| Common Name: | ISOBUTANE FILL MATERIAL |
| Manufacturer: | HONEYWELL |
| SDS Revision Date: | 10/8/1999 |
| SDS Format: | No Format Specified |
| Item Number(s): | 2E517, 3TZ99, 3XK96, 4CZ52, 4NE56 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
MATERIAL SAFETY DATA SHEET
| SECTION 1. PRODUCT AND COMPANY IDENTIFICATION |  |
PRODUCT NAME: ISOBUTANE FILL MATERIAL
MSDS ID: DS9035
THIS MSDS APPLIES TO THE FILL MATERIAL WHICH IS CONTAINED WITHIN THE
TEMPERATURE SENSING ELEMENT. FILL MATERIAL WILL BE EXPOSED ONLY UPON
ELEMENT BREAKAGE. FILL VOLUME IS SMALL, TYPICALLY 0.3 - 94 CC. AND IS A GAS
AT ROOM TEMPERATURE. UNDER NORMAL HANDLING AND USAGE, THERE IS NO EXPOSURE.
THIS CHEMICAL IS CONTAINED IN A DEVICE THAT MEETS OSHA'S DEFINITION AS AN
"ARTICLE." THERE IS NO EXPOSURE TO THIS CHEMICAL UNDER NORMAL AND INTENDED
PRODUCT USAGE. THIS MSDS HAS BEEN PROVIDED IN THE EVENT THAT A DEVICE IS
BROKEN AND THE CHEMICAL IS INADVERTENTLY RELEASED.
SYNONYMS: 2-METHYLPROPANE; TRIMETHYLMETHANE
PRODUCT USE:
FILL MATERIAL FOR HONEYWELL CONTROLLERS:
T644A1249; L480; T915A1177; T915C1407, 1449; T915B1002; T915D1083, 1091;
T915F1008, 1016; T915M1018 AND T915P1007.
MANUFACTURER:
HONEYWELL INC.
1985 DOUGLAS DRIVE NORTH
MINNEAPOLIS, MN 55422
CUSTOMER RESPONSE CENTER: 800-328-5111
EMERGENCY TELEPHONE INFORMATION: 888-809-3787
DATE RELEASED: OCTOBER 8, 1999
CORP ID: GV-028-035
| SECTION 2. COMPOSITION, INFORMATION ON INGREDIENTS | |
INGREDIENTS CAS# PERCENT PEL TLV
ISOBUTANE 67-63-0 100 400 PPM 400 PPM
| SECTION 3. HAZARD IDENTIFICATION | |
ACUTE HEALTH EFFECTS:
SKIN/EYES: LIQUID SPILLED ON SKIN MAY CAUSE RAPID COOLING AND FROSTBITE.
INHALATION:
CARDIAC ARRHYTHMIA'S, NARCOTIC AND ANESTHETIC EFFECTS MAY BE SEEN.
INGESTION: NOT APPLICABLE; SUBSTANCE IS A GAS AT ROOM TEMPERATURE.
CHRONIC HEALTH EFFECTS: NONE KNOWN
OSHA HAZARD CLASSIFICATIONS: FLAMMABLE GAS, TARGET ORGAN
CARCINOGENICITY:
NOT CONSIDERED TO BE A CARCINOGEN BY EITHER OSHA, NTP, IARC, OR ACGIH
TARGET ORGANS: CENTRAL NERVOUS SYSTEM AND HEART.
| SECTION 4. FIRST AID MEASURES | |
EYE CONTACT:
FLUSH EYES WITH WATER FOR 15 MINUTES. REMOVE ANY CONTACT LENSES AND
CONTINUE TO FLUSH. OBTAIN MEDICAL ATTENTION.
SKIN CONTACT:
WASH THOROUGHLY WITH MILD SOAP AND LUKEWARM WATER. OBTAIN MEDICAL ATTENTION
IF IRRITATION DEVELOPS AND PERSISTS.
INGESTION:
EXCESSIVE EXPOSURE IS UNLIKELY BECAUSE SUBSTANCE IS A GAS AT ROOM
TEMPERATURE. CONTACT PHYSICIAN OR LOCAL POISON CONTROL CENTER IF ANY
UNUSUAL CONCERNS.
INHALATION:
REMOVE PATIENT TO FRESH AIR AND OBTAIN MEDICAL ATTENTION IF SYMPTOMS
DEVELOP.
| SECTION 5. FIRE FIGHTING MEASURES | |
FLASH POINT: -117 F
LEL: 1.8
UEL: 8.4
EXTINGUISHING MEDIA: CARBON DIOXIDE, DRY CHEMICAL FOR SMALL FIRES.
SPECIAL FIRE FIGHTING PROCEDURES:
USE WATER TO COOL FIRE EXPOSED CONTAINERS AND EQUIPMENT.
EXPLOSION HAZARDS:
GAS MAY TRAVEL CONSIDERABLE DISTANCES TO IGNITION SOURCE AND FLASH BACK.
| SECTION 6. ACCIDENTAL RELEASE MEASURES | |
REMOVE ANY SOURCES OF IGNITION. DISSIPATE VAPOR WITH WATER SPRAY. ABSORB
LIQUID ON VERMICULITE. VENTILATE AREA.
| SECTION 7. HANDLING AND STORAGE | |
AVOID ELEMENT BREAKAGE, SHARP KINKS AND BENDS IN CAPILLARY. AVOID OPEN
FLAMES.
| SECTION 8. EXPOSURE CONTROLS AND PERSONAL PROTECTION | |
VENTILATION: GENERAL.
RESPIRATORY PROTECTION: NONE REQUIRED.
EYE PROTECTION: RECOMMENDED IF EXPOSED TO POSSIBLE ELEMENT BREAKAGE.
HAND/CLOTHING PROTECTION:
RUBBER GLOVES NEEDED WHEN HANDLING THE LEAKING ELEMENT.
OTHER PROTECTIVE EQUIPMENT: NONE
| SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES | |
APPEARANCE: COLORLESS, ODORLESS GAS AT ROOM TEMPERATURE
BOILING POINT: 760 MM HG 10 F
EVAPORATION RATE: >1 (ETHYL ETHER=1)
SOLUBLE IN WATER: NEGLIGIBLE
SPECIFIC GRAVITY: 0.56 (60F/60F)
VAPOR DENSITY: 14.7 PSIA 21. @ 60 F
VAPOR PRESSURE: 3733 MM HG AT 100 F
VOLATILES: 100% BY VOLUME
| SECTION 10. STABILITY AND REACTIVITY | |
STABILITY: STABLE
REACTIVITY: HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
INCOMPATIBILITIES: OXYGEN AND STRONG OXIDIZING MATERIALS
HAZARDOUS DECOMPOSITION PRODUCTS: NONE
| SECTION 11. TOXICOLOGY INFORMATION | |
LD50 = 5045 MG/KG IN RATS; INHALATION
LC50 = 16000 PPM/8H IN RATS
| SECTION 12. ECOLOGICAL INFORMATION | |
NO DATA AVAILABLE
| SECTION 13. DISPOSAL CONSIDERATION | |
DISPOSE OF AS SOLID WASTE IN ACCORDANCE WITH LOCAL, STATE AND FEDERAL
REGULATIONS.
| SECTION 14. TRANSPORTATION INFORMATION | |
DOT CLASSIFICATION: FLAMMABLE GAS
| SECTION 15. REGULATORY INFORMATION | |
NONE
| SECTION 16. OTHER INFORMATION | |
THIS INFORMATION IS FURNISHED WITHOUT WARRANTY, EXPRESSED OR IMPLIED,
EXCEPT THAT IT IS ACCURATE TO THE BEST OF OUR KNOWLEDGE.
PREPARED BY:
PROSAR
1295 BANDANA BLVD
SUITE 335
ST PAUL, MN 55108
(651-917-6100)
ISOBUTANE FILL MATERIAL MSDS