| Common Name: | ABRASIVE PRODUCTS, 413Q, 431Q, WETORDRY TRI-M-ITE SHEETS, PAPER |
| Manufacturer: | 3M |
| SDS Revision Date: | 2/10/2022 |
| SDS Format: | No Format Specified |
| Item Number(s): | 59MA59, 59MA60, 6TF97 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M(TM) ABRASIVE PRODUCTS, 413Q, 431Q, WETORDRY TRI-M-ITE(TM) SHEETS, PAPER
02/10/22
3M
SAFETY DATA SHEET
COPYRIGHT,2022, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR
THE PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 08-8963-4
ISSUE DATE: 02/10/22
VERSION NUMBER: 6.00
SUPERCEDES DATE: 08/01/17
| SECTION 1: IDENTIFICATION |  |
1.1. PRODUCT IDENTIFIER:
3M(TM) ABRASIVE PRODUCTS, 413Q, 431Q, WETORDRY TRI-M-ITE(TM) SHEETS, PAPER
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE: ABRASIVE PRODUCT
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: ABRASIVE SYSTEMS DIVISION
ADDRESS:
3M CENTER, ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
NOT CLASSIFIED AS HAZARDOUS ACCORDING TO OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
2.2. LABEL ELEMENTS:
SIGNAL WORD: NOT APPLICABLE.
SYMBOLS: NOT APPLICABLE.
PICTOGRAMS: NOT APPLICABLE.
44% OF THE MIXTURE CONSISTS OF INGREDIENTS OF UNKNOWN ACUTE ORAL TOXICITY.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
PAPER BACKING MIXTURE 30 - 80
SILICON CARBIDE MINERAL 409-21-2 1 - 45
CURED RESIN MIXTURE 1 - 35
PSA LINER MIXTURE <30
FILLER 37244-96-5 <15
PSA ATTACHMENT MIXTURE <15
QUARTZ SILICA 14808-60-7 <0.5 TRADE SECRET *
*THE SPECIFIC CHEMICAL IDENTITY AND/OR EXACT PERCENTAGE (CONCENTRATION)
OF THIS COMPOSITION HAS BEEN WITHHELD AS A TRADE SECRET.
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
WASH WITH SOAP AND WATER. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL
ATTENTION.
EYE CONTACT:
FLUSH WITH LARGE AMOUNTS OF WATER. REMOVE CONTACT LENSES IF EASY TO DO.
CONTINUE RINSING. IF SIGNS/SYMPTOMS PERSIST, GET MEDICAL ATTENTION.
IF SWALLOWED: NO NEED FOR FIRST AID IS ANTICIPATED.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
NO CRITICAL SYMPTOMS OR EFFECTS. SEE SECTION 11.1, INFORMATION ON
TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED:
NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
IN CASE OF FIRE:
USE A FIRE FIGHTING AGENT SUITABLE FOR ORDINARY COMBUSTIBLE MATERIAL
SUCH AS WATER OR FOAM TO EXTINGUISH.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
EXPOSURE TO EXTREME HEAT CAN GIVE RISE TO THERMAL DECOMPOSITION.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
HYDROGEN FLUORIDE DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
WEAR FULL PROTECTIVE CLOTHING, INCLUDING HELMET, SELF-CONTAINED, POSITIVE
PRESSURE OR PRESSURE DEMAND BREATHING APPARATUS, BUNKER COAT AND PANTS,
BANDS AROUND ARMS, WAIST AND LEGS, FACE MASK, AND PROTECTIVE COVERING FOR
EXPOSED AREAS OF THE HEAD.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
OBSERVE PRECAUTIONS FROM OTHER SECTIONS.
