| Common Name: | ROHPER 1-GL 2PK V7400 HIGH GLOSS WHITE, 245406 |
| Manufacturer: | RUST-OLEUM |
| SDS Revision Date: | 4/19/2011 |
| SDS Format: | No Format Specified |
| Item Number(s): | 2ZLF8, 2ZLG1, 2ZLG3, 2ZLG5, 2ZLG7, 2ZLG9, 2ZLH2, 2ZLH4, 2ZLH6, 2ZLH8, 2ZLJ1, 2ZLJ3, 2ZLJ5, 2ZLJ7, 2ZLJ9, 2ZLK2, 2ZLK4, 2ZLK8, 2ZLL1, 2ZLL3, 2ZLL5, 2ZLL7, 2ZLL9, 2ZLN2, 2ZLN4, 2ZLN8, 2ZLP1, 2ZLP3, 2ZLP5, 2ZLP7, 2ZLP9, 2ZLR2, 2ZLR4, 2ZLR6, 2ZLR8, 2ZLT1, 2ZLT3, 2ZLT5, 2ZLT7, 2ZLT9, 2ZLU2, 2ZLU4, 2ZLU6, 2ZLU8, 2ZLV1, 2ZLV3, 2ZLV5, 2ZLV7, 2ZLV9, 2ZLW2, 2ZLW4, 2ZLW8, 2ZLX1, 2ZLX3, 2ZLX5, 2ZLX7, 2ZLX9 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
MATERIAL SAFETY DATA SHEET
24 HOUR ASSISTANCE:
1-847-367-7700
RUST-OLEUM CORP.
WWW.RUSTOLEUM.COM
| SECTION 1 - CHEMICAL PRODUCT / COMPANY INFORMATION |  |
PRODUCT NAME: ROHPER 1-GL 2PK V7400 HIGH GLOSS WHITE
IDENTIFICATION NUMBER: 245406
PRODUCT USE/CLASS: TOPCOAT/ALKYD
SUPPLIER:
RUST-OLEUM CORPORATION
11 HAWTHORN PARKWAY
VERNON HILLS, IL 60061
USA
MANUFACTURER:
RUST-OLEUM CORPORATION
11 HAWTHORN PARKWAY
VERNON HILLS, IL 60061
USA
PREPARER: REGULATORY DEPARTMENT
REVISION DATE: 04/19/2011
| SECTION 2 - COMPOSITION / INFORMATION ON INGREDIENTS | |
CHEMICAL NAME CAS NUMBER WEIGHT ACGIH ACGIH OSHA OSHA PEL
% LESS TLV-TWA TLV-STEL PEL-TWA CEILING
THAN
MINERAL 64742-88-7 25.0 100 PPM N.E. 100 PPM N.E.
SPIRITS
TITANIUM 13463-67-7 20.0 10 MG/M3 N.E. 15 MG/M3 N.E.
DIOXIDE (TOTAL
DUST)
1-CHLORO-4 98-56-6 20.0 N.E. N.E. N.E. N.E.
(TRIFLUORO-
METHYL)
BENZENE
OCTAMETHYL- 556-67-2 5.0 N.E. N.E. N.E. N.E.
CYCLOTETRA-
SILOXANE
ETHYLBENZENE 100-41-4 1.0 100 PPM 125 PPM 100 PPM N.E.
| SECTION 3 - HAZARDS IDENTIFICATION | |
EMERGENCY OVERVIEW:
HIGH VAPOR CONCENTRATIONS CAN IRRITATE EYES, NOSE AND RESPIRATORY
PASSAGES. CAUSES NOSE AND THROAT IRRITATION. HARMFUL IF INHALED. MAY
AFFECT THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA.
HARMFUL IF SWALLOWED. CAUSES EYE IRRITATION. FLAMMABLE LIQUID AND VAPOR.
EFFECTS OF OVEREXPOSURE - EYE CONTACT: CAUSES EYE IRRITATION.
