| Common Name: | RITE-LOK HYDRAULIC PNEUMATIC SEALANT HP45-1, HP45-50, & HP45-250 |
| Manufacturer: | 3M |
| SDS Revision Date: | 7/24/2007 |
| SDS Format: | No Format Specified |
| Item Number(s): | 2XLL9, 2XLN1 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M
MATERIAL SAFETY DATA SHEET
RITE-LOK(TM) HYDRAULIC PNEUMATIC SEALANT HP45-1, HP45-50, & HP45-250
07/24/2007
3M
MATERIAL SAFETY DATA SHEET
COPYRIGHT, 2007, 3M COMPANY. ALL RIGHTS RESERVED. COPYING AND/OR
DOWNLOADING OF THIS INFORMATION FOR THE PURPOSE OF PROPERLY UTILIZING 3M
PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
| SECTION 1: PRODUCT AND COMPANY IDENTIFICATION |  |
PRODUCT NAME:
RITE-LOK(TM) HYDRAULIC PNEUMATIC SEALANT HP45-1, HP45-50, & HP45-250
MANUFACTURER: 3M
DIVISION: INDUSTRIAL ADHESIVES AND TAPES DIVISION
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 OR (651) 737-6501 (24 HOURS)
ISSUE DATE: 07/24/2007
SUPERCEDES DATE: 05/15/2007
DOCUMENT GROUP: 22-6490-1
PRODUCT USE:
SPECIFIC USE: ANAEROBIC SEALANT FOR HYDRAULIC AND PNEUMATIC FITTINGS
INTENDED USE: SEALANT
| SECTION 2: INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
POLYGLYCOL DIOCTANOATE 18268-70-7 15 - 40
POLYGLYCOL DIMETHACRYLATE 25852-47-5 10 - 30
POLYESTER RESIN TRADE SECRET 10 - 30
HYDROXYPROPYL METHACRYLATE 27813-02-1 10 - 30
AMORPHOUS TREATED SILICA 112945-52-5 1 - 5
2-HYDROXYETHYL METHACRYLATE 868-77-9 1 - 5
CUMENE HYDROPEROXIDE 80-15-9 1 - 5
SACCHARIN 81-07-2 0.1 - 1
METHYL ALCOHOL 67-56-1 0.1 - 1
CUMENE 98-82-8 0.1 - 1
1-ACETYL-2-PHENYLHYDRAZINE 114-83-0 0.1 - 1
N,N-DIALKYLTOLUIDINE 613-48-9 0.1 - 1
| SECTION 3: HAZARDS IDENTIFICATION | |
3.1 EMERGENCY OVERVIEW:
SPECIFIC PHYSICAL FORM: PASTE
ODOR, COLOR, GRADE: PURPLE PASTE, ACRYLATE ODOR.
GENERAL PHYSICAL FORM: LIQUID
IMMEDIATE HEALTH, PHYSICAL, AND ENVIRONMENTAL HAZARDS:
HAZARDOUS POLYMERIZATION MAY OCCUR. MAY CAUSE SEVERE EYE IRRITATION. MAY
CAUSE ALLERGIC SKIN REACTION. MAY CAUSE TARGET ORGAN EFFECTS. CONTAINS A
CHEMICAL OR CHEMICALS WHICH CAN CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE
HARM.
3.2 POTENTIAL HEALTH EFFECTS:
EYE CONTACT:
SEVERE EYE IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE SIGNIFICANT REDNESS, SWELLING, PAIN, TEARING,
CLOUDY APPEARANCE OF THE CORNEA, AND IMPAIRED VISION.
VAPORS RELEASED DURING CURING MAY CAUSE EYE IRRITATION. SIGNS/SYMPTOMS MAY
INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND BLURRED OR HAZY VISION.
SKIN CONTACT:
MODERATE SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE LOCALIZED REDNESS, SWELLING, ITCHING, AND
DRYNESS.
PROLONGED OR REPEATED EXPOSURE MAY CAUSE:
ALLERGIC SKIN REACTION (NON-PHOTO INDUCED):
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, BLISTERING, AND ITCHING.
MAY BE ABSORBED THROUGH SKIN AND CAUSE TARGET ORGAN EFFECTS.
INHALATION:
RESPIRATORY TRACT IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL DISCHARGE, HEADACHE,
HOARSENESS, AND NOSE AND THROAT PAIN.
PROLONGED OR REPEATED EXPOSURE MAY CAUSE:
RESPIRATORY EFFECTS:
SIGNS/SYMPTOMS MAY INCLUDE COUGH, SHORTNESS OF BREATH, CHEST TIGHTNESS,
WHEEZING, INCREASED HEART RATE, BLUISH COLORED SKIN (CYANOSIS), SPUTUM
PRODUCTION, CHANGES IN LUNG FUNCTION TESTS, AND/OR RESPIRATORY FAILURE.
MAY BE ABSORBED FOLLOWING INHALATION AND CAUSE TARGET ORGAN EFFECTS.
INGESTION:
GASTROINTESTINAL IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABDOMINAL PAIN, STOMACH UPSET, NAUSEA, VOMITING
AND DIARRHEA.
MAY BE ABSORBED FOLLOWING INGESTION AND CAUSE TARGET ORGAN EFFECTS.
TARGET ORGAN EFFECTS:
PROLONGED OR REPEATED EXPOSURE MAY CAUSE:
NEUROLOGICAL EFFECTS:
SIGNS/SYMPTOMS MAY INCLUDE PERSONALITY CHANGES, LACK OF COORDINATION,
SENSORY LOSS, TINGLING OR NUMBNESS OF THE EXTREMITIES, WEAKNESS, TREMORS,
AND/OR CHANGES IN BLOOD PRESSURE AND HEART RATE.
CONTAINS A CHEMICAL OR CHEMICALS WHICH CAN CAUSE BIRTH DEFECTS OR OTHER
REPRODUCTIVE HARM.
| SECTION 4: FIRST AID MEASURES | |
4.1 FIRST AID PROCEDURES:
THE FOLLOWING FIRST AID RECOMMENDATIONS ARE BASED ON AN ASSUMPTION THAT
APPROPRIATE PERSONAL AND INDUSTRIAL HYGIENE PRACTICES ARE FOLLOWED.
EYE CONTACT:
IMMEDIATELY FLUSH EYES WITH LARGE AMOUNTS OF WATER FOR AT LEAST 15 MINUTES.
GET IMMEDIATE MEDICAL ATTENTION.
SKIN CONTACT:
REMOVE CONTAMINATED CLOTHING AND SHOES. IMMEDIATELY FLUSH SKIN WITH LARGE
AMOUNTS OF WATER. GET MEDICAL ATTENTION. WASH CONTAMINATED CLOTHING AND
CLEAN SHOES BEFORE REUSE.
INHALATION:
REMOVE PERSON TO FRESH AIR. IF SIGNS/SYMPTOMS DEVELOP, GET MEDICAL
ATTENTION.
IF SWALLOWED:
DO NOT INDUCE VOMITING UNLESS INSTRUCTED TO DO SO BY MEDICAL PERSONNEL.
GIVE VICTIM TWO GLASSES OF WATER. NEVER GIVE ANYTHING BY MOUTH TO AN
UNCONSCIOUS PERSON. GET MEDICAL ATTENTION.
| SECTION 5: FIRE FIGHTING MEASURES | |
5.1 FLAMMABLE PROPERTIES:
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
FLASH POINT: >/=200 DEG. F (TEST METHOD: CLOSED CUP)
FLAMMABLE LIMITS - LEL: NO DATA AVAILABLE
FLAMMABLE LIMITS - UEL: NO DATA AVAILABLE
5.2 EXTINGUISHING MEDIA:
USE FIRE EXTINGUISHERS WITH CLASS B EXTINGUISHING AGENTS
(E.G., DRY CHEMICAL, CARBON DIOXIDE).
5.3 PROTECTION OF FIRE FIGHTERS:
SPECIAL FIRE FIGHTING PROCEDURES:
WATER MAY NOT EFFECTIVELY EXTINGUISH FIRE; HOWEVER, IT SHOULD BE USED TO
KEEP FIRE-EXPOSED CONTAINERS AND SURFACES COOL AND PREVENT EXPLOSIVE
RUPTURE. WATER MAY BE USED TO BLANKET THE FIRE. WEAR FULL PROTECTIVE
EQUIPMENT (BUNKER GEAR) AND A SELF-CONTAINED BREATHING APPARATUS (SCBA).
UNUSUAL FIRE AND EXPLOSION HAZARDS:
NO UNUSUAL FIRE OR EXPLOSION HAZARDS ARE ANTICIPATED.
NOTE:
SEE STABILITY AND REACTIVITY (SECTION 10) FOR HAZARDOUS COMBUSTION AND
THERMAL DECOMPOSITION INFORMATION.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
ACCIDENTAL RELEASE MEASURES:
OBSERVE PRECAUTIONS FROM OTHER SECTIONS. CALL 3M- HELPS LINE
(1-800-364-3577) FOR MORE INFORMATION ON HANDLING AND MANAGING THE SPILL.
EVACUATE UNPROTECTED AND UNTRAINED PERSONNEL FROM HAZARD AREA. THE SPILL
SHOULD BE CLEANED UP BY QUALIFIED PERSONNEL. VENTILATE THE AREA WITH FRESH
AIR. FOR LARGE SPILL, OR SPILLS IN CONFINED SPACES, PROVIDE MECHANICAL
VENTILATION TO DISPERSE OR EXHAUST VAPORS, IN ACCORDANCE WITH GOOD
INDUSTRIAL HYGIENE PRACTICE.
WARNING!
A MOTOR COULD BE AN IGNITION SOURCE AND COULD CAUSE FLAMMABLE GASES OR
VAPORS IN THE SPILL AREA TO BURN OR EXPLODE. CONTAIN SPILL. WORKING FROM
AROUND THE EDGES OF THE SPILL INWARD, COVER WITH BENTONITE, VERMICULITE,
OR COMMERCIALLY AVAILABLE INORGANIC ABSORBENT MATERIAL. MIX IN SUFFICIENT
ABSORBENT UNTIL IT APPEARS DRY. COLLECT AS MUCH OF THE SPILLED MATERIAL
AS POSSIBLE. CLEAN UP RESIDUE WITH AN APPROPRIATE SOLVENT SELECTED BY A
QUALIFIED AND AUTHORIZED PERSON. VENTILATE THE AREA WITH FRESH AIR. READ
AND FOLLOW SAFETY PRECAUTIONS ON THE SOLVENT LABEL AND MSDS. COLLECT THE
RESULTING RESIDUE CONTAINING SOLUTION. PLACE IN A CLOSED CONTAINER APPROVED
FOR TRANSPORTATION BY APPROPRIATE AUTHORITIES. DISPOSE OF COLLECTED
MATERIAL AS SOON AS POSSIBLE.
IN THE EVENT OF A RELEASE OF THIS MATERIAL, THE USER SHOULD DETERMINE IF
THE RELEASE QUALIFIES AS REPORTABLE ACCORDING TO LOCAL, STATE, AND FEDERAL
REGULATIONS.
| SECTION 7: HANDLING AND STORAGE | |
7.1 HANDLING:
AVOID EYE CONTACT. DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT. WASH
EXPOSED AREAS THOROUGHLY WITH SOAP AND WATER. AVOID BREATHING OF VAPORS,
MISTS OR SPRAY. AVOID SKIN CONTACT. AVOID BREATHING OF VAPORS CREATED
DURING CURE CYCLE. AVOID EYE CONTACT WITH VAPORS, MISTS, OR SPRAY. KEEP OUT
OF THE REACH OF CHILDREN. KEEP CONTAINER CLOSED WHEN NOT IN USE. FOR
INDUSTRIAL OR PROFESSIONAL USE ONLY. AVOID CONTACT WITH OXIDIZING AGENTS.
USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST VENTILATION TO
CONTROL AIRBORNE EXPOSURES TO BELOW OCCUPATIONAL EXPOSURE LIMITS. IF
VENTILATION IS NOT ADEQUATE, USE RESPIRATORY PROTECTION EQUIPMENT.
7.2 STORAGE:
STORE AWAY FROM HEAT. STORE OUT OF DIRECT SUNLIGHT. KEEP CONTAINER IN
WELL-VENTILATED AREA. KEEP CONTAINER TIGHTLY CLOSED. STORE AWAY FROM
OXIDIZING AGENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1 ENGINEERING CONTROLS:
CURING ENCLOSURES MUST BE EXHAUSTED TO OUTDOORS OR TO A SUITABLE EMISSION
CONTROL DEVICE. USE GENERAL DILUTION VENTILATION AND/OR LOCAL EXHAUST
VENTILATION TO CONTROL AIRBORNE EXPOSURES TO BELOW OCCUPATIONAL EXPOSURE
LIMITS AND/OR CONTROL MIST, VAPOR, OR SPRAY. IF VENTILATION IS NOT
ADEQUATE, USE RESPIRATORY PROTECTION EQUIPMENT.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE):
8.2.1 EYE/FACE PROTECTION: AVOID EYE CONTACT.
THE FOLLOWING EYE PROTECTION(S) ARE RECOMMENDED:
SAFETY GLASSES WITH SIDE SHIELDS, INDIRECT VENTED GOGGLES.
8.2.2 SKIN PROTECTION: AVOID SKIN CONTACT.
SELECT AND USE GLOVES AND/OR PROTECTIVE CLOTHING TO PREVENT SKIN CONTACT
BASED ON THE RESULTS OF AN EXPOSURE ASSESSMENT. CONSULT WITH YOUR GLOVE
AND/OR PROTECTIVE CLOTHING MANUFACTURER FOR SELECTION OF APPROPRIATE
COMPATIBLE MATERIALS.
GLOVES MADE FROM THE FOLLOWING MATERIAL(S) ARE RECOMMENDED:
POLYVINYL ALCOHOL (PVA).
8.2.3 RESPIRATORY PROTECTION:
AVOID BREATHING OF VAPORS, MISTS OR SPRAY. AVOID BREATHING OF VAPORS
CREATED DURING CURE CYCLE.
SELECT ONE OF THE FOLLOWING NIOSH APPROVED RESPIRATORS BASED ON AIRBORNE
CONCENTRATION OF CONTAMINANTS AND IN ACCORDANCE WITH OSHA REGULATIONS:
HALF FACEPIECE OR FULLFACE AIR-PURIFYING RESPIRATOR WITH ORGANIC VAPOR
CARTRIDGES. CONSULT THE CURRENT 3M RESPIRATORY SELECTION GUIDE FOR
ADDITIONAL INFORMATION OR CALL 1-800-243-4630 FOR 3M TECHNICAL ASSISTANCE.
8.2.4 PREVENTION OF SWALLOWING:
DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT. WASH EXPOSED AREAS
THOROUGHLY WITH SOAP AND WATER.
8.3 EXPOSURE GUIDELINES:
INGREDIENT AUTHORITY TYPE LIMIT ADDITIONAL
INFORMATION
CUMENE ACGIH TWA 50 PPM
CUMENE OSHA TWA 50 PPM SKIN NOTATION*
TABLE Z-1
CUMENE HYDROPEROXIDE AIHA TWA 1 PPM SKIN NOTATION*
HYDROXYPROPYL METHACRYLATE CMRG CEIL 3 PPM
METHYL ALCOHOL ACGIH TWA 200 PPM SKIN NOTATION*
METHYL ALCOHOL ACGIH STEL 250 PPM SKIN NOTATION*
METHYL ALCOHOL OSHA TWA 200 PPM SKIN NOTATION*
TABLE Z-1A
METHYL ALCOHOL OSHA STEL 250 PPM SKIN NOTATION*
TABLE Z-1A
* SUBSTANCE(S) REFER TO THE POTENTIAL CONTRIBUTION TO THE OVERALL EXPOSURE
BY THE CUTANEOUS ROUTE INCLUDING MUCOUS MEMBRANE AND EYE, EITHER BY
AIRBORNE OR, MORE PARTICULARLY, BY DIRECT CONTACT WITH THE SUBSTANCE.
VEHICLES CAN ALTER SKIN ABSORPTION.
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
CMRG: CHEMICAL MANUFACTURER RECOMMENDED GUIDELINE
OSHA: OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION
AIHA:
AMERICAN INDUSTRIAL HYGIENE ASSOCIATION WORKPLACE ENVIRONMENTAL EXPOSURE
LEVEL (WEEL)
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
SPECIFIC PHYSICAL FORM: PASTE
ODOR, COLOR, GRADE: PURPLE PASTE, ACRYLATE ODOR.
GENERAL PHYSICAL FORM: LIQUID
AUTOIGNITION TEMPERATURE: NO DATA AVAILABLE
FLASH POINT: >/=200 DEG. F (TEST METHOD: CLOSED CUP)
FLAMMABLE LIMITS - LEL: NO DATA AVAILABLE
FLAMMABLE LIMITS - UEL: NO DATA AVAILABLE
BOILING POINT: >/=149 DEG. C
DENSITY: 1.08 G/ML
VAPOR DENSITY: NO DATA AVAILABLE
VAPOR PRESSURE: </=5 MMHg (@ 80 DEG. F)
SPECIFIC GRAVITY: 1.08 (REF STD: WATER=1)
pH: NOT APPLICABLE
MELTING POINT: NOT APPLICABLE
SOLUBILITY IN WATER: SLIGHT (LESS THAN 10%)
EVAPORATION RATE: NEGLIGIBLE
HAZARDOUS AIR POLLUTANTS: </=0.75% WEIGHT
VOLATILE ORGANIC COMPOUNDS: NO DATA AVAILABLE
VOC LESS H2O & EXEMPT SOLVENTS: NO DATA AVAILABLE
VISCOSITY: 12000 - 16000 CENTIPOISE (@ 73.4 DEG. F)
| SECTION 10: STABILITY AND REACTIVITY | |
STABILITY: STABLE.
MATERIALS AND CONDITIONS TO AVOID:
HEAT; LIGHT; REDUCING AGENTS; STRONG OXIDIZING AGENTS
HAZARDOUS POLYMERIZATION:
HAZARDOUS POLYMERIZATION MAY OCCUR. MAY OCCUR AT ELEVATED TEMPERATURES,
>150F.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
FORMALDEHYDE DURING COMBUSTION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
OXIDES OF NITROGEN DURING COMBUSTION
OXIDES OF SULFUR DURING COMBUSTION
| SECTION 11: TOXICOLOGICAL INFORMATION | |
PLEASE CONTACT THE ADDRESS LISTED IN THE BEGIINING OF THIS MSDS FOR
TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION: NOT DETERMINED.
CHEMICAL FATE INFORMATION: NOT DETERMINED.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
WASTE DISPOSAL METHOD:
CURE (HARDEN, SET, OR REACT) THE PRODUCT ACCORDING TO PRODUCT INSTRUCTIONS.
DISPOSE OF COMPLETELY CURED (OR POLYMERIZED) WASTES IN A SANITARY LANDFILL.
AS A DISPOSAL ALTERNATIVE, INCINERATE UNCURED PRODUCT IN AN INDUSTRIAL OR
COMMERCIAL INCINERATOR.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
SINCE REGULATIONS VARY, CONSULT APPLICABLE REGULATIONS OR AUTHORITIES
BEFORE DISPOSAL.
| SECTION 14: TRANSPORT INFORMATION | |
ID NUMBER(S):
62-3477-0150-0, 62-3477-1055-0, 62-3477-3950-0, 62-3477-5050-7
NOT REGULATED PER U.S. DOT, IATA OR IMO.
THESE TRANSPORTATION CLASSIFICATIONS ARE PROVIDED AS A CUSTOMER SERVICE.
AS THE SHIPPER YOU REMAIN RESPONSIBLE FOR COMPLYING WITH ALL APPLICABLE
LAWS AND REGULATIONS, INCLUDING PROPER TRANSPORTATION CLASSIFICATION AND
PACKAGING. 3M'S TRANSPORTATION CLASSIFICATIONS ARE BASED ON PRODUCT
FORMULATION, PACKAGING, 3M POLICIES AND 3M'S UNDERSTANDING OF APPLICABLE
CURRENT REGULATIONS. 3M DOES NOT GUARANTEE THE ACCURACY OF THIS
CLASSIFICATION INFORMATION. THIS INFORMATION APPLIES ONLY TO TRANSPORTATION
CLASSIFICATION AND NOT THE PACKAGING, LABELING, OR MARKING REQUIREMENTS.
THE ORIGINAL 3M PACKAGE IS CERTIFIED FOR U.S. GROUND SHIPMENT ONLY. IF YOU
ARE SHIPPING BY AIR OR OCEAN, THE PACKAGE MAY NOT MEET APPLICABLE
REGULATORY REQUIREMENTS.
| SECTION 15: REGULATORY INFORMATION | |
US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
311/312 HAZARD CATEGORIES:
FIRE HAZARD: NO
PRESSURE HAZARD: NO
REACTIVITY HAZARD: YES
IMMEDIATE HAZARD: YES
DELAYED HAZARD: YES
SECTION 313 TOXIC CHEMICALS SUBJECT TO THE REPORTING REQUIREMENTS OF THAT
SECTION AND 40 CFR PART 372 (EPCRA):
INGREDIENT C.A.S. NO % BY WT
CUMENE HYDROPEROXIDE 80-15-9 1 - 5
STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
CHEMICAL INVENTORIES:
THE COMPONENTS OF THIS PRODUCT ARE IN COMPLIANCE WITH THE CHEMICAL
NOTIFICATION REQUIREMENTS OF TSCA.
CONTACT 3M FOR MORE INFORMATION.
INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
WHMIS: HAZARDOUS
THIS MSDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 2
FLAMMABILITY 1
REACTIVITY 1
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED FOR
USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO INCLUDE
THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT ARE KNOWN
TO BE GENERATED IN SIGNIFICANT QUANTITIES.
REVISION CHANGES:
SECTION 1: PRODUCT NAME WAS MODIFIED.
MSDS HEADING: PRODUCT NAME WAS MODIFIED.
DISCLAIMER:
THE INFORMATION IN THIS MATERIAL SAFETY DATA SHEET (MSDS) IS BELIEVED TO BE
CORRECT AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF
PERFORMANCE OR USAGE OF TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER
THE 3M PRODUCT IS FIT FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S
METHOD OF USE OR APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT
THE USE AND APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN
THE USER'S KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE
THE 3M PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE MSDS AVAILABLE DIRECTLY FROM 3M.
3M MSDSS ARE AVAILABLE AT WWW.3M.COM