| Common Name: | MINWOOL-1200 BOARD, FLEX, BLANKET, PIPE, SOUND ATTENUATION FIRE BATTS, SAFING |
| Manufacturer: | INDUSTRIAL INSULATION GROUP |
| SDS Revision Date: | 9/6/2005 |
| SDS Format: | No Format Specified |
| Item Number(s): | 3BE69 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
IIG
INDUSTRIAL INSULATION GROUP
A CALSILITE/JOHNS MANVILLE JOINT VENTURE
MATERIAL SAFETY DATA SHEET
DATE: 9/6/2005
MSDS ID: 20509
REV: 1.0.3
REPLACES: 4/1/2003
MATERIAL NAME: FIRE RESISTANT MINERAL WOOL INSULATION
| SECTION 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION |  |
PRODUCT NAME(S):
MINWOOL-1200(TM) BOARD, FLEX, BLANKET, PIPE, SOUND ATTENUATION FIRE BATTS,
SAFING, CURTAINWALL, PIPE AND TANK
MANUFACTURER INFORMATION:
INDUSTRIAL INSULATION GROUP MINWOOL
908 JOHN BUSSEY DRIVE
PHENIX CITY, AL 36869
WEBSITE: WWW.IIG-LLC.COM
TRADE NAMES: MINWOOL-1200
PHONE NUMBER FOR HEALTH AND SAFETY INFORMATION:
970.858.6211 (M-F, 7AM TO 4 PM, MOUNTAIN TIME)
| SECTION 2 - COMPOSITION AND INFORMATION ON INGREDIENTS | |
CAS # COMPONENT PERCENT OSHA ACGIH NIOSH
PEL TLV REL
65997-17-3 SYNTHETIC VITREOUS FIBER 95+ 15(T) 1F/CC NE
5(R) MG/M3
25104-55-6 CURED UREA 0-5 NE NE NE
FORMALDEHYDE/PHENOL
BINDER
ACGIH TLVS ARE 2003 VALUES. OSHA PELS ARE THOSE IN EFFECT ON THE DATE OF
PREPARATION OF THIS MSDS. THE LISTED PELS, TLVS AND RELS ARE TIME WEIGHTED
AVERAGE EXPOSURE LIMITS.
COMPONENT RELATED REGULATORY INFORMATION:
THIS PRODUCT MAY BE REGULATED, HAVE EXPOSURE LIMITS OR OTHER INFORMATION
IDENTIFIED AS THE FOLLOWING: NUISANCE PARTICULATES, ROCK WOOL FIBERS
| SECTION 3 - HAZARDS IDENTIFICATION | |
EMERGENCY OVERVIEW:
APPEARANCE AND ODOR:
COMMERCIAL BOARD, BATT, AND PIPE INSULATION IS SOLID, GREEN/YELLOW.
THIS PRODUCT IS AN ARTICLE AND UNDER NORMAL CONDITIONS OF USE, THIS PRODUCT
IS NOT EXPECTED TO CREATE ANY UNUSUAL EMERGENCY HAZARDS. HOWEVER, CUTTING,
SAWING, OR ABRADING MAY INCREASE THE RISK OF PERSONNEL EXPOSURE.
INHALATION OF EXCESSIVE AMOUNTS OF DUST CREATED WHEN FABRICATING, CUTTING,
OR OTHER MECHANICAL ALTERATIONS OF THE PRODUCT MAY CAUSE TEMPORARY UPPER
RESPIRATORY IRRITATION AND/OR CONGESTION - REMOVE AFFECTED INDIVIDUALS TO
FRESH AIR.
SKIN IRRITATION MAY BE TREATED BY GENTLY WASHING AFFECTED AREA WITH SOAP AND
WARM WATER.
EYE IRRITATION MAY BE TREATED BY FLUSHING EYES WITH LARGE AMOUNTS OF WATER.
IF IRRITATION PERSISTS, CONTACT A PHYSICIAN.
PROLONGED CONTACT WITH DUST FROM THIS PRODUCT MAY CAUSE DERMATITIS.
ACRID SMOKE MAY BE GENERATED IN A FIRE, USE NORMAL FIRE FIGHTING PROCEDURES
TO PREVENT INHALATION OF SMOKE AND GASES.
HMIS RATING:
HEALTH 0
FIRE 0
REACTIVITY 0
OTHER 0
NFPA RATING:
HEALTH 0
FLAMMABILITY 0
REACTIVITY 0
WHMIS CLASS: IIG MINWOOL-1200 PRODUCTS ARE NOT CONTROLLED PRODUCTS
POTENTIAL HEALTH EFFECTS:
SUMMARY:
BREATHING DUST FROM THIS PRODUCT MAY CAUSE A SCRATCHY THROAT, CONGESTION,
AND SLIGHT COUGHING.
GETTING DUST OR FIBERS ON THE SKIN, OR IN THE EYES MAY CAUSE ITCHING, RASH,
OR REDNESS.
BREATHING LARGE AMOUNTS OF DUST OR FIBERS FROM THIS PRODUCT MAY LEAD TO
CHRONIC HEALTH EFFECTS AS DISCUSSED IN SECTION 11 OF THIS MATERIAL SAFETY
DATA SHEET.
INHALATION:
IF INHALED, REMOVE THE AFFECTED PERSON TO FRESH AIR. IF IRRITATION PERSISTS,
SEEK MEDICAL ATTENTION.
SKIN CONTACT:
DUSTS AND FIBERS FROM THIS PRODUCT MAY CAUSE TEMPORARY MECHANICAL IRRITATION
TO THE SKIN.
EYE CONTACT:
DUSTS AND FIBERS FROM THIS PRODUCT MAY CAUSE TEMPORARY MECHANICAL IRRITATION
TO THE EYES.
INGESTION:
THIS PRODUCT IS NOT INTENDED TO BE INGESTED OR EATEN UNDER NORMAL CONDITIONS
OF USE. IF INGESTED, IT MAY CAUSE TEMPORARY IRRITATION TO THE
GASTROINTESTINAL (GI) TRACT, ESPECIALLY THE STOMACH.
TARGET ORGANS: UPPER RESPIRATORY PASSAGES, SKIN, AND EYES.
PRIMARY ROUTES OF ENTRY (EXPOSURE):
INHALATION (BREATHING DUST), SKIN, AND EYE CONTACT.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE:
CHRONIC RESPIRATORY OR SKIN CONDITIONS MAY TEMPORARILY WORSEN FROM EXPOSURE
TO THIS PRODUCT.
| SECTION 4 - FIRST AID MEASURE | |
FIRST AID:
INHALATION:
REMOVE TO FRESH AIR. DRINK WATER TO CLEAR THROAT, AND BLOW NOSE TO REMOVE
DUST. IF IRRITATION PERSISTS, GET MEDICAL ATTENTION.
FIRST AID:
SKIN:
WASH GENTLY WITH SOAP AND WARM WATER TO REMOVE DUST. USE A WASH CLOTH TO
HELP REMOVE FIBERS. TO AVOID FURTHER IRRITATION, DO NOT RUB OR SCRATCH
AFFECTED AREAS. RUBBING OR SCRATCHING MAY FORCE FIBERS INTO THE SKIN.
IF IRRITATION PERSISTS GET MEDICAL ATTENTION. NEVER USE COMPRESSED AIR TO
REMOVE FIBERS FROM THE SKIN. WASH HANDS BEFORE EATING OR USING THE RESTROOM.
FIRST AID:
INGESTION:
PRODUCT IS NOT INTENDED TO BE INGESTED OR EATEN. IF THIS PRODUCT IS
INGESTED, IRRITATION OF THE GASTROINTESTINAL (GI) TRACT MAY OCCUR, AND
SHOULD BE TREATED SYMPTOMATICALLY. WATCH THE PERSON FOR SEVERAL DAYS TO MAKE
SURE THAT PARTIAL OR COMPLETE INTESTINAL OBSTRUCTION DOES NOT OCCUR. DO NOT
INDUCE VOMITING UNLESS DIRECTED TO DO SO BY MEDICAL PERSONNEL. RINSE MOUTH
WITH WATER TO REMOVE FIBERS, AND DRINK PLENTY OF WATER TO HELP REDUCE THE
IRRITATION. NO CHRONIC EFFECTS ARE EXPECTED FOLLOWING INGESTION.
FIRST AID:
EYES:
DO NOT RUB OR SCRATCH YOUR EYES. FIBERS MAY CAUSE THE EYE TO BE SCRATCHED.
FLUSH EYES WITH LARGE AMOUNTS OF WATER FOR AT LEAST 15 MINUTES. IF
IRRITATION PERSISTS, CONTACT A MEDICAL PROFESSIONAL.
FIRST AID:
NOTES TO PHYSICIAN:
THIS PRODUCT IS A MECHANICAL IRRITANT, AND IS NOT EXPECTED TO PRODUCE ANY
CHRONIC HEALTH EFFECTS FROM ACUTE EXPOSURES. TREATMENT SHOULD BE DIRECTED
TOWARD REMOVING THE SOURCE OF IRRITATION WITH SYMPTOMATIC TREATMENT AS
NECESSARY.
| SECTION 5 - FIRE FIGHTING MEASURES | |
FLASH POINT: NOT APPLICABLE
METHOD USED: NOT APPLICABLE
UPPER FLAMMABLE LIMIT (UFL): NOT APPLICABLE
LOWER FLAMMABLE LIMIT (LFL): NOT APPLICABLE
AUTO IGNITION: NOT DETERMINED
FLAMMABILITY CLASSIFICATION: NON COMBUSTIBLE
RATE OF BURNING: NOT APPLICABLE
GENERAL FIRE HAZARD: THERE IS NO POTENTIAL FOR FIRE OR EXPLOSION.
EXTINGUISHING MEDIA:
USE ANY EXTINGUISHING MEDIA APPROPRIATE FOR THE SURROUNDING FIRES
FIRE FIGHTING EQUIPMENT/INSTRUCTIONS:
NO SPECIAL PROCEDURES ARE EXPECTED TO BE NECESSARY FOR THIS PRODUCT. NORMAL
FIRE FIGHTING PROCEDURES SHOULD BE FOLLOWED TO AVOID INHALATION OF SMOKE AND
GASES PRODUCED BY OTHER MATERIALS.
HAZARDOUS COMBUSTION PRODUCTS:
PRIMARY COMBUSTION PRODUCTS ARE CARBON MONOXIDE, CARBON DIOXIDE, AMMONIA,
AND WATER. OTHER UNDETERMINED COMPOUNDS COULD BE RELEASED IN SMALL
QUANTITIES.
| SECTION 6 - ACCIDENTAL RELEASE MEASURES | |
CONTAINMENT PROCEDURES:
PICK UP LARGE PIECES. VACUUM DUSTS. IF SWEEPING IS NECESSARY, USE A DUST
SUPPRESSANT SUCH AS WATER. DO NOT DRY SWEEP DUST ACCUMULATION OR USE
COMPRESSED AIR FOR CLEAN-UP. THESE PROCEDURES WILL HELP TO MINIMIZE
POTENTIAL EXPOSURES. THIS MATERIAL WILL SINK AND DISPERSE ALONG THE BOTTOM
OF WATERWAYS AND PONDS. IT CAN NOT EASILY BE REMOVED AFTER IT IS WATERBORNE;
HOWEVER, THE MATERIAL IS NON-HAZARDOUS IN WATER.
CLEAN-UP PROCEDURES:
WASTES ARE NOT HAZARDOUS AS DEFINED BY THE RCRA (40 CFR 261). COMPLY WITH
STATE AND LOCAL REGULATIONS FOR DISPOSAL OF THESE PRODUCTS. IF YOU ARE
UNSURE OF THE REGULATIONS, CONTACT YOUR LOCAL PUBLIC HEALTH DEPARTMENT,
OR THE LOCAL OFFICE OF THE EPA.
| SECTION 7 - HANDLING AND STORAGE | |
HANDLING PROCEDURES:
USE PROTECTIVE EQUIPMENT AS DESCRIBED IN SECTION 8 OF THIS MATERIAL SAFETY
DATA SHEET WHEN HANDLING UNCONTAINED MATERIAL. KEEP PRODUCT IN ITS
PACKAGING, AS LONG AS PRACTICABLE TO MINIMIZE POTENTIAL DUST GENERATION.
KEEP WORK AREAS CLEAN. AVOID UNNECESSARY HANDLING OF SCRAP MATERIALS BY
PLACING THEM IN WASTE DISPOSAL CONTAINERS AND EQUIPMENT, KEPT AS TO CLOSE
WORKING AREAS AS POSSIBLE, TO PREVENT RELEASE OF FIBERS AND DUST. GOOD
HOUSEKEEPING PRACTICES SHOULD BE USED TO PREVENT GENERATION AND ACCUMULATION
OF DUSTS. AFTER HANDLING PRODUCT, WASH FACE AND HANDS BEFORE EATING,
DRINKING, OR SMOKING.
STORAGE PROCEDURES:
WAREHOUSE STORAGE SHOULD BE IN ACCORDANCE WITH PACKAGE DIRECTIONS, IF ANY.
MATERIAL SHOULD BE KEPT DRY, AND PROTECTED FROM THE ELEMENTS.
| SECTION 8 - EXPOSURE CONTROL AND PERSONAL PROTECTION | |
GENERAL PRODUCT INFORMATION:
FOLLOW ALL APPLICABLE EXPOSURE LIMITS AND USE OSHA-RECOMMENDED EQUIPMENT AND
WORK PRACTICES. A COMPLETE COPY OF THESE PRACTICES CAN BE OBTAINED FROM IIG
MINWOOL LLC (SEE SECTION 1 OF THIS MATERIAL SAFETY DATA SHEET), AND IS ALSO
AVAILABLE ON THE OSHA WEBSITE
(HTTP://WWW.OSHA.GOV/SLTC/SYNTHETICMINERALFIBERS).
PERSONAL PROTECTIVE EQUIPMENT:
PERSONAL PROTECTIVE EQUIPMENT:
EYES/FACE:
SAFETY GLASSES WITH SIDE SHIELDS ARE RECOMMENDED TO KEEP DUST OUT OF THE
EYES.
PERSONAL PROTECTIVE EQUIPMENT:
SKIN:
LEATHER OR COTTON GLOVES SHOULD BE WORN TO PREVENT SKIN CONTACT AND
IRRITATION. BARRIER CREAMS MAY ALSO BE USED TO REDUCE SKIN CONTACT AND
IRRITATION CAUSED BY MINERAL WOOL FIBERS. NORMAL WORK CLOTHING
(LONG SLEEVED SHIRTS AND LONG PANTS) IS RECOMMENDED. SKIN IRRITATION IS
KNOWN TO OCCUR CHIEFLY AT THE PRESSURE POINTS SUCH AS AROUND THE NECK,
WRISTS, WAIST AND BETWEEN THE FINGERS.
PERSONAL PROTECTIVE EQUIPMENT:
RESPIRATORY:
A RESPIRATOR SHOULD BE USED IF VENTILATION IS UNAVAILABLE, OR IS INADEQUATE
FOR KEEPING DUST AND FIBER LEVELS BELOW THE APPLICABLE EXPOSURE LIMITS.
IN THOSE CASES, USE A NIOSH-CERTIFIED DISPOSABLE OR REUSABLE PARTICULATE
RESPIRATOR WITH AN EFFICIENCY RATING OF N95 OR HIGHER (UNDER 42 CFR 84) WHEN
WORKING WITH THIS PRODUCT, FOR EXPOSURES UP TO FIVE TIMES THE ESTABLISHED
EXPOSURE LIMITS USE A QUARTER-MASK RESPIRATOR, RATED N95 OR HIGHER; AND FOR
EXPOSURES UP TO TEN TIMES THE ESTABLISHED EXPOSURE LIMITS USE A HALF-MASK
RESPIRATOR (E.G., MSA'S DM-11, RACAL'S DELTA N95, 3M'S 8210), RATED N95 OR
HIGHER.
OPERATIONS SUCH AS SAWING, BLOWING, TEAR OUT, AND SPRAYING MAY GENERATE
AIRBORNE FIBER CONCENTRATIONS REQUIRING A HIGHER LEVEL OF RESPIRATORY
PROTECTION. FOR EXPOSURES UP TO 50 TIMES THE ESTABLISHED EXPOSURE LIMITS
USE A FULL-FACE RESPIRATOR, RATED N99 OR HIGHER.
VENTILATION:
IN FIXED MANUFACTURING SETTINGS, LOCAL EXHAUST VENTILATION SHOULD BE
PROVIDED AT AREAS OF CUTTING TO REMOVE AIRBORNE DUST AND FIBERS. GENERAL
DILUTION VENTILATION SHOULD BE PROVIDED AS NECESSARY TO KEEP AIRBORNE DUST
AND FIBERS BELOW THE APPLICABLE EXPOSURE LIMITS AND GUIDELINES. THE NEED FOR
VENTILATION SYSTEMS SHOULD BE EVALUATED BY A PROFESSIONAL INDUSTRIAL
HYGIENIST, WHILE THE DESIGN OF SPECIFIC VENTILATION SYSTEMS SHOULD BE
CONDUCTED BY A PROFESSIONAL ENGINEER.
PERSONAL PROTECTIVE EQUIPMENT:
GENERAL:
LOOSE-FITTING, LONG-SLEEVED CLOTHING SHOULD BE WORN TO PROTECT THE SKIN FROM
IRRITATION, EXPOSED SKIN AREAS SHOULD BE WASHED WITH SOAP AND WARM WATER
AFTER HANDLING.
| SECTION 9 - PHYSICAL & CHEMICAL PROPERTIES | |
APPEARANCE: FIBROUS SEMI-CIRCLE, BLANKET, OR BOARD INSULATION.
ODOR: ORGANIC
pH: NOT APPLICABLE
PHYSICAL STATE: SOLID
VAPOR DENSITY: NOT APPLICABLE
VAPOR PRESSURE: NOT APPLICABLE
MELTING POINT: NOT DETERMINED
BOILING POINT: NOT APPLICABLE
SPECIFIC GRAVITY: NOT DETERMINED
SOLUBILITY (H2O): NIL
FREEZING POINT: NOT APPLICABLE
VISCOSITY: NOT APPLICABLE
EVAPORATION RATE: NOT APPLICABLE
VOC: NOT APPLICABLE
PERCENT VOLATILE: 0
| SECTION 10 - CHEMICAL STABILITY & REACTIVITY INFORMATION | |
CHEMICAL STABILITY: THIS IS A STABLE MATERIAL. THIS PRODUCT IS NOT REACTIVE.
HAZARDOUS DECOMPOSITION: NONE.
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR.
INCOMPATIBLE MATERIALS: THIS PRODUCT REACTS WITH HYDROFLUORIC ACID.
HAZARDOUS DECOMPOSITION PRODUCTS:
PRIMARY COMBUSTION PRODUCTS ARE CARBON MONOXIDE, CARBON DIOXIDE, AMMONIA,
AND WATER. OTHER UNDETERMINED COMPOUNDS COULD BE RELEASED IN SMALL
QUANTITIES.
| SECTION 11 - TOXICOLOGICAL INFORMATION | |
ACUTE TOXICITY:
A:
GENERAL PRODUCT INFORMATION:
DUSTS MAY CAUSE MECHANICAL IRRITATION TO EYES AND SKIN. INGESTION MAY CAUSE
TRANSIENT IRRITATION OF THROAT, STOMACH AND GASTROINTESTINAL TRACT.
INHALATION MAY CAUSE COUGHING, NOSE AND THROAT IRRITATION, AND SNEEZING.
HIGHER EXPOSURES MAY CAUSE DIFFICULTY BREATHING, CONGESTION, AND CHEST
TIGHTNESS.
B:
COMPONENT ANALYSIS - LD50/LC50:
NO LD50/LC50'S ARE AVAILABLE FOR THIS PRODUCT.
CARCINOGENICITY:
A:
GENERAL PRODUCT INFORMATION:
OSHA, NTP, IARC, AND ACGIH HAVE NOT CLASSIFIED THIS PRODUCT IN ITS ENTIRETY
AS A CARCINOGEN.
B:
COMPONENT ANALYSIS - LD50/LC50:
CURED UREA/FORMALDEHYDE/PHENOL BINDER (25104-55-6):
ORAL LD50 RAT: 7 GM/KG
ORAL LD50 MOUSE: 7 GM/KG
CARCINOGENICITY:
A:
GENERAL PRODUCT INFORMATION:
IN OCTOBER 2001 THE IARC CONCLUDED ITS RE-EVALUATION OF THE CARCINOGENIC
RISK OF MINERAL WOOL FIBERS. THE RESULT WAS A CLASSIFICATION OF THE FIBERS
FROM GROUP 2B (POSSIBLY CARCINOGENIC TO HUMANS) TO GROUP 3 (NOT CLASSIFIABLE
AS TO THE CARCINOGENICITY TO HUMANS). EPIDEMIOLOGICAL STUDIES PUBLISHED
DURING THE 15 YEARS PRIOR TO THE 2001 IARC REVIEW PROVIDE NO EVIDENCE OF
INCREASED RISK OF CANCER FROM OCCUPATIONAL EXPOSURE DURING MANUFACTURE OR
USE OF MINERAL WOOL FIBER.
B:
COMPONENT CARCINOGENICITY:
ACGIH, IARC, OSHA, AND NTP CARCINOGEN LISTS HAVE BEEN CHECKED FOR THOSE
COMPONENTS WITH CAS REGISTRY NUMBERS.
SYNTHETIC VITREOUS FIBER (65997-17-3):
ACGIH:
A3 - ANIMAL CARCINOGEN (RELATED TO ROCK WOOL FIBERS) WITH UNKNOWN RELEVANCE
TO HUMANS
IARC:
MONOGRAPH 43, 1988 (RELATED TO GLASS FILAMENTS) (GROUP 3 (NOT CLASSIFIABLE))
| SECTION 12 - ECOLOGICAL INFORMATION | |
ECOTOXICITY:
A:
GENERAL PRODUCT INFORMATION: NO DATA AVAILABLE FOR THIS PRODUCT.
B:
COMPONENT ANALYSIS - ECOTOXICITY - AQUATIC TOXICITY:
NO ECOTOXICITY DATA ARE AVAILABLE FOR THIS PRODUCT'S COMPONENTS.
| SECTION 13 - DISPOSAL CONSIDERATIONS | |
US EPA WASTE NUMBER & DESCRIPTIONS:
A:
GENERAL PRODUCT INFORMATION:
THIS PRODUCT, AS SUPPLIED, IS NOT REGULATED AS A HAZARDOUS WASTE BY THE
U.S. EPA UNDER RCRA REGULATIONS.
COMPLY WITH STATE AND LOCAL REGULATIONS FOR DISPOSAL. IF YOU ARE UNSURE OF
THE REGULATIONS, CONTACT YOUR LOCAL PUBLIC HEALTH DEPARTMENT, OR THE LOCAL
OFFICE OF THE EPA.
B:
COMPONENT WASTE NUMBERS:
NO EPA WASTE NUMBERS ARE APPLICABLE FOR THIS PRODUCT'S COMPONENTS.
DISPOSAL INSTRUCTIONS:
DISPOSE OF WASTE MATERIAL ACCORDING TO LOCAL, STATE, FEDERAL, AND PROVINCIAL
ENVIRONMENTAL REGULATIONS.
| SECTION 14 - TRANSPORT INFORMATION | |
US DOT INFORMATION:
SHIPPING NAME:
THIS PRODUCT IS NOT CLASSIFIED A HAZARDOUS MATERIAL FOR TRANSPORT.
| SECTION 15 - REGULATORY INFORMATION | |
US FEDERAL REGULATIONS:
A:
GENERAL PRODUCT INFORMATION:
NO INFORMATION ON THIS PRODUCT AS A WHOLE. FORMALDEHYDE CONTENT IS BELOW THE
SARA 313 0.1% 'DE MINIMIS CONCENTRATION.
B:
COMPONENT ANALYSIS:
THIS MATERIAL CONTAINS ONE OR MORE OF THE FOLLOWING CHEMICALS REQUIRED TO BE
IDENTIFIED UNDER SARA SECTION 302 (40 CFR 355 APPENDIX A), SARA SECTION 313
(40 CFR 372.65) AND/OR CERCLA (40 CFR 302.4).
SYNTHETIC VITREOUS FIBER (65997-17-3):
CERCLA:
INCLUDES MINERAL FIBER EMISSIONS FROM FACILITIES MANUFACTURING OR PROCESSING
GLASS ROCK OR SLAG FIBERS (OR OTHER MINERAL DERIVED FIBERS) OF AVERAGE
DIAMETER 1 MICROMETER OR LESS; STATUTORY RQ = 1 POUND (.454 KG); NO FINAL RQ
IS BEING ASSIGNED TO THE GENERIC OR BROAD CLASS (RELATED TO FINE MINERAL
FIBERS)
STATE REGULATIONS:
A:
GENERAL PRODUCT INFORMATION:
THE FOLLOWING STATEMENT(S) ARE PROVIDED UNDER THE CALIFORNIA SAFE DRINKING
WATER AND TOXIC ENFORCEMENT ACT OF 1986 (PROPOSITION 65):
WARNING!
THIS PRODUCT CONTAINS A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE
CANCER.
OTHER REGULATORY INFORMATION:
A:
GENERAL PRODUCT INFORMATION: NO INFORMATION AVAILABLE FOR THE PRODUCT.
B:
TSCA STATUS:
ALL INGREDIENTS OF THIS PRODUCT ARE INCLUDED IN THE US EPA CHEMICAL
SUBSTANCE INVENTORY OR ARE NOT REQUIRED TO BE LISTED.
C:
CERCLA:
INCLUDES MINERAL FIBER EMISSIONS FROM FACILITIES MANUFACTURING OR PROCESSING
GLASS ROCK OR SLAG FIBERS (OR OTHER MINERAL DERIVED FIBERS) OF AVERAGE
DIAMETER 1 MICROMETER OR LESS
STATUTORY RQ: 1 POUND (.454 KG)
NO FINAL RQ IS BEING ASSIGNED TO THE GENERIC OR BROAD CLASS (RELATED TO FINE
MINERAL FIBERS).
D:
CLEAN AIR ACT:
MINERAL WOOL FIBER APPEARS ON THE CLEAN AIR ACT-1990 HAZARDOUS AIR
POLLUTANTS LIST.
INTERNATIONAL REGULATIONS:
A:
GENERAL PRODUCT INFORMATION:
CANADA WORKPLACE HAZARDOUS MATERIALS INFORMATION SYSTEM (WHMIS):
WHMIS CLASSIFICATION: D2B - IRRITANT
PRODUCT CLASSIFIED AS A MANUFACTURED ARTICLE AS DEFINED IN HAZARDOUS PRODUCT
ACT (HPA), SECTION 11(1). SECTION 12(1) EXEMPTS IT FROM THE WHMIS SUPPLIER
LABEL AND MSDS REQUIREMENTS OF THE ACT.
B:
COMPONENT ANALYSIS - WHMIS IDL: NO COMPONENTS ARE LISTED IN THE WHMIS IDL.
| SECTION 16 - OTHER INFORMATION | |
INFORMATION ABOUT "HEALTH AND SAFETY RESEARCH ON ROCK- AND SLAG-WOOL" CAN BE
OBTAINED FROM THE NORTH AMERICAN INSULATION MANUFACTURERS ASSOCIATION
(NAIMA), 44 CANAL CENTER PLAZA, SUITE 310, ALEXANDRIA, VA 22314, OR ON THE
WEB AT HTTP://WWW.NAIMA.ORG
THIS PRODUCT HAS BEEN CLASSIFIED ACCORDING TO THE HAZARD CRITERIA OF THE CPR
AND THE MSDS CONTAINS ALL THE INFORMATION REQUIRED BY THE CPR.
KEY/LEGEND:
EPA = ENVIRONMENTAL PROTECTION AGENCY
TSCA = TOXIC SUBSTANCE CONTROL ACT
ACGIH = AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
IARC = INTERNATIONAL AGENCY FOR RESEARCH ON CANCER
NIOSH = NATIONAL INSTITUTE FOR OCCUPATIONAL SAFETY AND HEALTH
NTP = NATIONAL TOXICOLOGY PROGRAM
OSHA = OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION
NFPA = NATIONAL FIRE PROTECTION ASSOCIATION
HMIS = HAZARDOUS MATERIAL IDENTIFICATION SYSTEM
RCRA = RESOURCE CONSERVATION AND RECOVERY ACT
CERCLA =
COMPREHENSIVE ENVIRONMENTAL RESPONSE, COMPENSATION AND LIABILITY ACT
SARA = SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT
DSL = CANADIAN DOMESTIC SUBSTANCE LIST
EINECS = EUROPEAN INVENTORY OF NEW AND EXISTING CHEMICAL SUBSTANCES
WHMIS = WORKPLACE HAZARDOUS MATERIALS INFORMATION SYSTEM
CAA = CLEAN AIR ACT
CHPA = CANADIAN HAZARDOUS PRODUCT ACT
IDL = CANADIAN HAZARDOUS DISCLOSURE LIST
REVISION SUMMARY:
THIS IS A REVISED MSDS WHICH REPLACES REVISION 1.0.2 WITH NEW FORMATTING AND
UPDATED EXPOSURE INFORMATION. A NEW ID NUMBER WAS ASSIGNED TO THIS DOCUMENT
TO BE CONSISTENT WITH OTHER IIG DOCUMENTS.
GET THIS AND OTHER MSDS FORMS ELECTRONICALLY VIA INTERNET:
HTTP://WWW.IIG-LLC.COM.
AS OF THE DATE OF PREPARATION OF THIS DOCUMENT, THE FOREGOING INFORMATION IS
BELIEVED TO BE ACCURATE AND IS PROVIDED IN GOOD FAITH TO COMPLY WITH
APPLICABLE FEDERAL AND STATE LAW(S). HOWEVER, NO WARRANTY OR REPRESENTATION
WITH RESPECT TO SUCH INFORMATION IS INTENDED OR GIVEN.
IMPORTANT SAFETY NOTICE:
THE INFORMATION IN THIS MSDS RELATES ONLY TO THE SPECIFIC MATERIAL DESCRIBED
HEREIN AND DOES NOT RELATE TO USE IN COMBINATION WITH ANY OTHER MATERIAL OR
SUBSTANCE OR IN ANY PROCESS. BECAUSE OF THE USE OF THIS INFORMATION AND THE
CONDITIONS OF USE OF THIS PRODUCT ARE NOT WITHIN THE CONTROL OF INDUSTRIAL
INSULATION GROUP, IT IS THE USERS OBLIGATION TO DETERMINE THE CONDITIONS OF
SAFE USE OF THIS PRODUCT. USERS OF THIS PRODUCT SHOULD STUDY THIS MSDS AND
BECOME AWARE OF THE PRODUCT HAZARDS AND SAFETY INFORMATION BEFORE USING THIS
PRODUCT. USERS SHOULD ALSO NOTIFY THEIR EMPLOYEES, AGENTS, AND CONTRACTORS
REGARDING INFORMATION CONTAINED IN THIS MSDS AND ANY PRODUCT HAZARDS AND
SAFETY INFORMATION IN ORDER TO PROVIDE FOR SAFE USE OF THIS PRODUCT.
IIG 20509