| Common Name: | ABRASIVE PRODUCTS, 341D BELTS |
| Manufacturer: | 3M |
| SDS Revision Date: | 3/14/2014 |
| SDS Format: | GHS-US |
| Item Number(s): | 4ZR52, 6RX76 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M(TM) ABRASIVE PRODUCTS, 341D BELTS
03/14/14
3M
SAFETY DATA SHEET
COPYRIGHT, 2014, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR THE
PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 25-8517-2
VERSION NUMBER: 2.02
ISSUE DATE: 03/14/14
SUPERCEDES DATE: 03/22/13
| SECTION 1: IDENTIFICATION |  |
1.1. PRODUCT IDENTIFIER: 3M(TM) ABRASIVE PRODUCTS, 341D BELTS
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE: ABRASIVE PRODUCT
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: ABRASIVE SYSTEMS DIVISION
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
NOT CLASSIFIED AS HAZARDOUS ACCORDING TO OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
2.2. LABEL ELEMENTS:
SIGNAL WORD: NOT APPLICABLE.
SYMBOLS: NOT APPLICABLE.
PICTOGRAMS: NOT APPLICABLE.
NOTES TO PHYSICIAN: NOT APPLICABLE
2.3. HAZARDS NOT OTHERWISE CLASSIFIED: NONE.
24% OF THE MIXTURE CONSISTS OF INGREDIENTS OF UNKNOWN ACUTE ORAL TOXICITY.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
ALUMINUM OXIDE MINERAL (NON-FIBROUS) 1344-28-1 25 - 50
FILLER 13983-17-0 5 - 15
FILLER 1317-65-3 0.1 - 10
INORGANIC FLUORIDE 15096-52-3 2 - 15
TITANIUM DIOXIDE 13463-67-7 0.5 - 2
CURED RESIN MIXTURE 10 - 25
CLOTH BACKING NONE 5 - 60
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
WASH WITH SOAP AND WATER. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL ATTENTION.
EYE CONTACT:
FLUSH WITH LARGE AMOUNTS OF WATER. REMOVE CONTACT LENSES IF EASY TO DO.
CONTINUE RINSING. IF SIGNS/SYMPTOMS PERSIST, GET MEDICAL ATTENTION.
IF SWALLOWED: NO NEED FOR FIRST AID IS ANTICIPATED.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED: NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
IN CASE OF FIRE:
USE A FIRE FIGHTING AGENT SUITABLE FOR ORDINARY COMBUSTIBLE MATERIAL SUCH
AS WATER OR FOAM TO EXTINGUISH.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
EXPOSURE TO EXTREME HEAT CAN GIVE RISE TO THERMAL DECOMPOSITION.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
HYDROGEN FLUORIDE DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
WHEN FIRE FIGHTING CONDITIONS ARE SEVERE AND TOTAL THERMAL DECOMPOSITION OF
THE PRODUCT IS POSSIBLE, WEAR FULL PROTECTIVE CLOTHING, INCLUDING HELMET,
SELF-CONTAINED, POSITIVE PRESSURE OR PRESSURE DEMAND BREATHING APPARATUS,
BUNKER COAT AND PANTS, BANDS AROUND ARMS, WAIST AND LEGS, FACE MASK, AND
PROTECTIVE COVERING FOR EXPOSED AREAS OF THE HEAD.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
OBSERVE PRECAUTIONS FROM OTHER SECTIONS.
6.2. ENVIRONMENTAL PRECAUTIONS: AVOID RELEASE TO THE ENVIRONMENT.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP: NOT APPLICABLE.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
DO NOT BREATHE THERMAL DECOMPOSITION PRODUCTS. FOR INDUSTRIAL OR
PROFESSIONAL USE ONLY. DO NOT USE IN A CONFINED AREA WITH MINIMAL AIR
EXCHANGE. AVOID BREATHING OF DUST CREATED BY SANDING, GRINDING OR
MACHINING. DAMAGED PRODUCT CAN BREAK APART DURING USE AND CAUSE SERIOUS
INJURY TO FACE OR EYES. CHECK PRODUCT FOR DAMAGE SUCH AS CRACKS OR NICKS
PRIOR TO USE. REPLACE IF DAMAGED. ALWAYS WEAR EYE AND FACE PROTECTION WHEN
WORKING AT SANDING OR GRINDING OPERATIONS OR WHEN NEAR SUCH OPERATIONS.
