| Common Name: | VELOCITE OIL NO. 6 |
| Manufacturer: | EXXON MOBIL |
| SDS Revision Date: | 3/16/2015 |
| SDS Format: | GHS-US |
| Item Number(s): | 4F974, 4ZF38 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
EXXONMOBIL
PRODUCT NAME: MOBIL VELOCITE OIL NO. 6
REVISION DATE: 16 MAR 2015
SAFETY DATA SHEET
| SECTION 1 PRODUCT AND COMPANY IDENTIFICATION |  |
PRODUCT:
PRODUCT NAME: MOBIL VELOCITE OIL NO. 6
PRODUCT DESCRIPTION: BASE OIL AND ADDITIVES
PRODUCT CODE: 201560509080, 600668-00, 970334
INTENDED USE: CIRCULATING/GEAR OIL
COMPANY IDENTIFICATION:
SUPPLIER:
EXXON MOBIL CORPORATION
22777 SPRINGWOODS VILLAGE PARKWAY
SPRING, TX. 77389
USA
24 HOUR HEALTH EMERGENCY: 609-737-4411
TRANSPORTATION EMERGENCY PHONE: 800-424-9300 OR 703-527-3887 CHEMTREC
PRODUCT TECHNICAL INFORMATION: 800-662-4525
MSDS INTERNET ADDRESS:
HTTP://WWW.EXXON.COM
HTTP://WWW.MOBIL.COM
| SECTION 2 HAZARDS IDENTIFICATION | |
THIS MATERIAL IS HAZARDOUS ACCORDING TO REGULATORY GUIDELINES (SEE (M)SDS
SECTION 15).
CLASSIFICATION:
ASPIRATION TOXICANT: CATEGORY 1.
LABEL:
PICTOGRAM: HEALTH HAZARD
SIGNAL WORD: DANGER
HAZARD STATEMENTS:
H304: MAY BE FATAL IF SWALLOWED AND ENTERS AIRWAYS.
PRECAUTIONARY STATEMENTS:
P273: AVOID RELEASE TO THE ENVIRONMENT.
P301 + P310:
IF SWALLOWED: IMMEDIATELY CALL A POISON CENTER OR DOCTOR/PHYSICIAN.
P331: DO NOT INDUCE VOMITING.
P405: STORE LOCKED UP.
P501:
DISPOSE OF CONTENTS AND CONTAINER IN ACCORDANCE WITH LOCAL REGULATIONS.
OTHER HAZARD INFORMATION:
HAZARD NOT OTHERWISE CLASSIFIED (HNOC):
NONE AS DEFINED UNDER 29 CFR 1910.1200.
PHYSICAL / CHEMICAL HAZARDS: NO SIGNIFICANT HAZARDS.
HEALTH HAZARDS:
HIGH-PRESSURE INJECTION UNDER SKIN MAY CAUSE SERIOUS DAMAGE. EXCESSIVE
EXPOSURE MAY RESULT IN EYE, SKIN, OR RESPIRATORY IRRITATION.
ENVIRONMENTAL HAZARDS:
EXPECTED TO BE HARMFUL TO AQUATIC ORGANISMS. MAY CAUSE LONG-TERM ADVERSE
EFFECTS IN THE AQUATIC ENVIRONMENT.
NFPA HAZARD ID:
HEALTH 1
FLAMMABILITY 1
REACTIVITY 0
HMIS HAZARD ID:
HEALTH 1*
FLAMMABILITY 1
REACTIVITY 0
NOTE:
THIS MATERIAL SHOULD NOT BE USED FOR ANY OTHER PURPOSE THAN THE INTENDED
USE IN SECTION 1 WITHOUT EXPERT ADVICE. HEALTH STUDIES HAVE SHOWN THAT
CHEMICAL EXPOSURE MAY CAUSE POTENTIAL HUMAN HEALTH RISKS WHICH MAY VARY
FROM PERSON TO PERSON.
| SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTS | |
THIS MATERIAL IS DEFINED AS A MIXTURE.
HAZARDOUS SUBSTANCE(S) OR COMPLEX SUBSTANCE(S) REQUIRED FOR DISCLOSURE:
NAME CAS# CONCENTRATION* GHS HAZARD
CODES
2,6-DITERTBUTYL PHENOL 128-39-2 0.1 - <1% H315, H319(2A),
H400
(M FACTOR 1),
H410(M FACTOR 1)
SOLVENT REFINED LIGHT 64741-89-5 90 - <100% H304
PARAFFINIC DISTILLATE
(PETROLEUM)
STRAIGHT-RUN MIDDLE 64741-44-2 5 - <10% H304, H401, H411
DISTILLATES
* ALL CONCENTRATIONS ARE PERCENT BY WEIGHT UNLESS MATERIAL IS A GAS.
GAS CONCENTRATIONS ARE IN PERCENT BY VOLUME.
AS PER PARAGRAPH (I) OF 29 CFR 1910.1200, FORMULATION IS CONSIDERED
A TRADE SECRET AND SPECIFIC CHEMICAL IDENTITY AND EXACT PERCENTAGE
(CONCENTRATION) OF COMPOSITION MAY HAVE BEEN WITHHELD. SPECIFIC CHEMICAL
IDENTITY AND EXACT PERCENTAGE COMPOSITION WILL BE PROVIDED TO HEALTH
PROFESSIONALS, EMPLOYEES, OR DESIGNATED REPRESENTATIVES IN ACCORDANCE
WITH APPLICABLE PROVISIONS OF PARAGRAPH (I).
| SECTION 4 FIRST AID MEASURES | |
INHALATION:
REMOVE FROM FURTHER EXPOSURE. FOR THOSE PROVIDING ASSISTANCE, AVOID
EXPOSURE TO YOURSELF OR OTHERS. USE ADEQUATE RESPIRATORY PROTECTION. IF
RESPIRATORY IRRITATION, DIZZINESS, NAUSEA, OR UNCONSCIOUSNESS OCCURS,
SEEK IMMEDIATE MEDICAL ASSISTANCE. IF BREATHING HAS STOPPED, ASSIST
VENTILATION WITH A MECHANICAL DEVICE OR USE MOUTH-TO-MOUTH RESUSCITATION.
SKIN CONTACT:
WASH CONTACT AREAS WITH SOAP AND WATER. REMOVE CONTAMINATED CLOTHING.
LAUNDER CONTAMINATED CLOTHING BEFORE REUSE. IF PRODUCT IS INJECTED INTO
OR UNDER THE SKIN, OR INTO ANY PART OF THE BODY, REGARDLESS OF THE
APPEARANCE OF THE WOUND OR ITS SIZE, THE INDIVIDUAL SHOULD BE EVALUATED
IMMEDIATELY BY A PHYSICIAN AS A SURGICAL EMERGENCY. EVEN THOUGH INITIAL
SYMPTOMS FROM HIGH PRESSURE INJECTION MAY BE MINIMAL OR ABSENT, EARLY
SURGICAL TREATMENT WITHIN THE FIRST FEW HOURS MAY SIGNIFICANTLY REDUCE
THE ULTIMATE EXTENT OF INJURY.
EYE CONTACT:
FLUSH THOROUGHLY WITH WATER. IF IRRITATION OCCURS, GET MEDICAL ASSISTANCE.
INGESTION:
SEEK IMMEDIATE MEDICAL ATTENTION. DO NOT INDUCE VOMITING.
NOTE TO PHYSICIAN:
IF INGESTED, MATERIAL MAY BE ASPIRATED INTO THE LUNGS AND CAUSE CHEMICAL
PNEUMONITIS. TREAT APPROPRIATELY.
| SECTION 5 FIRE FIGHTING MEASURES | |
EXTINGUISHING MEDIA:
APPROPRIATE EXTINGUISHING MEDIA:
USE WATER FOG, FOAM, DRY CHEMICAL OR CARBON DIOXIDE (CO2) TO EXTINGUISH
FLAMES.
INAPPROPRIATE EXTINGUISHING MEDIA: STRAIGHT STREAMS OF WATER
FIRE FIGHTING:
FIRE FIGHTING INSTRUCTIONS:
EVACUATE AREA. PREVENT RUNOFF FROM FIRE CONTROL OR DILUTION FROM ENTERING
STREAMS, SEWERS, OR DRINKING WATER SUPPLY. FIREFIGHTERS SHOULD USE
STANDARD PROTECTIVE EQUIPMENT AND IN ENCLOSED SPACES, SELF-CONTAINED
BREATHING APPARATUS (SCBA). USE WATER SPRAY TO COOL FIRE EXPOSED SURFACES
AND TO PROTECT PERSONNEL.
HAZARDOUS COMBUSTION PRODUCTS:
ALDEHYDES, SULFUR OXIDES, OXIDES OF CARBON, INCOMPLETE COMBUSTION
PRODUCTS, SMOKE, FUME
FLAMMABILITY PROPERTIES:
FLASH POINT [METHOD]: >154 DEG. C (309 DEG. F) [ASTM D-92]
FLAMMABLE LIMITS (APPROXIMATE VOLUME % IN AIR):
LEL: N/D
UEL: N/D
AUTOIGNITION TEMPERATURE: N/D
| SECTION 6 ACCIDENTAL RELEASE MEASURES | |
NOTIFICATION PROCEDURES:
IN THE EVENT OF A SPILL OR ACCIDENTAL RELEASE, NOTIFY RELEVANT AUTHORITIES
IN ACCORDANCE WITH ALL APPLICABLE REGULATIONS. US REGULATIONS REQUIRE
REPORTING RELEASES OF THIS MATERIAL TO THE ENVIRONMENT WHICH EXCEED THE
APPLICABLE REPORTABLE QUANTITY OR OIL SPILLS WHICH COULD REACH ANY
WATERWAY INCLUDING INTERMITTENT DRY CREEKS. THE NATIONAL RESPONSE CENTER
CAN BE REACHED AT (800)424-8802.
PROTECTIVE MEASURES:
AVOID CONTACT WITH SPILLED MATERIAL. WARN OR EVACUATE OCCUPANTS IN
SURROUNDING AND DOWNWIND AREAS IF REQUIRED DUE TO TOXICITY OR FLAMMABILITY
OF THE MATERIAL. SEE SECTION 5 FOR FIRE FIGHTING INFORMATION. SEE THE
HAZARD IDENTIFICATION SECTION FOR SIGNIFICANT HAZARDS. SEE SECTION 4 FOR
FIRST AID ADVICE. SEE SECTION 8 FOR ADVICE ON THE MINIMUM REQUIREMENTS FOR
PERSONAL PROTECTIVE EQUIPMENT. ADDITIONAL PROTECTIVE MEASURES MAY BE
NECESSARY, DEPENDING ON THE SPECIFIC CIRCUMSTANCES AND/OR THE EXPERT
JUDGMENT OF THE EMERGENCY RESPONDERS.
FOR EMERGENCY RESPONDERS:
RESPIRATORY PROTECTION:
RESPIRATORY PROTECTION WILL BE NECESSARY ONLY IN SPECIAL CASES, E.G.,
FORMATION OF MISTS. HALF-FACE OR FULL-FACE RESPIRATOR WITH FILTER(S) FOR
DUST/ORGANIC VAPOR OR SELF CONTAINED BREATHING APPARATUS (SCBA) CAN BE
USED DEPENDING ON THE SIZE OF SPILL AND POTENTIAL LEVEL OF EXPOSURE. IF
THE EXPOSURE CANNOT BE COMPLETELY CHARACTERIZED OR AN OXYGEN DEFICIENT
ATMOSPHERE IS POSSIBLE OR ANTICIPATED, SCBA IS RECOMMENDED. WORK GLOVES
THAT ARE RESISTANT TO HYDROCARBONS ARE RECOMMENDED. GLOVES MADE OF
POLYVINYL ACETATE (PVA) ARE NOT WATER-RESISTANT AND ARE NOT SUITABLE FOR
EMERGENCY USE. CHEMICAL GOGGLES ARE RECOMMENDED IF SPLASHES OR CONTACT
WITH EYES IS POSSIBLE. SMALL SPILLS: NORMAL ANTISTATIC WORK CLOTHES ARE
USUALLY ADEQUATE. LARGE SPILLS: FULL BODY SUIT OF CHEMICAL RESISTANT,
ANTISTATIC MATERIAL IS RECOMMENDED.
SPILL MANAGEMENT:
LAND SPILL:
STOP LEAK IF YOU CAN DO IT WITHOUT RISK. ABSORB OR COVER WITH DRY EARTH,
SAND OR OTHER NON-COMBUSTIBLE MATERIAL AND TRANSFER TO CONTAINERS.
WATER SPILL:
STOP LEAK IF YOU CAN DO IT WITHOUT RISK. CONFINE THE SPILL IMMEDIATELY
WITH BOOMS. WARN OTHER SHIPPING. REMOVE FROM THE SURFACE BY SKIMMING OR
WITH SUITABLE ABSORBENTS. SEEK THE ADVICE OF A SPECIALIST BEFORE USING
DISPERSANTS.
WATER SPILL AND LAND SPILL RECOMMENDATIONS ARE BASED ON THE MOST LIKELY
SPILL SCENARIO FOR THIS MATERIAL; HOWEVER, GEOGRAPHIC CONDITIONS, WIND,
TEMPERATURE, (AND IN THE CASE OF A WATER SPILL) WAVE AND CURRENT DIRECTION
AND SPEED MAY GREATLY INFLUENCE THE APPROPRIATE ACTION TO BE TAKEN. FOR
THIS REASON, LOCAL EXPERTS SHOULD BE CONSULTED.
NOTE: LOCAL REGULATIONS MAY PRESCRIBE OR LIMIT ACTION TO BE TAKEN.
ENVIRONMENTAL PRECAUTIONS:
LARGE SPILLS:
DIKE FAR AHEAD OF LIQUID SPILL FOR LATER RECOVERY AND DISPOSAL. PREVENT
ENTRY INTO WATERWAYS, SEWERS, BASEMENTS OR CONFINED AREAS.
| SECTION 7 HANDLING AND STORAGE | |
HANDLING:
AVOID CONTACT WITH SKIN. PREVENT SMALL SPILLS AND LEAKAGE TO AVOID SLIP
HAZARD. MATERIAL CAN ACCUMULATE STATIC CHARGES WHICH MAY CAUSE AN
ELECTRICAL SPARK (IGNITION SOURCE). WHEN THE MATERIAL IS HANDLED IN BULK,
AN ELECTRICAL SPARK COULD IGNITE ANY FLAMMABLE VAPORS FROM LIQUIDS OR
RESIDUES THAT MAY BE PRESENT (E.G., DURING SWITCH-LOADING OPERATIONS). USE
PROPER BONDING AND/OR GROUND PROCEDURES. HOWEVER, BONDING AND GROUNDS MAY
NOT ELIMINATE THE HAZARD FROM STATIC ACCUMULATION. CONSULT LOCAL
APPLICABLE STANDARDS FOR GUIDANCE. ADDITIONAL REFERENCES INCLUDE AMERICAN
PETROLEUM INSTITUTE 2003 (PROTECTION AGAINST IGNITIONS ARISING OUT OF
STATIC, LIGHTNING AND STRAY CURRENTS) OR NATIONAL FIRE PROTECTION AGENCY
77 (RECOMMENDED PRACTICE ON STATIC ELECTRICITY) OR CENELEC CLC/TR 50404
(ELECTROSTATICS - CODE OF PRACTICE FOR THE AVOIDANCE OF HAZARDS DUE TO
STATIC ELECTRICITY).
STATIC ACCUMULATOR: THIS MATERIAL IS A STATIC ACCUMULATOR.
STORAGE:
THE CONTAINER CHOICE, FOR EXAMPLE STORAGE VESSEL, MAY EFFECT STATIC
ACCUMULATION AND DISSIPATION. DO NOT STORE IN OPEN OR UNLABELLED
CONTAINERS.
| SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION | |
EXPOSURE LIMIT VALUES:
EXPOSURE LIMITS/STANDARDS (NOTE: EXPOSURE LIMITS ARE NOT ADDITIVE):
SUBSTANCE NAME FORM LIMIT / STANDARD NOTE SOURCE
SOLVENT REFINED MIST. TWA 5 MG/M3 N/A OSHA Z1
LIGHT PARAFFINIC
DISTILLATE
(PETROLEUM)
SOLVENT REFINED INHALABLE TWA 5 MG/M3 N/A ACGIH
LIGHT PARAFFINIC FRACTION.
DISTILLATE
(PETROLEUM)
SOLVENT REFINED MIST. TWA 5 MG/M3 N/A ACGIH
LIGHT PARAFFINIC
DISTILLATE
(PETROLEUM)
STRAIGHT-RUN STABLE TWA 5 MG/M3 N/A EXXONMOBIL
MIDDLE AEROSOL.
DISTILLATES
STRAIGHT-RUN VAPOR. TWA 200 MG/M3 N/A EXXONMOBIL
MIDDLE
DISTILLATES
EXPOSURE LIMITS/STANDARDS FOR MATERIALS THAT CAN BE FORMED WHEN HANDLING
THIS PRODUCT:
WHEN MISTS/AEROSOLS CAN OCCUR THE FOLLOWING ARE RECOMMENDED:
5 MG/M3 - ACGIH TLV (INHALABLE FRACTION), 5 MG/M3 - OSHA PEL.
NOTE:
LIMITS/STANDARDS SHOWN FOR GUIDANCE ONLY. FOLLOW APPLICABLE REGULATIONS.
NO BIOLOGICAL LIMITS ALLOCATED.
ENGINEERING CONTROLS:
THE LEVEL OF PROTECTION AND TYPES OF CONTROLS NECESSARY WILL VARY
DEPENDING UPON POTENTIAL EXPOSURE CONDITIONS. CONTROL MEASURES TO
CONSIDER:
ADEQUATE VENTILATION SHOULD BE PROVIDED SO THAT EXPOSURE LIMITS ARE NOT
EXCEEDED.
PERSONAL PROTECTION:
PERSONAL PROTECTIVE EQUIPMENT SELECTIONS VARY BASED ON POTENTIAL EXPOSURE
CONDITIONS SUCH AS APPLICATIONS, HANDLING PRACTICES, CONCENTRATION AND
VENTILATION. INFORMATION ON THE SELECTION OF PROTECTIVE EQUIPMENT FOR USE
WITH THIS MATERIAL, AS PROVIDED BELOW, IS BASED UPON INTENDED, NORMAL
USAGE.
RESPIRATORY PROTECTION:
IF ENGINEERING CONTROLS DO NOT MAINTAIN AIRBORNE CONTAMINANT
CONCENTRATIONS AT A LEVEL WHICH IS ADEQUATE TO PROTECT WORKER HEALTH, AN
APPROVED RESPIRATOR MAY BE APPROPRIATE. RESPIRATOR SELECTION, USE, AND
MAINTENANCE MUST BE IN ACCORDANCE WITH REGULATORY REQUIREMENTS, IF
APPLICABLE. TYPES OF RESPIRATORS TO BE CONSIDERED FOR THIS MATERIAL
INCLUDE:
NO SPECIAL REQUIREMENTS UNDER ORDINARY CONDITIONS OF USE AND WITH
ADEQUATE VENTILATION.
FOR HIGH AIRBORNE CONCENTRATIONS, USE AN APPROVED SUPPLIED-AIR RESPIRATOR,
OPERATED IN POSITIVE PRESSURE MODE. SUPPLIED AIR RESPIRATORS WITH AN
ESCAPE BOTTLE MAY BE APPROPRIATE WHEN OXYGEN LEVELS ARE INADEQUATE,
GAS/VAPOR WARNING PROPERTIES ARE POOR, OR IF AIR PURIFYING FILTER
CAPACITY/RATING MAY BE EXCEEDED.
HAND PROTECTION:
ANY SPECIFIC GLOVE INFORMATION PROVIDED IS BASED ON PUBLISHED LITERATURE
AND GLOVE MANUFACTURER DATA. GLOVE SUITABILITY AND BREAKTHROUGH TIME WILL
DIFFER DEPENDING ON THE SPECIFIC USE CONDITIONS. CONTACT THE GLOVE
MANUFACTURER FOR SPECIFIC ADVICE ON GLOVE SELECTION AND BREAKTHROUGH
TIMES FOR YOUR USE CONDITIONS. INSPECT AND REPLACE WORN OR DAMAGED
GLOVES. THE TYPES OF GLOVES TO BE CONSIDERED FOR THIS MATERIAL INCLUDE:
IF PROLONGED OR REPEATED CONTACT IS LIKELY, CHEMICAL RESISTANT GLOVES ARE
RECOMMENDED. IF CONTACT WITH FOREARMS IS LIKELY, WEAR GAUNTLET STYLE
GLOVES.
EYE PROTECTION:
IF CONTACT IS LIKELY, SAFETY GLASSES WITH SIDE SHIELDS ARE RECOMMENDED.
SKIN AND BODY PROTECTION:
ANY SPECIFIC CLOTHING INFORMATION PROVIDED IS BASED ON PUBLISHED
LITERATURE OR MANUFACTURER DATA. THE TYPES OF CLOTHING TO BE CONSIDERED
FOR THIS MATERIAL INCLUDE:
IF PROLONGED OR REPEATED CONTACT IS LIKELY, CHEMICAL, AND OIL RESISTANT
CLOTHING IS RECOMMENDED.
SPECIFIC HYGIENE MEASURES:
ALWAYS OBSERVE GOOD PERSONAL HYGIENE MEASURES, SUCH AS WASHING AFTER
HANDLING THE MATERIAL AND BEFORE EATING, DRINKING, AND/OR SMOKING.
ROUTINELY WASH WORK CLOTHING AND PROTECTIVE EQUIPMENT TO REMOVE
CONTAMINANTS. DISCARD CONTAMINATED CLOTHING AND FOOTWEAR THAT CANNOT
BE CLEANED. PRACTICE GOOD HOUSEKEEPING.
