| Common Name: | SCOTCH-WELD LOW ODOR ACRYLIC ADHESIVE DP8825NS GREEN, PART A |
| Manufacturer: | 3M |
| SDS Revision Date: | 3/3/2016 |
| SDS Format: | GHS-US |
| Item Number(s): | 6TF61 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M(TM) SCOTCH-WELD(TM) LOW ODOR ACRYLIC ADHESIVE DP8825NS GREEN, PART A
03/03/16
3M
SAFETY DATA SHEET
COPYRIGHT, 2016, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR
THE PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 33-2640-2
VERSION NUMBER: 1.03
ISSUE DATE: 03/03/16
SUPERCEDES DATE: 10/15/14
| SECTION 1: IDENTIFICATION |  |
1.1. PRODUCT IDENTIFIER:
3M(TM) SCOTCH-WELD(TM) LOW ODOR ACRYLIC ADHESIVE DP8825NS GREEN, PART A
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE: STRUCTURAL ADHESIVE
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: INDUSTRIAL ADHESIVES AND TAPES DIVISION
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
SKIN SENSITIZER: CATEGORY 1B.
2.2. LABEL ELEMENTS:
SIGNAL WORD: WARNING
SYMBOLS: EXCLAMATION MARK
PICTOGRAMS: EXCLAMATION MARK
HAZARD STATEMENTS: MAY CAUSE AN ALLERGIC SKIN REACTION.
PRECAUTIONARY STATEMENTS:
PREVENTION:
AVOID BREATHING DUST/FUME/GAS/MIST/VAPORS/SPRAY.
WEAR PROTECTIVE GLOVES.
CONTAMINATED WORK CLOTHING MUST NOT BE ALLOWED OUT OF THE WORKPLACE.
RESPONSE:
IF ON SKIN: WASH WITH PLENTY OF SOAP AND WATER.
IF SKIN IRRITATION OR RASH OCCURS: GET MEDICAL ADVICE/ATTENTION.
WASH CONTAMINATED CLOTHING BEFORE REUSE.
DISPOSAL:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH APPLICABLE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
2.3. HAZARDS NOT OTHERWISE CLASSIFIED: NONE.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
DIBENZOATE PROPANOL 27138-31-4 50 - 80 TRADE SECRET *
ACRYLATE POLYMER 25101-28-4 5 - 30 TRADE SECRET *
CATALYST TRADE SECRET* 1 - 20 TRADE SECRET *
(NJTS REG. NO. 04499600-6922)
ORGANIC PEROXIDE 13122-18-4 1 - 10 TRADE SECRET *
NJTS OR NJTSRN: NEW JERSEY TRADE SECRET REGISTRY NUMBER.
*THE SPECIFIC CHEMICAL IDENTITY AND/OR EXACT PERCENTAGE (CONCENTRATION)
OF THIS COMPOSITION HAS BEEN WITHHELD AS A TRADE SECRET.
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
IMMEDIATELY WASH WITH SOAP AND WATER. REMOVE CONTAMINATED CLOTHING AND
WASH BEFORE REUSE. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL ATTENTION.
EYE CONTACT:
FLUSH WITH LARGE AMOUNTS OF WATER. REMOVE CONTACT LENSES IF EASY TO DO.
CONTINUE RINSING. IF SIGNS/SYMPTOMS PERSIST, GET MEDICAL ATTENTION.
IF SWALLOWED: RINSE MOUTH. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED: NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
IN CASE OF FIRE:
USE A FIRE FIGHTING AGENT SUITABLE FOR ORDINARY COMBUSTIBLE MATERIAL SUCH
AS WATER OR FOAM TO EXTINGUISH.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
NONE INHERENT IN THIS PRODUCT.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
NO SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS ARE ANTICIPATED.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
EVACUATE AREA. VENTILATE THE AREA WITH FRESH AIR. FOR LARGE SPILL, OR
SPILLS IN CONFINED SPACES, PROVIDE MECHANICAL VENTILATION TO DISPERSE OR
EXHAUST VAPORS, IN ACCORDANCE WITH GOOD INDUSTRIAL HYGIENE PRACTICE. REFER
TO OTHER SECTIONS OF THIS SDS FOR INFORMATION REGARDING PHYSICAL AND
HEALTH HAZARDS, RESPIRATORY PROTECTION, VENTILATION, AND PERSONAL
PROTECTIVE EQUIPMENT.
