| Common Name: | AERO HFA |
| Manufacturer: | EXXON MOBIL |
| SDS Revision Date: | 9/30/2011 |
| SDS Format: | No Format Specified |
| Item Number(s): | 4DNJ3 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
MATERIAL SAFETY DATA SHEET
EXXON MOBIL
PRODUCT NAME: MOBIL AERO HFA
REVISION DATE: 30 SEP 2011
| SECTION 1 PRODUCT AND COMPANY IDENTIFICATION |  |
PRODUCT:
PRODUCT NAME: MOBIL AERO HFA
PRODUCT DESCRIPTION: BASE OIL AND ADDITIVES
PRODUCT CODE: 201550401020, 490110-00, 970584
INTENDED USE: AVIATION HYDRAULIC OIL
COMPANY IDENTIFICATION:
SUPPLIER:
EXXON MOBIL CORPORATION
3225 GALLOWS RD.
FAIRFAX, VA. 22037
USA
24 HOUR HEALTH EMERGENCY: 609-737-4411
TRANSPORTATION EMERGENCY PHONE: 800-424-9300
EXXONMOBIL TRANSPORTATION NO.: 281-834-3296
PRODUCT TECHNICAL INFORMATION:
800-662-4525
800-947-9147
MSDS INTERNET ADDRESS:
HTTP://WWW.EXXON.COM
HTTP://WWW.MOBIL.COM
| SECTION 2 COMPOSITION / INFORMATION ON INGREDIENTS | |
REPORTABLE HAZARDOUS SUBSTANCE(S) OR COMPLEX SUBSTANCE(S)
NAME CAS # CONCENTRATION*
DISTILLATES (PETROLEUM), HYDROTREATED LIGHT 64742-47-8 10 - 30%
HYDROTREATED LIGHT NAPHTHENIC DISTILLATE 64742-53-6 60 - 70%
(PETROLEUM)
HYDROTREATED LIGHT PARAFFINIC DISTILLATES, 64742-55-8 30 - 40%
PETROLEUM
* ALL CONCENTRATIONS ARE PERCENT BY WEIGHT UNLESS MATERIAL IS A GAS. GAS
CONCENTRATIONS ARE IN PERCENT BY VOLUME.
| SECTION 3 HAZARDS IDENTIFICATION | |
THIS MATERIAL IS CONSIDERED TO BE HAZARDOUS ACCORDING TO REGULATORY
GUIDELINES (SEE (M)SDS SECTION 15).
POTENTIAL PHYSICAL / CHEMICAL EFFECTS:
COMBUSTIBLE. MATERIAL CAN RELEASE VAPORS THAT READILY FORM FLAMMABLE
MIXTURES. VAPOR ACCUMULATION COULD FLASH AND/OR EXPLODE IF IGNITED.
MATERIAL CAN ACCUMULATE STATIC CHARGES WHICH MAY CAUSE AN IGNITION.
POTENTIAL HEALTH EFFECTS:
IF SWALLOWED, MAY BE ASPIRATED AND CAUSE LUNG DAMAGE. FREQUENT OR PROLONGED
CONTACT MAY DEFAT AND DRY THE SKIN, LEADING TO DISCOMFORT AND DERMATITIS.
MAY BE IRRITATING TO THE EYES, NOSE, THROAT, AND LUNGS. HIGH-PRESSURE
INJECTION UNDER SKIN MAY CAUSE SERIOUS DAMAGE.
TARGET ORGANS: SKIN
NFPA HAZARD ID:
HEALTH 0
FLAMMABILITY 2
REACTIVITY 0
HMIS HAZARD ID:
HEALTH 0*
FLAMMABILITY 2
REACTIVITY 0
NOTE:
THIS MATERIAL SHOULD NOT BE USED FOR ANY OTHER PURPOSE THAN THE INTENDED
USE IN SECTION 1 WITHOUT EXPERT ADVICE. HEALTH STUDIES HAVE SHOWN THAT
CHEMICAL EXPOSURE MAY CAUSE POTENTIAL HUMAN HEALTH RISKS WHICH MAY VARY
FROM PERSON TO PERSON.
| SECTION 4 FIRST AID MEASURES | |
INHALATION:
REMOVE FROM FURTHER EXPOSURE. FOR THOSE PROVIDING ASSISTANCE, AVOID
EXPOSURE TO YOURSELF OR OTHERS. USE ADEQUATE RESPIRATORY PROTECTION. IF
RESPIRATORY IRRITATION, DIZZINESS, NAUSEA, OR UNCONSCIOUSNESS OCCURS, SEEK
IMMEDIATE MEDICAL ASSISTANCE. IF BREATHING HAS STOPPED, ASSIST VENTILATION
WITH A MECHANICAL DEVICE OR USE MOUTH-TO-MOUTH RESUSCITATION.
SKIN CONTACT:
WASH CONTACT AREAS WITH SOAP AND WATER. REMOVE CONTAMINATED CLOTHING.
LAUNDER CONTAMINATED CLOTHING BEFORE REUSE. IF PRODUCT IS INJECTED INTO OR
UNDER THE SKIN, OR INTO ANY PART OF THE BODY, REGARDLESS OF THE APPEARANCE
OF THE WOUND OR ITS SIZE, THE INDIVIDUAL SHOULD BE EVALUATED IMMEDIATELY BY
A PHYSICIAN AS A SURGICAL EMERGENCY. EVEN THOUGH INITIAL SYMPTOMS FROM HIGH
PRESSURE INJECTION MAY BE MINIMAL OR ABSENT, EARLY SURGICAL TREATMENT
WITHIN THE FIRST FEW HOURS MAY SIGNIFICANTLY REDUCE THE ULTIMATE EXTENT OF
INJURY.
EYE CONTACT:
FLUSH THOROUGHLY WITH WATER. IF IRRITATION OCCURS, GET MEDICAL ASSISTANCE.
INGESTION:
SEEK IMMEDIATE MEDICAL ATTENTION. DO NOT INDUCE VOMITING.
NOTE TO PHYSICIAN:
IF INGESTED, MATERIAL MAY BE ASPIRATED INTO THE LUNGS AND CAUSE CHEMICAL
PNEUMONITIS. TREAT APPROPRIATELY.
| SECTION 5 FIRE FIGHTING MEASURES | |
EXTINGUISHING MEDIA:
APPROPRIATE EXTINGUISHING MEDIA:
USE WATER FOG, FOAM, DRY CHEMICAL OR CARBON DIOXIDE (CO2) TO EXTINGUISH
FLAMES.
INAPPROPRIATE EXTINGUISHING MEDIA: STRAIGHT STREAMS OF WATER
FIRE FIGHTING:
FIRE FIGHTING INSTRUCTIONS:
EVACUATE AREA. PREVENT RUNOFF FROM FIRE CONTROL OR DILUTION FROM ENTERING
STREAMS, SEWERS, OR DRINKING WATER SUPPLY. FIREFIGHTERS SHOULD USE STANDARD
PROTECTIVE EQUIPMENT AND IN ENCLOSED SPACES, SELF-CONTAINED BREATHING
APPARATUS (SCBA). USE WATER SPRAY TO COOL FIRE EXPOSED SURFACES AND TO
PROTECT PERSONNEL.
UNUSUAL FIRE HAZARDS:
COMBUSTIBLE. PRESSURIZED MISTS MAY FORM A FLAMMABLE MIXTURE.
HAZARDOUS COMBUSTION PRODUCTS:
SMOKE, FUME, ALDEHYDES, SULFUR OXIDES, PHOSPHORUS OXIDES, INCOMPLETE
COMBUSTION PRODUCTS, OXIDES OF CARBON
FLAMMABILITY PROPERTIES:
FLASH POINT [METHOD]: >82 DEG. C (180 DEG. F) [ASTM D-93]
FLAMMABLE LIMITS (APPROXIMATE VOLUME % IN AIR):
LEL: 0.7
UEL: 7.0 [ESTIMATED]
AUTOIGNITION TEMPERATURE: >225 DEG. C (437 DEG. F)
| SECTION 6 ACCIDENTAL RELEASE MEASURES | |
NOTIFICATION PROCEDURES:
IN THE EVENT OF A SPILL OR ACCIDENTAL RELEASE, NOTIFY RELEVANT AUTHORITIES
IN ACCORDANCE WITH ALL APPLICABLE REGULATIONS. US REGULATIONS REQUIRE
REPORTING RELEASES OF THIS MATERIAL TO THE ENVIRONMENT WHICH EXCEED THE
APPLICABLE REPORTABLE QUANTITY OR OIL SPILLS WHICH COULD REACH ANY WATERWAY
INCLUDING INTERMITTENT DRY CREEKS. THE NATIONAL RESPONSE CENTER CAN BE
REACHED AT (800) 424-8802.
PROTECTIVE MEASURES:
AVOID CONTACT WITH SPILLED MATERIAL. WARN OR EVACUATE OCCUPANTS IN
SURROUNDING AND DOWNWIND AREAS IF REQUIRED DUE TO TOXICITY OR FLAMMABILITY
OF THE MATERIAL. SEE SECTION 5 FOR FIRE FIGHTING INFORMATION. SEE THE
HAZARD IDENTIFICATION SECTION FOR SIGNIFICANT HAZARDS. SEE SECTION 4 FOR
FIRST AID ADVICE. SEE SECTION 8 FOR ADVICE ON THE MINIMUM REQUIREMENTS FOR
PERSONAL PROTECTIVE EQUIPMENT. ADDITIONAL PROTECTIVE MEASURES MAY BE
NECESSARY, DEPENDING ON THE SPECIFIC CIRCUMSTANCES AND/OR THE EXPERT
JUDGMENT OF THE EMERGENCY RESPONDERS.
FOR EMERGENCY RESPONDERS:
RESPIRATORY PROTECTION:
RESPIRATORY PROTECTION WILL BE NECESSARY ONLY IN SPECIAL CASES, E.G.,
FORMATION OF MISTS. HALF-FACE OR FULL-FACE RESPIRATOR WITH FILTER(S) FOR
DUST/ORGANIC VAPOR OR SELF CONTAINED BREATHING APPARATUS (SCBA) CAN BE USED
DEPENDING ON THE SIZE OF SPILL AND POTENTIAL LEVEL OF EXPOSURE. IF THE
EXPOSURE CANNOT BE COMPLETELY CHARACTERIZED OR AN OXYGEN DEFICIENT
ATMOSPHERE IS POSSIBLE OR ANTICIPATED, SCBA IS RECOMMENDED. WORK GLOVES
THAT ARE RESISTANT TO HYDROCARBONS ARE RECOMMENDED. GLOVES MADE OF
POLYVINYL ACETATE (PVA) ARE NOT WATER-RESISTANT AND ARE NOT SUITABLE FOR
EMERGENCY USE. CHEMICAL GOGGLES ARE RECOMMENDED IF SPLASHES OR CONTACT WITH
EYES IS POSSIBLE.
SMALL SPILLS: NORMAL ANTISTATIC WORK CLOTHES ARE USUALLY ADEQUATE.
LARGE SPILLS:
FULL BODY SUIT OF CHEMICAL RESISTANT, ANTISTATIC MATERIAL IS RECOMMENDED.
SPILL MANAGEMENT:
LAND SPILL:
ELIMINATE ALL IGNITION SOURCES (NO SMOKING, FLARES, SPARKS OR FLAMES IN
IMMEDIATE AREA). STOP LEAK IF YOU CAN DO IT WITHOUT RISK. ALL EQUIPMENT
USED WHEN HANDLING THE PRODUCT MUST BE GROUNDED. DO NOT TOUCH OR WALK
THROUGH SPILLED MATERIAL. PREVENT ENTRY INTO WATERWAYS, SEWER, BASEMENTS OR
CONFINED AREAS. A VAPOR SUPPRESSING FOAM MAY BE USED TO REDUCE VAPORS. USE
CLEAN NON-SPARKING TOOLS TO COLLECT ABSORBED MATERIAL. ABSORB OR COVER WITH
DRY EARTH, SAND OR OTHER NON-COMBUSTIBLE MATERIAL AND TRANSFER TO
CONTAINERS.
LARGE SPILLS:
WATER SPRAY MAY REDUCE VAPOR; BUT MAY NOT PREVENT IGNITION IN CLOSED
SPACES. RECOVER BY PUMPING OR WITH SUITABLE ABSORBENT.
WATER SPILL:
STOP LEAK IF YOU CAN DO IT WITHOUT RISK. CONFINE THE SPILL IMMEDIATELY WITH
BOOMS. WARN OTHER SHIPPING. REMOVE FROM THE SURFACE BY SKIMMING OR WITH
SUITABLE ABSORBENTS. SEEK THE ADVICE OF A SPECIALIST BEFORE USING
DISPERSANTS.
WATER SPILL AND LAND SPILL RECOMMENDATIONS ARE BASED ON THE MOST LIKELY
SPILL SCENARIO FOR THIS MATERIAL; HOWEVER, GEOGRAPHIC CONDITIONS, WIND,
TEMPERATURE, (AND IN THE CASE OF A WATER SPILL) WAVE AND CURRENT DIRECTION
AND SPEED MAY GREATLY INFLUENCE THE APPROPRIATE ACTION TO BE TAKEN. FOR
THIS REASON, LOCAL EXPERTS SHOULD BE CONSULTED.
NOTE: LOCAL REGULATIONS MAY PRESCRIBE OR LIMIT ACTION TO BE TAKEN.
ENVIRONMENTAL PRECAUTIONS:
LARGE SPILLS:
DIKE FAR AHEAD OF LIQUID SPILL FOR LATER RECOVERY AND DISPOSAL. PREVENT
ENTRY INTO WATERWAYS, SEWERS, BASEMENTS OR CONFINED AREAS.
| SECTION 7 HANDLING AND STORAGE | |
HANDLING:
AVOID CONTACT WITH SKIN. AVOID PROLONGED BREATHING OF MISTS AND HEATED
VAPOR. PREVENT SMALL SPILLS AND LEAKAGE TO AVOID SLIP HAZARD. MATERIAL CAN
ACCUMULATE STATIC CHARGES WHICH MAY CAUSE AN ELECTRICAL SPARK (IGNITION
SOURCE). WHEN THE MATERIAL IS HANDLED IN BULK, AN ELECTRICAL SPARK COULD
IGNITE ANY FLAMMABLE VAPORS FROM LIQUIDS OR RESIDUES THAT MAY BE PRESENT
(E.G., DURING SWITCH-LOADING OPERATIONS). USE PROPER BONDING AND/OR GROUND
PROCEDURES. HOWEVER, BONDING AND GROUNDS MAY NOT ELIMINATE THE HAZARD FROM
STATIC ACCUMULATION. CONSULT LOCAL APPLICABLE STANDARDS FOR GUIDANCE.
ADDITIONAL REFERENCES INCLUDE AMERICAN PETROLEUM INSTITUTE 2003 (PROTECTION
AGAINST IGNITIONS ARISING OUT OF STATIC, LIGHTNING AND STRAY CURRENTS) OR
NATIONAL FIRE PROTECTION AGENCY 77 (RECOMMENDED PRACTICE ON STATIC
ELECTRICITY) OR CENELEC CLC/TR 50404 (ELECTROSTATICS - CODE OF PRACTICE FOR
THE AVOIDANCE OF HAZARDS DUE TO STATIC ELECTRICITY).
STATIC ACCUMULATOR: THIS MATERIAL IS A STATIC ACCUMULATOR.
STORAGE:
THE CONTAINER CHOICE, FOR EXAMPLE STORAGE VESSEL, MAY EFFECT STATIC
ACCUMULATION AND DISSIPATION. KEEP CONTAINER CLOSED. HANDLE CONTAINERS WITH
CARE. OPEN SLOWLY IN ORDER TO CONTROL POSSIBLE PRESSURE RELEASE. STORE IN A
COOL, WELL-VENTILATED AREA. STORAGE CONTAINERS SHOULD BE GROUNDED AND
BONDED. FIXED STORAGE CONTAINERS, TRANSFER CONTAINERS AND ASSOCIATED
EQUIPMENT SHOULD BE GROUNDED AND BONDED TO PREVENT ACCUMULATION OF STATIC
CHARGE.
| SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION | |
EXPOSURE LIMIT VALUES:
EXPOSURE LIMITS/STANDARDS (NOTE: EXPOSURE LIMITS ARE NOT ADDITIVE)
SOURCE FORM LIMIT / STANDARD NOTE SOURCE
DISTILLATES (PETROLEUM), NON-AEROSOL TWA 200 MG/M3 SKIN ACGIH
HYDROTREATED LIGHT
[TOTAL HYDROCARBON VAPOR]
HYDROTREATED LIGHT MIST. TWA 5 MG/M3 N/A OSHA Z1
NAPHTHENIC DISTILLATE
(PETROLEUM)
HYDROTREATED LIGHT INHALABLE TWA 5 MG/M3 N/A ACGIH
NAPHTHENIC DISTILLATE FRACTION.
(PETROLEUM)
HYDROTREATED LIGHT MIST. TWA 5 MG/M3 N/A ACGIH
NAPHTHENIC DISTILLATE
(PETROLEUM)
HYDROTREATED LIGHT MIST. TWA 5 MG/M3 N/A OSHA Z1
PARAFFINIC DISTILLATES,
PETROLEUM
HYDROTREATED LIGHT INHALABLE TWA 5 MG/M3 N/A ACGIH
PARAFFINIC DISTILLATES, FRACTION.
PETROLEUM
HYDROTREATED LIGHT MIST. TWA 5 MG/M3 N/A ACGIH
PARAFFINIC DISTILLATES,
PETROLEUM
EXPOSURE LIMITS/STANDARDS FOR MATERIALS THAT CAN BE FORMED WHEN HANDLING
THIS PRODUCT:
WHEN MISTS/AEROSOLS CAN OCCUR THE FOLLOWING ARE RECOMMENDED:
5 MG/M3 - ACGIH TLV (INHALABLE FRACTION)
5 MG/M3 - OSHA PEL.
NOTE:
LIMITS/STANDARDS SHOWN FOR GUIDANCE ONLY. FOLLOW APPLICABLE REGULATIONS.
ENGINEERING CONTROLS:
THE LEVEL OF PROTECTION AND TYPES OF CONTROLS NECESSARY WILL VARY DEPENDING
UPON POTENTIAL EXPOSURE CONDITIONS.
CONTROL MEASURES TO CONSIDER:
USE EXPLOSION-PROOF VENTILATION EQUIPMENT TO STAY BELOW EXPOSURE LIMITS.
PERSONAL PROTECTION:
PERSONAL PROTECTIVE EQUIPMENT SELECTIONS VARY BASED ON POTENTIAL EXPOSURE
CONDITIONS SUCH AS APPLICATIONS, HANDLING PRACTICES, CONCENTRATION AND
VENTILATION. INFORMATION ON THE SELECTION OF PROTECTIVE EQUIPMENT FOR USE
WITH THIS MATERIAL, AS PROVIDED BELOW, IS BASED UPON INTENDED, NORMAL
USAGE.
RESPIRATORY PROTECTION:
IF ENGINEERING CONTROLS DO NOT MAINTAIN AIRBORNE CONTAMINANT CONCENTRATIONS
AT A LEVEL WHICH IS ADEQUATE TO PROTECT WORKER HEALTH, AN APPROVED
RESPIRATOR MAY BE APPROPRIATE. RESPIRATOR SELECTION, USE, AND MAINTENANCE
MUST BE IN ACCORDANCE WITH REGULATORY REQUIREMENTS, IF APPLICABLE.
TYPES OF RESPIRATORS TO BE CONSIDERED FOR THIS MATERIAL INCLUDE:
NO SPECIAL REQUIREMENTS UNDER ORDINARY CONDITIONS OF USE AND WITH ADEQUATE
VENTILATION.
FOR HIGH AIRBORNE CONCENTRATIONS, USE AN APPROVED SUPPLIED-AIR RESPIRATOR,
OPERATED IN POSITIVE PRESSURE MODE. SUPPLIED AIR RESPIRATORS WITH AN ESCAPE
BOTTLE MAY BE APPROPRIATE WHEN OXYGEN LEVELS ARE INADEQUATE, GAS/VAPOR
WARNING PROPERTIES ARE POOR, OR IF AIR PURIFYING FILTER CAPACITY/RATING MAY
BE EXCEEDED.
HAND PROTECTION:
ANY SPECIFIC GLOVE INFORMATION PROVIDED IS BASED ON PUBLISHED LITERATURE
AND GLOVE MANUFACTURER DATA. GLOVE SUITABILITY AND BREAKTHROUGH TIME WILL
DIFFER DEPENDING ON THE SPECIFIC USE CONDITIONS. CONTACT THE GLOVE
MANUFACTURER FOR SPECIFIC ADVICE ON GLOVE SELECTION AND BREAKTHROUGH TIMES
FOR YOUR USE CONDITIONS. INSPECT AND REPLACE WORN OR DAMAGED GLOVES.
THE TYPES OF GLOVES TO BE CONSIDERED FOR THIS MATERIAL INCLUDE:
IF PROLONGED OR REPEATED CONTACT IS LIKELY, CHEMICAL RESISTANT GLOVES ARE
RECOMMENDED. IF CONTACT WITH FOREARMS IS LIKELY, WEAR GAUNTLET STYLE
GLOVES.
EYE PROTECTION:
IF CONTACT IS LIKELY, SAFETY GLASSES WITH SIDE SHIELDS ARE RECOMMENDED.
SKIN AND BODY PROTECTION:
ANY SPECIFIC CLOTHING INFORMATION PROVIDED IS BASED ON PUBLISHED LITERATURE
OR MANUFACTURER DATA.
THE TYPES OF CLOTHING TO BE CONSIDERED FOR THIS MATERIAL INCLUDE:
IF PROLONGED OR REPEATED CONTACT IS LIKELY, CHEMICAL, AND OIL RESISTANT
CLOTHING IS RECOMMENDED.
SPECIFIC HYGIENE MEASURES:
ALWAYS OBSERVE GOOD PERSONAL HYGIENE MEASURES, SUCH AS WASHING AFTER
HANDLING THE MATERIAL AND BEFORE EATING, DRINKING, AND/OR SMOKING.
ROUTINELY WASH WORK CLOTHING AND PROTECTIVE EQUIPMENT TO REMOVE
CONTAMINANTS. DISCARD CONTAMINATED CLOTHING AND FOOTWEAR THAT CANNOT BE
CLEANED. PRACTICE GOOD HOUSEKEEPING.
ENVIRONMENTAL CONTROLS:
COMPLY WITH APPLICABLE ENVIRONMENTAL REGULATIONS LIMITING DISCHARGE TO AIR,
WATER AND SOIL. PROTECT THE ENVIRONMENT BY APPLYING APPROPRIATE CONTROL
MEASURES TO PREVENT OR LIMIT EMISSIONS.
| SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES | |
NOTE:
PHYSICAL AND CHEMICAL PROPERTIES ARE PROVIDED FOR SAFETY, HEALTH AND
ENVIRONMENTAL CONSIDERATIONS ONLY AND MAY NOT FULLY REPRESENT PRODUCT
SPECIFICATIONS. CONTACT THE SUPPLIER FOR ADDITIONAL INFORMATION.
GENERAL INFORMATION:
PHYSICAL STATE: LIQUID
COLOR: RED
ODOR: CHARACTERISTIC
ODOR THRESHOLD: N/D
IMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATION:
RELATIVE DENSITY (AT 15 DEG. C): 0.88
FLASH POINT [METHOD]: >82 DEG. C (180 DEG. F) [ASTM D-93]
FLAMMABLE LIMITS (APPROXIMATE VOLUME % IN AIR):
LEL: 0.7
UEL: 7.0 [ESTIMATED]
AUTOIGNITION TEMPERATURE: >225 DEG. C (437 DEG. F)
BOILING POINT / RANGE: N/D
VAPOR DENSITY (AIR = 1): N/D
VAPOR PRESSURE: [N/D AT 20 DEG. C]
EVAPORATION RATE (N-BUTYL ACETATE = 1): N/D
PH: N/A
LOG POW (N-OCTANOL/WATER PARTITION COEFFICIENT): N/D
SOLUBILITY IN WATER: NEGLIGIBLE
VISCOSITY:
13.8 CST (13.8 MM2/SEC) AT 40 DEG. C
5.1 CST (5.1 MM2/SEC) AT 100C
OXIDIZING PROPERTIES: SEE HAZARDS IDENTIFICATION SECTION.
OTHER INFORMATION:
FREEZING POINT: N/D
MELTING POINT: N/A
POUR POINT: -60 DEG. C (-76 DEG. F)
DMSO EXTRACT (MINERAL OIL ONLY), IP-346: <3 % WT
DECOMPOSITION TEMPERATURE: N/D
| SECTION 10 STABILITY AND REACTIVITY | |
STABILITY: MATERIAL IS STABLE UNDER NORMAL CONDITIONS.
CONDITIONS TO AVOID: OPEN FLAMES AND HIGH ENERGY IGNITION SOURCES.
MATERIALS TO AVOID: STRONG OXIDIZERS
HAZARDOUS DECOMPOSITION PRODUCTS:
MATERIAL DOES NOT DECOMPOSE AT AMBIENT TEMPERATURES.
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR.
| SECTION 11 TOXICOLOGICAL INFORMATION | |
ACUTE TOXICITY:
ROUTE OF EXPOSURE CONCLUSION / REMARKS
INHALATION:
TOXICITY (RAT): MINIMALLY TOXIC. BASED ON
LC50: >5000 MG/M3 ASSESSMENT OF THE COMPONENTS.
IRRITATION: NO END POINT DATA. ELEVATED TEMPERATURES OR MECHANICAL
ACTION MAY FORM VAPORS, MIST, OR
FUMES WHICH MAY BE IRRITATING TO
THE EYES, NOSE, THROAT, OR LUNGS.
BASED ON ASSESSMENT OF THE
COMPONENTS.
INGESTION:
TOXICITY (RAT): MINIMALLY TOXIC. BASED ON TEST DATA
LD50: >2000 MG/KG FOR STRUCTURALLY SIMILAR MATERIALS.
SKIN:
TOXICITY (RABBIT): MINIMALLY TOXIC. BASED ON TEST DATA
LD50: >2000 MG/KG FOR STRUCTURALLY SIMILAR MATERIALS.
IRRITATION (RABBIT): DATA AVAILABLE. NEGLIGIBLE IRRITATION TO SKIN AT
AMBIENT TEMPERATURES. BASED ON
ASSESSMENT OF THE COMPONENTS.
EYE:
IRRITATION (RABBIT): DATA AVAILABLE. MAY CAUSE MILD, SHORT-LASTING
DISCOMFORT TO EYES. BASED ON
ASSESSMENT OF THE COMPONENTS.
CHRONIC/OTHER EFFECTS:
FOR THE PRODUCT ITSELF:
REPEATED AND/OR PROLONGED EXPOSURE MAY CAUSE IRRITATION TO THE SKIN, EYES,
OR RESPIRATORY TRACT. SMALL AMOUNTS OF LIQUID ASPIRATED INTO THE LUNGS
DURING INGESTION OR FROM VOMITING MAY CAUSE CHEMICAL PNEUMONITIS OR
PULMONARY EDEMA.
CONTAINS:
BASE OIL SEVERELY REFINED:
NOT CARCINOGENIC IN ANIMAL STUDIES. REPRESENTATIVE MATERIAL PASSES IP-346,
MODIFIED AMES TEST, AND/OR OTHER SCREENING TESTS. DERMAL AND INHALATION
STUDIES SHOWED MINIMAL EFFECTS; LUNG NON-SPECIFIC INFILTRATION OF IMMUNE
CELLS, OIL DEPOSITION AND MINIMAL GRANULOMA FORMATION. NOT SENSITIZING IN
TEST ANIMALS.
ADDITIONAL INFORMATION IS AVAILABLE BY REQUEST.
THE FOLLOWING INGREDIENTS ARE CITED ON THE LISTS BELOW: NONE.
REGULATORY LISTS SEARCHED:
1 = NTP CARC
2 = NTP SUS
3 = IARC 1
4 = IARC 2A
5 = IARC 2B
6 = OSHA CARC
| SECTION 12 ECOLOGICAL INFORMATION | |
THE INFORMATION GIVEN IS BASED ON DATA AVAILABLE FOR THE MATERIAL, THE
COMPONENTS OF THE MATERIAL, AND SIMILAR MATERIALS.
ECOTOXICITY:
MATERIAL -- NOT EXPECTED TO BE HARMFUL TO AQUATIC ORGANISMS.
MOBILITY:
MORE VOLATILE COMPONENT -- HIGHLY VOLATILE, WILL PARTITION RAPIDLY TO AIR.
NOT EXPECTED TO PARTITION TO SEDIMENT AND WASTEWATER SOLIDS.
LESS VOLATILE COMPONENT -- LOW SOLUBILITY AND FLOATS AND IS EXPECTED TO
MIGRATE FROM WATER TO THE LAND. EXPECTED TO PARTITION TO SEDIMENT AND
WASTEWATER SOLIDS.
PERSISTENCE AND DEGRADABILITY:
BIODEGRADATION:
COMPONENTS -- EXPECTED TO BE INHERENTLY BIODEGRADABLE
BIOACCUMULATION POTENTIAL:
MAJORITY OF COMPONENTS -- HAS THE POTENTIAL TO BIOACCUMULATE, HOWEVER
METABOLISM OR PHYSICAL PROPERTIES MAY REDUCE THE BIOCONCENTRATION OR LIMIT
BIOAVAILABILITY.
| SECTION 13 DISPOSAL CONSIDERATIONS | |
DISPOSAL RECOMMENDATIONS BASED ON MATERIAL AS SUPPLIED. DISPOSAL MUST BE IN
ACCORDANCE WITH CURRENT APPLICABLE LAWS AND REGULATIONS, AND MATERIAL
CHARACTERISTICS AT TIME OF DISPOSAL.
DISPOSAL RECOMMENDATIONS:
PRODUCT IS SUITABLE FOR BURNING IN AN ENCLOSED CONTROLLED BURNER FOR FUEL
VALUE OR DISPOSAL BY SUPERVISED INCINERATION AT VERY HIGH TEMPERATURES TO
PREVENT FORMATION OF UNDESIRABLE COMBUSTION PRODUCTS. PROTECT THE
ENVIRONMENT. DISPOSE OF USED OIL AT DESIGNATED SITES. MINIMIZE SKIN
CONTACT. DO NOT MIX USED OILS WITH SOLVENTS, BRAKE FLUIDS OR COOLANTS.
REGULATORY DISPOSAL INFORMATION:
RCRA INFORMATION:
THE UNUSED PRODUCT, IN OUR OPINION, IS NOT SPECIFICALLY LISTED BY THE EPA
AS A HAZARDOUS WASTE (40 CFR, PART 261D), NOR IS IT FORMULATED TO CONTAIN
MATERIALS WHICH ARE LISTED AS HAZARDOUS WASTES. IT DOES NOT EXHIBIT THE
HAZARDOUS CHARACTERISTICS OF IGNITABILITY, CORROSITIVITY OR REACTIVITY AND
IS NOT FORMULATED WITH CONTAMINANTS AS DETERMINED BY THE TOXICITY
CHARACTERISTIC LEACHING PROCEDURE (TCLP). HOWEVER, USED PRODUCT MAY BE
REGULATED.
EMPTY CONTAINER WARNING EMPTY CONTAINER WARNING (WHERE APPLICABLE):
EMPTY CONTAINERS MAY CONTAIN RESIDUE AND CAN BE DANGEROUS. DO NOT ATTEMPT
TO REFILL OR CLEAN CONTAINERS WITHOUT PROPER INSTRUCTIONS. EMPTY DRUMS
SHOULD BE COMPLETELY DRAINED AND SAFELY STORED UNTIL APPROPRIATELY
RECONDITIONED OR DISPOSED. EMPTY CONTAINERS SHOULD BE TAKEN FOR RECYCLING,
RECOVERY, OR DISPOSAL THROUGH SUITABLY QUALIFIED OR LICENSED CONTRACTOR AND
IN ACCORDANCE WITH GOVERNMENTAL REGULATIONS. DO NOT PRESSURISE, CUT, WELD,
BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE SUCH CONTAINERS TO HEAT, FLAME,
SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION. THEY MAY EXPLODE
AND CAUSE INJURY OR DEATH.
| SECTION 14 TRANSPORT INFORMATION | |
LAND (DOT)
PROPER SHIPPING NAME:
COMBUSTIBLE LIQUID, N.O.S. (DISTILLATES (PETROLEUM), HYDROTREATED LIGHT)
HAZARD CLASS & DIVISION: COMBUSTIBLE LIQUID
ID NUMBER: NA1993
PACKING GROUP: III
ERG NUMBER: 128
LABEL(S): NONE
TRANSPORT DOCUMENT NAME:
NA1993, COMBUSTIBLE LIQUID, N.O.S. (DISTILLATES (PETROLEUM), HYDROTREATED
LIGHT), COMBUSTIBLE LIQUID, PG III
FOOTNOTE:
THIS MATERIAL IS NOT REGULATED UNDER 49 CFR IN A CONTAINER OF 119 GALLON
CAPACITY OR LESS WHEN TRANSPORTED SOLELY BY LAND, AS LONG AS THE MATERIAL
IS NOT A HAZARDOUS WASTE, A MARINE POLLUTANT, OR SPECIFICALLY LISTED AS A
HAZARDOUS SUBSTANCE.
LAND (TDG): NOT REGULATED FOR LAND TRANSPORT
SEA (IMDG): NOT REGULATED FOR SEA TRANSPORT ACCORDING TO IMDG-CODE
AIR (IATA): NOT REGULATED FOR AIR TRANSPORT
| SECTION 15 REGULATORY INFORMATION | |
OSHA HAZARD COMMUNICATION STANDARD:
WHEN USED FOR ITS INTENDED PURPOSE, THIS MATERIAL IS CLASSIFIED AS
HAZARDOUS IN ACCORDANCE WITH OSHA 29 CFR 1910.1200.
COMPLIES WITH THE FOLLOWING NATIONAL/REGIONAL CHEMICAL INVENTORY
REQUIREMENTS:
KECI, EINECS, PICCS, IECSC, TSCA, DSL, AICS, ENCS
EPCRA: THIS MATERIAL CONTAINS NO EXTREMELY HAZARDOUS SUBSTANCES.
SARA (311/312) REPORTABLE HAZARD CATEGORIES: FIRE. DELAYED HEALTH.
SARA (313) TOXIC RELEASE INVENTORY:
THIS MATERIAL CONTAINS NO CHEMICALS SUBJECT TO THE SUPPLIER NOTIFICATION
REQUIREMENTS OF THE SARA 313 TOXIC RELEASE PROGRAM.
THE FOLLOWING INGREDIENTS ARE CITED ON THE LISTS BELOW:
CHEMICAL NAME CAS NUMBER LIST CITATIONS
DISTILLATES (PETROLEUM), 64742-47-8 1, 17, 18, 19
HYDROTREATED LIGHT
HYDROTREATED LIGHT NAPHTHENIC 64742-53-6 1, 4, 13, 17, 18, 19
DISTILLATE (PETROLEUM)
HYDROTREATED LIGHT PARAFFINIC 64742-55-8 1, 4, 17, 18, 19
DISTILLATES, PETROLEUM
REGULATORY LISTS SEARCHED:
1 = ACGIH ALL
2 = ACGIH A1
3 = ACGIH A2
4 = OSHA Z
5 = TSCA 4
6 = TSCA 5A2
7 = TSCA 5E
8 = TSCA 6
9 = TSCA 12B
10 = CA P65 CARC
11 = CA P65 REPRO
12 = CA RTK
13 = IL RTK
14 = LA RTK
15 = MI 293
16 = MN RTK
17 = NJ RTK
18 = PA RTK
19 = RI RTK
CODE KEY:
CARC = CARCINOGEN
REPRO = REPRODUCTIVE
| SECTION 16 OTHER INFORMATION | |
N/D = NOT DETERMINED
N/A = NOT APPLICABLE
THIS SAFETY DATA SHEET CONTAINS THE FOLLOWING REVISIONS:
REVISION CHANGES:
SECTION 06: PROTECTIVE MEASURES WAS MODIFIED.
SECTION 13:
DISPOSAL CONSIDERATIONS - DISPOSAL RECOMMENDATIONS WAS MODIFIED.
SECTION 09: PHYS/CHEM PROPERTIES NOTE WAS MODIFIED.
SECTION 08: COMPLY WITH APPLICABLE REGULATIONS PHRASE WAS MODIFIED.
SECTION 09: RELATIVE DENSITY - HEADER WAS MODIFIED.
SECTION 09: FLASH POINT C(F) WAS MODIFIED.
SECTION 09: VISCOSITY WAS MODIFIED.
COMPOSITION: COMPONENT TABLE WAS MODIFIED.
SECTION 15: LIST CITATIONS TABLE WAS MODIFIED.
SECTION 15: NATIONAL CHEMICAL INVENTORY LISTING - HEADER WAS MODIFIED.
SECTION 15: NATIONAL CHEMICAL INVENTORY LISTING WAS MODIFIED.
SECTION 08: EXPOSURE LIMITS/STANDARDS WAS MODIFIED.
SECTION 08: EXPOSURE LIMITS TABLE WAS MODIFIED.
SECTION 09: DECOMPOSITION TEMPERATURE WAS ADDED.
SECTION 09: DECOMPOSITION TEMP - HEADER WAS ADDED.
PRECAUTIONARY LABEL TEXT:
CONTAINS: DISTILLATES (PETROLEUM), HYDROTREATED LIGHT
CAUTION!
HEALTH HAZARDS:
REPEATED EXPOSURE MAY CAUSE SKIN DRYNESS OR CRACKING. IF SWALLOWED, MAY BE
ASPIRATED AND CAUSE LUNG DAMAGE.
TARGET ORGANS: SKIN
PHYSICAL HAZARDS:
COMBUSTIBLE. MATERIAL CAN ACCUMULATE STATIC CHARGES WHICH MAY CAUSE AN
IGNITION.
PRECAUTIONS:
USE PROPER BONDING AND/OR GROUND PROCEDURES. HOWEVER, BONDING AND GROUNDS
MAY NOT ELIMINATE THE HAZARD FROM STATIC ACCUMULATION.
FIRST AID:
INHALATION:
REMOVE FROM FURTHER EXPOSURE. FOR THOSE PROVIDING ASSISTANCE, AVOID
EXPOSURE TO YOURSELF OR OTHERS. USE ADEQUATE RESPIRATORY PROTECTION. IF
RESPIRATORY IRRITATION, DIZZINESS, NAUSEA, OR UNCONSCIOUSNESS OCCURS, SEEK
IMMEDIATE MEDICAL ASSISTANCE. IF BREATHING HAS STOPPED, ASSIST VENTILATION
WITH A MECHANICAL DEVICE OR USE MOUTH-TO-MOUTH RESUSCITATION.
EYE:
FLUSH THOROUGHLY WITH WATER. IF IRRITATION OCCURS, GET MEDICAL ASSISTANCE.
ORAL:
SEEK IMMEDIATE MEDICAL ATTENTION. DO NOT INDUCE VOMITING. IF INGESTED,
MATERIAL MAY BE ASPIRATED INTO THE LUNGS AND CAUSE CHEMICAL PNEUMONITIS.
TREAT APPROPRIATELY.
SKIN:
WASH CONTACT AREAS WITH SOAP AND WATER. IF PRODUCT IS INJECTED INTO OR
UNDER THE SKIN, OR INTO ANY PART OF THE BODY, REGARDLESS OF THE APPEARANCE
OF THE WOUND OR ITS SIZE, THE INDIVIDUAL SHOULD BE EVALUATED IMMEDIATELY BY
A PHYSICIAN AS A SURGICAL EMERGENCY. EVEN THOUGH INITIAL SYMPTOMS FROM HIGH
PRESSURE INJECTION MAY BE MINIMAL OR ABSENT, EARLY SURGICAL TREATMENT
WITHIN THE FIRST FEW HOURS MAY SIGNIFICANTLY REDUCE THE ULTIMATE EXTENT OF
INJURY.
FIRE FIGHTING MEDIA:
USE WATER FOG, FOAM, DRY CHEMICAL OR CARBON DIOXIDE (CO2) TO EXTINGUISH
FLAMES.
SPILL/LEAK:
LAND SPILL:
ELIMINATE ALL IGNITION SOURCES (NO SMOKING, FLARES, SPARKS OR FLAMES IN
IMMEDIATE AREA). STOP LEAK IF YOU CAN DO IT WITHOUT RISK. PREVENT ENTRY
INTO WATERWAYS, SEWER, BASEMENTS OR CONFINED AREAS. A VAPOR SUPPRESSING
FOAM MAY BE USED TO REDUCE VAPORS. ABSORB OR COVER WITH DRY EARTH, SAND OR
OTHER NON-COMBUSTIBLE MATERIAL AND TRANSFER TO CONTAINERS. RECOVER BY
PUMPING OR WITH SUITABLE ABSORBENT.
WATER SPILL:
STOP LEAK IF YOU CAN DO IT WITHOUT RISK. CONFINE THE SPILL IMMEDIATELY WITH
BOOMS. WARN OTHER SHIPPING. REMOVE FROM THE SURFACE BY SKIMMING OR WITH
SUITABLE ABSORBENTS. SEEK THE ADVICE OF A SPECIALIST BEFORE USING
DISPERSANTS.
USE: NOT INTENDED OR SUITABLE FOR USE IN OR AROUND A HOUSEHOLD OR DWELLING.
THE INFORMATION AND RECOMMENDATIONS CONTAINED HEREIN ARE, TO THE BEST OF
EXXONMOBIL'S KNOWLEDGE AND BELIEF, ACCURATE AND RELIABLE AS OF THE DATE
ISSUED. YOU CAN CONTACT EXXONMOBIL TO INSURE THAT THIS DOCUMENT IS THE MOST
CURRENT AVAILABLE FROM EXXONMOBIL. THE INFORMATION AND RECOMMENDATIONS ARE
OFFERED FOR THE USER'S CONSIDERATION AND EXAMINATION. IT IS THE USER'S
RESPONSIBILITY TO SATISFY ITSELF THAT THE PRODUCT IS SUITABLE FOR THE
INTENDED USE. IF BUYER REPACKAGES THIS PRODUCT, IT IS THE USER'S
RESPONSIBILITY TO INSURE PROPER HEALTH, SAFETY AND OTHER NECESSARY
INFORMATION IS INCLUDED WITH AND/OR ON THE CONTAINER. APPROPRIATE WARNINGS
AND SAFE-HANDLING PROCEDURES SHOULD BE PROVIDED TO HANDLERS AND USERS.
ALTERATION OF THIS DOCUMENT IS STRICTLY PROHIBITED. EXCEPT TO THE EXTENT
REQUIRED BY LAW, RE-PUBLICATION OR RETRANSMISSION OF THIS DOCUMENT, IN
WHOLE OR IN PART, IS NOT PERMITTED. THE TERM, "EXXONMOBIL" IS USED FOR
CONVENIENCE, AND MAY INCLUDE ANY ONE OR MORE OF EXXONMOBIL CHEMICAL
COMPANY, EXXON MOBIL CORPORATION, OR ANY AFFILIATES IN WHICH THEY DIRECTLY
OR INDIRECTLY HOLD ANY INTEREST.
INTERNAL USE ONLY:
MHC: 2A, 0, 0, 0, 0, 1
PPEC: C
DGN: 2005454XUS (552975)
COPYRIGHT 2002 EXXON MOBIL CORPORATION, ALL RIGHTS RESERVED