AVOID RELEASE TO THE ENVIRONMENT. COMBUSTIBLE DUST MAY FORM BY ACTION OF
THIS PRODUCT ON ANOTHER MATERIAL (SUBSTRATE). DUST GENERATED FROM THE
SUBSTRATE DURING USE OF THIS PRODUCT MAY BE EXPLOSIVE IF IN SUFFICIENT
CONCENTRATION WITH AN IGNITION SOURCE. DUST DEPOSITS SHOULD NOT BE ALLOWED
TO ACCUMULATE ON SURFACES BECAUSE OF THE POTENTIAL FOR SECONDARY
EXPLOSIONS.
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
NO SPECIAL STORAGE REQUIREMENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
INGREDIENT C.A.S. NO. AGENCY LIMIT TYPE ADDITIONAL
COMMENTS
FILLER 1317-65-3 US DEPT OF TWA (AS TOTAL
LABOR - OSHA DUST): 15 MG/M3
TWA (RESPIRABLE
FRACTION):
5 MG/M3
ALUMINUM OXIDE 1344-28-1 CHEMICAL TWA: 1 FIBER/CC
MINERAL (NON- MANUFACTURER
FIBROUS) REC GUID
ALUMINUM OXIDE 1344-28-1 US DEPT OF TWA (AS TOTAL
MINERAL (NON- LABOR - OSHA DUST): 15 MG/M3
FIBROUS)
TWA (RESPIRABLE
FRACTION):
5 MG/M3
ALUMINUM, 1344-28-1 AMER CONF OF TWA (RESPIRABLE
INSOLUBLE GOV. INDUST. FRACTION):
COMPOUNDS HYG. 1 MG/M3
TITANIUM DIOXIDE 13463-67-7 AMER CONF OF TWA: 10 MG/M3
GOV. INDUST.
HYG.
TITANIUM DIOXIDE 13463-67-7 CHEMICAL TWA (AS
MANUFACTURER RESPIRABLE DUST):
REC GUID 5 MG/M3
TITANIUM DIOXIDE 13463-67-7 US DEPT OF TWA (AS TOTAL
LABOR - OSHA DUST): 15 MG/M3
ALUMINUM, 15096-52-3 AMER CONF OF TWA (RESPIRABLE
INSOLUBLE GOV. INDUST. FRACTION):
COMPOUNDS HYG. 1 MG/M3
FLUORIDES 15096-52-3 AMER CONF OF TWA (AS F):
GOV. INDUST. 2.5 MG/M3
HYG.
FLUORIDES 15096-52-3 US DEPT OF TWA (AS DUST):
LABOR - OSHA 2.5 MG/M3
TWA (AS F):
2.5 MG/M3
AMER CONF OF GOV. INDUST. HYG.:
AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
AMERICAN INDUST. HYGIENE ASSOC: AMERICAN INDUSTRIAL HYGIENE ASSOCIATION
CHEMICAL MANUFACTURER REC GUID:
CHEMICAL MANUFACTURER'S RECOMMENDED GUIDELINES
US DEPT OF LABOR - OSHA:
UNITED STATES DEPARTMENT OF LABOR - OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION
TWA: TIME-WEIGHTED-AVERAGE
STEL: SHORT TERM EXPOSURE LIMIT
CEIL: CEILING
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
FOR THOSE SITUATIONS WHERE THE MATERIAL MIGHT BE EXPOSED TO EXTREME
OVERHEATING DUE TO MISUSE OR EQUIPMENT FAILURE, USE WITH APPROPRIATE LOCAL
EXHAUST VENTILATION SUFFICIENT TO MAINTAIN LEVELS OF THERMAL DECOMPOSITION
PRODUCTS BELOW THEIR EXPOSURE GUIDELINES. PROVIDE APPROPRIATE LOCAL EXHAUST
VENTILATION FOR SANDING, GRINDING OR MACHINING. USE GENERAL DILUTION
VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO CONTROL AIRBORNE EXPOSURES
TO BELOW RELEVANT EXPOSURE LIMITS AND/OR CONTROL
DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS NOT ADEQUATE, USE
RESPIRATORY PROTECTION EQUIPMENT. PROVIDE LOCAL EXHAUST AT PROCESS EMISSION
SOURCES TO CONTROL EXPOSURE NEAR THE SOURCE AND TO PREVENT THE ESCAPE OF
DUST INTO THE WORK AREA. ENSURE THAT DUST-HANDLING SYSTEMS (SUCH AS EXHAUST
DUCTS, DUST COLLECTORS, VESSELS, AND PROCESSING EQUIPMENT) ARE DESIGNED IN
A MANNER TO PREVENT THE ESCAPE OF DUST INTO THE WORK AREA (I.E., THERE IS
NO LEAKAGE FROM THE EQUIPMENT).
