OF THIS SAFETY DATA SHEET. HOWEVER, BECAUSE THE CONDITIONS OF
HANDLING, USE, AND STORAGE OF THESE MATERIALS ARE BEYOND OUR CONTROL, WE
ASSUME NO RESPONSIBILITY OR LIABILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE INCURRED BY THE USE OF THESE MATERIALS. THE MANUFACTURER MAKES NO
WARRANTY, EXPRESSED OR IMPLIED, REGARDING THE ACCURACY OR RELIABILITY OF
THE DATA OR RESULTS OBTAINED FROM THEIR USE. ALL MATERIALS MAY PRESENT
UNKNOWN HAZARDS AND SHOULD BE USED WITH CAUTION. THE INFORMATION AND
RECOMMENDATIONS IN THIS MATERIAL SAFETY DATA SHEET ARE OFFERED FOR THE
USERS' CONSIDERATION AND EXAMINATION. IT IS THE RESPONSIBILITY OF THE USER
TO DETERMINE THE FINAL SUITABILITY OF THIS INFORMATION AND TO COMPLY WITH
ALL APPLICABLE INTERNATIONAL, FEDERAL, STATE, AND LOCAL LAWS AND
REGULATIONS.