6.2. ENVIRONMENTAL PRECAUTIONS: AVOID RELEASE TO THE ENVIRONMENT.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP:
CONTAIN SPILL. WORKING FROM AROUND THE EDGES OF THE SPILL INWARD, COVER
WITH BENTONITE, VERMICULITE, OR COMMERCIALLY AVAILABLE INORGANIC ABSORBENT
MATERIAL. MIX IN SUFFICIENT ABSORBENT UNTIL IT APPEARS DRY. REMEMBER,
ADDING AN ABSORBENT MATERIAL DOES NOT REMOVE A PHYSICAL, HEALTH, OR
ENVIRONMENTAL HAZARD. COLLECT AS MUCH OF THE SPILLED MATERIAL AS POSSIBLE.
PLACE IN A CLOSED CONTAINER APPROVED FOR TRANSPORTATION BY APPROPRIATE
AUTHORITIES. CLEAN UP RESIDUE WITH AN APPROPRIATE SOLVENT SELECTED BY A
QUALIFIED AND AUTHORIZED PERSON. VENTILATE THE AREA WITH FRESH AIR. READ
AND FOLLOW SAFETY PRECAUTIONS ON THE SOLVENT LABEL AND SDS. SEAL THE
CONTAINER. DISPOSE OF COLLECTED MATERIAL AS SOON AS POSSIBLE.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
AVOID BREATHING DUST/FUME/GAS/MIST/VAPORS/SPRAY. DO NOT GET IN EYES, ON
SKIN, OR ON CLOTHING. DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT.
WASH THOROUGHLY AFTER HANDLING. CONTAMINATED WORK CLOTHING SHOULD NOT BE
ALLOWED OUT OF THE WORKPLACE. AVOID RELEASE TO THE ENVIRONMENT. WASH
CONTAMINATED CLOTHING BEFORE REUSE. AVOID CONTACT WITH OXIDIZING AGENTS
(EG. CHLORINE, CHROMIC ACID ETC.)
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
STORE AWAY FROM HEAT. STORE AWAY FROM ACIDS. STORE AWAY FROM STRONG BASES.
STORE AWAY FROM OXIDIZING AGENTS. STORE AWAY FROM AMINES.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
NO OCCUPATIONAL EXPOSURE LIMIT VALUES EXIST FOR ANY OF THE COMPONENTS
LISTED IN SECTION 3 OF THIS SDS.
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO
CONTROL AIRBORNE EXPOSURES TO BELOW RELEVANT EXPOSURE LIMITS AND/OR CONTROL
DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS NOT ADEQUATE, USE
RESPIRATORY PROTECTION EQUIPMENT.
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON THE RESULTS
OF AN EXPOSURE ASSESSMENT.
THE FOLLOWING EYE/FACE PROTECTION(S) ARE RECOMMENDED:
SAFETY GLASSES WITH SIDE SHIELDS
SKIN/HAND PROTECTION:
SELECT AND USE GLOVES AND/OR PROTECTIVE CLOTHING APPROVED TO RELEVANT
LOCAL STANDARDS TO PREVENT SKIN CONTACT BASED ON THE RESULTS OF AN
EXPOSURE ASSESSMENT. SELECTION SHOULD BE BASED ON USE FACTORS SUCH AS
EXPOSURE LEVELS, CONCENTRATION OF THE SUBSTANCE OR MIXTURE, FREQUENCY
AND DURATION, PHYSICAL CHALLENGES SUCH AS TEMPERATURE EXTREMES, AND OTHER
USE CONDITIONS. CONSULT WITH YOUR GLOVE AND/OR PROTECTIVE CLOTHING
MANUFACTURER FOR SELECTION OF APPROPRIATE COMPATIBLE GLOVES/PROTECTIVE
CLOTHING.
NOTE:
NITRILE GLOVES MAY BE WORN OVER POLYMER LAMINATE GLOVES TO IMPROVE
DEXTERITY.
GLOVES MADE FROM THE FOLLOWING MATERIAL(S) ARE RECOMMENDED:
POLYMER LAMINATE
RESPIRATORY PROTECTION:
AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF A RESPIRATOR IS REQUIRED.
IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS PART OF A FULL RESPIRATORY
PROTECTION PROGRAM.
BASED ON THE RESULTS OF THE EXPOSURE ASSESSMENT, SELECT FROM THE FOLLOWING
RESPIRATOR TYPE(S) TO REDUCE INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
ORGANIC VAPORS AND PARTICULATES
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: LIQUID
SPECIFIC PHYSICAL FORM: PASTE
ODOR, COLOR, GRADE: BLUE, HYDROCARBON ODOR
ODOR THRESHOLD: NO DATA AVAILABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: >=150 DEG. F
FLASH POINT: >200 DEG. F [TEST METHOD: CLOSED CUP]
EVAPORATION RATE: NO DATA AVAILABLE
FLAMMABILITY (SOLID, GAS): NOT APPLICABLE
FLAMMABLE LIMITS (LEL): NO DATA AVAILABLE
FLAMMABLE LIMITS (UEL): NO DATA AVAILABLE
VAPOR PRESSURE: NO DATA AVAILABLE
DENSITY: 1.08 G/ML
SPECIFIC GRAVITY: 1.08 [REF STD: WATER=1]
SOLUBILITY IN WATER: NIL
SOLUBILITY-NON-WATER: NO DATA AVAILABLE
PARTITION COEFFICIENT N-OCTANOL/WATER: NO DATA AVAILABLE
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
DECOMPOSITION TEMPERATURE: NO DATA AVAILABLE
VISCOSITY: 20,000 CENTIPOISE
HAZARDOUS AIR POLLUTANTS: 0% WEIGHT
VOC LESS H2O & EXEMPT SOLVENTS:
4.8 G/L [DETAILS: WHEN USED AS INTENDED WITH PART B]
VOC LESS H2O & EXEMPT SOLVENTS:
0.5% [DETAILS: WHEN USED AS INTENDED WITH PART B]
VOC LESS H2O & EXEMPT SOLVENTS: 59.4 G/L [DETAILS: AS SUPPLIED]
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL MAY BE REACTIVE WITH CERTAIN AGENTS UNDER CERTAIN
CONDITIONS - SEE THE REMAINING HEADINGS IN THIS SECTION.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID:
HEAT
SPARKS AND/OR FLAMES
10.5. INCOMPATIBLE MATERIALS:
AMINES
STRONG ACIDS
STRONG BASES
STRONG OXIDIZING AGENTS
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR THE
SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT BELOW
THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
THIS PRODUCT MAY HAVE A CHARACTERISTIC ODOR; HOWEVER, NO ADVERSE HEALTH
EFFECTS ARE ANTICIPATED.
SKIN CONTACT:
CONTACT WITH THE SKIN DURING PRODUCT USE IS NOT EXPECTED TO RESULT IN
SIGNIFICANT IRRITATION.
ALLERGIC SKIN REACTION (NON-PHOTO INDUCED):
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, BLISTERING, AND ITCHING.
EYE CONTACT:
CONTACT WITH THE EYES DURING PRODUCT USE IS NOT EXPECTED TO RESULT IN
SIGNIFICANT IRRITATION.
INGESTION: MAY BE HARMFUL IF SWALLOWED.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT INGESTION NO DATA AVAILABLE;
CALCULATED ATE:
2,000 - 5,000 MG/KG
DIBENZOATE PROPANOL DERMAL RAT LD50: >2,000 MG/KG
DIBENZOATE PROPANOL INHALATION- RAT LC50: >200 MG/L
DUST/MIST
(4 HOURS)
DIBENZOATE PROPANOL INGESTION RAT LD50: 3,295 MG/KG
ACRYLATE POLYMER DERMAL LD50:
ESTIMATED TO BE
>5,000 MG/KG
ACRYLATE POLYMER INGESTION RAT LD50: >5,000 MG/KG
CATALYST (NJTS REG. DERMAL PROFESSIONAL LD50:
(NJTS REG. NO. JUDGEMENT ESTIMATED TO BE
NO. 04499600-6922) 2,000 - 5,000 MG/KG
CATALYST (NJTS REG. INGESTION RAT LD50: >2,000 MG/KG
NO. 04499600-6922)
ORGANIC PEROXIDE DERMAL RAT LD50: >2,000 MG/KG
ORGANIC PEROXIDE INHALATION- RAT LC50: >0.8 MG/L
DUST/MIST
(4 HOURS)
ORGANIC PEROXIDE INGESTION RAT LD50: 12,905 MG/KG
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
DIBENZOATE PROPANOL RABBIT NO SIGNIFICANT IRRITATION
ORGANIC PEROXIDE RABBIT NO SIGNIFICANT IRRITATION
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
DIBENZOATE PROPANOL RABBIT NO SIGNIFICANT IRRITATION
ORGANIC PEROXIDE RABBIT NO SIGNIFICANT IRRITATION
SKIN SENSITIZATION:
NAME SPECIES VALUE
DIBENZOATE PROPANOL GUINEA PIG NOT SENSITIZING
