| Common Name: | STRUST SSPR 6PK METALC GOLD, 7710830 |
| Manufacturer: | RUST-OLEUM |
| SDS Revision Date: | 5/7/2011 |
| SDS Format: | ANSI-OSHA |
| Item Number(s): | 30RK21, 30RK22, 30RK23, 30RK24 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
7710830 STRUST SSPR 6PK METALC GOLD
MATERIAL SAFETY DATA SHEET
24 HOUR ASSISTANCE:
1-847-367-7700
RUST-OLEUM CORP.
WWW.RUSTOLEUM.COM
| SECTION 1 - CHEMICAL PRODUCT / COMPANY INFORMATION |  |
PRODUCT NAME: STRUST SSPR 6PK METALC GOLD
IDENTIFICATION NUMBER: 7710830
PRODUCT USE/CLASS: METALLIC / AEROSOL
SUPPLIER:
RUST-OLEUM CORPORATION
11 HAWTHORN PARKWAY
VERNON HILLS, IL 60061
USA
MANUFACTURER:
RUST-OLEUM CORPORATION
11 HAWTHORN PARKWAY
VERNON HILLS, IL 60061
USA
PREPARER: REGULATORY DEPARTMENT
REVISION DATE: 05/07/2011
| SECTION 2 - COMPOSITION / INFORMATION ON INGREDIENTS | |
CHEMICAL NAME CAS NUMBER WEIGHT % LESS THAN
TOLUENE 108-88-3 35.0
LIQUEFIED PETROLEUM GAS 68476-86-8 35.0
ACETONE 67-64-1 25.0
PROPYLENE GLYCOL MONOMETHYL 108-65-6 5.0
ETHER ACETATE
COPPER COMPOUNDS 7440-50-8 5.0
CHEMICAL NAME ACGIH ACGIH OSHA OSHA PEL
TLV-TWA TLV-STEL PEL-TWA CEILING
TOLUENE 20 PPM N.E. 200 PPM 300 PPM
LIQUEFIED PETROLEUM GAS N.E. N.E. N.E. N.E.
ACETONE 500 PPM 750 PPM 1000 PPM N.E.
PROPYLENE GLYCOL MONOMETHYL N.E. N.E. 30 PPM N.E.
ETHER ACETATE
COPPER COMPOUNDS 1 MG/M3 N.E. 1 MG/M3 N.E.
(DUST) (DUST)
| SECTION 3 - HAZARDS IDENTIFICATION | |
EMERGENCY OVERVIEW:
CONTENTS UNDER PRESSURE. HARMFUL IF INHALED. MAY AFFECT THE BRAIN OR NERVOUS
SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA. VAPORS MAY CAUSE FLASH FIRE OR
EXPLOSION. HARMFUL IF SWALLOWED. EXTREMELY FLAMMABLE LIQUID AND VAPOR.
EFFECTS OF OVEREXPOSURE - EYE CONTACT: CAUSES EYE IRRITATION.
EFFECTS OF OVEREXPOSURE - SKIN CONTACT:
PROLONGED OR REPEATED CONTACT MAY CAUSE SKIN IRRITATION. SUBSTANCE MAY
CAUSE SLIGHT SKIN IRRITATION.
EFFECTS OF OVEREXPOSURE - INHALATION:
HIGH VAPOR CONCENTRATIONS ARE IRRITATING TO THE EYES, NOSE, THROAT AND
LUNGS. AVOID BREATHING VAPORS OR MISTS. HIGH GAS, VAPOR, MIST OR DUST
CONCENTRATIONS MAY BE HARMFUL IF INHALED. HARMFUL IF INHALED.
EFFECTS OF OVEREXPOSURE - INGESTION:
ASPIRATION HAZARD IF SWALLOWED; CAN ENTER LUNGS AND CAUSE DAMAGE. SUBSTANCE
MAY BE HARMFUL IF SWALLOWED.
EFFECTS OF OVEREXPOSURE - CHRONIC HAZARDS:
MAY CAUSE CENTRAL NERVOUS SYSTEM DISORDER (E.G., NARCOSIS INVOLVING A LOSS
OF COORDINATION, WEAKNESS, FATIGUE, MENTAL CONFUSION, AND BLURRED VISION)
AND/OR DAMAGE. REPORTS HAVE ASSOCIATED REPEATED AND PROLONGED OCCUPATIONAL
OVEREXPOSURE TO SOLVENTS WITH PERMANENT BRAIN AND NERVOUS SYSTEM DAMAGE.
PRIMARY ROUTE(S) OF ENTRY:
SKIN CONTACT, SKIN ABSORPTION, INHALATION, INGESTION, EYE CONTACT
| SECTION 4 - FIRST AID MEASURES | |
FIRST AID - EYE CONTACT:
IMMEDIATELY FLUSH EYES WITH PLENTY OF WATER FOR AT LEAST 15 MINUTES HOLDING
EYELIDS OPEN. GET MEDICAL ATTENTION. DO NOT ALLOW RUBBING OF EYES OR KEEPING
EYES CLOSED.
FIRST AID - SKIN CONTACT:
WASH WITH SOAP AND WATER. GET MEDICAL ATTENTION IF IRRITATION DEVELOPS OR
PERSISTS.
FIRST AID - INHALATION:
IF YOU EXPERIENCE DIFFICULTY IN BREATHING, LEAVE THE AREA TO OBTAIN
FRESH AIR. IF CONTINUED DIFFICULTY IS EXPERIENCED, GET MEDICAL ASSISTANCE
IMMEDIATELY.
FIRST AID - INGESTION:
ASPIRATION HAZARD:
DO NOT INDUCE VOMITING OR GIVE ANYTHING BY MOUTH BECAUSE THIS MATERIAL
CAN ENTER THE LUNGS AND CAUSE SEVERE LUNG DAMAGE. GET IMMEDIATE MEDICAL
ATTENTION.
| SECTION 5 - FIRE FIGHTING MEASURES | |
FLASH POINT: -156 F (SETAFLASH)
EXTINGUISHING MEDIA:
FILM FORMING FOAM, CARBON DIOXIDE, DRY CHEMICAL, WATER FOG
UNUSUAL FIRE AND EXPLOSION HAZARDS:
FLASH POINT IS LESS THAN 20 DEG. F. - EXTREMELY FLAMMABLE LIQUID AND VAPOR!
PERFORATION OF THE PRESSURIZED CONTAINER MAY CAUSE BURSTING OF THE CAN.
ISOLATE FROM HEAT, ELECTRICAL EQUIPMENT, SPARKS AND OPEN FLAME. KEEP
CONTAINERS TIGHTLY CLOSED. WATER SPRAY MAY BE INEFFECTIVE. CLOSED CONTAINERS
MAY EXPLODE WHEN EXPOSED TO EXTREME HEAT. VAPORS MAY FORM EXPLOSIVE MIXTURES
WITH AIR. VAPORS CAN TRAVEL TO A SOURCE OF IGNITION AND FLASH BACK.
SPECIAL FIREFIGHTING PROCEDURES:
EVACUATE AREA AND FIGHT FIRE FROM A SAFE DISTANCE.
| SECTION 6 - ACCIDENTAL RELEASE MEASURES | |
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED:
CONTAIN SPILLED LIQUID WITH SAND OR EARTH. DO NOT USE COMBUSTIBLE MATERIALS
SUCH AS SAWDUST. REMOVE ALL SOURCES OF IGNITION, VENTILATE AREA AND REMOVE
WITH INERT ABSORBENT AND NON-SPARKING TOOLS. DISPOSE OF ACCORDING TO LOCAL,
STATE (PROVINCIAL) AND FEDERAL REGULATIONS. DO NOT INCINERATE CLOSED
CONTAINERS.
| SECTION 7 - HANDLING AND STORAGE | |
HANDLING:
FOLLOW ALL MSDS/LABEL PRECAUTIONS EVEN AFTER CONTAINER IS EMPTIED BECAUSE
IT MAY RETAIN PRODUCT RESIDUES. USE ONLY IN A WELL-VENTILATED AREA. AVOID
BREATHING VAPOR OR MIST. WASH THOROUGHLY AFTER HANDLING. WASH HANDS BEFORE
EATING.
STORAGE:
DO NOT STORE ABOVE 120 DEG. F. STORE LARGE QUANTITIES IN BUILDINGS DESIGNED
AND PROTECTED FOR STORAGE OF NFPA CLASS I FLAMMABLE LIQUIDS. CONTENTS UNDER
PRESSURE. DO NOT EXPOSE TO HEAT OR STORE ABOVE 120 DEG. F. KEEP CONTAINERS
TIGHTLY CLOSED. ISOLATE FROM HEAT, ELECTRICAL EQUIPMENT, SPARKS AND OPEN
FLAME.
| SECTION 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION | |
ENGINEERING CONTROLS:
PREVENT BUILD-UP OF VAPORS BY OPENING ALL DOORS AND WINDOWS TO ACHIEVE
CROSS-VENTILATION. USE EXPLOSION-PROOF VENTILATION EQUIPMENT. USE PROCESS
ENCLOSURES, LOCAL EXHAUST VENTILATION, OR OTHER ENGINEERING CONTROLS TO
CONTROL AIRBORNE LEVELS BELOW RECOMMENDED EXPOSURE LIMITS.
RESPIRATORY PROTECTION:
A RESPIRATORY PROTECTION PROGRAM THAT MEETS OSHA 1910.134 AND ANSI Z88.2
REQUIREMENTS MUST BE FOLLOWED WHENEVER WORKPLACE CONDITIONS WARRANT A
RESPIRATOR'S USE. A NIOSH/MSHA APPROVED AIR PURIFYING RESPIRATOR WITH AN
ORGANIC VAPOR CARTRIDGE OR CANISTER MAY BE PERMISSIBLE UNDER CERTAIN
CIRCUMSTANCES WHERE AIRBORNE CONCENTRATIONS ARE EXPECTED TO EXCEED EXPOSURE
LIMITS.
PROTECTION PROVIDED BY AIR PURIFYING RESPIRATORS IS LIMITED. USE A
POSITIVE PRESSURE AIR SUPPLIED RESPIRATOR IF THERE IS ANY POTENTIAL FOR
AN UNCONTROLLED RELEASE, EXPOSURE LEVELS ARE NOT KNOWN, OR IN ANY OTHER
CIRCUMSTANCES WHERE AIR PURIFYING RESPIRATORS MAY NOT PROVIDE ADEQUATE
PROTECTION.
SKIN PROTECTION:
NITRILE OR NEOPRENE GLOVES MAY AFFORD ADEQUATE SKIN PROTECTION. USE
IMPERVIOUS GLOVES TO PREVENT SKIN CONTACT AND ABSORPTION OF THIS MATERIAL
THROUGH THE SKIN.
EYE PROTECTION:
USE SAFETY EYEWEAR DESIGNED TO PROTECT AGAINST SPLASH OF LIQUIDS.
OTHER PROTECTIVE EQUIPMENT:
REFER TO SAFETY SUPERVISOR OR INDUSTRIAL HYGIENIST FOR FURTHER INFORMATION
REGARDING PERSONAL PROTECTIVE EQUIPMENT AND ITS APPLICATION.
HYGIENIC PRACTICES:
WASH THOROUGHLY WITH SOAP AND WATER BEFORE EATING, DRINKING OR SMOKING.
| SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES | |
VAPOR DENSITY: HEAVIER THAN AIR
ODOR: SOLVENT LIKE
APPEARANCE: AEROSOLIZED MIST
EVAPORATION RATE: FASTER THAN ETHER
SOLUBILITY IN H2O: SLIGHT
FREEZE POINT: N.D.
SPECIFIC GRAVITY: 0.747
PH: N.D.
PHYSICAL STATE: LIQUID
(SEE SECTION 16 FOR ABBREVIATION LEGEND)
| SECTION 10 - STABILITY AND REACTIVITY | |
CONDITIONS TO AVOID:
AVOID TEMPERATURES ABOVE 120 DEG. F. AVOID ALL POSSIBLE SOURCES OF IGNITION.
INCOMPATIBILITY:
INCOMPATIBLE WITH STRONG OXIDIZING AGENTS, STRONG ACIDS AND STRONG ALKALIES.
HAZARDOUS DECOMPOSITION:
BY OPEN FLAME, CARBON MONOXIDE AND CARBON DIOXIDE. WHEN HEATED TO
DECOMPOSITION, IT EMITS ACRID SMOKE AND IRRITATING FUMES.
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR UNDER NORMAL CONDITIONS.
STABILITY: THIS PRODUCT IS STABLE UNDER NORMAL STORAGE CONDITIONS.
| SECTION 11 - TOXICOLOGICAL INFORMATION | |
CHEMICAL NAME LD50 LC50
TOLUENE 636 MG/KG >26700 PPM (RAT,
(RAT, ORAL) INHALATION, 1HR)
LIQUEFIED PETROLEUM GAS N.E. N.E.
ACETONE 5800 MG/KG (RAT) 50100 MG/M3 (RAT, 8HR)
PROPYLENE GLYCOL MONOMETHYL >10000 MG/KG N.E.
ETHER ACETATE (RAT, ORAL)
COPPER COMPOUNDS N.E. N.E.
| SECTION 12 - ECOLOGICAL INFORMATION | |
ECOLOGICAL INFORMATION: PRODUCT IS A MIXTURE OF LISTED COMPONENTS.
| SECTION 13 - DISPOSAL INFORMATION | |
DISPOSAL INFORMATION:
DISPOSE OF MATERIAL IN ACCORDANCE TO LOCAL, STATE AND FEDERAL REGULATIONS
AND ORDINANCES. DO NOT ALLOW TO ENTER STORM DRAINS OR SEWER SYSTEMS.
| SECTION 14 - TRANSPORTATION INFORMATION | |
DOMESTIC (USDOT) INTERNATIONAL (IMDG) AIR (IATA)
PROPER SHIPPING NAME CONSUMER COMMODITY AEROSOLS AEROSOLS
HAZARD CLASS ORM-D 2.1 2.1
UN NUMBER N.A. UN1950 UN1950
PACKING GROUP N.A. N.A. N.A.
