| Common Name: | ABRASIVE WHEELS |
| Manufacturer: | J LONG HARDWARE ABRASIVE CHINA |
| SDS Revision Date: | 8/21/2015 |
| SDS Format: | GHS-US |
| Item Number(s): | 10L240, 10L270, 10N236, 1GBJ5, 1GBK6, 1GBL2, 1GBL8, 1GBN4, 1GBN5, 1GBT1, 33L540, 6ZFA9 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
SAFETY DATA SHEET
ACCORDING TO HAZARD COMMUNICATION STANDARD (29 CFR 1910.1200)
ABRASIVE WHEELS
ISSUE DATE: 08/21/2015
VERSION: 1.0
REVISION DATE: 08/21/2015
| 1. PRODUCT AND COMPANY IDENTIFICATION |  |
MATERIAL NAME: ABRASIVE WHEELS
CAS #: SEE SECTION 3
PRODUCT CODE:
PRODUCT USE: CUTTING AND POLISHING METAL AND STONE.
MANUFACTURER/SUPPLIER:
SUPPLIER(MANUFACTURER): J LONG HARDWARE ABRASIVE CO., LTD
ADDRESS:
EAST OF BINHE ROAD
XINCHENG AREA
DACHENG, HEBEI
CHINA
CONTACT PERSON(E-MAIL): SALES-3@ROBTEC.CN
TELEPHONE: +86-316-5568710
FAX: +86-316-5568062
EMERGENCY TELEPHONE NUMBER: +86-18631680276
| 2. HAZARDS IDENTIFICATION | |
GHS CLASSIFICATION:
PHYSICAL HAZARDS: NOT CLASSIFIED
HEALTH HAZARDS: NOT CLASSIFIED
ENVIRONMENTAL HAZARDS: NOT CLASSIFIED
GHS LABEL ELEMENTS:
HAZARD PICTOGRAMS: NO HAZARD PICTOGRAM IS USED.
SIGNAL WORD: NO SIGNAL WORD IS USED.
HAZARD STATEMENT: NOT APPLICABLE.
PRECAUTIONARY STATEMENT:
PREVENTION: NOT APPLICABLE.
RESPONSE: NOT APPLICABLE.
STORAGE: NOT APPLICABLE.
DISPOSAL: NOT APPLICABLE.
| 3. COMPOSITION / INFORMATION ON INGREDIENTS | |
COMPONENTS CAS# PERCENT
ALUMINUM OXIDE 1344-28-1 0-95
SILICON CARBIDE 409-21-2 0-95
PHENOLIC RESIN 5-20
GLASS MESH 0-10
IRON DISULPHIDE 12068-85-8 0-20
FLUORIDES (AS F) 0-15
IRON OXIDE 0-5
LIMESTONE 0-5
5-55 PERCENT OF THE MIXTURE CONSISTS OF COMPONENT (S) OF UNKNOWN TOXICITY.
| 4. FIRST AID MEASURES | |
FIRST AID PROCEDURES:
EYE CONTACT:
DO NOT EXPOSE TO DIRECT DUST SOURCE. RINSE WITH CLEAN WATER.
IF NOT SUFFICIENT, GET MEDICAL ATTENTION IMMEDIATELY.
SKIN CONTACT:
REMOVE CONTAMINATED CLOTHING. WASH SKIN THOROUGHLY WITH MILD SOAP AND
PLENTY OF WATER. GET MEDICAL ATTENTION IF IRRITATION OCCURS.
INHALATION:
IN CASE OF INHALATION, REMOVE PERSON TO FRESH AIR KEEP HIM QUIET AND WARM.
APPLY ARTIFICIAL RESPIRATION IF NECESSARY AND GET MEDICAL ATTENTION
IMMEDIATELY.
INGESTION:
IF SWALLOWED, WASH MOUTH THOROUGHLY WITH PLENTY OF WATER. GET MEDICAL
ATTENTION IMMEDIATELY.
