| Common Name: | 5-WAY SPRAY |
| Manufacturer: | 3M |
| SDS Revision Date: | 2/3/2005 |
| SDS Format: | No Format Specified |
| Item Number(s): | 2GKH1 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M
MATERIAL SAFETY DATA SHEET
3M(TM) 5-WAY SPRAY
02/03/2005
3M
MATERIAL SAFETY DATA SHEET
COPYRIGHT, 2005, 3M COMPANY. ALL RIGHTS RESERVED. COPYING AND/OR
DOWNLOADING OF THIS INFORMATION FOR THE PURPOSE OF PROPERLY UTILIZING 3M
PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND (2) NEITHER THE COPY NOR THE ORIGINAL IS
RESOLD OR OTHERWISE DISTRIBUTED WITH THE INTENTION OF EARNING A PROFIT
THEREON.
| SECTION 1: PRODUCT AND COMPANY IDENTIFICATION |  |
PRODUCT NAME: 3M(TM) 5-WAY SPRAY
MANUFACTURER: 3M
DIVISION: INDUSTRIAL ADHESIVES AND TAPES
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 OR (651) 737-6501 (24 HOURS)
ISSUE DATE: 02/03/2005
SUPERCEDES DATE: 11/30/2004
DOCUMENT GROUP: 18-3229-4
PRODUCT USE:
SPECIFIC USE: PENETRANT, LUBRICANT AND DEMOISTURIZER
| SECTION 2: INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
ALIPHATIC HYDROCARBON 64742-47-8 50 - 60
PROPANE 74-98-6 10 - 20
BUTANE 106-97-8 10 - 20
PETROLEUM OIL 64742-52-5 3 - 7
PETROLATUM 8009-03-8 1 - 5
HEAVY PARAFFINIC OIL 64742-54-7 1 - 5
| SECTION 3: HAZARDS IDENTIFICATION | |
3.1 EMERGENCY OVERVIEW
ODOR, COLOR, GRADE: AMBER COLORED LIQUID, STRONG SOLVENT ODOR
GENERAL PHYSICAL FORM: GAS
IMMEDIATE HEALTH, PHYSICAL, AND ENVIRONMENTAL HAZARDS:
CLOSED CONTAINERS EXPOSED TO HEAT FROM FIRE MAY BUILD PRESSURE AND EXPLODE.
EXTREMELY FLAMMABLE LIQUID AND VAPOR. VAPORS MAY TRAVEL LONG DISTANCES
ALONG THE GROUND OR FLOOR TO AN IGNITION SOURCE AND FLASH BACK. AEROSOL
CONTAINER CONTAINS FLAMMABLE MATERIAL UNDER PRESSURE. MAY CAUSE TARGET
ORGAN EFFECTS.
3.2 POTENTIAL HEALTH EFFECTS:
EYE CONTACT:
MODERATE EYE IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND BLURRED OR
HAZY VISION.
SKIN CONTACT:
MODERATE SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE LOCALIZED REDNESS, SWELLING, ITCHING, AND
DRYNESS.
INHALATION:
UPPER RESPIRATORY TRACT IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL DISCHARGE, HEADACHE,
HOARSENESS, AND NOSE AND THROAT PAIN.
MAY BE ABSORBED FOLLOWING INHALATION AND CAUSE TARGET ORGAN EFFECTS.
INTENTIONAL CONCENTRATION AND INHALATION MAY BE HARMFUL OR FATAL.
INGESTION:
GASTROINTESTINAL IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABDOMINAL PAIN, NAUSEA, DIARRHEA AND VOMITING.
MAY BE ABSORBED FOLLOWING INGESTION AND CAUSE TARGET ORGAN EFFECTS.
TARGET ORGAN EFFECTS:
CENTRAL NERVOUS SYSTEM (CNS) DEPRESSION:
SIGNS/SYMPTOMS MAY INCLUDE HEADACHE, DIZZINESS, DROWSINESS, INCOORDINATION,
NAUSEA, SLOWED REACTION TIME, SLURRED SPEECH, GIDDINESS, AND
UNCONSCIOUSNESS.
| SECTION 4: FIRST AID MEASURES | |
4.1 FIRST AID PROCEDURES:
THE FOLLOWING FIRST AID RECOMMENDATIONS ARE BASED ON AN ASSUMPTION THAT
APPROPRIATE PERSONAL AND INDUSTRIAL HYGIENE PRACTICES ARE FOLLOWED.
EYE CONTACT:
FLUSH EYES WITH LARGE AMOUNTS OF WATER. IF SIGNS/SYMPTOMS PERSIST, GET
MEDICAL ATTENTION.
SKIN CONTACT:
REMOVE CONTAMINATED CLOTHING AND SHOES. IMMEDIATELY FLUSH SKIN WITH LARGE
AMOUNTS OF WATER. GET MEDICAL ATTENTION. WASH CONTAMINATED CLOTHING AND
CLEAN SHOES BEFORE REUSE.
INHALATION:
REMOVE PERSON TO FRESH AIR. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL
ATTENTION.
IF SWALLOWED:
DO NOT INDUCE VOMITING. GIVE VICTIM TWO GLASSES OF WATER. NEVER GIVE
ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON. GET IMMEDIATE MEDICAL
ATTENTION.
| SECTION 5: FIRE FIGHTING MEASURES | |
5.1 FLAMMABLE PROPERTIES:
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
FLASH POINT: 00 DEG. F
FLAMMABLE LIMITS - LEL: 0.6
FLAMMABLE LIMITS - UEL: 9.5
5.2 EXTINGUISHING MEDIA:
USE FIRE EXTINGUISHERS WITH CLASS B EXTINGUISHING AGENTS
(E.G., DRY CHEMICAL, CARBON DIOXIDE).
5.3 PROTECTION OF FIRE FIGHTERS:
SPECIAL FIRE FIGHTING PROCEDURES:
WEAR FULL PROTECTIVE EQUIPMENT (BUNKER GEAR) AND A SELF-CONTAINED BREATHING
APPARATUS (SCBA).
UNUSUAL FIRE AND EXPLOSION HAZARDS:
CLOSED CONTAINERS EXPOSED TO HEAT FROM FIRE MAY BUILD PRESSURE AND EXPLODE.
EXTREMELY FLAMMABLE LIQUID AND VAPOR. VAPORS MAY TRAVEL LONG DISTANCES
ALONG THE GROUND OR FLOOR TO AN IGNITION SOURCE AND FLASH BACK. AEROSOL
CONTAINER CONTAINS FLAMMABLE MATERIAL UNDER PRESSURE.
NOTE:
SEE STABILITY AND REACTIVITY (SECTION 10) FOR HAZARDOUS COMBUSTION AND
THERMAL DECOMPOSITION INFORMATION.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
ACCIDENTAL RELEASE MEASURES:
REFER TO OTHER SECTIONS OF THIS MSDS FOR INFORMATION REGARDING PHYSICAL AND
HEALTH HAZARDS, RESPIRATORY PROTECTION, VENTILATION, AND PERSONAL
PROTECTIVE EQUIPMENT. CALL 3M-HELPS LINE (1-800-364-3577) FOR MORE
INFORMATION ON HANDLING AND MANAGING THE SPILL. EVACUATE UNPROTECTED AND
UNTRAINED PERSONNEL FROM HAZARD AREA. THE SPILL SHOULD BE CLEANED UP BY
QUALIFIED PERSONNEL. REMOVE ALL IGNITION SOURCES SUCH AS FLAMES, SMOKING
MATERIALS, AND ELECTRICAL SPARK SOURCES. USE ONLY NON-SPARKING TOOLS.
VENTILATE THE AREA WITH FRESH AIR. IF POSSIBLE, SEAL LEAKING CONTAINER.
PLACE LEAKING CONTAINERS IN A WELL-VENTILATED AREA, PREFERABLY AN
OPERATING EXHAUST HOOD, OR IF NECESSARY OUTDOORS ON AN IMPERMEABLE SURFACE
UNTIL APPROPRIATE PACKAGING FOR THE LEAKING CONTAINER OR ITS CONTENTS IS
AVAILABLE. COVER SPILL AREA WITH A FIRE-EXTINGUISHING FOAM. AN AQUEOUS FILM
FORMING FOAM (AFFF) IS RECOMMENDED. WORKING FROM AROUND THE EDGES OF THE
SPILL INWARD, COVER WITH BENTONITE, VERMICULITE, OR COMMERCIALLY AVAILABLE
INORGANIC ABSORBENT MATERIAL. MIX IN SUFFICIENT ABSORBENT UNTIL IT APPEARS
DRY.
REMEMBER, ADDING AN ABSORBENT MATERIAL DOES NOT REMOVE A TOXIC, CORROSIVITY
OR FLAMMABILITY HAZARD. COLLECT AS MUCH OF THE SPILLED MATERIAL AS POSSIBLE
USING NON-SPARKING TOOLS.
CLEAN UP RESIDUE WITH AN APPROPRIATE ORGANIC SOLVENT. READ AND FOLLOW
SAFETY PRECAUTIONS ON THE SOLVENT LABEL AND MSDS. PLACE IN A METAL
CONTAINER APPROVED FOR TRANSPORTATION BY APPROPRIATE AUTHORITIES. SEAL THE
CONTAINER. DISPOSE OF COLLECTED MATERIAL AS SOON AS POSSIBLE.
IN THE EVENT OF A RELEASE OF THIS MATERIAL, THE USER SHOULD DETERMINE IF
THE RELEASE QUALIFIES AS REPORTABLE ACCORDING TO LOCAL, STATE, AND FEDERAL
REGULATIONS.
| SECTION 7: HANDLING AND STORAGE | |
7.1 HANDLING:
DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT. WASH EXPOSED AREAS
THOROUGHLY WITH SOAP AND WATER. KEEP AWAY FROM HEAT, SPARKS, OPEN FLAME,
PILOT LIGHTS AND OTHER SOURCES OF IGNITION. NO SMOKING WHILE HANDLING THIS
MATERIAL. AVOID EYE CONTACT WITH VAPORS, MISTS, OR SPRAY.
7.2 STORAGE: STORE AWAY FROM ACIDS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1 ENGINEERING CONTROLS:
USE WITH APPROPRIATE LOCAL EXHAUST VENTILATION. DO NOT USE IN A CONFINED
AREA OR AREAS WITH LITTLE OR NO AIR MOVEMENT. USE GENERAL DILUTION
VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO CONTROL AIRBORNE EXPOSURES
TO BELOW OCCUPATIONAL EXPOSURE LIMITS AND/OR CONTROL MIST, VAPOR, OR SPRAY.
IF VENTILATION IS NOT ADEQUATE, USE RESPIRATORY PROTECTION EQUIPMENT.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE):
8.2.1 EYE/FACE PROTECTION:
AVOID EYE CONTACT. AVOID EYE CONTACT WITH VAPORS, MISTS, OR SPRAY.
8.2.2 SKIN PROTECTION:
AVOID SKIN CONTACT. AVOID PROLONGED OR REPEATED SKIN CONTACT. SELECT AND
USE GLOVES AND/OR PROTECTIVE CLOTHING TO PREVENT SKIN CONTACT BASED ON THE
RESULTS OF AN EXPOSURE ASSESSMENT. CONSULT WITH YOUR GLOVE AND/OR
PROTECTIVE CLOTHING MANUFACTURER FOR SELECTION OF APPROPRIATE COMPATIBLE
MATERIALS.
8.2.3 RESPIRATORY PROTECTION:
SELECT ONE OF THE FOLLOWING NIOSH APPROVED RESPIRATORS BASED ON AIRBORNE
CONCENTRATION OF CONTAMINANTS AND IN ACCORDANCE WITH OSHA REGULATIONS:
HALF FACEPIECE OR FULLFACE AIR-PURIFYING RESPIRATOR WITH ORGANIC VAPOR
CARTRIDGES. CONSULT THE CURRENT 3M RESPIRATORY SELECTION GUIDE FOR
ADDITIONAL INFORMATION OR CALL 1-800-243-4630 FOR 3M TECHNICAL ASSISTANCE.
8.2.4 PREVENTION OF SWALLOWING:
DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT. WASH EXPOSED AREAS
THOROUGHLY WITH SOAP AND WATER. WASH HANDS AFTER HANDLING AND BEFORE
EATING.
8.3 EXPOSURE GUIDELINES:
INGREDIENT AUTHORITY TYPE LIMIT ADDITIONAL
INFORMATION
BUTANE ACGIH TWA 1000 PPM
BUTANE OSHA TWA 800 PPM TABLE Z-1A
PETROLEUM OIL CMRG TWA 5 MG/M3
PETROLEUM OIL CMRG STEL 10 MG/M3
ALIPHATIC HYDROCARBON CMRG TWA 300 PPM
PROPANE ACGIH TWA 1000 PPM
PROPANE OSHA TWA 1000 PPM TABLE Z-1
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
CMRG: CHEMICAL MANUFACTURER RECOMMENDED GUIDELINE
OSHA: OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION
AIHA:
AMERICAN INDUSTRIAL HYGIENE ASSOCIATION WORKPLACE ENVIRONMENTAL EXPOSURE
LEVEL (WEEL)
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
ODOR, COLOR, GRADE: AMBER COLORED LIQUID, STRONG SOLVENT ODOR
GENERAL PHYSICAL FORM: GAS
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
FLASH POINT: 00 DEG. F
FLAMMABLE LIMITS - LEL: 0.6
FLAMMABLE LIMITS - UEL: 9.5
BOILING POINT: </=458
VAPOR DENSITY: 2 (REF STD: AIR=1)
VAPOR PRESSURE: NO DATA AVAILABLE
SPECIFIC GRAVITY: 0.72 (REF STD: WATER=1)
pH: NO DATA AVAILABLE
MELTING POINT: NOT APPLICABLE
SOLUBILITY IN WATER: NO DATA AVAILABLE
VOLATILE ORGANIC COMPOUNDS: 30 % WEIGHT
| SECTION 10: STABILITY AND REACTIVITY | |
STABILITY: STABLE.
MATERIALS AND CONDITIONS TO AVOID: SPARKS AND/OR FLAMES
HAZARDOUS POLYMERIZATION: HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
| SECTION 11: TOXICOLOGICAL INFORMATION | |
PLEASE CONTACT THE ADDRESS LISTED IN SECTION 1 OF THIS MSDS FOR
TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION: NOT DETERMINED.
CHEMICAL FATE INFORMATION: NOT DETERMINED.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
WASTE DISPOSAL METHOD:
DO NOT PUNCTURE OR BURN CANS IN A HOUSEHOLD INCINERATOR. INCINERATE IN A
PERMITTED HAZARDOUS WASTE INCINERATOR. THE FACILITY SHOULD BE EQUIPPED TO
HANDLE GASEOUS WASTE.
FACILITY MUST BE CAPABLE OF HANDLING AEROSOL CANS.
EPA HAZARDOUS WASTE NUMBER (RCRA): D001 (IGNITABLE)
SINCE REGULATIONS VARY, CONSULT APPLICABLE REGULATIONS OR AUTHORITIES
BEFORE DISPOSAL.
| SECTION 14: TRANSPORT INFORMATION | |
ID NUMBER(S): 62-4978-4930-7, 62-4978-4935-6
PLEASE CONTACT THE EMERGENCY NUMBERS LISTED IN SECTION 1 OF THIS MSDS
FOR TRANSPORTATION INFORMATION FOR THIS MATERIAL.
| SECTION 15: REGULATORY INFORMATION | |
US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
311/312 HAZARD CATEGORIES:
FIRE HAZARD: YES
PRESSURE HAZARD: YES
REACTIVITY HAZARD: NO
IMMEDIATE HAZARD: YES
DELAYED HAZARD: NO
STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
CHEMICAL INVENTORIES:
THE COMPONENTS OF THIS PRODUCT ARE IN COMPLIANCE WITH THE CHEMICAL
NOTIFICATION REQUIREMENTS OF TSCA.
ALL APPLICABLE CHEMICAL INGREDIENTS IN THIS MATERIAL ARE LISTED ON THE
EUROPEAN INVENTORY OF EXISTING CHEMICAL SUBSTANCES (EINECS), OR ARE EXEMPT
POLYMERS WHOSE MONOMERS ARE LISTED ON EINECS.
CONTACT 3M FOR MORE INFORMATION.
INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS MSDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 2
FLAMMABILITY 4
REACTIVITY 0
SPECIAL HAZARDS NONE
AEROSOL STORAGE CODE: 3
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED FOR
USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO INCLUDE
THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT ARE KNOWN
TO BE GENERATED IN SIGNIFICANT QUANTITIES.
REVISION CHANGES: COPYRIGHT WAS MODIFIED.
SECTION 3: IMMEDIATE PHYSICAL HAZARD(S) WAS MODIFIED.
SECTION 5: UNUSUAL FIRE AND EXPLOSION HAZARD INFORMATION WAS MODIFIED.
DISCLAIMER:
THE INFORMATION IN THIS MATERIAL SAFETY DATA SHEET (MSDS) IS BELIEVED TO BE
CORRECT AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF
PERFORMANCE OR USAGE OF TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER
THE 3M PRODUCT IS FIT FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S
METHOD OF USE OR APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT
THE USE AND APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN
THE USER'S KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE
THE 3M PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED IN
ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY.
IN ADDITION, INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS
THE INFORMATION IN THE MSDS AVAILABLE DIRECTLY FROM 3M.
3M MSDSS ARE AVAILABLE AT WWW.3M.COM