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
TO MINIMIZE THE RISK OF INJURY TO FACE AND EYES, ALWAYS WEAR EYE AND FACE
PROTECTION WHEN WORKING AT SANDING OR GRINDING OPERATIONS OR WHEN NEAR SUCH
OPERATIONS. SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON
THE RESULTS OF AN EXPOSURE ASSESSMENT. THE FOLLOWING EYE/FACE PROTECTION(S)
ARE RECOMMENDED: SAFETY GLASSES WITH SIDE SHIELDS
SKIN/HAND PROTECTION:
WEAR APPROPRIATE GLOVES TO MINIMIZE RISK OF INJURY TO SKIN FROM CONTACT
WITH DUST OR PHYSICAL ABRASION FROM GRINDING OR SANDING.
RESPIRATORY PROTECTION:
ASSESS EXPOSURE CONCENTRATIONS OF ALL MATERIALS INVOLVED IN THE WORK
PROCESS. CONSIDER MATERIAL BEING ABRADED WHEN DETERMINING THE APPROPRIATE
RESPIRATORY PROTECTION. SELECT AND USE APPROPRIATE RESPIRATORS TO PREVENT
INHALATION OVEREXPOSURE. AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF
A RESPIRATOR IS REQUIRED. IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS
PART OF A FULL RESPIRATORY PROTECTION PROGRAM. BASED ON THE RESULTS OF THE
EXPOSURE ASSESSMENT, SELECT FROM THE FOLLOWING RESPIRATOR TYPE(S) TO REDUCE
INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
PARTICULATES
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: SOLID
ODOR, COLOR, GRADE: SOLID ABRASIVE PRODUCT
ODOR THRESHOLD: NOT APPLICABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: NOT APPLICABLE
FLASH POINT: NOT APPLICABLE
EVAPORATION RATE: NOT APPLICABLE
FLAMMABILITY (SOLID, GAS): NOT CLASSIFIED
FLAMMABLE LIMITS (LEL): NOT APPLICABLE
FLAMMABLE LIMITS (UEL): NOT APPLICABLE
VAPOR PRESSURE: NOT APPLICABLE
VAPOR DENSITY: NOT APPLICABLE
SPECIFIC GRAVITY: NOT APPLICABLE
SOLUBILITY IN WATER: NOT APPLICABLE
SOLUBILITY- NON-WATER: NOT APPLICABLE
AUTOIGNITION TEMPERATURE: NOT APPLICABLE
DECOMPOSITION TEMPERATURE: NOT APPLICABLE
VISCOSITY: NOT APPLICABLE
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL IS CONSIDERED TO BE NON REACTIVE UNDER NORMAL USE CONDITIONS.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID: NONE KNOWN.