CATALYST (NJTS REG. NO. 04499600-6922) MOUSE NOT SENSITIZING
ORGANIC PEROXIDE GUINEA PIG SENSITIZING
RESPIRATORY SENSITIZATION:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
DIBENZOATE PROPANOL IN VITRO NOT MUTAGENIC
CATALYST (NJTS REG. NO. 04499600-6922) IN VITRO NOT MUTAGENIC
CARCINOGENICITY:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
NAME ROUTE VALUE
DIBENZOATE PROPANOL INGESTION NOT TOXIC TO FEMALE REPRODUCTION
DIBENZOATE PROPANOL INGESTION NOT TOXIC TO MALE REPRODUCTION
DIBENZOATE PROPANOL INGESTION SOME POSITIVE DEVELOPMENTAL DATA
EXIST, BUT THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION
NAME SPECIES TEST RESULT EXPOSURE DURATION
DIBENZOATE PROPANOL RAT NOAEL: 2 GENERATION
500 MG/KG/DAY
DIBENZOATE PROPANOL RAT NOAEL: 2 GENERATION
400 MG/KG/DAY
DIBENZOATE PROPANOL RAT NOAEL: DURING GESTATION
1,000 MG/KG/DAY
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
CATALYST (NJTS REG. INGESTION NERVOUS SYSTEM SOME POSITIVE DATA
NO. 04499600-6922) EXIST, BUT THE DATA
ARE NOT SUFFICIENT
FOR CLASSIFICATION
NAME SPECIES TEST RESULT EXPOSURE DURATION
CATALYST RAT NOAEL:
(NJTS REG. NO. 04499600-6922) 2,000 MG/KG
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
DIBENZOATE PROPANOL INGESTION HEMATOPOIETIC SOME POSITIVE DATA
SYSTEM EXIST, BUT THE DATA
LIVER ARE NOT SUFFICIENT
FOR CLASSIFICATION
NAME SPECIES TEST RESULT EXPOSURE DURATION
DIBENZOATE PROPANOL RAT NOAEL: 90 DAYS
2,500 MG/KG/DAY
ASPIRATION HAZARD:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH THE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
DISPOSE OF COMPLETELY CURED (OR POLYMERIZED) MATERIAL IN A PERMITTED
INDUSTRIAL WASTE FACILITY. AS A DISPOSAL ALTERNATIVE, INCINERATE UNCURED
PRODUCT IN A PERMITTED WASTE INCINERATION FACILITY. PROPER DESTRUCTION MAY
REQUIRE THE USE OF ADDITIONAL FUEL DURING INCINERATION PROCESSES. EMPTY
DRUMS/BARRELS/CONTAINERS USED FOR TRANSPORTING AND HANDLING HAZARDOUS
CHEMICALS (CHEMICAL SUBSTANCES/MIXTURES/PREPARATIONS CLASSIFIED AS
HAZARDOUS AS PER APPLICABLE REGULATIONS) SHALL BE CONSIDERED, STORED,
TREATED & DISPOSED OF AS HAZARDOUS WASTES UNLESS OTHERWISE DEFINED BY
APPLICABLE WASTE REGULATIONS. CONSULT WITH THE RESPECTIVE REGULATING
AUTHORITIES TO DETERMINE THE AVAILABLE TREATMENT AND DISPOSAL FACILITIES.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
| SECTION 14: TRANSPORT INFORMATION | |
FOR TRANSPORT INFORMATION, PLEASE VISIT:
HTTP://3M.COM/TRANSPORTINFO OR CALL 1-800-364-3577 OR 651-737-6501.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
311/312 HAZARD CATEGORIES:
FIRE HAZARD: NO
PRESSURE HAZARD: NO
REACTIVITY HAZARD: NO
IMMEDIATE HAZARD: YES
DELAYED HAZARD: NO
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
15.3. CHEMICAL INVENTORIES:
THE COMPONENTS OF THIS PRODUCT ARE IN COMPLIANCE WITH THE CHEMICAL
NOTIFICATION REQUIREMENTS OF TSCA.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 2
FLAMMABILITY 1
INSTABILITY 0
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED
FOR USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED
ON THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO
INCLUDE THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT
ARE KNOWN TO BE GENERATED IN SIGNIFICANT QUANTITIES.
DOCUMENT GROUP: 33-2640-2
VERSION NUMBER: 1.03
ISSUE DATE: 03/03/16
SUPERCEDES DATE: 10/15/14
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM