| Common Name: | ABRASIVE PRODUCTS, TRIZACT 464LA, 468LA |
| Manufacturer: | 3M |
| SDS Revision Date: | 8/23/2016 |
| SDS Format: | GHS-US |
| Item Number(s): | 6RX77, 6TP92 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M(TM) ABRASIVE PRODUCTS, TRIZACT(TM) 464LA, 468LA
08/23/16
3M
SAFETY DATA SHEET
COPYRIGHT, 2016, 3M COMPANY.
ALL RIGHTS RESERVED. COPYING AND/OR DOWNLOADING OF THIS INFORMATION FOR THE
PURPOSE OF PROPERLY UTILIZING 3M PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
DOCUMENT GROUP: 25-2324-9
VERSION NUMBER: 2.11
ISSUE DATE: 08/23/16
SUPERCEDES DATE: 08/12/16
| SECTION 1: IDENTIFICATION |  |
1.1. PRODUCT IDENTIFIER: 3M(TM) ABRASIVE PRODUCTS, TRIZACT(TM) 464LA, 468LA
1.2. RECOMMENDED USE AND RESTRICTIONS ON USE:
RECOMMENDED USE: ABRASIVE PRODUCT
1.3. SUPPLIER'S DETAILS:
MANUFACTURER: 3M
DIVISION: ABRASIVE SYSTEMS DIVISION
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
USA
TELEPHONE: 1-888-3M HELPS (1-888-364-3577)
1.4. EMERGENCY TELEPHONE NUMBER:
1-800-364-3577 OR (651) 737-6501 (24 HOURS)
| SECTION 2: HAZARD IDENTIFICATION | |
2.1. HAZARD CLASSIFICATION:
NOT CLASSIFIED AS HAZARDOUS ACCORDING TO OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
2.2. LABEL ELEMENTS:
SIGNAL WORD: NOT APPLICABLE.
SYMBOLS: NOT APPLICABLE.
PICTOGRAMS: NOT APPLICABLE.
2.3. HAZARDS NOT OTHERWISE CLASSIFIED: NONE.
| SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
SILICON CARBIDE MINERAL 409-21-2 10 - 30
SYNTHETIC AMORPHOUS SILICA, FUMED, 112945-52-5 0.1 - 2.5
CRYSTALLINE FREE
ADDITIVE 84133-50-6 0.01 - 2
LUBRICANT 8042-47-5 0 - 0.2
CURED RESIN MIXTURE 10 - 30
FILM BACKING MIXTURE 50 - 70
| SECTION 4: FIRST AID MEASURES | |
4.1. DESCRIPTION OF FIRST AID MEASURES:
INHALATION:
REMOVE PERSON TO FRESH AIR. IF YOU FEEL UNWELL, GET MEDICAL ATTENTION.
SKIN CONTACT:
WASH WITH SOAP AND WATER. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL ATTENTION.
EYE CONTACT:
FLUSH WITH LARGE AMOUNTS OF WATER. REMOVE CONTACT LENSES IF EASY TO DO.
CONTINUE RINSING. IF SIGNS/SYMPTOMS PERSIST, GET MEDICAL ATTENTION.
IF SWALLOWED: NO NEED FOR FIRST AID IS ANTICIPATED.
4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED:
SEE SECTION 11.1. INFORMATION ON TOXICOLOGICAL EFFECTS.
4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT
REQUIRED: NOT APPLICABLE
| SECTION 5: FIRE-FIGHTING MEASURES | |
5.1. SUITABLE EXTINGUISHING MEDIA:
MATERIAL WILL NOT BURN. USE A FIRE FIGHTING AGENT SUITABLE FOR THE
SURROUNDING FIRE.
5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE:
NONE INHERENT IN THIS PRODUCT.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
5.3. SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS:
NO SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS ARE ANTICIPATED.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES:
OBSERVE PRECAUTIONS FROM OTHER SECTIONS.
6.2. ENVIRONMENTAL PRECAUTIONS: NOT APPLICABLE.
6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP: NOT APPLICABLE.
| SECTION 7: HANDLING AND STORAGE | |
7.1. PRECAUTIONS FOR SAFE HANDLING:
AVOID BREATHING OF DUST CREATED BY SANDING, GRINDING OR MACHINING.
COMBUSTIBLE DUST MAY FORM BY ACTION OF THIS PRODUCT ON ANOTHER MATERIAL
(SUBSTRATE). DUST GENERATED FROM THE SUBSTRATE DURING USE OF THIS PRODUCT
MAY BE EXPLOSIVE IF IN SUFFICIENT CONCENTRATION WITH AN IGNITION SOURCE.
DUST DEPOSITS SHOULD NOT BE ALLOWED TO ACCUMULATE ON SURFACES BECAUSE OF
THE POTENTIAL FOR SECONDARY EXPLOSIONS.
7.2. CONDITIONS FOR SAFE STORAGE INCLUDING ANY INCOMPATIBILITIES:
NO SPECIAL STORAGE REQUIREMENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1. CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN THE TABLE
BELOW, AN OCCUPATIONAL EXPOSURE LIMIT IS NOT AVAILABLE FOR THE COMPONENT.
INGREDIENT C.A.S. NO. AGENCY LIMIT TYPE ADDITIONAL
COMMENTS
SILICA, 112945-52-5 OSHA TWA CONCENTRATION:
AMORPHOUS 0.8 MG/M3
TWA:
20 MILLIONS OF
PARTICLES/CU. FT.
SILICON CARBIDE 409-21-2 OSHA TWA (AS TOTAL DUST):
MINERAL 15 MG/M3
TWA (RESPIRABLE
FRACTION): 5 MG/M3
MINERAL OILS, 8042-47-5 ACGIH TWA (INHALABLE A4:
HIGHLY-REFINED FRACTION): 5 MG/M3 NOT CLASS.
OILS AS HUMAN
CARCIN
PARAFFIN OIL 8042-47-5 OSHA TWA (AS MIST): 5 MG/M3
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
AIHA: AMERICAN INDUSTRIAL HYGIENE ASSOCIATION
CMRG: CHEMICAL MANUFACTURER'S RECOMMENDED GUIDELINES
OSHA:
UNITED STATES DEPARTMENT OF LABOR - OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION
TWA: TIME-WEIGHTED-AVERAGE
STEL: SHORT TERM EXPOSURE LIMIT
CEIL: CEILING
8.2. EXPOSURE CONTROLS:
8.2.1. ENGINEERING CONTROLS:
PROVIDE APPROPRIATE LOCAL EXHAUST VENTILATION FOR SANDING, GRINDING OR
MACHINING. USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST
VENTILATION TO CONTROL AIRBORNE EXPOSURES TO BELOW RELEVANT EXPOSURE LIMITS
AND/OR CONTROL DUST/FUME/GAS/MIST/VAPORS/SPRAY. IF VENTILATION IS NOT
ADEQUATE, USE RESPIRATORY PROTECTION EQUIPMENT. PROVIDE LOCAL EXHAUST AT
PROCESS EMISSION SOURCES TO CONTROL EXPOSURE NEAR THE SOURCE AND TO PREVENT
THE ESCAPE OF DUST INTO THE WORK AREA. ENSURE THAT DUST-HANDLING SYSTEMS
(SUCH AS EXHAUST DUCTS, DUST COLLECTORS, VESSELS, AND PROCESSING EQUIPMENT)
ARE DESIGNED IN A MANNER TO PREVENT THE ESCAPE OF DUST INTO THE WORK AREA
(I.E., THERE IS NO LEAKAGE FROM THE EQUIPMENT).
8.2.2. PERSONAL PROTECTIVE EQUIPMENT (PPE):
EYE/FACE PROTECTION:
TO MINIMIZE THE RISK OF INJURY TO FACE AND EYES, ALWAYS WEAR EYE AND FACE
PROTECTION WHEN WORKING AT SANDING OR GRINDING OPERATIONS OR WHEN NEAR SUCH
OPERATIONS. SELECT AND USE EYE/FACE PROTECTION TO PREVENT CONTACT BASED ON
THE RESULTS OF AN EXPOSURE ASSESSMENT. THE FOLLOWING EYE/FACE PROTECTION(S)
ARE RECOMMENDED: SAFETY GLASSES WITH SIDE SHIELDS
SKIN/HAND PROTECTION:
WEAR APPROPRIATE GLOVES TO MINIMIZE RISK OF INJURY TO SKIN FROM CONTACT
WITH DUST OR PHYSICAL ABRASION FROM GRINDING OR SANDING.
RESPIRATORY PROTECTION:
ASSESS EXPOSURE CONCENTRATIONS OF ALL MATERIALS INVOLVED IN THE WORK
PROCESS. CONSIDER MATERIAL BEING ABRADED WHEN DETERMINING THE APPROPRIATE
RESPIRATORY PROTECTION. SELECT AND USE APPROPRIATE RESPIRATORS TO PREVENT
INHALATION OVEREXPOSURE. AN EXPOSURE ASSESSMENT MAY BE NEEDED TO DECIDE IF
A RESPIRATOR IS REQUIRED. IF A RESPIRATOR IS NEEDED, USE RESPIRATORS AS
PART OF A FULL RESPIRATORY PROTECTION PROGRAM. BASED ON THE RESULTS OF THE
EXPOSURE ASSESSMENT, SELECT FROM THE FOLLOWING RESPIRATOR TYPE(S) TO REDUCE
INHALATION EXPOSURE:
HALF FACEPIECE OR FULL FACEPIECE AIR-PURIFYING RESPIRATOR SUITABLE FOR
PARTICULATES
FOR QUESTIONS ABOUT SUITABILITY FOR A SPECIFIC APPLICATION, CONSULT WITH
YOUR RESPIRATOR MANUFACTURER.
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES:
GENERAL PHYSICAL FORM: SOLID
ODOR, COLOR, GRADE: SOLID ABRASIVE PRODUCT
ODOR THRESHOLD: NOT APPLICABLE
PH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
BOILING POINT: NOT APPLICABLE
FLASH POINT: NOT APPLICABLE
EVAPORATION RATE: NOT APPLICABLE
FLAMMABILITY (SOLID, GAS): NOT CLASSIFIED
FLAMMABLE LIMITS (LEL): NOT APPLICABLE
FLAMMABLE LIMITS (UEL): NOT APPLICABLE
VAPOR PRESSURE: NOT APPLICABLE
VAPOR DENSITY: NOT APPLICABLE
SPECIFIC GRAVITY: NOT APPLICABLE
SOLUBILITY IN WATER: NOT APPLICABLE
SOLUBILITY-NON-WATER: NOT APPLICABLE
PARTITION COEFFICIENT N-OCTANOL/ WATER: NOT APPLICABLE
AUTOIGNITION TEMPERATURE: NOT APPLICABLE
DECOMPOSITION TEMPERATURE: NOT APPLICABLE
VISCOSITY: NOT APPLICABLE
VOLATILE ORGANIC COMPOUNDS: NO DATA AVAILABLE
| SECTION 10: STABILITY AND REACTIVITY | |
10.1. REACTIVITY:
THIS MATERIAL IS CONSIDERED TO BE NON REACTIVE UNDER NORMAL USE CONDITIONS.
10.2. CHEMICAL STABILITY: STABLE.
10.3. POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
10.4. CONDITIONS TO AVOID: NONE KNOWN.
10.5. INCOMPATIBLE MATERIALS: NONE KNOWN.
10.6. HAZARDOUS DECOMPOSITION PRODUCTS:
SUBSTANCE CONDITION
NONE KNOWN.
REFER TO SECTION 5.2 FOR HAZARDOUS DECOMPOSITION PRODUCTS DURING
COMBUSTION.
| SECTION 11: TOXICOLOGICAL INFORMATION | |
THE INFORMATION BELOW MAY NOT BE CONSISTENT WITH THE MATERIAL
CLASSIFICATION IN SECTION 2 IF SPECIFIC INGREDIENT CLASSIFICATIONS ARE
MANDATED BY A COMPETENT AUTHORITY. IN ADDITION, TOXICOLOGICAL DATA ON
INGREDIENTS MAY NOT BE REFLECTED IN THE MATERIAL CLASSIFICATION AND/OR THE
SIGNS AND SYMPTOMS OF EXPOSURE, BECAUSE AN INGREDIENT MAY BE PRESENT BELOW
THE THRESHOLD FOR LABELING, AN INGREDIENT MAY NOT BE AVAILABLE FOR
EXPOSURE, OR THE DATA MAY NOT BE RELEVANT TO THE MATERIAL AS A WHOLE.
11.1. INFORMATION ON TOXICOLOGICAL EFFECTS:
SIGNS AND SYMPTOMS OF EXPOSURE:
BASED ON TEST DATA AND/OR INFORMATION ON THE COMPONENTS, THIS MATERIAL MAY
PRODUCE THE FOLLOWING HEALTH EFFECTS:
INHALATION:
DUST FROM GRINDING, SANDING OR MACHINING MAY CAUSE IRRITATION OF THE
RESPIRATORY SYSTEM. SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL
DISCHARGE, HEADACHE, HOARSENESS, AND NOSE AND THROAT PAIN.
SKIN CONTACT:
MECHANICAL SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABRASION, REDNESS, PAIN, AND ITCHING.
ALLERGIC SKIN REACTION (NON-PHOTO INDUCED) IN SENSITIVE PEOPLE:
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, BLISTERING, AND ITCHING.
EYE CONTACT:
MECHANICAL EYE IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE PAIN, REDNESS, TEARING AND CORNEAL ABRASION.
DUST CREATED BY GRINDING, SANDING, OR MACHINING MAY CAUSE EYE IRRITATION.
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND BLURRED OR
HAZY VISION.
INGESTION: NO HEALTH EFFECTS ARE EXPECTED.
CARCINOGENICITY:
INGREDIENT CAS NO. CLASS DESCRIPTION REGULATION
SILICON CARBIDE 409-21-2 GRP. 2A: INTERNATIONAL AGENCY FOR
MINERAL PROBABLE HUMAN CARC. RESEARCH ON CANCER
ADDITIONAL INFORMATION:
THIS PRODUCT, WHEN USED UNDER REASONABLE CONDITIONS AND IN ACCORDANCE WITH
THE 3M DIRECTIONS FOR USE, SHOULD NOT PRESENT A HEALTH HAZARD. HOWEVER, USE
OR PROCESSING OF THE PRODUCT IN A MANNER NOT IN ACCORDANCE WITH THE
PRODUCT'S DIRECTIONS FOR USE MAY AFFECT THE PERFORMANCE OF THE PRODUCT AND
MAY PRESENT POTENTIAL HEALTH AND SAFETY HAZARDS.
THIS DOCUMENT COVERS ONLY THE 3M PRODUCT. FOR COMPLETE ASSESSMENT, WHEN
DETERMINING THE DEGREE OF HAZARD, THE MATERIAL BEING ABRADED MUST ALSO BE
CONSIDERED.
TOXICOLOGICAL DATA:
IF A COMPONENT IS DISCLOSED IN SECTION 3 BUT DOES NOT APPEAR IN A TABLE
BELOW, EITHER NO DATA ARE AVAILABLE FOR THAT ENDPOINT OR THE DATA ARE NOT
SUFFICIENT FOR CLASSIFICATION.
ACUTE TOXICITY:
NAME ROUTE SPECIES VALUE
OVERALL PRODUCT INGESTION NO DATA AVAILABLE;
CALCULATED ATE:
>5,000 MG/KG
SILICON CARBIDE MINERAL DERMAL RAT LD50: >2,000 MG/KG
SILICON CARBIDE MINERAL INGESTION RAT LD50: >2,000 MG/KG
SYNTHETIC AMORPHOUS SILICA, DERMAL RABBIT LD50: >5,000 MG/KG
FUMED, CRYSTALLINE FREE
SYNTHETIC AMORPHOUS SILICA, INHALATION- RAT LC50: >0.691 MG/L
FUMED, CRYSTALLINE FREE DUST/MIST
(4 HOURS)
SYNTHETIC AMORPHOUS SILICA, INGESTION RAT LD50: >5,110 MG/KG
FUMED, CRYSTALLINE FREE
ADDITIVE DERMAL RABBIT LD50: 1,127 MG/KG
ADDITIVE INHALATION- RAT LC50: 1.1 MG/L
DUST/MIST
(4 HOURS)
ADDITIVE INGESTION RAT LD50: 412 MG/KG
LUBRICANT DERMAL RABBIT LD50: >2,000 MG/KG
LUBRICANT INGESTION RAT LD50: >5,000 MG/KG
ATE = ACUTE TOXICITY ESTIMATE
SKIN CORROSION/IRRITATION:
NAME SPECIES VALUE
SILICON CARBIDE MINERAL RAT NO SIGNIFICANT IRRITATION
SYNTHETIC AMORPHOUS SILICA, RABBIT NO SIGNIFICANT IRRITATION
FUMED, CRYSTALLINE FREE
LUBRICANT RABBIT NO SIGNIFICANT IRRITATION
SERIOUS EYE DAMAGE/IRRITATION:
NAME SPECIES VALUE
SILICON CARBIDE MINERAL PROFESSIONAL NO SIGNIFICANT IRRITATION
JUDGEMENT
SYNTHETIC AMORPHOUS SILICA, RABBIT NO SIGNIFICANT IRRITATION
FUMED, CRYSTALLINE FREE
LUBRICANT RABBIT MILD IRRITANT
SKIN SENSITIZATION:
NAME SPECIES VALUE
SYNTHETIC AMORPHOUS SILICA, HUMAN NOT SENSITIZING
FUMED, CRYSTALLINE FREE AND
ANIMAL
LUBRICANT GUINEA NOT SENSITIZING
PIG
RESPIRATORY SENSITIZATION:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
GERM CELL MUTAGENICITY:
NAME ROUTE VALUE
SYNTHETIC AMORPHOUS SILICA, IN VITRO NOT MUTAGENIC
FUMED, CRYSTALLINE FREE
LUBRICANT IN VITRO NOT MUTAGENIC
CARCINOGENICITY:
NAME ROUTE SPECIES VALUE
SYNTHETIC AMORPHOUS NOT MOUSE SOME POSITIVE DATA EXIST,
SILICA, FUMED, SPECIFIED BUT THE DATA ARE NOT
CRYSTALLINE FREE SUFFICIENT FOR
CLASSIFICATION
LUBRICANT DERMAL MOUSE NOT CARCINOGENIC
LUBRICANT INHALATION MULTIPLE NOT CARCINOGENIC
ANIMAL
SPECIES
REPRODUCTIVE TOXICITY:
REPRODUCTIVE AND/OR DEVELOPMENTAL EFFECTS:
NAME ROUTE VALUE
SYNTHETIC AMORPHOUS SILICA, INGESTION NOT TOXIC TO FEMALE
FUMED, CRYSTALLINE FREE REPRODUCTION
SYNTHETIC AMORPHOUS SILICA, INGESTION NOT TOXIC TO MALE REPRODUCTION
FUMED, CRYSTALLINE FREE
SYNTHETIC AMORPHOUS SILICA, INGESTION NOT TOXIC TO DEVELOPMENT
FUMED, CRYSTALLINE FREE
LUBRICANT INGESTION NOT TOXIC TO FEMALE
REPRODUCTION
LUBRICANT INGESTION NOT TOXIC TO MALE REPRODUCTION
LUBRICANT INGESTION NOT TOXIC TO DEVELOPMENT
NAME SPECIES TEST RESULT EXPOSURE DURATION
SYNTHETIC AMORPHOUS RAT NOAEL: 509 MG/KG/DAY 1 GENERATION
SILICA, FUMED,
CRYSTALLINE FREE
SYNTHETIC AMORPHOUS RAT NOAEL: 497 MG/KG/DAY 1 GENERATION
SILICA, FUMED,
CRYSTALLINE FREE
SYNTHETIC AMORPHOUS RAT NOAEL: 1,350 MG/KG/DAY DURING
SILICA, FUMED, ORGANOGENESIS
CRYSTALLINE FREE
LUBRICANT RAT NOAEL: 4,350 MG/KG/DAY 13 WEEKS
LUBRICANT RAT NOAEL: 4,350 MG/KG/DAY 13 WEEKS
LUBRICANT RAT NOAEL: 4,350 MG/KG/DAY DURING
GESTATION
TARGET ORGAN(S):
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE:
FOR THE COMPONENT/COMPONENTS, EITHER NO DATA ARE CURRENTLY AVAILABLE OR THE
DATA ARE NOT SUFFICIENT FOR CLASSIFICATION.
