| Common Name: | STRUST SSPR 6PK TEXTUR NICKEL, 7224830 |
| Manufacturer: | RUST-OLEUM |
| SDS Revision Date: | 3/3/2010 |
| SDS Format: | No Format Specified |
| Item Number(s): | 2CEE1 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
MATERIAL SAFETY DATA SHEET
24 HOUR ASSISTANCE:
1-847-367-7700
RUST-OLEUM CORP.
WWW.RUSTOLEUM.COM
| SECTION 1 - CHEMICAL PRODUCT / COMPANY INFORMATION |  |
PRODUCT NAME: STRUST SSPR 6PK TEXTUR NICKEL
IDENTIFICATION NUMBER: 7224830
PRODUCT USE/CLASS:
SUPPLIER:
RUST-OLEUM CORPORATION
11 HAWTHORN PARKWAY
VERNON HILLS, IL 60061
USA
MANUFACTURER:
RUST-OLEUM CORPORATION
11 HAWTHORN PARKWAY
VERNON HILLS, IL 60061
USA
PREPARER: REGULATORY DEPARTMENT
REVISION DATE: 03/03/2010
| SECTION 2 - COMPOSITION / INFORMATION ON INGREDIENTS | |
CHEMICAL NAME CAS NUMBER WEIGHT % LESS THAN
ACETONE 67-64-1 30.0
LIQUEFIED PETROLEUM GAS 68476-86-8 30.0
ALKYD RESIN PROPRIETARY 20.0
n-BUTYL ACETATE 123-86-4 10.0
XYLENE 1330-20-7 10.0
METHYL ETHYL KETONE 78-93-3 5.0
ALUMINUM FLAKE 7429-90-5 5.0
POLYPROPYLENE 9003-07-0 5.0
PROPYLENE GLYCOL MONOBUTYL ETHER 5131-66-8 5.0
ETHYLBENZENE 100-41-4 5.0
CHEMICAL NAME ACGIH ACGIH OSHA OSHA PEL
TLV-TWA TLV-STEL PEL-TWA CEILING
ACETONE 500 PPM 750 PPM 1000 PPM N.E.
LIQUEFIED PETROLEUM N.E. N.E. N.E. N.E.
GAS
ALKYD RESIN N.E. N.E. N.E. N.E.
n-BUTYL ACETATE 150 PPM 200 PPM 150 PPM N.E.
XYLENE 100 PPM 150 PPM 100 PPM N.E.
METHYL ETHYL KETONE 200 PPM 300 PPM 200 PPM N.E.
ALUMINUM FLAKE 1 MG/M3 N.E. 5 MG/M3 (RESPIRABLE) N.E.
POLYPROPYLENE N.E. N.E. 5 MG/M3 N.E.
PROPYLENE GLYCOL N.E. N.E. N.E. N.E.
MONOBUTYL ETHER
ETHYLBENZENE 100 PPM 125 PPM 100 PPM N.E.
| SECTION 3 - HAZARDS IDENTIFICATION | |
EMERGENCY OVERVIEW:
CONTENTS UNDER PRESSURE. HARMFUL IF INHALED. MAY AFFECT THE BRAIN OR
NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA. VAPORS MAY CAUSE
FLASH FIRE OR EXPLOSION. HARMFUL IF SWALLOWED. EXTREMELY FLAMMABLE LIQUID
AND VAPOR.
EFFECTS OF OVEREXPOSURE - EYE CONTACT: CAUSES EYE IRRITATION.
EFFECTS OF OVEREXPOSURE - SKIN CONTACT:
PROLONGED OR REPEATED CONTACT MAY CAUSE SKIN IRRITATION. SUBSTANCE MAY
CAUSE SLIGHT SKIN IRRITATION.
EFFECTS OF OVEREXPOSURE - INHALATION:
HIGH VAPOR CONCENTRATIONS ARE IRRITATING TO THE EYES, NOSE, THROAT AND
LUNGS. AVOID BREATHING VAPORS OR MISTS. HIGH GAS, VAPOR, MIST OR DUST
CONCENTRATIONS MAY BE HARMFUL IF INHALED. HARMFUL IF INHALED.
EFFECTS OF OVEREXPOSURE - INGESTION:
ASPIRATION HAZARD IF SWALLOWED; CAN ENTER LUNGS AND CAUSE DAMAGE.
SUBSTANCE MAY BE HARMFUL IF SWALLOWED.
EFFECTS OF OVEREXPOSURE - CHRONIC HAZARDS:
IARC LISTS ETHYLBENZENE AS A POSSIBLE HUMAN CARCINOGEN (GROUP 2B). MAY
CAUSE CENTRAL NERVOUS SYSTEM DISORDER (E.G., NARCOSIS INVOLVING A LOSS OF
COORDINATION, WEAKNESS, FATIGUE, MENTAL CONFUSION, AND BLURRED VISION)
AND/OR DAMAGE. REPORTS HAVE ASSOCIATED REPEATED AND PROLONGED OCCUPATIONAL
OVEREXPOSURE TO SOLVENTS WITH PERMANENT BRAIN AND NERVOUS SYSTEM DAMAGE.
OVEREXPOSURE TO XYLENE IN LABORATORY ANIMALS HAS BEEN ASSOCIATED WITH LIVER
ABNORMALITIES, KIDNEY, LUNG, SPLEEN, EYE AND BLOOD DAMAGE AS WELL AS
REPRODUCTIVE DISORDERS. EFFECTS IN HUMANS, DUE TO CHRONIC OVEREXPOSURE,
HAVE INCLUDED LIVER, CARDIAC ABNORMALITIES AND NERVOUS SYSTEM DAMAGE.
OVEREXPOSURE TO METHYL ETHYL KETONE IN LABORATORY ANIMALS HAS BEEN
ASSOCIATED WITH LIVER ABNORMALITIES, KIDNEY AND LUNG DAMAGE.
FETOTOXIC/EMBRYOTOXIC EFFECTS FROM INHALATION HAVE BEEN SEEN IN RATS
EXPOSED TO >1000 PPM DURING GESTATION.
PRIMARY ROUTE(S) OF ENTRY:
SKIN CONTACT, SKIN ABSORPTION, INHALATION, INGESTION, EYE CONTACT
| SECTION 4 - FIRST AID MEASURES | |
FIRST AID - EYE CONTACT:
IMMEDIATELY FLUSH EYES WITH PLENTY OF WATER FOR AT LEAST 15 MINUTES HOLDING
EYELIDS OPEN. GET MEDICAL ATTENTION. DO NOT ALLOW RUBBING OF EYES OR
KEEPING EYES CLOSED.
FIRST AID - SKIN CONTACT:
WASH WITH SOAP AND WATER. GET MEDICAL ATTENTION IF IRRITATION DEVELOPS OR
PERSISTS.
FIRST AID - INHALATION:
IF YOU EXPERIENCE DIFFICULTY IN BREATHING, LEAVE THE AREA TO OBTAIN FRESH
AIR. IF CONTINUED DIFFICULTY IS EXPERIENCED, GET MEDICAL ASSISTANCE
IMMEDIATELY.
FIRST AID - INGESTION:
ASPIRATION HAZARD:
DO NOT INDUCE VOMITING OR GIVE ANYTHING BY MOUTH BECAUSE THIS MATERIAL CAN
ENTER THE LUNGS AND CAUSE SEVERE LUNG DAMAGE. GET IMMEDIATE MEDICAL
ATTENTION.
| SECTION 5 - FIRE FIGHTING MEASURES | |
FLASH POINT: -156 F (SETAFLASH)
LOWER EXPLOSIVE LIMIT: 0.7%
UPPER EXPLOSIVE LIMIT: 12.8%
EXTINGUISHING MEDIA:
FILM FORMING FOAM, CARBON DIOXIDE, DRY CHEMICAL, WATER FOG
UNUSUAL FIRE AND EXPLOSION HAZARDS:
WATER SPRAY MAY BE INEFFECTIVE. CLOSED CONTAINERS MAY EXPLODE WHEN EXPOSED
TO EXTREME HEAT. VAPORS MAY FORM EXPLOSIVE MIXTURES WITH AIR. VAPORS CAN
TRAVEL TO A SOURCE OF IGNITION AND FLASH BACK. FLASH POINT IS LESS THAN 20
DEG. F. -EXTREMELY FLAMMABLE LIQUID AND VAPOR!
KEEP CONTAINERS TIGHTLY CLOSED. ISOLATE FROM HEAT, ELECTRICAL EQUIPMENT,
SPARKS AND OPEN FLAME. PERFORATION OF THE PRESSURIZED CONTAINER MAY CAUSE
BURSTING OF THE CAN.
SPECIAL FIREFIGHTING PROCEDURES:
EVACUATE AREA AND FIGHT FIRE FROM A SAFE DISTANCE.
| SECTION 6 - ACCIDENTAL RELEASE MEASURES | |
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED:
CONTAIN SPILLED LIQUID WITH SAND OR EARTH. DO NOT USE COMBUSTIBLE MATERIALS
SUCH AS SAWDUST. DISPOSE OF ACCORDING TO LOCAL, STATE (PROVINCIAL) AND
FEDERAL REGULATIONS. DO NOT INCINERATE CLOSED CONTAINERS. REMOVE ALL
SOURCES OF IGNITION, VENTILATE AREA AND REMOVE WITH INERT ABSORBENT AND
NON-SPARKING TOOLS.
| SECTION 7 - HANDLING AND STORAGE | |
HANDLING:
WASH THOROUGHLY AFTER HANDLING. FOLLOW ALL MSDS/LABEL PRECAUTIONS EVEN
AFTER CONTAINER IS EMPTIED BECAUSE IT MAY RETAIN PRODUCT RESIDUES. AVOID
BREATHING VAPOR OR MIST. USE ONLY IN A WELL-VENTILATED AREA. WASH HANDS
BEFORE EATING.
STORAGE:
KEEP CONTAINERS TIGHTLY CLOSED. ISOLATE FROM HEAT, ELECTRICAL EQUIPMENT,
SPARKS AND OPEN FLAME. DO NOT STORE ABOVE 120 DEG. F. STORE LARGE
QUANTITIES IN BUILDINGS DESIGNED AND PROTECTED FOR STORAGE OF NFPA CLASS I
FLAMMABLE LIQUIDS. CONTENTS UNDER PRESSURE. DO NOT EXPOSE TO HEAT OR STORE
ABOVE 120 DEG. F.
| SECTION 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION | |
ENGINEERING CONTROLS:
PREVENT BUILD-UP OF VAPORS BY OPENING ALL DOORS AND WINDOWS TO ACHIEVE
CROSS-VENTILATION. USE PROCESS ENCLOSURES, LOCAL EXHAUST VENTILATION, OR
OTHER ENGINEERING CONTROLS TO CONTROL AIRBORNE LEVELS BELOW RECOMMENDED
EXPOSURE LIMITS. USE EXPLOSION-PROOF VENTILATION EQUIPMENT.
RESPIRATORY PROTECTION:
A RESPIRATORY PROTECTION PROGRAM THAT MEETS OSHA 1910.134 AND ANSI Z88.2
REQUIREMENTS MUST BE FOLLOWED WHENEVER WORKPLACE CONDITIONS WARRANT A
RESPIRATOR'S USE. A NIOSH/MSHA APPROVED AIR PURIFYING RESPIRATOR WITH AN
ORGANIC VAPOR CARTRIDGE OR CANISTER MAY BE PERMISSIBLE UNDER CERTAIN
CIRCUMSTANCES WHERE AIRBORNE CONCENTRATIONS ARE EXPECTED TO EXCEED EXPOSURE
LIMITS.
PROTECTION PROVIDED BY AIR PURIFYING RESPIRATORS IS LIMITED. USE A POSITIVE
PRESSURE AIR SUPPLIED RESPIRATOR IF THERE IS ANY POTENTIAL FOR AN
UNCONTROLLED RELEASE, EXPOSURE LEVELS ARE NOT KNOWN, OR IN ANY OTHER
CIRCUMSTANCES WHERE AIR PURIFYING RESPIRATORS MAY NOT PROVIDE ADEQUATE
PROTECTION.
SKIN PROTECTION:
USE IMPERVIOUS GLOVES TO PREVENT SKIN CONTACT AND ABSORPTION OF THIS
MATERIAL THROUGH THE SKIN. NITRILE OR NEOPRENE GLOVES MAY AFFORD ADEQUATE
SKIN PROTECTION.
EYE PROTECTION:
USE SAFETY EYEWEAR DESIGNED TO PROTECT AGAINST SPLASH OF LIQUIDS.
OTHER PROTECTIVE EQUIPMENT:
REFER TO SAFETY SUPERVISOR OR INDUSTRIAL HYGIENIST FOR FURTHER INFORMATION
REGARDING PERSONAL PROTECTIVE EQUIPMENT AND ITS APPLICATION.
HYGIENIC PRACTICES:
WASH THOROUGHLY WITH SOAP AND WATER BEFORE EATING, DRINKING OR SMOKING.
| SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES | |
BOILING RANGE: -34 - 399 F
ODOR: SOLVENT LIKE
APPEARANCE: LIQUID
SOLUBILITY IN H2O: SLIGHT
FREEZE POINT: ND
VAPOR PRESSURE: ND
VAPOR DENSITY: HEAVIER THAN AIR
ODOR THRESHOLD: ND
EVAPORATION RATE: FASTER THAN ETHER
SPECIFIC GRAVITY: 0.770
pH: NE
PHYSICAL STATE: LIQUID
(SEE SECTION 16 FOR ABBREVIATION LEGEND)
| SECTION 10 - STABILITY AND REACTIVITY | |
CONDITIONS TO AVOID:
AVOID TEMPERATURES ABOVE 120 DEG. F. AVOID ALL POSSIBLE SOURCES OF
IGNITION. FLAMMABLE HYDROGEN GAS WILL EVOLVE WHEN PRODUCT COMES IN CONTACT
WITH WATER OR DAMP AIR. HEAT WILL BE GENERATED. THE AMOUNT OF HEAT
GENERATED WILL DEPEND UPON THE VOLUME OF MATERIAL IN CONTACT.
INCOMPATIBILITY:
INCOMPATIBLE WITH STRONG OXIDIZING AGENTS, STRONG ACIDS AND STRONG ALKALIS.
HAZARDOUS DECOMPOSITION:
WHEN HEATED TO DECOMPOSITION, IT EMITS ACRID SMOKE AND IRRITATING FUMES. BY
OPEN FLAME, CARBON MONOXIDE AND CARBON DIOXIDE.
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR UNDER NORMAL CONDITIONS.
STABILITY: THIS PRODUCT IS STABLE UNDER NORMAL STORAGE CONDITIONS.
| SECTION 11 - TOXICOLOGICAL INFORMATION | |
PRODUCT LD50: ND
PRODUCT LC50: ND
CHEMICAL NAME LD50 LC50
ACETONE 5800 MG/KG (RAT) 50100 MG/M3 (RAT, 8HR)
LIQUEFIED PETROLEUM N.E. N.E.
GAS
ALKYD RESIN N.E. N.E.
n-BUTYL ACETATE 13100 MG/KG (RAT, ORAL) 2000 PPM
(RAT, INHALATION, 4 HR)
XYLENE 4300 MG/KG (RAT, ORAL) 5000 PPM
(RAT, INHALATION, 4HR)
METHYL ETHYL KETONE N.E. N.E.
ALUMINUM FLAKE N.E. N.E.
POLYPROPYLENE N.E. N.E.
PROPYLENE GLYCOL 2200 MG/KG (RAT, ORAL) N.E.
MONOBUTYL ETHER
ETHYLBENZENE 3500 MG/KG (RAT, ORAL) N.E.
| SECTION 12 - ECOLOGICAL INFORMATION | |
ECOLOGICAL INFORMATION: PRODUCT IS A MIXTURE OF LISTED COMPONENTS.
| SECTION 13 - DISPOSAL INFORMATION | |
DISPOSAL INFORMATION:
DISPOSE OF MATERIAL IN ACCORDANCE TO LOCAL, STATE AND FEDERAL REGULATIONS
AND ORDINANCES. DO NOT ALLOW TO ENTER STORM DRAINS OR SEWER SYSTEMS.
| SECTION 14 - TRANSPORTATION INFORMATION | |
DOT PROPER SHIPPING NAME: AEROSOLS
DOT TECHNICAL NAME: N.A.
DOT HAZARD CLASS: 2.1
DOT UN/NA NUMBER: UN1950
PACKING GROUP: N.A.
HAZARD SUBCLASS: N.A.
RESP. GUIDE PAGE: 126
| SECTION 15 - REGULATORY INFORMATION | |
CERCLA - SARA HAZARD CATEGORY:
THIS PRODUCT HAS BEEN REVIEWED ACCORDING TO THE EPA "HAZARD CATEGORIES"
PROMULGATED UNDER SECTIONS 311 AND 312 OF THE SUPERFUND AMENDMENT AND
REAUTHORIZATION ACT OF 1986 (SARA TITLE III) AND IS CONSIDERED, UNDER
APPLICABLE DEFINITIONS, TO MEET THE FOLLOWING CATEGORIES:
IMMEDIATE HEALTH HAZARD
CHRONIC HEALTH HAZARD
FIRE HAZARD
PRESSURIZED GAS HAZARD
SARA SECTION 313:
LISTED BELOW ARE THE SUBSTANCES (IF ANY) CONTAINED IN THIS PRODUCT THAT ARE
SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313 OF TITLE III OF THE
SUPERFUND AMENDMENT AND REAUTHORIZATION ACT OF 1986 AND 40 CFR PART 372:
CHEMICAL NAME CAS NUMBER
XYLENE 1330-20-7
METHYL ETHYL KETONE 78-93-3
ALUMINUM FLAKE 7429-90-5
ETHYLBENZENE 100-41-4
TOXIC SUBSTANCES CONTROL ACT:
LISTED BELOW ARE THE SUBSTANCES (IF ANY) CONTAINED IN THIS PRODUCT THAT ARE
SUBJECT TO THE REPORTING REQUIREMENTS OF TSCA 12(B) IF EXPORTED FROM THE
UNITED STATES:
U.S. STATE REGULATIONS: AS FOLLOWS
NEW JERSEY RIGHT-TO-KNOW:
THE FOLLOWING MATERIALS ARE NON-HAZARDOUS, BUT ARE AMONG THE TOP FIVE
COMPONENTS IN THIS PRODUCT.
NONE
PENNSYLVANIA RIGHT-TO-KNOW:
THE FOLLOWING NON-HAZARDOUS INGREDIENTS ARE PRESENT IN THE PRODUCT AT
GREATER THAN 3%.
NONE
CALIFORNIA PROPOSITION 65:
WARNING!
THIS PRODUCT CONTAINS A CHEMICAL(S) KNOWN BY THE STATE OF
CALIFORNIA TO CAUSE CANCER.
WARNING!
THIS PRODUCT CONTAINS A CHEMICAL(S) KNOWN TO THE STATE OF
CALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
INTERNATIONAL REGULATIONS: AS FOLLOWS
CANADIAN WHMIS:
THIS MSDS HAS BEEN PREPARED IN COMPLIANCE WITH CONTROLLED PRODUCT
REGULATIONS EXCEPT FOR THE USE OF THE 16 HEADINGS.
CANADIAN WHMIS CLASS:
AB5
D2A
D2B
| SECTION 16 - OTHER INFORMATION | |
HMIS RATINGS:
HEALTH 2
FLAMMABILITY 4
INSTABILITY 0
REASON FOR REVISION: REGULATORY UPDATE
LEGEND:
N.A.: NOT APPLICABLE
N.E.: NOT ESTABLISHED
N.D.: NOT DETERMINED
RUST-OLEUM CORPORATION BELIEVES, TO THE BEST OF ITS KNOWLEDGE, INFORMATION
AND BELIEF, THE INFORMATION CONTAINED HEREIN TO BE ACCURATE AND RELIABLE AS
OF THE DATE OF THIS MATERIAL SAFETY DATA SHEET. HOWEVER, BECAUSE THE
CONDITIONS OF HANDLING, USE, AND STORAGE OF THESE MATERIALS ARE BEYOND OUR
CONTROL, WE ASSUME NO RESPONSIBILITY OR LIABILITY FOR PERSONAL INJURY OR
PROPERTY DAMAGE INCURRED BY THE USE OF THESE MATERIALS. RUST-OLEUM
CORPORATION MAKES NO WARRANTY, EXPRESSED OR IMPLIED, REGARDING THE ACCURACY
OR RELIABILITY OF THE DATA OR RESULTS OBTAINED FROM THEIR USE. ALL
MATERIALS MAY PRESENT UNKNOWN HAZARDS AND SHOULD BE USED WITH CAUTION. THE
INFORMATION AND RECOMMENDATIONS IN THIS MATERIAL SAFETY DATA SHEET ARE
OFFERED FOR THE USERS' CONSIDERATION AND EXAMINATION. IT IS THE
RESPONSIBILITY OF THE USER TO DETERMINE THE FINAL SUITABILITY OF THIS
INFORMATION AND TO COMPLY WITH ALL APPLICABLE INTERNATIONAL, FEDERAL,
STATE, AND LOCAL LAWS AND REGULATIONS.