6.2. ENVIRONMENTAL PRECAUTIONS: NOT APPLICABLE.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP: NOT APPLICABLE.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
DO NOT BREATHE THERMAL DECOMPOSITION PRODUCTS. FOR INDUSTRIAL/OCCUPATIONAL
USE ONLY. NOT FOR CONSUMER SALE OR USE. AVOID BREATHING OF DUST CREATED BY
SANDING, GRINDING OR MACHINING. COMBUSTIBLE DUST MAY FORM BY ACTION OF
THIS PRODUCT ON ANOTHER MATERIAL (SUBSTRATE). DUST GENERATED FROM THE
SUBSTRATE DURING USE OF THIS PRODUCT MAY BE EXPLOSIVE IF IN SUFFICIENT
CONCENTRATION WITH AN IGNITION SOURCE. DUST DEPOSITS SHOULD NOT BE ALLOWED
TO ACCUMULATE ON SURFACES BECAUSE OF THE POTENTIAL FOR SECONDARY
EXPLOSIONS.
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
NO SPECIAL STORAGE REQUIREMENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN THE
TABLE BELOW, AN OCCUPATIONAL EXPOSURE LIMIT IS NOT AVAILABLE FOR THE
COMPONENT.
INGREDIENT C.A.S. AGENCY LIMIT ADDITIONAL
NO. TYPE COMMENTS
QUARTZ SILICA 14808-60-7 ACGIH TWA: A2:
(RESPIRABLE SUSPECTED
FRACTION): HUMAN CARCIN
0.025 MG/M3
QUARTZ SILICA 14808-60-7 OSHA TWA:
TABLE Z-
1(RESPIRABLE):
0.05 MG/M3;
TWA:
TABLE Z-
3(RESPIRABLE):
0.1 MG/M3;
TWA:
CONCENTRATION
(RESPIRABLE):
0.1 MG/M3(2.4
MILLIONS OF
PARTICLES/CU. FT.)
SILICON CARBIDE 409-21-2 OSHA TWA:
MINERAL (AS TOTAL DUST):
15 MG/M3
TWA:
(RESPIRABLE
FRACTION): 5 MG/M3
SILICON CARBIDE, 409-21-2 ACGIH TWA:
NONFIBROUS, (RESPIRABLE
RESPIRABLE FRACTION FRACTION): 3 MG/M3
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
AIHA: AMERICAN INDUSTRIAL HYGIENE ASSOCIATION
CMRG: CHEMICAL MANUFACTURER'S RECOMMENDED GUIDELINES
OSHA:
UNITED STATES DEPARTMENT OF LABOR - OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION
TWA: TIME-WEIGHTED-AVERAGE
STEL: SHORT TERM EXPOSURE LIMIT
CEIL: CEILING
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
FOR THOSE SITUATIONS WHERE THE MATERIAL MIGHT BE EXPOSED TO EXTREME
OVERHEATING DUE TO MISUSE OR EQUIPMENT FAILURE, USE WITH APPROPRIATE
LOCAL EXHAUST VENTILATION SUFFICIENT TO MAINTAIN LEVELS OF THERMAL
DECOMPOSITION PRODUCTS BELOW THEIR EXPOSURE GUIDELINES. PROVIDE
APPROPRIATE LOCAL EXHAUST VENTILATION FOR SANDING, GRINDING OR MACHINING.
USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO
CONTROL AIRBORNE EXPOSURES TO BELOW RELEVANT EXPOSURE LIMITS AND/OR
CONTROL DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS NOT ADEQUATE,
USE RESPIRATORY PROTECTION EQUIPMENT. PROVIDE LOCAL EXHAUST AT PROCESS
EMISSION SOURCES TO CONTROL EXPOSURE NEAR THE SOURCE AND TO PREVENT THE
ESCAPE OF DUST INTO THE WORK AREA. ENSURE THAT DUST-HANDLING SYSTEMS (SUCH
AS EXHAUST DUCTS, DUST COLLECTORS, VESSELS, AND PROCESSING EQUIPMENT) ARE
DESIGNED IN A MANNER TO PREVENT THE ESCAPE OF DUST INTO THE WORK AREA
(I.E., THERE IS NO LEAKAGE FROM THE EQUIPMENT).
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
TO MINIMIZE THE RISK OF INJURY TO FACE AND EYES, ALWAYS WEAR EYE AND FACE
PROTECTION WHEN WORKING AT SANDING OR GRINDING OPERATIONS OR WHEN NEAR
SUCH OPERATIONS. SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT
BASED ON THE RESULTS OF AN EXPOSURE ASSESSMENT. THE FOLLOWING EYE/FACE
PROTECTION(S) ARE RECOMMENDED:
SAFETY GLASSES WITH SIDE SHIELDS
SKIN/HAND PROTECTION:
WEAR APPROPRIATE GLOVES TO MINIMIZE RISK OF INJURY TO SKIN FROM CONTACT
WITH DUST OR PHYSICAL ABRASION FROM GRINDING OR SANDING.
RESPIRATORY PROTECTION:
ASSESS EXPOSURE CONCENTRATIONS OF ALL MATERIALS INVOLVED IN THE WORK
PROCESS. CONSIDER MATERIAL BEING ABRADED WHEN DETERMINING THE APPROPRIATE
RESPIRATORY PROTECTION. SELECT AND USE APPROPRIATE RESPIRATORS TO PREVENT
INHALATION OVEREXPOSURE.
AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF A RESPIRATOR IS
REQUIRED. IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS PART OF A FULL
RESPIRATORY PROTECTION PROGRAM. BASED ON THE RESULTS OF THE EXPOSURE
ASSESSMENT, SELECT FROM THE FOLLOWING RESPIRATOR TYPE(S) TO REDUCE
INHALATION EXPOSURE:
FOR THOSE SITUATIONS WHERE THE MATERIAL MIGHT BE EXPOSED TO EXTREME
OVERHEATING DUE TO MISUSE OR EQUIPMENT FAILURE, USE A POSITIVE PRESSURE
SUPPLIED-AIR RESPIRATOR.
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
PARTICULATES
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
APPEARANCE:
PHYSICAL STATE: SOLID
COLOR: GRAY
ODOR: ODORLESS
ODOR THRESHOLD: NOT APPLICABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: NOT APPLICABLE
FLASH POINT: NOT APPLICABLE
EVAPORATION RATE: NOT APPLICABLE
FLAMMABILITY (SOLID, GAS): NOT CLASSIFIED
FLAMMABLE LIMITS(LEL): NOT APPLICABLE
FLAMMABLE LIMITS(UEL): NOT APPLICABLE
VAPOR PRESSURE: NOT APPLICABLE
VAPOR DENSITY: NOT APPLICABLE
DENSITY: NO DATA AVAILABLE
SPECIFIC GRAVITY: NOT APPLICABLE
SOLUBILITY IN WATER: NOT APPLICABLE
SOLUBILITY- NON-WATER: NOT APPLICABLE
PARTITION COEFFICIENT N-OCTANOL/ WATER: NOT APPLICABLE
AUTOIGNITION TEMPERATURE: NOT APPLICABLE
DECOMPOSITION TEMPERATURE: NOT APPLICABLE
VISCOSITY: NOT APPLICABLE
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL IS CONSIDERED TO BE NON REACTIVE UNDER NORMAL USE
CONDITIONS.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID: NONE KNOWN.
10.5. INCOMPATIBLE MATERIALS: NONE KNOWN.
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
EXTREME HEAT ARISING FROM SITUATIONS SUCH AS MISUSE OR EQUIPMENT FAILURE
CAN GENERATE HYDROGEN FLUORIDE AS A DECOMPOSITION PRODUCT.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR THE
SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT BELOW
THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
DUST FROM GRINDING, SANDING OR MACHINING MAY CAUSE IRRITATION OF THE
RESPIRATORY SYSTEM. SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL
DISCHARGE, HEADACHE, HOARSENESS, AND NOSE AND THROAT PAIN.
SKIN CONTACT:
MECHANICAL SKIN IRRITATION: SIGNS/SYMPTOMS MAY INCLUDE ABRASION, REDNESS,
PAIN, AND ITCHING.
ALLERGIC SKIN REACTION (NON-PHOTO INDUCED) IN SENSITIVE PEOPLE:
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, BLISTERING, AND ITCHING.
EYE CONTACT:
MECHANICAL EYE IRRITATION: SIGNS/SYMPTOMS MAY INCLUDE PAIN, REDNESS,
TEARING AND CORNEAL ABRASION.
DUST CREATED BY GRINDING, SANDING, OR MACHINING MAY CAUSE EYE IRRITATION.
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND BLURRED
OR HAZY VISION.
INGESTION: NO HEALTH EFFECTS ARE EXPECTED.
CARCINOGENICITY:
INGREDIENT CAS NO. CLASS DESCRIPTION REGULATION
SILICA, 14808-60-7 KNOWN TO BE HUMAN NATIONAL TOXICOLOGY
CRYSTALLINE CARCINOGEN. PROGRAM CARCINOGENS
(RESPIRABLE
SIZE)
SILICA DUST, 14808-60-7 GRP. 1: INTERNATIONAL AGENCY FOR
CRYSTALLINE, IN CARCINOGENIC TO RESEARCH ON CANCER
THE FORM OF HUMANS
QUARTZ OR
CRISTOBALITE
ADDITIONAL INFORMATION:
THIS DOCUMENT COVERS ONLY THE 3M PRODUCT. FOR COMPLETE ASSESSMENT, WHEN
DETERMINING THE DEGREE OF HAZARD, THE MATERIAL BEING ABRADED MUST ALSO BE
CONSIDERED.
THIS PRODUCT CONTAINS A FORM OF CRYSTALLINE SILICA. OCCUPATIONAL EXPOSURE
TO INHALED CRYSTALLINE SILICA HAS BEEN ASSOCIATED WITH SILICOSIS AND LUNG
CANCER. NO EXPOSURE TO CRYSTALLINE SILICA IS EXPECTED DURING THE NORMAL
HANDLING AND USE OF THIS PRODUCT. THEREFORE, THE HEALTH EFFECTS ASSOCIATED
WITH CRYSTALLINE SILICA ARE NOT EXPECTED DURING NORMAL USE OF THIS
PRODUCT.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT INGESTION NO DATA AVAILABLE; CALCULATED ATE
>5,000 MG/KG
SILICON CARBIDE DERMAL RAT LD50: >2,000 MG/KG
MINERAL
SILICON CARBIDE INGESTION RAT LD50: >2,000 MG/KG
MINERAL
FILLER DERMAL LD50: ESTIMATED TO BE >5,000 MG/KG
FILLER INGESTION LD50: ESTIMATED TO BE 2,000 - 5,000
MG/KG
QUARTZ SILICA DERMAL LD50: ESTIMATED TO BE >5,000 MG/KG
QUARTZ SILICA INGESTION LD50: ESTIMATED TO BE >5,000 MG/KG
ATE: ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
SILICON CARBIDE MINERAL RAT NO SIGNIFICANT IRRITATION
FILLER PROFESSIONAL NO SIGNIFICANT IRRITATION
JUDGEMENT
QUARTZ SILICA PROFESSIONAL NO SIGNIFICANT IRRITATION
JUDGEMENT
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
SILICON CARBIDE MINERAL PROFESSIONAL NO SIGNIFICANT IRRITATION
JUDGEMENT
FILLER PROFESSIONAL MILD IRRITANT
JUDGEMENT
SKIN SENSITIZATION:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
RESPIRATORY SENSITIZATION:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
QUARTZ SILICA IN VITRO SOME POSITIVE DATA EXIST, BUT THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION
QUARTZ SILICA IN VIVO SOME POSITIVE DATA EXIST, BUT THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION
CARCINOGENICITY:
NAME ROUTE SPECIES VALUE
QUARTZ SILICA INHALATION HUMAN AND ANIMAL CARCINOGENIC
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET VALUE
ORGAN(S)
QUARTZ SILICA INHALATION SILICOSIS CAUSES DAMAGE TO ORGANS THROUGH
PROLONGED OR REPEATED EXPOSURE
NAME SPECIES TEST RESULT EXPOSURE DURATION
QUARTZ SILICA HUMAN NOAEL NOT AVAILABLE OCCUPATIONAL EXPOSURE
ASPIRATION HAZARD:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR
THE DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED ON THE FIRST PAGE OF THE
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED ON THE FIRST PAGE OF THE
SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR
ITS COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED ON THE FIRST PAGE OF THE
SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/ CONTAINER IN ACCORDANCE WITH THE LOCAL/REGIONAL/
NATIONAL/INTERNATIONAL REGULATIONS.
PRIOR TO DISPOSAL, CONSULT ALL APPLICABLE AUTHORITIES AND REGULATIONS TO
INSURE PROPER CLASSIFICATION. THE SUBSTRATE THAT WAS ABRADED MUST BE
CONSIDERED AS A FACTOR IN THE DISPOSAL METHOD FOR THIS PRODUCT. DISPOSE
OF WASTE PRODUCT IN A PERMITTED INDUSTRIAL WASTE FACILITY. AS A DISPOSAL
ALTERNATIVE, INCINERATE IN A PERMITTED WASTE INCINERATION FACILITY.
COMBUSTION PRODUCTS WILL INCLUDE HF. FACILITY MUST BE CAPABLE OF HANDLING
HALOGENATED MATERIALS. IF NO OTHER DISPOSAL OPTIONS ARE AVAILABLE, WASTE
PRODUCT MAY BE PLACED IN A LANDFILL PROPERLY DESIGNED FOR INDUSTRIAL
WASTE.
| SECTION 14: TRANSPORT INFORMATION | |
NOT REGULATED PER U.S. DOT, IATA OR IMO.
THESE TRANSPORTATION CLASSIFICATIONS ARE PROVIDED AS A CUSTOMER SERVICE.
AS THE SHIPPER YOU REMAIN RESPONSIBLE FOR COMPLYING WITH ALL APPLICABLE
LAWS AND REGULATIONS, INCLUDING PROPER TRANSPORTATION CLASSIFICATION AND
PACKAGING. 3M TRANSPORTATION CLASSIFICATIONS ARE BASED ON PRODUCT
FORMULATION, PACKAGING, 3M POLICIES AND 3M UNDERSTANDING OF APPLICABLE
CURRENT REGULATIONS. 3M DOES NOT GUARANTEE THE ACCURACY OF THIS
CLASSIFICATION INFORMATION. THIS INFORMATION APPLIES ONLY TO
TRANSPORTATION CLASSIFICATION AND NOT THE PACKAGING, LABELING, OR MARKING
REQUIREMENTS. THE ORIGINAL 3M PACKAGE IS CERTIFIED FOR U.S. GROUND
SHIPMENT ONLY. IF YOU ARE SHIPPING BY AIR OR OCEAN, THE PACKAGE MAY NOT
MEET APPLICABLE REGULATORY REQUIREMENTS.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
EPCRA 311/312 HAZARD CLASSIFICATIONS:
PHYSICAL HAZARDS: NOT APPLICABLE
HEALTH HAZARDS: NOT APPLICABLE
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
15.3. CHEMICAL INVENTORIES:
THIS PRODUCT IS AN ARTICLE AS DEFINED BY TSCA REGULATIONS, AND IS EXEMPT
FROM TSCA INVENTORY LISTING REQUIREMENTS.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 3
FLAMMABILITY 1
INSTABILITY 0
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED
FOR USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO
INCLUDE THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT
ARE KNOWN TO BE GENERATED IN SIGNIFICANT QUANTITIES.
THE NFPA HEALTH CODE OF 3 IS DUE TO EMERGENCY SITUATIONS WHERE THE
MATERIAL MAY THERMALLY DECOMPOSE AND RELEASE HYDROGEN FLUORIDE. DURING
NORMAL USE CONDITIONS, PLEASE REFERENCE SECTION 2 AND SECTION 11 OF THE
SDS FOR ADDITIONAL HEALTH HAZARD INFORMATION.
DOCUMENT GROUP: 08-8963-4
ISSUE DATE: 02/10/22
VERSION NUMBER: 6.00
SUPERCEDES DATE: 08/01/17
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M.
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM