| Common Name: | ABRASIVE FLAP DISC - POLYMER BACKED (PHENOLIC) |
| Manufacturer: | WEILER |
| SDS Revision Date: | 5/2/2006 |
| SDS Format: | No Format Specified |
| Item Number(s): | 4KM65, 4KM66, 4KM67, 4KM68, 4KM69, 4KM70 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
MSDS
ABRASIVE FLAP DISC - POLYMER BACKED (PHENOLIC)
| SECTION I |  |
MANUFACTURER'S NAME: WEILER CORPORATION
ADDRESS:
ONE WEILER DRIVE
CRESCO, PA 18326
EMERGENCY TELEPHONE NUMBER: (570) 595-7495
TELEPHONE NUMBER FOR INFORMATION: (570) 595-7495
DATE PREPARED: MAY 2, 2006
NAME OF PREPARER: FRANK HETTES
| SECTION II - HAZARDOUS INGREDIENTS / IDENTITY INFORMATION | |
HAZARDOUS COMPONENTS, CAS# OSHA ACGIH OTHER %
(SPECIFIC CHEMICAL PEL TL LIMITS (OPTIONAL)
IDENTITY, COMMON
NAME(S)
AL2O3 15 MG/M3 5 MG/M3 18%
(ALUMINUM OXIDE)
ZRO2 5 MG/M3 5 MG/M3 18%
(ZIRCONIUM OXIDE)
EPOXY RESIN N.I. N.I. 5%
(BASED ON A BLEND
OF BISPHENOL-A &
BISPHENOL-F)
CACO3 N.I. N.I. 1%
(CALCIUM CARBONATE)
COTTON N.I. N.I. 10%
POLYMERS:
CARBON BLACK 1333-86-4 3.5 3.5 5%
MG/M3 MG/M3
GLASS 65997-17-3 10 MG/M3 11%
NYLON 6 25038-54-4 32%
| SECTION III - PHYSICAL / CHEMICAL CHARACTERISTICS | |
BOILING POINT: **N/A
VAPOR PRESSURE (MMHg.): **N/A
VAPOR DENSITY (AIR=1): **N/A
SOLUBILITY IN WATER: THE PAPER LABEL HAS SLIGHT WATER SOLUBILITY
SPECIFIC GRAVITY (H2O=1): >1
MELTING POINT: 400-500 DEGREES FAHRENHEIT
EVAPORATION RATE (BUTYL ACETATE=1): **N/A
APPEARANCE AND ODOR:
SOLID POLYMER DISC COATED WITH FLAPS OF ABRASIVE CLOTH; NO ODOR.
| SECTION IV - FIRE AND EXPLOSION HAZARD DATA | |
FLASH POINT (METHOD USED): **N/A
FLAMMABLE LIMITS: 200 DEGREES C
LEL: **N/A
UEL: **N/A
EXTINGUISHING MEDIA: ANY STANDARD EXTINGUISHING MEDIA (WATER AND FOAM)
SPECIAL FIRE FIGHTING PROCEDURES:
APPROVED PRESSURE DEMAND BREATHING APPARATUS AND PROTECTIVE CLOTHING SHOULD
BE USED FOR ALL FIRES. WATER SPRAY IS THE PREFERRED EXTINGUISHING MEDIUM.
THIS PRODUCT WILL MELT BUT WILL NOT BE CARRIED ON THE SURFACE OF WATER.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
HAZARDOUS COMBUSTION PRODUCTS MAY INCLUDE INTENSE HEAT, DENSE BLACK SMOKE,
CARBON MONOXIDE, HYDROGEN CYANIDE, AMMONIA, ALDEHYDES AND CARBON DIOXIDE.
| SECTION V - REACTIVITY DATA | |
STABILITY: STABLE
CONDITIONS TO AVOID: **N/A
INCOMPATIBILITY (MATERIALS TO AVOID): **N/A
HAZARDOUS DECOMPOSITION OR BYPRODUCTS:
DURING USE, GRINDING DUST IS GENERATED AND MAY PRODUCE DUST THAT IS AN
EXPLOSION OR RESPIRATORY HAZARD.
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR
| SECTION VI - HEALTH HAZARD DATA | |
PRIMARY HEALTH HAZARDS FIRST AID AND
ROUTE(S) (ACUTE AND CHRONIC) MEDICAL INFORMATION
OF ENTRY
INHALATION MAY CAUSE COUGHING, SHORTNESS OF REMOVE TO FRESH AIR. SEEK
BREATH. MEDICAL ADVICE IF CHRONIC.
INGESTION INGESTION VERY UNLIKELY AND NOT SEEK MEDICAL ADVICE.
RECOMMENDED.
SKIN MAY CAUSE ABRASIONS. OBTAIN FIRST AID.
DUST MAY CAUSE SKIN IRRITATION WASH WITH SOAP AND WATER.
EYES DUST MAY IRRITATE EYES. WASH WITH WATER.
SEEK MEDICAL ADVICE.
CARCINOGENICITY: NOT KNOWN
| SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE | |
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
NO SPECIAL PROCEDURES; STANDARD CLEAN-UP.
WASTE DISPOSAL METHOD:
STANDARD LANDFILL METHODS CONSISTENT WITH APPLICABLE FEDERAL, STATE AND
LOCAL LAWS.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE:
HANDLE WITH CARE, AVOID IMPACT; STORE DRY AT 20 DEGREES C +/- 20 C; 55-60%
AIR HUMIDITY.
OTHER PRECAUTIONS:
NORMAL PRECAUTIONS FOR NUISANCE DUST AND PARTICULATES GENERATED DURING
GRINDING.
| SECTION VIII - CONTROL MEASURES | |
RESPIRATORY PROTECTION (SPECIFY TYPE):
USE APPROVED RESPIRATORY PROTECTION FOR NUISANCE DUST.
VENTILATION:
LOCAL EXHAUST: REQUIRED
MECHANICAL (GENERAL): RECOMMENDED
SPECIAL: RESPIRATORY PROTECTION
OTHER: **N/A
PROTECTIVE GLOVES: RECOMMENDED
EYE PROTECTION: MANDATORY
OTHER PROTECTIVE CLOTHING OR EQUIPMENT:
HEARING PROTECTION & FACE SHIELD RECOMMENDED; KEEP MACHINE GUARDS IN PLACE.
WORK/HYGIENIC PRACTICES: **N/A
**N/A = NOT APPLICABLE
ALL RIGHTS RESERVED, COPYRIGHT (C) WEILER CORPORATION 1998-2007