| Common Name: | SCOTCH-WELD CONCRETE REPAIR 600, SELF-LEVELING, GRAY (PART B) |
| Manufacturer: | 3M |
| SDS Revision Date: | 2/20/2007 |
| SDS Format: | No Format Specified |
| Item Number(s): | 4TY40, 4TY41, 4TY42, 4TY43, 4TY45 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
3M
MATERIAL SAFETY DATA SHEET
3M(TM) SCOTCH-WELD(TM) CONCRETE REPAIR 600, SELF-LEVELING, GRAY (PART B)
02/20/2007
3M
MATERIAL SAFETY DATA SHEET
COPYRIGHT, 2007, 3M COMPANY. ALL RIGHTS RESERVED. COPYING AND/OR
DOWNLOADING OF THIS INFORMATION FOR THE PURPOSE OF PROPERLY UTILIZING 3M
PRODUCTS IS ALLOWED PROVIDED THAT:
(1) THE INFORMATION IS COPIED IN FULL WITH NO CHANGES UNLESS PRIOR WRITTEN
AGREEMENT IS OBTAINED FROM 3M, AND
(2) NEITHER THE COPY NOR THE ORIGINAL IS RESOLD OR OTHERWISE DISTRIBUTED
WITH THE INTENTION OF EARNING A PROFIT THEREON.
| SECTION 1: PRODUCT AND COMPANY IDENTIFICATION |  |
PRODUCT NAME:
3M(TM) SCOTCH-WELD(TM) CONCRETE REPAIR 600, SELF-LEVELING, GRAY (PART B)
MANUFACTURER: 3M
DIVISION: INDUSTRIAL ADHESIVES AND TAPES DIVISION
ADDRESS:
3M CENTER
ST. PAUL, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 OR (651) 737-6501 (24 HOURS)
ISSUE DATE: 02/20/2007
SUPERCEDES DATE: 08/29/2006
DOCUMENT GROUP: 18-0901-1
PRODUCT USE:
SPECIFIC USE: TWO-PART URETHANE ADHESIVE/SEALANT.
INTENDED USE: STRUCTURAL ADHESIVE
FORMERLY KNOWN AS DYNAMIX(TM) SELF-LEVELING RAPID REPAIR 6143-1, GRAY.
| SECTION 2: INGREDIENTS | |
INGREDIENT C.A.S. NO. % BY WT
POLYETHER POLYOL 9082-00-2 40 - 70
PROPOXYLATED TRIMETHYLOLPROPANE 25723-16-4 10 - 30
TETRAKIS(2-HYDROXYPROPYL)ETHYLENEDIAMINE 102-60-3 10 - 30
AMORPHOUS SILICA 68611-44-9 1 - 5
m-XYLENE-ALPHA,ALPHA-DIAMINE 1477-55-0 0.1 - 1
BIS(1,2,2,6,6-PENTAMETHYL-4-PIPERIDINYL)SEBACATE 41556-26-7 0.1 - 1
POLYMERIC BENZOTRIAZOLE DERIVATIVE 104810-48-2 0.1 - 0.3
POLYMERIC BENZOTRIAZOLE 104810-47-1 0.1 - 0.3
SUBSTITUTED PIPERYDINYL SEBACATE 82919-37-7 0.05 - 0.2
| SECTION 3: HAZARDS IDENTIFICATION | |
3.1 EMERGENCY OVERVIEW:
SPECIFIC PHYSICAL FORM: VISCOUS
ODOR, COLOR, GRADE; SLIGHT AMMONIA LIKE ODOR, GRAY.
GENERAL PHYSICAL FORM: LIQUID
IMMEDIATE HEALTH, PHYSICAL, AND ENVIRONMENTAL HAZARDS:
MAY CAUSE ALLERGIC SKIN REACTION.
3.2 POTENTIAL HEALTH EFFECTS:
EYE CONTACT:
MODERATE EYE IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND BLURRED
OR HAZY VISION.
VAPORS RELEASED DURING CURING MAY CAUSE EYE IRRITATION. SIGNS/SYMPTOMS MAY
INCLUDE REDNESS, SWELLING, PAIN, TEARING, AND BLURRED OR HAZY VISION.
DUST CREATED BY CUTTING, GRINDING, SANDING, OR MACHINING MAY CAUSE EYE
IRRITATION. SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, PAIN, TEARING,
AND BLURRED OR HAZY VISION.
SKIN CONTACT:
MILD SKIN IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE LOCALIZED REDNESS, SWELLING, AND ITCHING.
PROLONGED OR REPEATED EXPOSURE MAY CAUSE:
ALLERGIC SKIN REACTION (NON-PHOTO INDUCED):
SIGNS/SYMPTOMS MAY INCLUDE REDNESS, SWELLING, BLISTERING, AND ITCHING.
INHALATION:
VAPORS RELEASED DURING CURING MAY CAUSE IRRITATION OF THE RESPIRATORY
SYSTEM. SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL DISCHARGE,
HEADACHE, HOARSENESS, AND NOSE AND THROAT PAIN.
DUST FROM CUTTING, GRINDING, SANDING OR MACHINING MAY CAUSE IRRITATION OF
THE RESPIRATORY SYSTEM. SIGNS/SYMPTOMS MAY INCLUDE COUGH, SNEEZING, NASAL
DISCHARGE, HEADACHE, HOARSENESS, AND NOSE AND THROAT PAIN.
INGESTION:
GASTROINTESTINAL IRRITATION:
SIGNS/SYMPTOMS MAY INCLUDE ABDOMINAL PAIN, NAUSEA, DIARRHEA AND VOMITING.
| SECTION 4: FIRST AID MEASURES | |
4.1 FIRST AID PROCEDURES:
THE FOLLOWING FIRST AID RECOMMENDATIONS ARE BASED ON AN ASSUMPTION THAT
APPROPRIATE PERSONAL AND INDUSTRIAL HYGIENE PRACTICES ARE FOLLOWED.
EYE CONTACT:
FLUSH EYES WITH LARGE AMOUNTS OF WATER. IF SIGNS/SYMPTOMS PERSIST, GET
MEDICAL ATTENTION.
SKIN CONTACT:
REMOVE CONTAMINATED CLOTHING AND SHOES. IMMEDIATELY FLUSH SKIN WITH LARGE
AMOUNTS OF WATER. GET MEDICAL ATTENTION. WASH CONTAMINATED CLOTHING AND
CLEAN SHOES BEFORE REUSE.
INHALATION:
IF SIGNS/SYMPTOMS DEVELOP, REMOVE PERSON TO FRESH AIR. IF SIGNS/SYMPTOMS
PERSIST, GET MEDICAL ATTENTION.
IF SWALLOWED:
DO NOT INDUCE VOMITING. GIVE VICTIM TWO GLASSES OF WATER. NEVER GIVE
ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON. GET IMMEDIATE MEDICAL
ATTENTION.
| SECTION 5: FIRE FIGHTING MEASURES | |
5.1 FLAMMABLE PROPERTIES:
AUTOIGNITION TEMPERATURE: NOT APPLICABLE
FLASH POINT: >/=290 DEG. F
(TEST METHOD: TAGLIABUE CLOSED CUP)
FLAMMABLE LIMITS - LEL: NOT APPLICABLE
FLAMMABLE LIMITS - UEL: NOT APPLICABLE
5.2 EXTINGUISHING MEDIA:
USE FIRE EXTINGUISHERS WITH CLASS B EXTINGUISHING AGENTS (E.G., DRY
CHEMICAL, CARBON DIOXIDE).
5.3 PROTECTION OF FIRE FIGHTERS:
SPECIAL FIRE FIGHTING PROCEDURES:
WEAR FULL PROTECTIVE EQUIPMENT (BUNKER GEAR) AND A SELF-CONTAINED BREATHING
APPARATUS (SCBA).
UNUSUAL FIRE AND EXPLOSION HAZARDS: NOT APPLICABLE.
NON-FLAMMABLE: ORDINARY COMBUSTIBLE MATERIAL.
NOTE:
SEE STABILITY AND REACTIVITY (SECTION 10) FOR HAZARDOUS COMBUSTION AND
THERMAL DECOMPOSITION INFORMATION.
| SECTION 6: ACCIDENTAL RELEASE MEASURES | |
ACCIDENTAL RELEASE MEASURES:
OBSERVE PRECAUTIONS FROM OTHER SECTIONS. CALL 3M-HELPS LINE
(1-800-364-3577) FOR MORE INFORMATION ON HANDLING AND MANAGING THE SPILL.
EVACUATE UNPROTECTED AND UNTRAINED PERSONNEL FROM HAZARD AREA. THE SPILL
SHOULD BE CLEANED UP BY QUALIFIED PERSONNEL. VENTILATE THE AREA WITH FRESH
AIR. FOR LARGE SPILL, OR SPILLS IN CONFINED SPACES, PROVIDE MECHANICAL
VENTILATION TO DISPERSE OR EXHAUST VAPORS, IN ACCORDANCE WITH GOOD
INDUSTRIAL HYGIENE PRACTICE.
WARNING!
A MOTOR COULD BE AN IGNITION SOURCE AND COULD CAUSE FLAMMABLE GASES OR
VAPORS IN THE SPILL AREA TO BURN OR EXPLODE. CONTAIN SPILL. FOR LARGER
SPILLS, COVER DRAINS AND BUILD DIKES TO PREVENT ENTRY INTO SEWER SYSTEMS
OR BODIES OF WATER. COLLECT AS MUCH OF THE SPILLED MATERIAL AS POSSIBLE.
CLEAN UP RESIDUE WITH AN APPROPRIATE ORGANIC SOLVENT. READ AND FOLLOW
SAFETY PRECAUTIONS ON THE SOLVENT LABEL AND MSDS. COLLECT THE RESULTING
RESIDUE CONTAINING SOLUTION. PLACE IN A CLOSED CONTAINER APPROVED FOR
TRANSPORTATION BY APPROPRIATE AUTHORITIES. DISPOSE OF COLLECTED MATERIAL
AS SOON AS POSSIBLE.
IN THE EVENT OF A RELEASE OF THIS MATERIAL, THE USER SHOULD DETERMINE IF
THE RELEASE QUALIFIES AS REPORTABLE ACCORDING TO LOCAL, STATE, AND FEDERAL
REGULATIONS.
| SECTION 7: HANDLING AND STORAGE | |
7.1 HANDLING:
DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT. WASH EXPOSED AREAS
THOROUGHLY WITH SOAP AND WATER. AVOID EYE CONTACT WITH VAPORS, MISTS, OR
SPRAY. AVOID BREATHING OF DUST CREATED BY CUTTING, SANDING, GRINDING OR
MACHINING. AVOID CONTACT WITH OXIDIZING AGENTS.
7.2 STORAGE: STORE AWAY FROM ACIDS. STORE AWAY FROM OXIDIZING AGENTS.
| SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION | |
8.1 ENGINEERING CONTROLS:
PROVIDE APPROPRIATE LOCAL EXHAUST FOR CUTTING, GRINDING, SANDING OR
MACHINING.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE):
8.2.1 EYE/FACE PROTECTION: AVOID EYE CONTACT WITH VAPORS, MISTS, OR SPRAY.
8.2.2 SKIN PROTECTION: AVOID SKIN CONTACT.
SELECT AND USE GLOVES AND/OR PROTECTIVE CLOTHING TO PREVENT SKIN CONTACT
BASED ON THE RESULTS OF AN EXPOSURE ASSESSMENT. CONSULT WITH YOUR GLOVE
AND/OR PROTECTIVE CLOTHING MANUFACTURER FOR SELECTION OF APPROPRIATE
COMPATIBLE MATERIALS.
GLOVES MADE FROM THE FOLLOWING MATERIAL(S) ARE RECOMMENDED: BUTYL RUBBER.
8.2.3 RESPIRATORY PROTECTION:
UNDER NORMAL USE CONDITIONS, AIRBORNE EXPOSURES ARE NOT EXPECTED TO BE
SIGNIFICANT ENOUGH TO REQUIRE RESPIRATORY PROTECTION. AVOID BREATHING OF
DUST CREATED BY CUTTING, SANDING, GRINDING OR MACHINING. CONSULT THE
CURRENT 3M RESPIRATOR SELECTION GUIDE FOR ADDITIONAL INFORMATION OR CALL
1-800-243-4630 FOR 3M TECHNICAL ASSISTANCE.
DURING APPLICATION AND CURING:
SELECT ONE OF THE FOLLOWING NIOSH APPROVED RESPIRATORS BASED ON AIRBORNE
CONCENTRATION OF CONTAMINANTS AND IN ACCORDANCE WITH OSHA REGULATIONS:
HALF FACEPIECE OR FULLFACE AIR-PURIFYING RESPIRATOR WITH ORGANIC VAPOR
CARTRIDGES.
CUTTING, GRINDING OR SANDING CURED MATERIAL:
SELECT ONE OF THE FOLLOWING NIOSH APPROVED RESPIRATORS BASED ON AIRBORNE
CONCENTRATION OF CONTAMINANTS AND IN ACCORDANCE WITH OSHA REGULATIONS:
AIR-PURIFYING RESPIRATOR WITH N95 FILTER.
8.2.4 PREVENTION OF SWALLOWING:
DO NOT EAT, DRINK OR SMOKE WHEN USING THIS PRODUCT. WASH EXPOSED AREAS
THOROUGHLY WITH SOAP AND WATER.
8.3 EXPOSURE GUIDELINES:
INGREDIENT AUTHORITY TYPE LIMIT ADDITIONAL
INFORMATION
BIS(1,2,2,6,6-PENTAMETHYL- CMRG TWA 1 MG/M3
4-PIPERIDINYL) SEBACATE
m-XYLENE-ALPHA,ALPHA-DIAMINE ACGIH CEIL 0.1 MG/M3 SKIN NOTATION*
m-XYLENE-ALPHA,ALPHA-DIAMINE OSHA CEIL 0.1 MG/M3 TABLE Z-1A
* SUBSTANCE(S) REFER TO THE POTENTIAL CONTRIBUTION TO THE OVERALL EXPOSURE
BY THE CUTANEOUS ROUTE INCLUDING MUCOUS MEMBRANE AND EYE, EITHER BY
AIRBORNE OR, MORE PARTICULARLY, BY DIRECT CONTACT WITH THE SUBSTANCE.
VEHICLES CAN ALTER SKIN ABSORPTION.
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
CMRG: CHEMICAL MANUFACTURER RECOMMENDED GUIDELINE
OSHA: OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION
AIHA:
AMERICAN INDUSTRIAL HYGIENE ASSOCIATION WORKPLACE ENVIRONMENTAL EXPOSURE
LEVEL (WEEL)
| SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES | |
SPECIFIC PHYSICAL FORM: VISCOUS
ODOR, COLOR, GRADE: SLIGHT AMMONIA LIKE ODOR, GRAY.
GENERAL PHYSICAL FORM: LIQUID
AUTOIGNITION TEMPERATURE: NOT APPLICABLE
FLASH POINT: >/=290 DEG. F
(TEST METHOD: TAGLIABUE CLOSED CUP)
FLAMMABLE LIMITS - LEL: NOT APPLICABLE
FLAMMABLE LIMITS - UEL: NOT APPLICABLE
BOILING POINT: >/=400 DEG. F
VAPOR DENSITY >/=1 (REF STD: AIR=1)
VAPOR PRESSURE: NOT APPLICABLE
SPECIFIC GRAVITY: 1.04
pH: NOT APPLICABLE
MELTING POINT: NO DATA AVAILABLE
SOLUBILITY IN WATER: NEGLIGIBLE
EVAPORATION RATE: </=1 (REF STD: WATER=1)
HAZARDOUS AIR POLLUTANTS: 00 % WEIGHT (TEST METHOD: CALCULATED)
VOLATILE ORGANIC COMPOUNDS:
</=10 G/L (TEST METHOD: CALCULATED PER EPA METHOD 24)
VOLATILE ORGANIC COMPOUNDS
</=5 G/L (TEST METHOD: CALCULATED PER EPA METHOD 24)
(DETAILS: MIXED 1:1 WITH PART A)
PERCENT VOLATILE: </=1 % VOLUME (TEST METHOD: ESTIMATED)
PERCENT VOLATILE:
</=0.5 % VOLUME (TEST METHOD: ESTIMATED)
(DETAILS: WHEN MIXED 1:1 WITH PART A)
VOC LESS H2O & EXEMPT SOLVENTS:
</=10 G/L (TEST METHOD: CALCULATED PER EPA METHOD 24)
VOC LESS H2O & EXEMPT SOLVENTS:
</=5 G/L (TEST METHOD: CALCULATED PER EPA METHOD 24)
(DETAILS: MIXED 1:1 WITH PART A)
VISCOSITY: 3,200 - 5,600 CENTIPOISE
| SECTION 10: STABILITY AND REACTIVITY | |
STABILITY: STABLE.
MATERIALS AND CONDITIONS TO AVOID: STRONG ACIDS; STRONG OXIDIZING AGENTS
HAZARDOUS POLYMERIZATION: HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
SUBSTANCE CONDITION
CARBON MONOXIDE DURING COMBUSTION
CARBON DIOXIDE DURING COMBUSTION
HYDROGEN CHLORIDE DURING COMBUSTION
OXIDES OF NITROGEN DURING COMBUSTION
| SECTION 11: TOXICOLOGICAL INFORMATION | |
PLEASE CONTACT THE ADDRESS LISTED IN THE BEGINNING OF THIS MSDS
FOR TOXICOLOGICAL INFORMATION ON THIS MATERIAL AND/OR ITS COMPONENTS.
| SECTION 12: ECOLOGICAL INFORMATION | |
ECOTOXICOLOGICAL INFORMATION: NOT DETERMINED.
CHEMICAL FATE INFORMATION: NOT DETERMINED.
| SECTION 13: DISPOSAL CONSIDERATIONS | |
WASTE DISPOSAL METHOD:
DISPOSE OF COMPLETELY CURED (OR POLYMERIZED) WASTES IN A SANITARY LANDFILL.
AS A DISPOSAL ALTERNATIVE, INCINERATE UNCURED PRODUCT IN AN INDUSTRIAL OR
COMMERCIAL INCINERATOR IN THE PRESENCE OF A COMBUSTIBLE MATERIAL.
COMBUSTION PRODUCTS WILL INCLUDE HCl. FACILITY MUST BE CAPABLE OF HANDLING
HALOGENATED MATERIALS.
EPA HAZARDOUS WASTE NUMBER (RCRA): NOT REGULATED
SINCE REGULATIONS VARY, CONSULT APPLICABLE REGULATIONS OR AUTHORITIES
BEFORE DISPOSAL.
| SECTION 14: TRANSPORT INFORMATION | |
ID NUMBER(S): 62-2649-8535-9, 62-2649-9535-8
NOT REGULATED PER U.S. DOT, IATA OR IMO.
THESE TRANSPORTATION CLASSIFICATIONS ARE PROVIDED AS A CUSTOMER SERVICE.
AS THE SHIPPER YOU REMAIN RESPONSIBLE FOR COMPLYING WITH ALL APPLICABLE
LAWS AND REGULATIONS, INCLUDING PROPER TRANSPORTATION CLASSIFICATION AND
PACKAGING. 3M'S TRANSPORTATION CLASSIFICATIONS ARE BASED ON PRODUCT
FORMULATION, PACKAGING, 3M POLICIES AND 3M'S UNDERSTANDING OF APPLICABLE
CURRENT REGULATIONS. 3M DOES NOT GUARANTEE THE ACCURACY OF THIS
CLASSIFICATION INFORMATION. THIS INFORMATION APPLIES ONLY TO TRANSPORTATION
CLASSIFICATION AND NOT THE PACKAGING, LABELING, OR MARKING REQUIREMENTS.
THE ORIGINAL 3M PACKAGE IS CERTIFIED FOR U.S. GROUND SHIPMENT ONLY. IF YOU
ARE SHIPPING BY AIR OR OCEAN, THE PACKAGE MAY NOT MEET APPLICABLE
REGULATORY REQUIREMENTS.
| SECTION 15: REGULATORY INFORMATION | |
US FEDERAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
311/312 HAZARD CATEGORIES:
FIRE HAZARD: NO
PRESSURE HAZARD: NO
REACTIVITY HAZARD: NO
IMMEDIATE HAZARD: YES
DELAYED HAZARD: NO
STATE REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
CHEMICAL INVENTORIES:
THE COMPONENTS OF THIS PRODUCT ARE IN COMPLIANCE WITH THE CHEMICAL
NOTIFICATION REQUIREMENTS OF TSCA.
CONTACT 3M FOR MORE INFORMATION.
INTERNATIONAL REGULATIONS: CONTACT 3M FOR MORE INFORMATION.
THIS MSDS HAS BEEN PREPARED TO MEET THE U.S. OSHA HAZARD COMMUNICATION
STANDARD, 29 CFR 1910.1200.
| SECTION 16: OTHER INFORMATION | |
NFPA HAZARD CLASSIFICATION:
HEALTH 2
FLAMMABILITY 1
REACTIVITY 1
SPECIAL HAZARDS NONE
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) HAZARD RATINGS ARE DESIGNED
FOR USE BY EMERGENCY RESPONSE PERSONNEL TO ADDRESS THE HAZARDS THAT ARE
PRESENTED BY SHORT-TERM, ACUTE EXPOSURE TO A MATERIAL UNDER CONDITIONS OF
FIRE, SPILL, OR SIMILAR EMERGENCIES. HAZARD RATINGS ARE PRIMARILY BASED ON
THE INHERENT PHYSICAL AND TOXIC PROPERTIES OF THE MATERIAL BUT ALSO INCLUDE
THE TOXIC PROPERTIES OF COMBUSTION OR DECOMPOSITION PRODUCTS THAT ARE KNOWN
TO BE GENERATED IN SIGNIFICANT QUANTITIES.
HMIS HAZARD CLASSIFICATION:
HEALTH 2
FLAMMABILITY 1
REACTIVITY 1
PROTECTION X - SEE PPE SECTION.
HAZARDOUS MATERIAL IDENTIFICATION SYSTEM (HMIS(R)) HAZARD RATINGS ARE
DESIGNED TO INFORM EMPLOYEES OF CHEMICAL HAZARDS IN THE WORKPLACE. THESE
RATINGS ARE BASED ON THE INHERENT PROPERTIES OF THE MATERIAL UNDER EXPECTED
CONDITIONS OF NORMAL USE AND ARE NOT INTENDED FOR USE IN EMERGENCY
SITUATIONS. HMIS(R) RATINGS ARE TO BE USED WITH A FULLY IMPLEMENTED HMIS(R)
PROGRAM. HMIS(R) IS A REGISTERED MARK OF THE NATIONAL PAINT AND COATINGS
ASSOCIATION (NPCA).
REVISION CHANGES:
SECTION 1: PRODUCT NAME WAS MODIFIED.
SECTION 1: PRODUCT USE INFORMATION WAS MODIFIED.
COPYRIGHT WAS MODIFIED.
MSDS HEADING: PRODUCT NAME WAS MODIFIED.
DISCLAIMER:
THE INFORMATION IN THIS MATERIAL SAFETY DATA SHEET (MSDS) IS BELIEVED TO
BE CORRECT AS OF THE DATE ISSUED. 3M MAKES NO WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF
PERFORMANCE OR USAGE OF TRADE. USER IS RESPONSIBLE FOR DETERMINING WHETHER
THE 3M PRODUCT IS FIT FOR A PARTICULAR PURPOSE AND SUITABLE FOR USER'S
METHOD OF USE OR APPLICATION. GIVEN THE VARIETY OF FACTORS THAT CAN AFFECT
THE USE AND APPLICATION OF A 3M PRODUCT, SOME OF WHICH ARE UNIQUELY WITHIN
THE USER'S KNOWLEDGE AND CONTROL, IT IS ESSENTIAL THAT THE USER EVALUATE
THE 3M PRODUCT TO DETERMINE WHETHER IT IS FIT FOR A PARTICULAR PURPOSE AND
SUITABLE FOR USER'S METHOD OF USE OR APPLICATION.
3M PROVIDES INFORMATION IN ELECTRONIC FORM AS A SERVICE TO ITS CUSTOMERS.
DUE TO THE REMOTE POSSIBILITY THAT ELECTRONIC TRANSFER MAY HAVE RESULTED
IN ERRORS, OMISSIONS OR ALTERATIONS IN THIS INFORMATION, 3M MAKES NO
REPRESENTATIONS AS TO ITS COMPLETENESS OR ACCURACY. IN ADDITION,
INFORMATION OBTAINED FROM A DATABASE MAY NOT BE AS CURRENT AS THE
INFORMATION IN THE MSDS AVAILABLE DIRECTLY FROM 3M.