LIMITED QUANTITY NO YES YES
| SECTION 15 - REGULATORY INFORMATION | |
CERCLA - SARA HAZARD CATEGORY:
THIS PRODUCT HAS BEEN REVIEWED ACCORDING TO THE EPA "HAZARD CATEGORIES"
PROMULGATED UNDER SECTIONS 311 AND 312 OF THE SUPERFUND AMENDMENT AND
REAUTHORIZATION ACT OF 1986 (SARA TITLE III) AND IS CONSIDERED, UNDER
APPLICABLE DEFINITIONS, TO MEET THE FOLLOWING CATEGORIES:
IMMEDIATE HEALTH HAZARD, CHRONIC HEALTH HAZARD, FIRE HAZARD, PRESSURIZED GAS
HAZARD
SARA SECTION 313:
LISTED BELOW ARE THE SUBSTANCES (IF ANY) CONTAINED IN THIS PRODUCT THAT ARE
SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313 OF TITLE III OF THE
SUPERFUND AMENDMENT AND REAUTHORIZATION ACT OF 1986 AND 40 CFR PART 372:
CHEMICAL NAME CAS NUMBER
TOLUENE 108-88-3
COPPER COMPOUNDS 7440-50-8
TOXIC SUBSTANCES CONTROL ACT:
LISTED BELOW ARE THE SUBSTANCES (IF ANY) CONTAINED IN THIS PRODUCT THAT ARE
SUBJECT TO THE REPORTING REQUIREMENTS OF TSCA 12(B) IF EXPORTED FROM THE
UNITED STATES:
U.S. STATE REGULATIONS: AS FOLLOWS -
NEW JERSEY RIGHT-TO-KNOW:
THE FOLLOWING MATERIALS ARE NON-HAZARDOUS, BUT ARE AMONG THE TOP FIVE
COMPONENTS IN THIS PRODUCT.
CHEMICAL NAME CAS NUMBER
ACRYLIC RESIN PROPRIETARY
PENNSYLVANIA RIGHT-TO-KNOW:
THE FOLLOWING NON-HAZARDOUS INGREDIENTS ARE PRESENT IN THE PRODUCT AT
GREATER THAN 3%.
CHEMICAL NAME CAS NUMBER
ACRYLIC RESIN PROPRIETARY
INTERNATIONAL REGULATIONS: AS FOLLOWS -
CANADIAN WHMIS:
THIS MSDS HAS BEEN PREPARED IN COMPLIANCE WITH CONTROLLED PRODUCT
REGULATIONS EXCEPT FOR THE USE OF THE 16 HEADINGS.
CANADIAN WHMIS CLASS:
AB5
D2A
D2B
| SECTION 16 - OTHER INFORMATION | |
HMIS RATINGS:
HEALTH 2*
FLAMMABILITY 4
REACTIVITY 0
PERSONAL PROTECTION X
NFPA RATINGS:
HEALTH 2
FLAMMABILITY 4
INSTABILITY 0
VOLATILE ORGANIC COMPOUNDS, G/L: 633
REASON FOR REVISION: REGULATORY UPDATE
LEGEND:
N.A. - NOT APPLICABLE
N.E. - NOT ESTABLISHED
N.D. - NOT DETERMINED
RUST-OLEUM CORPORATION BELIEVES, TO THE BEST OF ITS KNOWLEDGE, INFORMATION
AND BELIEF, THE INFORMATION CONTAINED HEREIN TO BE ACCURATE AND RELIABLE AS
OF THE DATE OF THIS MATERIAL SAFETY DATA SHEET. HOWEVER, BECAUSE THE
CONDITIONS OF HANDLING, USE, AND STORAGE OF THESE MATERIALS ARE BEYOND OUR
CONTROL, WE ASSUME NO RESPONSIBILITY OR LIABILITY FOR PERSONAL INJURY OR
PROPERTY DAMAGE INCURRED BY THE USE OF THESE MATERIALS. RUST-OLEUM
CORPORATION MAKES NO WARRANTY, EXPRESSED OR IMPLIED, REGARDING THE ACCURACY
OR RELIABILITY OF THE DATA OR RESULTS OBTAINED FROM THEIR USE. ALL MATERIALS
MAY PRESENT UNKNOWN HAZARDS AND SHOULD BE USED WITH CAUTION. THE INFORMATION
AND RECOMMENDATIONS IN THIS MATERIAL SAFETY DATA SHEET ARE OFFERED FOR THE
USERS' CONSIDERATION AND EXAMINATION. IT IS THE RESPONSIBILITY OF THE USER
TO DETERMINE THE FINAL SUITABILITY OF THIS INFORMATION AND TO COMPLY WITH
ALL APPLICABLE INTERNATIONAL, FEDERAL, STATE, AND LOCAL LAWS AND
REGULATIONS.