10.5. INCOMPATIBLE MATERIALS: NONE KNOWN.
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
IF THE PRODUCT IS EXPOSED TO EXTREME CONDITION OF HEAT FROM MISUSE OR
EQUIPMENT FAILURE, TOXIC DECOMPOSITION PRODUCTS THAT INCLUDE HYDROGEN
FLUORIDE AND PERFLUOROISOBUTYLENE CAN OCCUR. EXTREME HEAT ARISING FROM
SITUATIONS SUCH AS MISUSE OR EQUIPMENT FAILURE CAN GENERATE HYDROGEN
FLUORIDE AS A DECOMPOSITION PRODUCT.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR THE
SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT BELOW
THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
DUST FROM GRINDING, SANDING OR MACHINING MAY CAUSE IRRITATION OF THE
RESPIRATORY SYSTEM. SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL
DISCHARGE, HEADACHE, HOARSENESS, AND NOSE AND THROAT PAIN.
SKIN CONTACT:
MECHANICAL SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABRASION, REDNESS, PAIN, AND ITCHING.
EYE CONTACT:
MECHANICAL EYE IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE PAIN, REDNESS, TEARING AND CORNEAL ABRASION.
DUST CREATED BY GRINDING, SANDING, OR MACHINING MAY CAUSE EYE IRRITATION.
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND BLURRED OR
HAZY VISION.
INGESTION: NO HEALTH EFFECTS ARE EXPECTED.
CARCINOGENICITY:
INGREDIENT C.A.S. NO. CLASS DESCRIPTION REGULATION
TITANIUM DIOXIDE 13463-67-7 GRP. 2B: INTERNATIONAL AGENCY
POSSIBLE HUMAN CARC. FOR RESEARCH ON CANCER
ADDITIONAL INFORMATION:
THIS DOCUMENT COVERS ONLY THE 3M PRODUCT. FOR COMPLETE ASSESSMENT, WHEN
DETERMINING THE DEGREE OF HAZARD, THE MATERIAL BEING ABRADED MUST ALSO BE
CONSIDERED.
THIS PRODUCT CONTAINS TITANIUM DIOXIDE. CANCER OF THE LUNGS HAS BEEN
OBSERVED IN RATS THAT INHALED HIGH LEVELS OF TITANIUM DIOXIDE. NO EXPOSURE
TO INHALED TITANIUM DIOXIDE IS EXPECTED DURING THE NORMAL HANDLING AND USE
OF THIS PRODUCT. TITANIUM DIOXIDE WAS NOT DETECTED WHEN AIR SAMPLING WAS
CONDUCTED DURING SIMULATED USE OF SIMILAR PRODUCTS CONTAINING TITANIUM
DIOXIDE. THEREFORE, THE HEALTH EFFECTS ASSOCIATED WITH TITANIUM DIOXIDE ARE
NOT EXPECTED DURING THE NORMAL USE OF THIS PRODUCT.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT INGESTION NO DATA AVAILABLE;
CALCULATED ATE:
>5,000 MG/KG
ALUMINUM OXIDE MINERAL DERMAL LD50:
(NON-FIBROUS) ESTIMATED TO BE
>5,000 MG/KG
ALUMINUM OXIDE MINERAL INHALATION- RAT LC50: >2.3 MG/L
(NON-FIBROUS) DUST/MIST
(4 HOURS)
ALUMINUM OXIDE MINERAL INGESTION RAT LD50: >5,000 MG/KG
(NON-FIBROUS)
FILLER DERMAL LD50:
ESTIMATED TO BE
>5,000 MG/KG
FILLER INGESTION LD50:
ESTIMATED TO BE
2,000 - 5,000 MG/KG
INORGANIC FLUORIDE DERMAL RABBIT LD50: >2,100 MG/KG
INORGANIC FLUORIDE INHALATION- RAT LC50: 4.5 MG/L
DUST/MIST
(4 HOURS)
INORGANIC FLUORIDE INGESTION RAT LD50: 5,000 MG/KG
TITANIUM DIOXIDE DERMAL RABBIT LD50: >10,000 MG/KG
TITANIUM DIOXIDE INHALATION- RAT LC50: >6.82 MG/L
DUST/MIST
(4 HOURS)
TITANIUM DIOXIDE INGESTION RAT LD50: >10,000 MG/KG
FILLER DERMAL RAT LD50: >2,000 MG/KG
FILLER INHALATION- RAT LC50: 3.0 MG/L
DUST/MIST
(4 HOURS)
FILLER INGESTION RAT LD50: 6,450 MG/KG
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
ALUMINUM OXIDE MINERAL RABBIT NO SIGNIFICANT IRRITATION
(NON-FIBROUS)
INORGANIC FLUORIDE MINIMAL IRRITATION
TITANIUM DIOXIDE RABBIT NO SIGNIFICANT IRRITATION
FILLER RABBIT NO SIGNIFICANT IRRITATION