NOTE: NEVER GIVE AN UNCONSCIOUS PERSON ANYTHING TO DRINK.
NOTES TO PHYSICIAN: TREAT SYMPTOMS.
| 5. FIRE FIGHTING MEASURE | |
FLAMMABLE PROPERTIES: NOT AVAILABLE
EXTINGUISHING MEDIA:
SUITABLE EXTINGUISHING MEDIA:
USE WATER SPRAY OR JET, DRY CHEMICAL, CARBON DIOXIDE, FOAM.
UNSUITABLE EXTINGUISHING MEDIA: NOT AVAILABLE
FIREFIGHTING EQUIPMENT/INSTRUCTIONS:
FIRE FIGHTERS SHOULD WEAR FULL PROTECTIVE CLOTHING AND SELF-CONTAINED
BREATHING APPARATUS (SCBA). CONTAIN FIRE FIGHTING WATER TO PREVENT ENTRY
INTO WATER OR DRAINAGE SYSTEMS.
HAZARDOUS COMBUSTION PRODUCTS: NOT AVAILABLE
| 6. ACCIDENTAL RELEASE MEASURES | |
PERSONAL PRECAUTIONS:
USE PERSONAL PROTECTIVE EQUIPMENT. AVOID BREATHING DUST. ENSURE ADEQUATE
VENTILATION.
REMOVE ALL SOURCES OF IGNITION. EVACUATE PERSONNEL TO SAFE AREAS. FOR
PERSONAL PROTECTION SEE SECTION 8.
ENVIRONMENTAL PRECAUTIONS:
SHOULD NOT BE RELEASED INTO THE ENVIRONMENT. IF THE PRODUCT CONTAMINATES
RIVERS AND LAKES OR DRAINS INFORM RESPECTIVE AUTHORITIES.
METHODS FOR CLEANING UP:
VACUUM OR SWEEP UP MATERIAL AND PLACE INTO A SUITABLE DISPOSAL CONTAINER.
DO NOT LET THIS CHEMICAL ENTER THE ENVIRONMENT.
| 7. HANDLING AND STORAGE | |
HANDLING:
DO VISUALLY INSPECT ALL WHEELS BEFORE MOUNTING FOR POSSIBLE DAMAGE.
DO MAKE SURE OPERATING SPEED OF MACHINE. DOES NOT EXCEED SPEED MARKED ON
WHEEL, IT'S BLOTTER OR CONTAINER. DO CHECK MOUNTING FLANGES FOR EQUAL SIZE,
RELIEVE AS REQUIRED AND CORRECT DIAMETER. DO ALLOW NEWLY MOUNTED WHEELS TO
RUN AT OPERATING SPEED, WITH GUARD IN PLACE, FOR AT LEAST ONE MINUTE BEFORE
GRINDING. DO TURN OFF COOLANT BEFORE STOPPING WHEEL TO AVOID CREATING AN
OUT-OF-BALANCE CONDITION. DO ALWAYS WEAR SAFETY GLASSES OR SOME TYPE OF
APPROVED EYE PROTECTION WHILE GRINDING OR CUTTING. DO FOLLOW COMMON SENSE
SAFETY CONSIDERATIONS. DON'T USE A WHEEL THAT HAS BEEN DROPPED OR APPEARS
TO HAVE BEEN ABUSED. DON'T FORCE A WHEEL ONTO THE MACHINE OR AFTER THE
SIZE OF THE MOUNTING HOLE. IF WHEEL WON'T FIT THE MACHINE, GET ONE THAT
WILL. DON'T START THE MACHINE UNTIL THE SAFETY GUARD IS PROPERLY AND
SECURELY IN PLACE. DON'T STAND DIRECTLY IN FRONT OF A GRINDING/CUTTING
WHEEL WHENEVER A MACHINE IS IN OPERATION. DON'T EVER EXCEED MAXIMUM
OPERATING SPEED ESTABLISHED FOR THE WHEEL. DON'T USE MOUNTING FLANGES
ON WHICH THE BEARING SURFACES ARE NOT CLEAN, FLAT, AND SMOOTH. DON'T
TIGHTEN THE MOUNTING NUT EXCESSIVELY. DON'T GRIND ON THE SIDE OF
CONVENTIONAL, STRAIGHT OR TYPE 1 WHEELS. DON'T USE A WHEEL ON ANY MACHINE
THAT IS NOT PROPERLY DESIGNED FOR THE SPECIFIC APPLICATION OF THE WHEEL.
DON'T JAM WORK INTO THE WHEEL. DON'T GRIND OR CUT MATERIAL FOR WHICH THE
WHEEL IS NOT DESIGNED.
STORAGE:
DO ALWAYS HANDLE AND STORE WHEELS IN A CAREFUL MANNER. DO BE SURE WORK
REST IS PROPERLY ADJUSTED ON BENCH, PEDESTAL, AND FLOOR STAND GRINDER.
DO ALWAYS USE SAFETY GUARD THAT COVERS A MINIMUM OF ONE-HALF THE ABRASIVE
WHEEL. STORE IN SANE AND HUMIDITY BALANCED ROOMS NOT EXCEEDING
TEMPERATURES BELOW ZERO AND HUMIDITY OVER 55-65%. EXCESSIVE HEAT AND
HUMIDITY, AS WELL AS SUDDEN CHANGES OF EXTREME TEMPERATURES MAY PUT ON
RISK THE INTEGRITY OF THE CHEMICAL STRUCTURE OF GRINDING WHEELS, THUS
CAUSING A REDUCTION OF SAFETY DURING THEIR USE, AFTER BEING MOUNTED ON
POWER TOOLS.
| 8. EXPOSURE CONTROLS / PERSONAL PROTECTION | |
CONTROL PARAMETERS:
OCCUPATIONAL EXPOSURE LIMITS (OEL):
INGREDIENT DATA:
SOURCE INGREDIENT TWA STEL
US OSHA PERMISSIBLE ALUMINUM OXIDE 15 MG/M3 / NOT AVAILABLE
EXPOSURE LEVELS 5 MG/M3
(PELS) - TABLE Z1
US OSHA PERMISSIBLE ALUMINUM OXIDE 5 MG/M3 / NOT AVAILABLE
EXPOSURE LEVELS 15 MG/M3 /
(PELS) - TABLE Z3 15 MPPCF /
50 MPPCF
US ACGIH THRESHOLD ALUMINUM OXIDE 1 MG/M3 NOT AVAILABLE
LIMIT VALUES (TLV)
US NIOSH RECOMMENDED ALUMINUM OXIDE NOT AVAILABLE NOT AVAILABLE
EXPOSURE LIMITS
(RELS)
US OSHA PERMISSIBLE SILICON CARBIDE 15 MG/M3 / NOT AVAILABLE
EXPOSURE LEVELS 5 MG/M3
(PELS) - TABLE Z1
US ACGIH THRESHOLD SILICON CARBIDE 0.1 F/CC / NOT AVAILABLE
LIMIT VALUES (TLV) 10 MG/M3 /
3 MG/M3
US NIOSH RECOMMENDED SILICON CARBIDE 10 (TOTAL), NOT AVAILABLE
EXPOSURE LIMITS (RESP) 5 MG/M3
(RELS)
SOURCE INGREDIENT PEAK NOTE
US OSHA PERMISSIBLE ALUMINUM NOT TOTAL DUST
EXPOSURE LEVELS OXIDE AVAILABLE
(PELS) - TABLE Z1
US OSHA PERMISSIBLE ALUMINUM NOT RESPIRABLE FRACTION;
EXPOSURE LEVELS OXIDE AVAILABLE ALL INERT OR NUISANCE
(PELS) - TABLE Z3 DUSTS, WHETHER MINERAL,
INORGANIC, OR ORGANIC,
NOT LISTED SPECIFICALLY
BY SUBSTANCE NAME ARE
COVERED BY THIS LIMIT,
WHICH IS THE SAME AS THE
PARTICULATES NOT OTHERWISE
REGULATED (PNOR) LIMIT IN
TABLE Z-1. / TOTAL DUST;
ALL INERT OR NUISANCE
DUSTS, WHETHER MINERAL,
INORGANIC, OR ORGANIC,
NOT LISTED SPECIFICALLY
BY SUBSTANCE NAME ARE
COVERED BY THIS LIMIT,
WHICH IS THE SAME AS THE
PARTICULATES NOT OTHERWISE
REGULATED (PNOR) LIMIT IN
TABLE Z-1.