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE:
NAME ROUTE TARGET ORGAN(S) VALUE
SYNTHETIC AMORPHOUS INHALATION RESPIRATORY SYSTEM ALL DATA ARE
SILICA, FUMED, SILICOSIS NEGATIVE
CRYSTALLINE FREE
LUBRICANT INGESTION HEMATOPOIETIC SYSTEM SOME POSITIVE
DATA EXIST, BUT
THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
LUBRICANT INGESTION LIVER SOME POSITIVE
IMMUNE SYSTEM DATA EXIST, BUT
THE DATA ARE NOT
SUFFICIENT FOR
CLASSIFICATION
NAME SPECIES TEST RESULT EXPOSURE DURATION
SYNTHETIC AMORPHOUS HUMAN NOAEL: NOT AVAILABLE OCCUPATIONAL
SILICA, FUMED, EXPOSURE
CRYSTALLINE FREE
LUBRICANT RAT NOAEL: 1,381 MG/KG/DAY 90 DAYS
LUBRICANT RAT NOAEL: 1,336 MG/KG/DAY 90 DAYS
ASPIRATION HAZARD:
NAME VALUE
LUBRICANT ASPIRATION HAZARD
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL ECOTOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
CHEMICAL FATE INFORMATION:
PLEASE CONTACT THE ADDRESS OR PHONE NUMBER LISTED IN SECTION 1 OF THIS
SDS FOR ADDITIONAL CHEMICAL FATE INFORMATION ON THIS MATERIAL AND/OR ITS
COMPONENTS.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
13.1. DISPOSAL METHODS:
DISPOSE OF CONTENTS/ CONTAINER IN ACCORDANCE WITH THE
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
PRIOR TO DISPOSAL, CONSULT ALL APPLICABLE AUTHORITIES AND REGULATIONS TO
INSURE PROPER CLASSIFICATION. THE SUBSTRATE THAT WAS ABRADED MUST BE
CONSIDERED AS A FACTOR IN THE DISPOSAL METHOD FOR THIS PRODUCT. DISPOSE OF
WASTE PRODUCT IN A PERMITTED INDUSTRIAL WASTE FACILITY. IF NO OTHER
DISPOSAL OPTIONS ARE AVAILABLE, WASTE PRODUCT MAY BE PLACED IN A LANDFILL
PROPERLY DESIGNED FOR INDUSTRIAL WASTE.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
| SECTION 14: TRANSPORT INFORMATION | |
NOT REGULATED PER U.S. DOT, IATA OR IMO.
THESE TRANSPORTATION CLASSIFICATIONS ARE PROVIDED AS A CUSTOMER SERVICE. AS
THE SHIPPER YOU REMAIN RESPONSIBLE FOR COMPLYING WITH ALL APPLICABLE LAWS
AND REGULATIONS, INCLUDING PROPER TRANSPORTATION CLASSIFICATION AND
PACKAGING. 3M TRANSPORTATION CLASSIFICATIONS ARE BASED ON PRODUCT
FORMULATION, PACKAGING, 3M POLICIES AND 3M UNDERSTANDING OF APPLICABLE
CURRENT REGULATIONS. 3M DOES NOT GUARANTEE THE ACCURACY OF THIS
CLASSIFICATION INFORMATION. THIS INFORMATION APPLIES ONLY TO TRANSPORTATION
CLASSIFICATION AND NOT THE PACKAGING, LABELING, OR MARKING REQUIREMENTS.
THE ORIGINAL 3M PACKAGE IS CERTIFIED FOR U.S. GROUND SHIPMENT ONLY. IF YOU
ARE SHIPPING BY AIR OR OCEAN, THE PACKAGE MAY NOT MEET APPLICABLE
REGULATORY REQUIREMENTS.
| SECTION 15: REGULATORY INFORMATION | |
15.1. US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
311/312 HAZARD CATEGORIES:
FIRE HAZARD: NO
PRESSURE HAZARD: NO
REACTIVITY HAZARD: NO
IMMEDIATE HAZARD: NO
DELAYED HAZARD: NO
15.2. STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
15.3. CHEMICAL INVENTORIES:
THIS PRODUCT IS AN ARTICLE AS DEFINED BY TSCA REGULATIONS, AND IS EXEMPT
FROM TSCA INVENTORY LISTING REQUIREMENTS.
CONTACT 3M FOR MORE INFORMATION.
15.4. INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS SDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 0
FLAMMABILITY 0
INSTABILITY 0
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED FOR
USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO INCLUDE
THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT ARE KNOWN
TO BE GENERATED IN SIGNIFICANT QUANTITIES.
DOCUMENT GROUP: 25-2324-9
VERSION NUMBER: 2.11
ISSUE DATE: 08/23/16
SUPERCEDES DATE: 08/12/16
DISCLAIMER:
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) IS BELIEVED TO BE CORRECT
AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER THE 3M PRODUCT IS FIT
FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S METHOD OF USE OR
APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT THE USE AND
APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN THE USER'S
KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE THE 3M
PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED IN
ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE SDS AVAILABLE DIRECTLY FROM 3M
3M USA SDSS ARE AVAILABLE AT WWW.3M.COM