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
ALUMINUM OXIDE MINERAL RABBIT NO SIGNIFICANT IRRITATION
(NON-FIBROUS)
INORGANIC FLUORIDE MODERATE IRRITANT
TITANIUM DIOXIDE RABBIT NO SIGNIFICANT IRRITATION
FILLER RABBIT NO SIGNIFICANT IRRITATION
SKIN SENSITIZATION:
NAME SPECIES VALUE
TITANIUM DIOXIDE HUMAN NOT SENSITIZING
AND
ANIMAL
RESPIRATORY SENSITIZATION:
NAME SPECIES VALUE
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
ALUMINUM OXIDE MINERAL IN VITRO NOT MUTAGENIC
(NON-FIBROUS)
FILLER IN VITRO NOT MUTAGENIC
TITANIUM DIOXIDE IN VITRO NOT MUTAGENIC
TITANIUM DIOXIDE IN VIVO NOT MUTAGENIC
CARCINOGENICITY:
NAME ROUTE SPECIES VALUE
ALUMINUM OXIDE MINERAL INHALATION RAT NOT CARCINOGENIC
(NON-FIBROUS)
TITANIUM DIOXIDE INGESTION MULTIPLE NOT CARCINOGENIC
ANIMAL
SPECIES
TITANIUM DIOXIDE INHALATION RAT CARCINOGENIC
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
NAME ROUTE VALUE
FILLER INGESTION NOT TOXIC TO DEVELOPMENT
NAME SPECIES TEST RESULT EXPOSURE DURATION
FILLER RAT NOAEL: 625 MG/KG/DAY PREMATING & DURING
GESTATION
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
FILLER INHALATION RESPIRATORY SYSTEM ALL DATA ARE NEGATIVE
NAME SPECIES TEST RESULT EXPOSURE DURATION
FILLER RAT NOAEL: 0.812 MG/L 90 MINUTES
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
ALUMINUM OXIDE INHALATION PNEUMOCONIOSIS SOME POSITIVE DATA
MINERAL (NON-FIBROUS) PULMONARY FIBROSIS EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
FILLER INHALATION RESPIRATORY SYSTEM SOME POSITIVE DATA
EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
FILLER INHALATION PULMONARY FIBROSIS ALL DATA ARE
NEGATIVE
INORGANIC FLUORIDE INHALATION BONE, TEETH, NAILS, SOME POSITIVE DATA
AND/OR HAIR EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
TITANIUM DIOXIDE INHALATION RESPIRATORY SYSTEM SOME POSITIVE DATA
EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
TITANIUM DIOXIDE INHALATION PULMONARY FIBROSIS ALL DATA ARE
NEGATIVE
FILLER INHALATION RESPIRATORY SYSTEM SOME POSITIVE DATA
EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
NAME SPECIES TEST RESULT EXPOSURE DURATION
ALUMINUM OXIDE HUMAN NOAEL: NOT AVAILABLE OCCUPATIONAL
MINERAL EXPOSURE
(NON-FIBROUS)
FILLER HUMAN NOAEL: NOT AVAILABLE OCCUPATIONAL
EXPOSURE
FILLER HUMAN NOAEL: NOT AVAILABLE
AND
ANIMAL
INORGANIC HHA
FLUORIDE
TITANIUM DIOXIDE RAT LOAEL: 0.010 MG/L 2 YEARS
TITANIUM DIOXIDE HUMAN NOAEL: NOT AVAILABLE OCCUPATIONAL
EXPOSURE
FILLER HUMAN NOAEL: NOT AVAILABLE OCCUPATIONAL
EXPOSURE
ASPIRATION HAZARD:
NAME VALUE
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/ CONTAINER IN ACCORDANCE WITH THE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
THE SUBSTRATE THAT WAS ABRADED MUST BE CONSIDERED AS A FACTOR IN THE
DISPOSAL METHOD FOR THIS PRODUCT. DISPOSE OF WASTE PRODUCT IN A PERMITTED
INDUSTRIAL WASTE FACILITY. AS A DISPOSAL ALTERNATIVE, INCINERATE IN A
PERMITTED WASTE INCINERATION FACILITY. PROPER DESTRUCTION MAY REQUIRE THE
USE OF ADDITIONAL FUEL DURING INCINERATION PROCESSES. COMBUSTION PRODUCTS
WILL INCLUDE HALOGEN ACID (HCL/HF/HBR). FACILITY MUST BE CAPABLE OF
HANDLING HALOGENATED MATERIALS.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
| SECTION 14: TRANSPORT INFORMATION | |
NOT REGULATED PER U.S. DOT, IATA OR IMO.