US ACGIH THRESHOLD ALUMINUM NOT TLV(R*) BASIS:
LIMIT VALUES (TLV) OXIDE AVAILABLE PNEUMOCONIOSIS; LRT IRR;
NEUROTOXICITY
US NIOSH RECOMMENDED ALUMINUM NOT SEE APPENDIX D
EXPOSURE LIMITS OXIDE AVAILABLE
(RELS)
US OSHA PERMISSIBLE SILICON NOT TOTAL DUST
EXPOSURE LEVELS CARBIDE AVAILABLE
(PELS) - TABLE Z1
US ACGIH THRESHOLD SILICON NOT TLV(R*) BASIS:
LIMIT VALUES (TLV) CARBIDE AVAILABLE URT IRR / TLV(R*)
BASIS: MESOTHELIOMA; CANCER
US NIOSH RECOMMENDED SILICON NOT NOT AVAILABLE
EXPOSURE LIMITS CARBIDE AVAILABLE
(RELS)
EMERGENCY LIMITS:
INGREDIENT TEEL-1 TEEL-2 TEEL-3
ALUMINUM OXIDE 11 MG/M3 15 MG/M3 25 MG/M3
SILICON CARBIDE 15 MG/M3 15 MG/M3 15 MG/M3
IRON DISULPHIDE 6.4 MG/M3 69 MG/M3 420 MG/M3
INGREDIENT ORIGINAL IDLH REVISED IDLH
ALUMINUM OXIDE NOT AVAILABLE NOT AVAILABLE
SILICON CARBIDE NOT AVAILABLE NOT AVAILABLE
IRON DISULPHIDE NOT AVAILABLE NOT AVAILABLE
EXPOSURE CONTROLS:
APPROPRIATE ENGINEERING CONTROLS:
WHEN ABRASIVE PRODUCTS ARE USED, PLEASE REFER TO SAFETY MANUALS OF POWER
TOOLS AND PROFESSIONAL FIRST AID RULES AT WORK. REFER TO SAFETY
INSTRUCTIONS AND FEPA NORMS APPLICABLE TO THE CASE. WE RECOMMEND TO BE
CAREFUL DURING CUTTING AND GRINDING OF ALUMINUM AND ITS CHEMICAL
REACTIONS.
INDIVIDUAL PROTECTION MEASURES, SUCH AS PERSONAL PROTECTIVE EQUIPMENT:
EYE / FACE PROTECTION: SAFETY GUARD ON ANGLE GRINDER, FACE MASK OR GOGGLES.
SKIN PROTECTION:
SAFETY GLOVES. USE PROTECTIVE CLOTHING IMPERVIOUS TO THIS MATERIAL.
RESPIRATORY PROTECTION:
IN CASE OF INSUFFICIENT VENTILATION WEAR SUITABLE RESPIRATORY EQUIPMENT.
GENERAL HYGIENE CONSIDERATIONS:
WASH HANDS, FOREARMS AND FACE THOROUGHLY AFTER HANDLING CHEMICAL PRODUCTS,
BEFORE EATING, SMOKING AND USING THE LAVATORY AND AT THE END OF THE
WORKING PERIOD.
| 9. PHYSICAL & CHEMICAL PROPERTIES | |
APPEARANCE:
PHYSICAL: STATE SOLID
FORM: SOLID
COLOR: BROWN OR BLACK, DEPENDING ON RAW MATERIAL TYPE
ODOR: NOT AVAILABLE
ODOR THRESHOLD: NOT AVAILABLE
PH: NOT AVAILABLE
VAPOR PRESSURE: NOT AVAILABLE
VAPOR DENSITY: NOT AVAILABLE
BOILING POINT: NOT AVAILABLE
MELTING POINT/FREEZING POINT: NOT AVAILABLE
SOLUBILITY (WATER): NOT AVAILABLE
SPECIFIC GRAVITY: NOT AVAILABLE
RELATIVE DENSITY: NOT AVAILABLE
DENSITY: NOT AVAILABLE
FLASH POINT: NOT AVAILABLE
FLAMMABILITY LIMITS IN AIR, UPPER, % BY VOLUME: NOT AVAILABLE
FLAMMABILITY LIMITS IN AIR, LOWER, % BY VOLUME: NOT AVAILABLE
AUTO-IGNITION TEMPERATURE: NOT AVAILABLE
VOC: NOT AVAILABLE
PERCENT VOLATILE: NOT AVAILABLE
MOLECULAR FORMULA: NOT APPLICABLE
MOLECULAR WEIGHT: NOT APPLICABLE
OTHER DATA:
VISCOSITY: NOT AVAILABLE
| 10. CHEMICAL STABILITY & REACTIVITY INFORMATION | |
REACTIVITY:
THE SUBSTANCE IS STABLE UNDER NORMAL STORAGE AND HANDLING CONDITIONS.
CHEMICAL STABILITY: MATERIAL IS STABLE UNDER NORMAL CONDITIONS.
CONDITIONS TO AVOID: INCOMPATIBLE MATERIALS. EXCESS OF HEAT AND HUMIDITY.
INCOMPATIBLE MATERIALS: NOT AVAILABLE
HAZARDOUS DECOMPOSITION PRODUCTS: NOT AVAILABLE
POSSIBILITY OF HAZARDOUS REACTIONS:
NO DANGEROUS REACTION KNOWN UNDER CONDITIONS OF NORMAL USE.
| 11. TOXICOLOGICAL INFORMATION | |
TOXICOKINETICS, METABOLISM AND DISTRIBUTION:
NON-HUMAN TOXICOLOGICAL DATA: NOT AVAILABLE
INFORMATION ON TOXICOLOGICAL EFFECTS:
ACUTE TOXICITY:
LD50 (ORAL, RAT): NOT AVAILABLE
LD50 (DERMAL, RABBIT): NOT AVAILABLE
LC50 (INHALATION, RAT): NOT AVAILABLE
SKIN CORROSION/IRRITATION: NOT CLASSIFIED
SERIOUS EYE DAMAGE/IRRITATION: NOT CLASSIFIED
RESPIRATORY OR SKIN SENSITIZATION: NOT CLASSIFIED
GERM CELL MUTAGENICITY: NOT CLASSIFIED
CARCINOGENICITY: NOT CLASSIFIED
REPRODUCTIVE TOXICITY: NOT CLASSIFIED
STOT-SINGLE EXPOSURE: NOT CLASSIFIED
STOT-REPEATED EXPOSURE: NOT CLASSIFIED
ASPIRATION HAZARD: NOT CLASSIFIED
| 12. ECOLOGICAL INFORMATION | |
TOXICITY:
ACUTE TOXICITY TIME SPECIES METHOD EVALUATION REMARKS
LC50: N/A 96H FISH OECD 203 N/A N/A
EC50: N/A 48H DAPHNIA OECD 202 N/A N/A
EC50: N/A 72H ALGAE OECD 201 N/A N/A
PERSISTENCE AND DEGRADABILITY: NOT AVAILABLE.
BIOACCUMULATIVE POTENTIAL: NOT AVAILABLE.
MOBILITY IN SOIL: NOT AVAILABLE.
RESULTS OF PBT&VPVB ASSESSMENT: NOT AVAILABLE.
OTHER ADVERSE EFFECTS: NO KNOWN SIGNIFICANT EFFECTS OR CRITICAL HAZARDS.
| 13. DISPOSAL CONSIDERATIONS | |
DISPOSAL INSTRUCTIONS:
DISPOSE OF CONTENTS/CONTAINER IN ACCORDANCE WITH
LOCAL/REGIONAL/NATIONAL/INTERNATIONAL REGULATIONS.
CONTAMINATED PACKAGING:
SINCE EMPTIED CONTAINERS MAY RETAIN PRODUCT RESIDUE, FOLLOW LABEL WARNINGS
EVEN AFTER CONTAINER IS EMPTIED.
| 14. TRANSPORT INFORMATION | |
DOT:
BASIC SHIPPING REQUIREMENTS:
UN NUMBER: NOT REGULATED
PROPER SHIPPING NAME: NOT REGULATED
HAZARD CLASS: NOT REGULATED
PACKING GROUP: NOT REGULATED
ENVIRONMENTAL HAZARDS: NO
IATA:
UN NUMBER: NOT REGULATED
UN PROPER SHIPPING NAME: NOT REGULATED
TRANSPORT HAZARD CLASS(ES): NOT REGULATED
PACKING GROUP: NOT REGULATED
ENVIRONMENTAL HAZARDS: NO
IMDG:
UN NUMBER: NOT REGULATED
UN PROPER SHIPPING NAME: NOT REGULATED
TRANSPORT HAZARD CLASS(ES): NOT REGULATED
PACKING GROUP: NOT REGULATED
ENVIRONMENTAL HAZARDS: NO
| 15. REGULATORY INFORMATION | |
SAFETY, HEALTH AND ENVIRONMENTAL REGULATIONS / LEGISLATION SPECIFIC FOR
THE SUBSTANCE OR MIXTURE:
ALUMINUM OXIDE (1344-28-1) IS FOUND ON THE FOLLOWING REGULATORY LISTS:
US - ALASKA LIMITS FOR AIR CONTAMINANTS
US - HAWAII AIR CONTAMINANT LIMITS
US - IDAHO - LIMITS FOR AIR CONTAMINANTS
US - WYOMING TOXIC AND HAZARDOUS SUBSTANCES TABLE Z1 LIMITS FOR AIR
CONTAMINANTS
US EPCRA SECTION 313 CHEMICAL LIST
US TOXIC SUBSTANCES CONTROL ACT (TSCA) - CHEMICAL SUBSTANCE INVENTORY
SILICON CARBIDE (409-21-2) IS FOUND ON THE FOLLOWING REGULATORY LISTS:
US - ALASKA LIMITS FOR AIR CONTAMINANTS
US - HAWAII AIR CONTAMINANT LIMITS
US - IDAHO - LIMITS FOR AIR CONTAMINANTS
US - WYOMING TOXIC AND HAZARDOUS SUBSTANCES TABLE Z1 LIMITS FOR AIR
CONTAMINANTS
US TOXIC SUBSTANCES CONTROL ACT (TSCA) - CHEMICAL SUBSTANCE INVENTORY
IRON DISULPHIDE(12068-85-8) IS FOUND ON THE FOLLOWING REGULATORY LISTS:
US TOXIC SUBSTANCES CONTROL ACT (TSCA) - CHEMICAL SUBSTANCE INVENTORY
| 16. OTHER INFORMATION | |
HMIS(R*)RATINGS:
HEALTH 0
FLAMMABILITY 1
PHYSICAL HAZARD 0
NFPA RATINGS:
HEALTH 0
FLAMMABILITY 1
INSTABILITY 0
DISCLAIMER:
THE INFORMATION IN THE SHEET WAS WRITTEN BASED ON THE BEST KNOWLEDGE AND
EXPERIENCE CURRENTLY AVAILABLE.
ISSUE DATE: 08-21-2015
VERSION #: 1.0
SDS US