EFFECTS OF OVEREXPOSURE - SKIN CONTACT:
PROLONGED OR REPEATED SKIN CONTACT MAY CAUSE IRRITATION.
EFFECTS OF OVEREXPOSURE - INHALATION:
HIGH VAPOR CONCENTRATIONS ARE IRRITATING TO THE EYES, NOSE, THROAT AND
LUNGS. MAY CAUSE HEADACHES AND DIZZINESS. AVOID BREATHING VAPORS OR MISTS.
HARMFUL IF INHALED.
EFFECTS OF OVEREXPOSURE - INGESTION:
ASPIRATION HAZARD IF SWALLOWED; CAN ENTER LUNGS AND CAUSE DAMAGE. HARMFUL
IF SWALLOWED.
EFFECTS OF OVEREXPOSURE - CHRONIC HAZARDS:
CONTAINS TITANIUM DIOXIDE. TITANIUM DIOXIDE IS LISTED AS A GROUP
2B-"POSSIBLY CARCINOGENIC TO HUMANS" BY IARC. SIGNIFICANT EXPOSURE IS NOT
ANTICIPATED DURING BRUSH APPLICATION OR DRYING. RISK OF OVEREXPOSURE
DEPENDS ON DURATION AND LEVEL OF EXPOSURE TO DUST FROM REPEATED SANDING OF
SURFACES OR SPRAY MIST AND THE ACTUAL CONCENTRATION OF TITANIUM DIOXIDE IN
THE FORMULA.
REPORTS HAVE ASSOCIATED REPEATED AND PROLONGED OCCUPATIONAL OVEREXPOSURE
TO SOLVENTS WITH PERMANENT BRAIN AND NERVOUS SYSTEM DAMAGE.
PRIMARY ROUTE(S) OF ENTRY:
SKIN CONTACT, SKIN ABSORPTION, INHALATION, INGESTION, EYE CONTACT
| SECTION 4 - FIRST AID MEASURES | |
FIRST AID - EYE CONTACT:
IMMEDIATELY FLUSH EYES WITH PLENTY OF WATER FOR AT LEAST 15 MINUTES
HOLDING EYELIDS OPEN. GET MEDICAL ATTENTION. DO NOT ALLOW RUBBING OF EYES
OR KEEPING EYES CLOSED.
FIRST AID - SKIN CONTACT:
WASH WITH SOAP AND WATER. GET MEDICAL ATTENTION IF IRRITATION DEVELOPS OR
PERSISTS.
FIRST AID - INHALATION:
REMOVE TO FRESH AIR. IF NOT BREATHING, GIVE ARTIFICIAL RESPIRATION. IF
BREATHING IS DIFFICULT, GIVE OXYGEN. GET IMMEDIATE MEDICAL ATTENTION. DO
NOT USE MOUTH-TO-MOUTH RESUSCITATION.
FIRST AID - INGESTION:
ASPIRATION HAZARD:
DO NOT INDUCE VOMITING OR GIVE ANYTHING BY MOUTH BECAUSE THIS MATERIAL CAN
ENTER THE LUNGS AND CAUSE SEVERE LUNG DAMAGE. GET IMMEDIATE MEDICAL
ATTENTION.
| SECTION 5 - FIRE FIGHTING MEASURES | |
FLASH POINT: 98 F (SETAFLASH)
EXTINGUISHING MEDIA:
FILM FORMING FOAM, CARBON DIOXIDE, DRY CHEMICAL, WATER FOG
UNUSUAL FIRE AND EXPLOSION HAZARDS:
ISOLATE FROM HEAT, ELECTRICAL EQUIPMENT, SPARKS AND OPEN FLAME. VAPORS MAY
FORM EXPLOSIVE MIXTURES WITH AIR. VAPORS CAN TRAVEL TO A SOURCE OF
IGNITION AND FLASH BACK.
SPECIAL FIREFIGHTING PROCEDURES:
EVACUATE AREA AND FIGHT FIRE FROM A SAFE DISTANCE. WATER MAY BE USED TO
COOL CLOSED CONTAINERS TO PREVENT PRESSURE BUILDUP AND POSSIBLE
AUTOIGNITION OR EXPLOSION.
| SECTION 6 - ACCIDENTAL RELEASE MEASURES | |
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED:
ELIMINATE ALL IGNITION SOURCES; USE EXPLOSION-PROOF EQUIPMENT. PLACE
MATERIAL IN A CONTAINER AND DISPOSE OF ACCORDING TO LOCAL, PROVINCIAL,
STATE AND FEDERAL REGULATIONS. CONTAIN SPILLED LIQUID WITH SAND OR EARTH.
DO NOT USE COMBUSTIBLE MATERIALS SUCH AS SAWDUST.
| SECTION 7 - HANDLING AND STORAGE | |
HANDLING:
FOLLOW ALL MSDS/LABEL PRECAUTIONS EVEN AFTER CONTAINER IS EMPTIED BECAUSE
IT MAY RETAIN PRODUCT RESIDUES. USE WITH ADEQUATE VENTILATION. WASH
THOROUGHLY AFTER HANDLING. WASH HANDS BEFORE EATING.
STORAGE:
KEEP CONTAINER CLOSED WHEN NOT IN USE. KEEP AWAY FROM HEAT, SPARKS, FLAME
AND SOURCES OF IGNITION. KEEP CONTAINERS TIGHTLY CLOSED. ISOLATE FROM
HEAT, ELECTRICAL EQUIPMENT, SPARKS AND OPEN FLAME.
| SECTION 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION | |
ENGINEERING CONTROLS:
PREVENT BUILD-UP OF VAPORS BY OPENING ALL DOORS AND WINDOWS TO ACHIEVE
CROSS-VENTILATION. USE PROCESS ENCLOSURES, LOCAL EXHAUST VENTILATION, OR
OTHER ENGINEERING CONTROLS TO CONTROL AIRBORNE LEVELS BELOW RECOMMENDED
EXPOSURE LIMITS.
RESPIRATORY PROTECTION:
A NIOSH/MSHA APPROVED AIR PURIFYING RESPIRATOR WITH AN ORGANIC VAPOR
CARTRIDGE OR CANISTER MAY BE PERMISSIBLE UNDER CERTAIN CIRCUMSTANCES WHERE
AIRBORNE CONCENTRATIONS ARE EXPECTED TO EXCEED EXPOSURE LIMITS.
PROTECTION PROVIDED BY AIR PURIFYING RESPIRATORS IS LIMITED. USE A
POSITIVE PRESSURE AIR SUPPLIED RESPIRATOR IF THERE IS ANY POTENTIAL FOR AN
UNCONTROLLED RELEASE, EXPOSURE LEVELS ARE NOT KNOWN, OR IN ANY OTHER
CIRCUMSTANCES WHERE AIR PURIFYING RESPIRATORS MAY NOT PROVIDE ADEQUATE
PROTECTION. A RESPIRATORY PROTECTION PROGRAM THAT MEETS OSHA 1910.134 AND
ANSI Z88.2 REQUIREMENTS MUST BE FOLLOWED WHENEVER WORKPLACE CONDITIONS
WARRANT A RESPIRATOR'S USE.
SKIN PROTECTION:
NITRILE OR NEOPRENE GLOVES MAY AFFORD ADEQUATE SKIN PROTECTION. USE
IMPERVIOUS GLOVES TO PREVENT SKIN CONTACT AND ABSORPTION OF THIS MATERIAL
THROUGH THE SKIN.
EYE PROTECTION:
USE SAFETY EYEWEAR DESIGNED TO PROTECT AGAINST SPLASH OF LIQUIDS.
OTHER PROTECTIVE EQUIPMENT:
REFER TO SAFETY SUPERVISOR OR INDUSTRIAL HYGIENIST FOR FURTHER INFORMATION
REGARDING PERSONAL PROTECTIVE EQUIPMENT AND ITS APPLICATION.
HYGIENIC PRACTICES:
WASH THOROUGHLY WITH SOAP AND WATER BEFORE EATING, DRINKING OR SMOKING.
| SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES | |
VAPOR DENSITY: HEAVIER THAN AIR
APPEARANCE: LIQUID
SOLUBILITY IN H2O: SLIGHT
SPECIFIC GRAVITY: 1.171
PHYSICAL STATE: LIQUID
ODOR: SOLVENT LIKE
EVAPORATION RATE: SLOWER THAN ETHER
FREEZE POINT: N.D.
pH: N.A.
(SEE SECTION 16 FOR ABBREVIATION LEGEND)
| SECTION 10 - STABILITY AND REACTIVITY | |
CONDITIONS TO AVOID: AVOID ALL POSSIBLE SOURCES OF IGNITION.
INCOMPATIBILITY:
INCOMPATIBLE WITH STRONG OXIDIZING AGENTS, STRONG ACIDS AND STRONG
ALKALIES.
HAZARDOUS DECOMPOSITION:
WHEN HEATED TO DECOMPOSITION, IT EMITS ACRID SMOKE AND IRRITATING FUMES.
BY OPEN FLAME, CARBON MONOXIDE AND CARBON DIOXIDE.
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR UNDER NORMAL CONDITIONS.
STABILITY: THIS PRODUCT IS STABLE UNDER NORMAL STORAGE CONDITIONS.
| SECTION 11 - TOXICOLOGICAL INFORMATION | |
CHEMICAL NAME LD50 LC50
MINERAL SPIRITS >5000 MG/KG >1400 PPM (RAT,
(RAT, ORAL) INHALATION, 4HR)
TITANIUM DIOXIDE >7500 MG/KG N.E.
(RAT, ORAL)
1-CHLORO-4(TRIFLUOROMETHYL) 4479 PPM 6800 MG/KG
BENZENE (RAT, INHALATION) (RAT, ORAL)
OCTAMETHYLCYCLOTETRASILOXANE 1540 MG/KG N.E.
(RAT, ORAL)
ETHYLBENZENE 3500 MG/KG N.E.
(RAT, ORAL)
| SECTION 12 - ECOLOGICAL INFORMATION | |
ECOLOGICAL INFORMATION: PRODUCT IS A MIXTURE OF LISTED COMPONENTS.
| SECTION 13 - DISPOSAL INFORMATION | |
DISPOSAL INFORMATION:
DISPOSE OF MATERIAL IN ACCORDANCE TO LOCAL, STATE AND FEDERAL REGULATIONS
AND ORDINANCES. DO NOT ALLOW TO ENTER STORM DRAINS OR SEWER SYSTEMS.
| SECTION 14 - TRANSPORTATION INFORMATION | |
DOMESTIC INTERNATIONAL (IMDG) AIR (IATA)
(USDOT)
PROPER SHIPPING NAME CONSUMER PAINT PAINT
COMMODITY
HAZARD CLASS ORM-D 3 3
UN NUMBER N.A. UN1263 UN1263
PACKING GROUP N.A. III III
LIMITED QUANTITY NO IMDG 34-08, 3.4.7 YES
| SECTION 15 - REGULATORY INFORMATION | |
CERCLA - SARA HAZARD CATEGORY:
THIS PRODUCT HAS BEEN REVIEWED ACCORDING TO THE EPA "HAZARD CATEGORIES"
PROMULGATED UNDER SECTIONS 311 AND 312 OF THE SUPERFUND AMENDMENT AND
REAUTHORIZATION ACT OF 1986 (SARA TITLE III) AND IS CONSIDERED, UNDER
APPLICABLE DEFINITIONS, TO MEET THE FOLLOWING CATEGORIES:
IMMEDIATE HEALTH HAZARD, CHRONIC HEALTH HAZARD, FIRE HAZARD
SARA SECTION 313:
LISTED BELOW ARE THE SUBSTANCES (IF ANY) CONTAINED IN THIS PRODUCT THAT
ARE SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313 OF TITLE III OF
THE SUPERFUND AMENDMENT AND REAUTHORIZATION ACT OF 1986 AND 40 CFR PART
372:
CHEMICAL NAME CAS NUMBER
1-CHLORO-4(TRIFLUOROMETHYL)BENZENE 98-56-6
TOXIC SUBSTANCES CONTROL ACT:
LISTED BELOW ARE THE SUBSTANCES (IF ANY) CONTAINED IN THIS PRODUCT THAT
ARE SUBJECT TO THE REPORTING REQUIREMENTS OF TSCA 12(B) IF EXPORTED FROM
THE UNITED STATES:
U.S. STATE REGULATIONS: AS FOLLOWS
NEW JERSEY RIGHT-TO-KNOW:
THE FOLLOWING MATERIALS ARE NON-HAZARDOUS, BUT ARE AMONG THE TOP FIVE
COMPONENTS IN THIS PRODUCT.
CHEMICAL NAME CAS NUMBER
ALKYD RESIN PROPRIETARY
ALKYD POLYMER PROPRIETARY
PENNSYLVANIA RIGHT-TO-KNOW:
THE FOLLOWING NON-HAZARDOUS INGREDIENTS ARE PRESENT IN THE PRODUCT AT
GREATER THAN 3%.
CHEMICAL NAME CAS NUMBER
ALKYD RESIN PROPRIETARY
ALKYD POLYMER PROPRIETARY
INTERNATIONAL REGULATIONS: AS FOLLOWS
CANADIAN WHMIS:
THIS MSDS HAS BEEN PREPARED IN COMPLIANCE WITH CONTROLLED PRODUCT
REGULATIONS EXCEPT FOR THE USE OF THE 16 HEADINGS.
CANADIAN WHMIS CLASS:
B2
D2A
D2B
| SECTION 16 - OTHER INFORMATION | |
NFPA RATINGS:
HEALTH 2
FLAMMABILITY 3
INSTABILITY 0
VOLATILE ORGANIC COMPOUNDS, G/L: 337
REASON FOR REVISION: REGULATORY UPDATE
LEGEND:
N.A. - NOT APPLICABLE
N.E. - NOT ESTABLISHED
N.D. - NOT DETERMINED
RUST-OLEUM CORPORATION BELIEVES, TO THE BEST OF ITS KNOWLEDGE, INFORMATION
AND BELIEF, THE INFORMATION CONTAINED HEREIN TO BE ACCURATE AND RELIABLE
AS OF THE DATE OF THIS MATERIAL SAFETY DATA SHEET. HOWEVER, BECAUSE THE
CONDITIONS OF HANDLING, USE, AND STORAGE OF THESE MATERIALS ARE BEYOND OUR
CONTROL, WE ASSUME NO RESPONSIBILITY OR LIABILITY FOR PERSONAL INJURY OR
PROPERTY DAMAGE INCURRED BY THE USE OF THESE MATERIALS. RUST-OLEUM
CORPORATION MAKES NO WARRANTY, EXPRESSED OR IMPLIED, REGARDING THE
ACCURACY OR RELIABILITY OF THE DATA OR RESULTS OBTAINED FROM THEIR USE.
ALL MATERIALS MAY PRESENT UNKNOWN HAZARDS AND SHOULD BE USED WITH CAUTION.
THE INFORMATION AND RECOMMENDATIONS IN THIS MATERIAL SAFETY DATA SHEET ARE
OFFERED FOR THE USERS' CONSIDERATION AND EXAMINATION. IT IS THE
RESPONSIBILITY OF THE USER TO DETERMINE THE FINAL SUITABILITY OF THIS
INFORMATION AND TO COMPLY WITH ALL APPLICABLE INTERNATIONAL, FEDERAL,
STATE, AND LOCAL LAWS AND REGULATIONS.