THESE TRANSPORTATION CLASSIFICATIONS ARE PROVIDED AS A CUSTOMER SERVICE. AS
THE SHIPPER YOU REMAIN RESPONSIBLE FOR COMPLYING WITH ALL APPLICABLE LAWS
AND REGULATIONS, INCLUDING PROPER TRANSPORTATION CLASSIFICATION AND
PACKAGING. 3M TRANSPORTATION CLASSIFICATIONS ARE BASED ON PRODUCT
FORMULATION, PACKAGING, 3M POLICIES AND 3M UNDERSTANDING OF APPLICABLE
CURRENT REGULATIONS. 3M DOES NOT GUARANTEE THE ACCURACY OF THIS
CLASSIFICATION INFORMATION. THIS INFORMATION APPLIES ONLY TO TRANSPORTATION
CLASSIFICATION AND NOT THE PACKAGING, LABELING, OR MARKING REQUIREMENTS.
THE ORIGINAL 3M PACKAGE IS CERTIFIED FOR U.S. GROUND SHIPMENT ONLY. IF YOU
ARE SHIPPING BY AIR OR OCEAN, THE PACKAGE MAY NOT MEET APPLICABLE
REGULATORY REQUIREMENTS.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
311/312 HAZARD CATEGORIES:
FIRE HAZARD: NO
PRESSURE HAZARD: NO
REACTIVITY HAZARD: NO
IMMEDIATE HAZARD: NO
DELAYED HAZARD: NO
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
15.3. CHEMICAL INVENTORIES:
THIS PRODUCT IS AN ARTICLE AS DEFINED BY TSCA REGULATIONS, AND IS EXEMPT
FROM TSCA INVENTORY LISTING REQUIREMENTS.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 0
FLAMMABILITY 1
INSTABILITY 0
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED FOR
USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO INCLUDE
THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT ARE KNOWN
TO BE GENERATED IN SIGNIFICANT QUANTITIES.
HMIS HAZARD CLASSIFICATION:
HEALTH 0
FLAMMABILITY 1
PHYSICAL HAZARD 0
PERSONAL PROTECTION X - SEE PPE SECTION.
HAZARDOUS MATERIAL IDENTIFICATION SYSTEM (HMIS(R*) III) HAZARD RATINGS ARE
DESIGNED TO INFORM EMPLOYEES OF CHEMICAL HAZARDS IN THE WORKPLACE. THESE
RATINGS ARE BASED ON THE INHERENT PROPERTIES OF THE MATERIAL UNDER EXPECTED
CONDITIONS OF NORMAL USE AND ARE NOT INTENDED FOR USE IN EMERGENCY
SITUATIONS. HMIS(R*) III RATINGS ARE TO BE USED WITH A FULLY IMPLEMENTED
HMIS(R*) III PROGRAM. HMIS(R*) IS A REGISTERED MARK OF THE AMERICAN
COATINGS ASSOCIATION (ACA).
DOCUMENT GROUP: 25-8517-2
VERSION NUMBER: 2.02
ISSUE DATE: 03/14/14
SUPERCEDES DATE: 03/22/13
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED IN
ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM