| Common Name: | FIBER GLASS WOOL COMMERCIAL & INDUSTRIAL INSULATION |
| Manufacturer: | JOHNS MANVILLE |
| SDS Revision Date: | 6/26/2007 |
| SDS Format: | No Format Specified |
| Item Number(s): | 4JA15, 4JA16 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
JM
JOHNS MANVILLE
MATERIAL NAME: FIBER GLASS WOOL COMMERCIAL & INDUSTRIAL INSULATION
SAFETY DATA SHEET
ID: 1009
| SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION |  |
HAZARD LABEL: WARNING LABEL
COMPANY INFORMATION:
JOHNS MANVILLE
INSULATION SYSTEMS
P.O. BOX 5108
DENVER, CO 80127
USA
TELEPHONE: 303-978-2000 8:00AM-5:00PM M-F
EMERGENCY: 800-424-9300 (CHEMTREC, IN ENGLISH)
INTERNET ADDRESS: HTTP://WWW.JM.COM
TRADE NAMES:
1000 SERIES SPIN GLAS(R*) BOARD
800 SERIES SPIN-GLAS(R*) BOARD INSULATIONS
BLENDED BLOWING WOOL
FABRICATION BOARD
GROOVED DUCT BOARD
HULLBOARD (INCOMBUSTIBLE)
HULLINSUL(R*) FIBER GLASS BOARD
INCOMBUSTIBLE MICROLITE(R*)
INSUL-SHIELD(R*) COATED BLACK
LINACOUSTIC(R*) RC
MAT-FACED MICRO-AIRE(R*) DUCT BOARD
MICRO-FLEX(TM) LARGE DIAMETER PIPE AND TANK WRAP
MICRO-LOK(R*) HP
MICRO-LOK(R*) PIPE INSULATION
MICROMAT RX(TM)
PERMACOTE(R*) LINACOUSTIC(R*) (TYPES: STANDARD, HP, AND R-300)
PRECIPITATOR SPIN GLAS(R*)
R SERIES MICROLITE(R*) (PLAIN, FSK, PSK, & VINYL FACED)
SPIRACOUSTIC(TM)
SPIN GLAS(R*) HTB 26 & 23
SPIROCOUSTIC PLUS(TM)
SUPERDUCT(TM) BOARDS
SUPERDUCT(TM) RC BOARDS
ZESTON HI-LO TEMP(R*) INSULATION INSERTS
| SECTION 2 - COMPOSITION / INFORMATION ON INGREDIENTS | |
CAS # COMPONENT PERCENT
NOT APPLICABLE CONTINUOUS FILAMENT GLASS FIBER 1-10**
NOT APPLICABLE FIBER GLASS WOOL 50-98
NOT AVAILABLE NON-WOVEN, AP, FSK, PSK, OR VINYL FACINGS; 0-40
OR VINYL, ACRYLIC, OR LATEX COATINGS
NOT AVAILABLE UREA EXTENDED PHENOL-FORMALDEHYDE BINDER (CURED) 2-18*
NOT AVAILABLE UREA EXTENDED PHENOL-MELAMINE FORMALDEHYDE 2-18*
BINDER (CURED)
NOT AVAILABLE ACRYLIC COATING (PRESENT IN MAT-FACED 0-10
MICRO-AIRE DUCT BOARD ONLY)
25038-59-9 POLYESTER FIBER (PRESENT IN BLACK PRODUCTS ONLY) 1-10
NOT AVAILABLE METHYLENE DIUREA <2
50-00-0 FORMALDEHYDE <1
25637-99-4 CYCLODODECANE, HEXABROMO- (PRESENT IN <1
SPIRACOUSTIC ONLY)
1333-86-4 CARBON BLACK (PRESENT IN BLACK PRODUCTS ONLY) <1
1309-64-4 ANTIMONY TRIOXIDE 0.1-3***
* BINDER MAY BE EITHER OF THESE.
** COMPONENT SCRIM FACINGS
*** NOTE:
ANTIMONY TRIOXIDE (FIRE RETARDANT) MAY BE PRESENT IN THE FACINGS AND/OR
ADHESIVES. OCCUPATIONAL EXPOSURE TO AIRBORNE ANTIMONY TRIOXIDE IS NOT
EXPECTED TO OCCUR DUE TO PRODUCT FORM(S) AND INTENDED USE(S). EXPOSURE
LIMIT IS GIVEN FOR REFERENCE ONLY.
FREE FORMALDEHYDE RELEASED ONLY WITH HIGH TEMPERATURE AND HUMIDITY.
TEMPERATURES >32 DEG. C/90 DEG. F.
| SECTION 3 - HAZARDS IDENTIFICATION | |
EMERGENCY OVERVIEW:
APPEARANCE AND ODOR:
GOLD, YELLOW, OR BLACK FIBROUS GLASS BLANKET, BOARD, OR FORMED SHAPE WITH
OR WITHOUT FACINGS. NO SIGNIFICANT ODOR.
INHALATION OF EXCESSIVE AMOUNTS OF DUST FROM THE PRODUCT MAY CAUSE
TEMPORARY UPPER RESPIRATORY IRRITATION AND/OR CONGESTION-REMOVE INDIVIDUAL
TO FRESH AIR.
POTENTIAL HEALTH EFFECTS:
SUMMARY:
BREATHING DUST FROM THIS PRODUCT MAY CAUSE A SCRATCHY THROAT, CONGESTION,
AND SLIGHT COUGHING. GETTING DUST OR FIBERS ON THE SKIN, OR IN THE EYES MAY
CAUSE ITCHING, RASH, OR REDNESS. ADDITIONAL HEALTH AND SAFETY INFORMATION
IS PROVIDED IN SECTION 11 OF THIS MATERIAL SAFETY DATA SHEET.
IN HIGH TEMPERATURE APPLICATIONS, TREATMENT, CURING, OR IN GEOGRAPHIC AREAS
OF HIGH HEAT AND HUMIDITY, THIS PRODUCT MAY RELEASE GASES IRRITATING TO THE
EYES, NOSE AND THROAT. IN CONFINED OR POORLY VENTILATED AREAS, USE AIR
SUPPLIED RESPIRATORS DURING THE FIRST HEAT-UP CYCLES.
INHALATION:
IRRITATION OF THE UPPER RESPIRATORY TRACT, COUGHING, AND CONGESTION MAY
OCCUR IN EXTREME EXPOSURES. SEVERE IRRITATION OF THE MOUTH, NOSE, AND
THROAT, AS WELL AS SIGNS OF CENTRAL NERVOUS SYSTEM DEPRESSION (DROWSINESS,
DIZZINESS, HEADACHE), MAY OCCUR UPON INHALATION OF VAPORS OR GASES.
SKIN:
TEMPORARY IRRITATION (ITCHING) OR REDNESS MAY OCCUR.
INGESTION:
THIS PRODUCT IS NOT INTENDED TO BE INGESTED (EATEN). IF INGESTED, IT MAY
CAUSE TEMPORARY IRRITATION TO THE GASTROINTESTINAL (DIGESTIVE) TRACT.
EYES: TEMPORARY IRRITATION (ITCHING) OR REDNESS MAY OCCUR.
EARS: TEMPORARY IRRITATION (ITCHING) OR REDNESS MAY OCCUR.
PRIMARY ROUTES OF ENTRY (EXPOSURE):
INHALATION (BREATHING DUST, FIBERS, OR VAPORS), SKIN, AND EYE CONTACT.
TARGET ORGANS:
NOSE (NASAL PASSAGES), THROAT, LUNGS, SKIN, EYES.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE:
PRE-EXISTING CHRONIC RESPIRATORY, SKIN, OR EYE DISEASES OR CONDITIONS.
| SECTION 4 - FIRST AID MEASURES | |
FIRST AID:
INHALATION:
REMOVE TO FRESH AIR. DRINK WATER TO CLEAR THROAT, AND BLOW NOSE TO REMOVE
DUST.
FIRST AID:
SKIN:
WASH GENTLY WITH SOAP AND WARM WATER TO REMOVE DUST. WASH HANDS BEFORE
EATING OR USING THE RESTROOM.
FIRST AID:
INGESTION:
PRODUCT IS NOT INTENDED TO BE INGESTED OR EATEN. IF THIS PRODUCT IS
INGESTED, IRRITATION OF THE GASTROINTESTINAL (GI) TRACT MAY OCCUR, AND
SHOULD BE TREATED SYMPTOMATICALLY. RINSE MOUTH WITH WATER TO REMOVE FIBERS,
AND DRINK PLENTY OF WATER TO HELP REDUCE THE IRRITATION. NO CHRONIC EFFECTS
ARE EXPECTED FOLLOWING INGESTION.
FIRST AID:
EYES:
DO NOT RUB OR SCRATCH YOUR EYES. DUST PARTICLES MAY CAUSE THE EYE TO BE
SCRATCHED. FLUSH EYES WITH LARGE AMOUNTS OF WATER FOR 5-15 MINUTES. IF
IRRITATION PERSISTS, CONTACT A MEDICAL PROFESSIONAL.
FIRST AID:
EARS:
WASH EXPOSED SKIN WITH SOAP AND WATER. IF IRRITATION DEVELOPS IN THE INNER
EAR, SEEK MEDICAL ATTENTION.
FIRST AID:
NOTES TO PHYSICIAN:
IRRITATING GASES MAY BE RELEASED UNDER CONDITIONS OF HIGH HEAT OR HUMIDITY.
AT HIGH LEVELS, THESE COULD CAUSE SEVERE UPPER RESPIRATORY AND EYE
IRRITATION. FORMALDEHYDE GAS IS A SKIN AND RESPIRATORY SENSITIZER.
TREATMENT SHOULD BE DIRECTED TOWARD REMOVING THE SOURCE OF IRRITATION
WITH SYMPTOMATIC TREATMENT AS NECESSARY.
| SECTION 5 - FIRE FIGHTING MEASURES | |
FLASH POINT: NOT APPLICABLE
METHOD USED: NOT APPLICABLE
UPPER FLAMMABLE LIMIT (UFL): NOT APPLICABLE
LOWER FLAMMABLE LIMIT (LFL): NOT APPLICABLE
AUTO IGNITION: NOT DETERMINED
FLAMMABILITY CLASSIFICATION: NOT DETERMINED
RATE OF BURNING: NOT DETERMINED
GENERAL FIRE HAZARDS:
THERE IS NO POTENTIAL FOR SPONTANEOUS FIRE OR EXPLOSION.
EXTINGUISHING MEDIA: CARBON DIOXIDE (CO2), WATER, WATER FOG, DRY CHEMICAL.
FIRE FIGHTING EQUIPMENT/INSTRUCTIONS:
NO SPECIAL PROCEDURES ARE EXPECTED TO BE NECESSARY FOR THIS PRODUCT.
NORMAL FIRE FIGHTING PROCEDURES SHOULD BE FOLLOWED TO AVOID INHALATION
OF SMOKE AND GASES.
| SECTION 6 - ACCIDENTAL RELEASE MEASURES | |
CLEAN-UP PROCEDURES:
PICK UP LARGE PIECES. VACUUM DUSTS. IF SWEEPING IS NECESSARY, USE A DUST
SUPPRESSANT SUCH AS WATER. DO NOT DRY SWEEP DUST ACCUMULATION. THESE
PROCEDURES WILL HELP TO MINIMIZE POTENTIAL EXPOSURES.
| SECTION 7 - HANDLING AND STORAGE | |
HANDLING PROCEDURES:
USE PROTECTIVE EQUIPMENT AS DESCRIBED IN SECTION 8 OF THIS SAFETY DATA
SHEET WHEN HANDLING UNCONTAINED MATERIAL. HANDLE IN ACCORDANCE WITH GOOD
INDUSTRIAL HYGIENE AND SAFETY PRACTICES.
STORAGE PROCEDURES:
WAREHOUSE STORAGE SHOULD BE IN ACCORDANCE WITH PACKAGE DIRECTIONS, IF ANY.
MATERIAL SHOULD BE KEPT CLEAN, DRY, AND IN ORIGINAL PACKAGING.
| SECTION 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION | |
THE OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) HAS NOT ADOPTED
SPECIFIC OCCUPATIONAL EXPOSURE STANDARDS FOR FIBER GLASS. FIBER GLASS IS
TREATED AS A NUISANCE DUST AND IS REGULATED BY OSHA AS A PARTICULATE NOT
OTHERWISE REGULATED (TOTAL DUST) SHOWN IN CFR 1910.1000 TABLE Z-3.
RESPIRABLE FRACTION: 5 MG/M3
TOTAL DUST: 15 MG/M3
FORMALDEHYDE (50-00-0):
ACGIH: 0.3 PPM CEILING
OSHA:
0.5 PPM ACTION LEVEL; 0.75 PPM TWA; 2 PPM STEL (IRRITANT AND POTENTIAL
CANCER HAZARD - SEE 29 CFR 1910.1048)
CARBON BLACK (PRESENT IN BLACK PRODUCTS ONLY) (1333-86-4):
ACGIH: 3.5 MG/M3 TWA
OSHA: 3.5 MG/M3 TWA
PERSONAL PROTECTIVE EQUIPMENT:
PERSONAL PROTECTIVE EQUIPMENT:
EYES/FACE:
SAFETY GOGGLES ARE RECOMMENDED TO KEEP DUST, FIBERS, GASES, AND VAPORS OUT
OF THE EYES.
PERSONAL PROTECTIVE EQUIPMENT:
EARS:
USE EAR PROTECTION (EARPLUGS, HOOD, OR EARMUFFS) TO PREVENT AIRBORNE DUST
OR FIBERS FROM ENTERING THE EAR, IF NECESSARY.
PERSONAL PROTECTIVE EQUIPMENT:
SKIN:
LEATHER OR COTTON GLOVES SHOULD BE WORN TO PREVENT SKIN CONTACT AND
IRRITATION. BARRIER CREAMS MAY ALSO BE USED TO REDUCE SKIN CONTACT AND
IRRITATION CAUSED BY FIBER GLASS.
PERSONAL PROTECTIVE EQUIPMENT:
RESPIRATORY:
A RESPIRATOR SHOULD BE USED IF VENTILATION IS UNAVAILABLE, OR IS INADEQUATE
FOR KEEPING DUST AND FIBER LEVELS BELOW THE APPLICABLE EXPOSURE LIMITS.
IN THOSE CASES, USE A NIOSH-CERTIFIED DISPOSABLE OR REUSABLE PARTICULATE
RESPIRATOR WITH AN EFFICIENCY RATING OF N95 OR HIGHER (UNDER 42 CFR 84)
WHEN WORKING WITH THIS PRODUCT. FOR EXPOSURES UP TO FIVE TIMES THE
ESTABLISHED EXPOSURE LIMITS USE A QUARTER-MASK RESPIRATOR, RATED N95 OR
HIGHER; AND FOR EXPOSURES UP TO TEN TIMES THE ESTABLISHED EXPOSURE LIMITS
USE A HALF-MASK RESPIRATOR (E.G., MSA'S DM-11, RACAL'S DELTA N95, 3M'S
8210), RATED N95 OR HIGHER. OPERATIONS SUCH AS SAWING, BLOWING, TEAR OUT,
AND SPRAYING MAY GENERATE AIRBORNE FIBER CONCENTRATIONS REQUIRING A HIGHER
LEVEL OF RESPIRATORY PROTECTION. FOR EXPOSURES UP TO 50 TIMES THE
ESTABLISHED EXPOSURE LIMITS USE A FULL-FACE RESPIRATOR, RATED N99 OR
HIGHER.
VENTILATION:
IN FIXED MANUFACTURING SETTINGS, LOCAL EXHAUST VENTILATION SHOULD BE
PROVIDED AT AREAS OF CUTTING TO REMOVE AIRBORNE DUST AND FIBERS. GENERAL
DILUTION VENTILATION SHOULD BE PROVIDED AS NECESSARY TO KEEP AIRBORNE DUST
AND FIBERS BELOW THE APPLICABLE EXPOSURE LIMITS AND GUIDELINES. THE NEED
FOR VENTILATION SYSTEMS SHOULD BE EVALUATED BY A PROFESSIONAL INDUSTRIAL
HYGIENIST, WHILE THE DESIGN OF SPECIFIC VENTILATION SYSTEMS SHOULD BE
CONDUCTED BY A PROFESSIONAL ENGINEER.
PERSONAL PROTECTIVE EQUIPMENT:
GENERAL:
WEAR A CAP, A LOOSE-FITTING, LONG-SLEEVED SHIRT AND LONG PANTS TO PROTECT
SKIN FROM IRRITATION. EXPOSED SKIN AREAS SHOULD BE WASHED WITH SOAP AND
WARM WATER AFTER HANDLING OR WORKING WITH FIBER GLASS. CLOTHING SHOULD BE
WASHED SEPARATELY FROM OTHER CLOTHES, AND THE WASHER SHOULD BE RINSED
THOROUGHLY (RUN EMPTY FOR A COMPLETE WASH CYCLE). THIS WILL REDUCE THE
CHANCES OF FIBER GLASS BEING TRANSFERRED TO OTHER CLOTHING.
| SECTION 9 - PHYSICAL & CHEMICAL PROPERTIES | |
APPEARANCE:
GOLD, YELLOW, OR BLACK FIBROUS GLASS BLANKET, BOARD, OR FORMED SHAPES, WITH
OR WITHOUT FACINGS.
ODOR: MILD FORMALDEHYDE
PHYSICAL STATE: SOLID
pH: NOT APPLICABLE
VAPOR PRESSURE: NOT APPLICABLE
VAPOR DENSITY: NOT APPLICABLE
BOILING POINT: NOT APPLICABLE
MELTING POINT: >704 DEG. C / 1300 DEG. F
SOLUBILITY (H2O): NIL
SPECIFIC GRAVITY: VARIABLE
VOC: NOT DETERMINED
| SECTION 10 - STABILITY & REACTIVITY INFORMATION | |
STABILITY: THIS IS A STABLE MATERIAL.
HAZARDOUS DECOMPOSITION:
THE DECOMPOSITION PRODUCTS FROM THIS MATERIAL ARE THOSE THAT WOULD BE
EXPECTED FROM ANY ORGANIC (CARBON-CONTAINING) MATERIAL, AND ARE MAINLY
DERIVED FROM PYROLYSIS, OR BURNING, OF THE RESIN. THESE DECOMPOSITION
PRODUCTS MAY INCLUDE CARBON MONOXIDE, CARBON DIOXIDE, AND CARBON PARTICLES.
FORMALDEHYDE GAS MAY ALSO BE RELEASED DURING DECOMPOSITION.
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR.
| SECTION 11 - TOXICOLOGICAL INFORMATION | |
ACUTE TOXICITY:
A:
GENERAL PRODUCT INFORMATION:
DUST FROM THIS PRODUCT IS A MECHANICAL IRRITANT, WHICH MEANS THAT IT MAY
CAUSE TEMPORARY IRRITATION OR SCRATCHINESS OF THE THROAT, AND/OR ITCHING OF
THE EYES AND SKIN.
GASES RELEASED UNDER CONDITIONS OF HIGH HEAT AND HUMIDITY CAN CAUSE SEVERE
EYE AND RESPIRATORY IRRITATION.
B:
COMPONENT ANALYSIS - LD50/LC50:
FORMALDEHYDE (50-00-0):
INHALATION LC50 RAT: 0.578 MG/1/4H
INHALATION LC50 RAT: 250 PPM/4H
ORAL LD50 RAT: 100 MG/KG
DERMAL LD50 RABBIT: 270 MG/KG
CARBON BLACK (PRESENT IN BLACK PRODUCTS ONLY) (1333-86-4):
ORAL LD50 RAT: >15400 MG/KG
DERMAL LD50 RABBIT: >3 G/KG
CYCLODODECANE, HEXABROMO-(PRESENT IN SPIRACOUSTIC ONLY) (25637-99-4):
INHALATION LC50 RAT: >200 MG/L/1H
ORAL LD50 RAT: >10000 MG/KG
DERMAL LD50 RABBIT: >8000 MG/KG
ANTIMONY TRIOXIDE (1309-64-4):
ORAL LD50 RAT: >34600 MG/KG
CARCINOGENICITY:
FIBER GLASS WOOL:
ACGIH: A4 - NOT CLASSIFIABLE AS A HUMAN CARCINOGEN
IARC:
GROUP 3 - NOT CLASSIFIABLE (IARC MONOGRAPH 81 (2002) (LISTED UNDER MAN-MADE
MINERAL FIBRES), MONOGRAPH 43 (1988))
FORMALDEHYDE (50-00-0):
ACGIH: A2 - SUSPECTED HUMAN CARCINOGEN
OSHA:
0.5 PPM ACTION LEVEL; 0.75 PPM TWA; 2 PPM STEL (IRRITANT AND POTENTIAL
CANCER HAZARD - SEE 29 CFR 1910.1048)
NTP: REASONABLY ANTICIPATED TO BE A CARCINOGEN (POSSIBLE SELECT CARCINOGEN)
IARC:
GROUP 1 - KNOWN HUMAN CARCINOGEN (IARC MONOGRAPH 88 (2006), MONOGRAPH 62
(1995), SUPPLEMENT 7 (1987))
CARBON BLACK (PRESENT IN BLACK PRODUCTS ONLY) (1333-86-4):
ACGIH: A4 - NOT CLASSIFIABLE AS A HUMAN CARCINOGEN
IARC:
GROUP 2B - POSSIBLY CARCINOGENIC TO HUMANS (IARC MONOGRAPH 93 POSTED,
MONOGRAPH 65 (1996))
ANTIMONY TRIOXIDE (1309-64-4):
ACGIH: A2 - SUSPECTED HUMAN CARCINOGEN (PRODUCTION)
IARC:
GROUP 2B - POSSIBLY CARCINOGENIC TO HUMANS (IARC MONOGRAPH 47 (1989))
CHRONIC TOXICITY:
EXPOSURE TO FORMALDEHYDE GAS (IN HIGH TEMPERATURE APPLICATIONS, TREATMENT,
CURING, OR IN GEOGRAPHIC AREAS OF HIGH HEAT AND HUMIDITY) MAY CAUSE EYE
AND UPPER RESPIRATORY IRRITATION, AND POSSIBLE RESPIRATORY OR SKIN
SENSITIZATION (ALLERGY). IF SENSITIZATION OCCURS, SUBSEQUENT EXPOSURES
TO FORMALDEHYDE MAY WORSEN ASTHMA OR OTHER RESPIRATORY PROBLEMS, AND
CAUSE ALLERGIC-TYPE REACTIONS.
EXPOSURE TO FORMALDEHYDE GAS HAS BEEN ASSOCIATED WITH THE DEVELOPMENT OF
NASOPHARYNGEAL CANCER IN LABORATORY ANIMALS AND HUMANS. FORMALDEHYDE HAS
BEEN CLASSIFIED AS A KNOWN HUMAN CARCINOGEN, GROUP 1, BY THE INTERNATIONAL
AGENCY FOR RESEARCH ON CANCER (IARC). THE US OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION (OSHA) AND THE US NATIONAL TOXICOLOGY PROGRAM (NTP) CONSIDER
FORMALDEHYDE TO HAVE CARCINOGENIC POTENTIAL. OSHA SPECIFICALLY REGULATES
FORMALDEHYDE UNDER 29 CFR 1910.1048.
FIBER GLASS WOOL:
IN OCTOBER 2001, IARC CLASSIFIED FIBER GLASS WOOL AS GROUP 3, "NOT
CLASSIFIABLE AS TO ITS CARCINOGENICITY TO HUMANS." THE 2001 DECISION WAS
BASED ON CURRENT HUMAN AND ANIMAL RESEARCH THAT SHOWS NO ASSOCIATION
BETWEEN INHALATION EXPOSURE TO DUST FROM FIBER GLASS WOOL AND THE
DEVELOPMENT OF RESPIRATORY DISEASE. THIS IS A REVERSAL OF THE IARC FINDING
IN 1987 OF A GROUP 2B DESIGNATION (POSSIBLY CARCINOGENIC TO HUMANS) BASED
ON EARLIER STUDIES IN WHICH ANIMALS WERE INJECTED WITH LARGE QUANTITIES OF
FIBER GLASS. NTP AND ACGIH HAVE NOT YET REVIEWED THE IARC RECLASSIFICATION
OR THE MOST CURRENT FIBER GLASS HEALTH RESEARCH; AT THIS TIME, BOTH
AGENCIES CONTINUE TO CLASSIFY GLASS WOOL BASED ON THE EARLIER ANIMAL
INJECTION STUDIES.
| SECTION 12 - ECOLOGICAL INFORMATION | |
ECOTOXICITY:
A:
GENERAL PRODUCT INFORMATION: NO DATA AVAILABLE FOR THIS PRODUCT.
B:
COMPONENT ANALYSIS - ECOTOXICITY - AQUATIC TOXICITY:
FORMALDEHYDE (50-00-0):
96 HR LC50 PIMEPHALES PROMELAS: 24.1 MG/L (FLOW-THROUGH)
96 HR LC50 LEPOMIS MACROCHIRUS: 0.10 MG/L (FLOW-THROUGH)
96 HR LC50 BRACHYDANIO RERIO: 41 MG/L (STATIC)
5 MIN EC50 PHOTOBACTERIUM PHOSPHOREUM: 9.0 MG/L
15 MIN EC50 PHOTOBACTERIUM PHOSPHOREUM: 7.26 MG/L
25 MIN EC50 PHOTOBACTERIUM PHOSPHOREUM: 6.81 MG/L
30 MIN EC50 PHOTOBACTERIUM PHOSPHOREUM: 16.5 MG/L
1 HR EC50 VIBRIO HARVEYI: 1.2 MG/L
5 HR EC50 VIBRIO HARVEYI: 3.7 MG/L
72 HR EC50 COLPODA ASPERA: 5.39 MG/L
96 HR EC50 WATER FLEA: 20 MG/L
48 HR EC50 DAPHNIA MAGNA: 2 MG/L
CARBON BLACK (PRESENT IN BLACK PRODUCTS ONLY) (1333-86-4):
24 HR EC50 DAPHNIA MAGNA: >5600 MG/L
CYCLODODECANE, HEXABROMO-(PRESENT IN SPIRACOUSTIC ONLY) (25637-99-4):
96 HR LC50 LEPOMIS MACROCHIRUS: >100 MG/L (SEMI-STATIC)
72 HR EC50 SKELETONEMA COSTATUM: 0.0093-0.37 MG/L
ANTIMONY TRIOXIDE (1309-64-4):
96 HR LC50 PIMEPHALES PROMELAS: 833.0 MG/L
96 HR LC50 LEPOMIS MACROCHIRUS: 530 MG/L
96 HR LC50 BRACHYDANIO RERIO: >1000 MG/L (STATIC)
72 HR EC50 SELENASTRUM CAPRICORNUTUM: 67 MG/L
7 HR EC50 PSEUDOMONAS PUTIDA: >3.5 MG/L
48 HR EC50 DAPHNIA MAGNA: >1000 MG/L
| SECTION 13 - DISPOSAL CONSIDERATIONS | |
US EPA WASTE NUMBER & DESCRIPTIONS:
GENERAL PRODUCT INFORMATION:
THIS PRODUCT IS NOT REGULATED AS A HAZARDOUS WASTE BY THE U.S.
ENVIRONMENTAL PROTECTION AGENCY (EPA) UNDER RESOURCE CONSERVATION AND
RECOVERY ACT (RCRA) REGULATIONS.
DISPOSAL INSTRUCTIONS:
DISPOSE OF WASTE MATERIAL ACCORDING TO LOCAL, STATE, FEDERAL, AND
PROVINCIAL ENVIRONMENTAL REGULATIONS.
| SECTION 14 - TRANSPORTATION INFORMATION | |
INTERNATIONAL TRANSPORTATION REGULATIONS:
THIS PRODUCT IS NOT CLASSIFIED AS A HAZARDOUS MATERIAL FOR TRANSPORT.
MINERAL WOOL BATTS BATTING OR BLANKETS, PLAIN OR SATURATED 2299918001
| SECTION 15 - REGULATORY INFORMATION | |
US FEDERAL REGULATIONS:
A:
GENERAL PRODUCT INFORMATION:
SARA 311/312:
THIS PRODUCT IS NOT CLASSIFIED AS HAZARDOUS UNDER SARA 311/312.
B:
COMPONENT ANALYSIS:
THIS MATERIAL CONTAINS ONE OR MORE OF THE FOLLOWING CHEMICALS REQUIRED TO
BE IDENTIFIED UNDER SARA SECTION 302 (40 CFR 355 APPENDIX A), SARA SECTION
313 (40 CFR 372.65) AND/OR CERCLA (40 CFR 302.4).
FORMALDEHYDE (50-00-0):
SARA 302: 500 LB TPQ
SARA 313: 0.1 % DE MINIMIS CONCENTRATION
CERCLA:
100 LB FINAL RQ
45.4 KG FINAL RQ
ANTIMONY TRIOXIDE (1309-64-4):
CERCLA:
1000 LB FINAL RQ
454 KG FINAL RQ
STATE REGULATIONS:
A:
GENERAL PRODUCT INFORMATION:
OTHER STATE REGULATIONS MAY APPLY. CHECK INDIVIDUAL STATE REQUIREMENTS.
B:
COMPONENT ANALYSIS - STATE:
THE FOLLOWING COMPONENTS APPEAR ON ONE OR MORE OF THE FOLLOWING STATE
HAZARDOUS SUBSTANCES LISTS:
COMPONENT CAS # CA FL MA MN NJ PA
FIBER GLASS WOOL NOT YES(1) NO YES(1) YES YES(2) YES(1)
((1)RELATED TO APPLICABLE
MINERAL WOOL FIBER)
((2)RELATED TO
FIBROUS GLASS)
FORMALDEHYDE 50-00-0 YES NO YES YES YES YES
CARBON BLACK 1333-86-4 YES NO YES YES YES YES
(PRESENT IN BLACK
PRODUCTS ONLY)
ANTIMONY TRIOXIDE 1309-64-4 YES NO YES YES YES YES
THE FOLLOWING STATEMENT(S) ARE PROVIDED UNDER THE CALIFORNIA SAFE DRINKING
WATER AND TOXIC ENFORCEMENT ACT OF 1986 (PROPOSITION 65):
WARNING!
THIS PRODUCT CONTAINS A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE
CANCER.
COMPONENT CAS #
FIBER GLASS WOOL ((1) RELATED TO MINERAL WOOL FIBER) NOT APPLICABLE
((2) RELATED TO FIBROUS GLASS)
FORMALDEHYDE 50-00-0
CARBON BLACK (PRESENT IN BLACK PRODUCTS ONLY) 1333-86-4
ANTIMONY TRIOXIDE 1309-64-4
A:
TSCA STATUS:
THIS PRODUCT AND ITS COMPONENTS ARE LISTED ON THE TSCA 8(B) INVENTORY.
NONE OF THE COMPONENTS LISTED IN THIS PRODUCT ARE LISTED ON THE TSCA EXPORT
NOTIFICATION 12(B) LIST.
INTERNATIONAL REGULATIONS:
A:
GENERAL PRODUCT INFORMATION:
THESE PRODUCTS ARE CONSIDERED ARTICLES UNDER BOTH U.S. AND INTERNATIONAL
PRODUCT REGULATIONS AND AS SUCH, THEY DO NOT REQUIRE REGISTRATION OR
NOTIFICATION ON THE VARIOUS COUNTRY-SPECIFIC INVENTORIES.
B:
COMPONENT ANALYSIS - WHMIS IDL:
THE FOLLOWING COMPONENTS ARE IDENTIFIED UNDER THE CANADIAN HAZARDOUS
PRODUCTS ACT INGREDIENT DISCLOSURE LIST:
COMPONENT CAS # MINIMUM CONCENTRATION
FIBER GLASS WOOL NOT APPLICABLE 1 % (RELATED TO FIBROUS GLASS)
FORMALDEHYDE 50-00-0 0.1 %
WHMIS CLASSIFICATION:
CONTROLLED PRODUCT CLASSIFICATION: D2A, BASED ON THE IARC CLASSIFICATIONS
FOR ANTIMONY TRIOXIDE (GROUP 2B) AND FORMALDEHYDE (GROUP 1).
| SECTION 16 - OTHER INFORMATION | |
OTHER INFORMATION:
PREPARED FOR:
JOHNS MANVILLE
PERFORMANCE MATERIALS
P. O. BOX 5108
DENVER, CO 80217-5108
USA
PREPARED BY:
JOHNS MANVILLE TECHNICAL CENTER
P.O. BOX 625005
LITTLETON, CO 80162-5005
USA
THE INFORMATION HEREIN IS PRESENTED IN GOOD FAITH AND BELIEVED TO BE
ACCURATE AS OF THE EFFECTIVE DATE GIVEN. HOWEVER, NO WARRANTY, EXPRESSED
OR IMPLIED, IS GIVEN. IT IS THE BUYER'S RESPONSIBILITY TO ENSURE THAT ITS
ACTIVITIES COMPLY WITH FEDERAL, STATE OR PROVINCIAL, AND LOCAL LAWS.
DATE MSDS # REASON
04/28/04 1009-2.0106 REGULATORY UPDATE. MINOR EDITS.
05/20/04 1009-2.0107 SECT. 1 REMOVAL OF DISCONTINUED TRADE NAMES:
824 CAN SPIN-GLAS(R*); 830 CAN SPIN-GLAS(R*);
ACOUSTIC BACKING BOARD; BS 476, ECOTHERM(TM)
INDUSTRIAL PIPE INSULATION; FABRICATED DUCT BOARD;
PERMACOTE SPIRACOUSTIC(TM); PIPE AND TANK
INSULATION; RIGID ROUND(TM) (FACED);
SPIRACOUSTIC(TM); SUPERROUND(R*).
08/05/04 1009-2.0108 SECT. 1 LABEL ID EDIT. REMOVAL OF DISCONTINUED
TRADE NAME, MICRO-FLEX CTS.
03/22/05 1009-2.0108 SECT. 1 ADDITION OF INSUL-SHIELD(R*) COATED BLACK
FROM MSDS 1010. ADDITION OF BLENDED BLOWING WOOL.
EDITS TO SECT. 2 FOR NEW ADDITIONS.
10/03/05 1009-2.0110 SECTION 1, SUPERVANE WAS REMOVED. DISCONTINUED
PRODUCT.
11/17/05 1009-2.0111 REGULATORY UPDATE. MINOR EDITS IN SECTIONS 8, 11,
AND 15.
REMOVED ALL REVISION NOTES PRIOR TO 2004.
REVISION NOTES ARE STORED IN DATABASE ARCHIVES.
01/31/07 1009-2.0112 ADDITION OF MICRO-LOK HP TO TRADE NAMES. UPDATES
MADE THROUGHOUT SDS FOR CURRENT TRADE NAMES LISTED
ON THIS SDS. SECTION 15 TSCA 12B EDITS. REMOVED
DBDO. THESE PRODUCTS ARE ARTICLES UNDER TSCA AND
DBDO DOES NOT NEED TO BE REPORTED UNDER TSCA 12B.
06/26/07 1009-2.0113 ADDITION OF MICROMAT RX TO TRADE NAMES. MINOR
EDITS THROUGHOUT. ADDITION OF WHMIS CLASSIFICATION
IN SECTION 15.
ISSUE DATE: 06/26/2007
REVISION: 2.0113