ENVIRONMENTAL CONTROLS:
COMPLY WITH APPLICABLE ENVIRONMENTAL REGULATIONS LIMITING DISCHARGE
TO AIR, WATER AND SOIL. PROTECT THE ENVIRONMENT BY APPLYING APPROPRIATE
CONTROL MEASURES TO PREVENT OR LIMIT EMISSIONS.
| SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES | |
NOTE:
PHYSICAL AND CHEMICAL PROPERTIES ARE PROVIDED FOR SAFETY, HEALTH AND
ENVIRONMENTAL CONSIDERATIONS ONLY AND MAY NOT FULLY REPRESENT PRODUCT
SPECIFICATIONS. CONTACT THE SUPPLIER FOR ADDITIONAL INFORMATION.
GENERAL INFORMATION:
PHYSICAL STATE: LIQUID
COLOR: PALE YELLOW
ODOR: CHARACTERISTIC
ODOR THRESHOLD: N/D
IMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATION:
RELATIVE DENSITY (AT 15 DEG. C): 0.844
FLAMMABILITY (SOLID, GAS): N/A
FLASH POINT [METHOD]: >154 DEG. C (309 DEG. F) [ASTM D-92]
FLAMMABLE LIMITS (APPROXIMATE VOLUME % IN AIR):
LEL: N/D
UEL: N/D
AUTOIGNITION TEMPERATURE: N/D
BOILING POINT / RANGE: N/D
DECOMPOSITION TEMPERATURE: N/D
VAPOR DENSITY (AIR = 1): >2 AT 101 KPA [ESTIMATED]
VAPOR PRESSURE: <0.013 KPA (0.1 MMHg) AT 20 DEG. C [ESTIMATED]
EVAPORATION RATE (N-BUTYL ACETATE = 1): N/D
PH: N/A
LOG POW (N-OCTANOL/WATER PARTITION COEFFICIENT): >3.5 [ESTIMATED]
SOLUBILITY IN WATER: NEGLIGIBLE
VISCOSITY: 9.3 CST (9.3 MM2/SEC) AT 40 DEG. C
OXIDIZING PROPERTIES: SEE HAZARDS IDENTIFICATION SECTION.
OTHER INFORMATION:
FREEZING POINT: N/D
MELTING POINT: N/A
POUR POINT: -12 DEG. C (10 DEG. F)
DMSO EXTRACT (MINERAL OIL ONLY), IP-346: <3 %WT
| SECTION 10 STABILITY AND REACTIVITY | |
REACTIVITY: SEE SUB-SECTIONS BELOW.
STABILITY: MATERIAL IS STABLE UNDER NORMAL CONDITIONS.
CONDITIONS TO AVOID: EXCESSIVE HEAT. HIGH ENERGY SOURCES OF IGNITION.
MATERIALS TO AVOID: STRONG OXIDIZERS
HAZARDOUS DECOMPOSITION PRODUCTS:
MATERIAL DOES NOT DECOMPOSE AT AMBIENT TEMPERATURES.
POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
| SECTION 11 TOXICOLOGICAL INFORMATION | |
INFORMATION ON TOXICOLOGICAL EFFECTS:
HAZARD CLASS CONCLUSION / REMARKS
INHALATION:
ACUTE TOXICITY:
NO END POINT DATA FOR MATERIAL. MINIMALLY TOXIC. BASED ON ASSESSMENT
OF THE COMPONENTS.
IRRITATION:
NO END POINT DATA FOR MATERIAL. ELEVATED TEMPERATURES OR MECHANICAL
ACTION MAY FORM VAPORS, MIST, OR
FUMES WHICH MAY BE IRRITATING TO THE
EYES, NOSE, THROAT, OR LUNGS.
INGESTION:
ACUTE TOXICITY:
NO END POINT DATA FOR MATERIAL. MINIMALLY TOXIC. BASED ON ASSESSMENT
OF THE COMPONENTS.
SKIN:
ACUTE TOXICITY:
NO END POINT DATA FOR MATERIAL. MINIMALLY TOXIC. BASED ON ASSESSMENT
OF THE COMPONENTS.
SKIN CORROSION/IRRITATION:
NO END POINT DATA FOR MATERIAL. NEGLIGIBLE IRRITATION TO SKIN AT
AMBIENT TEMPERATURES. BASED ON
ASSESSMENT OF THE COMPONENTS.
EYE:
SERIOUS EYE DAMAGE/IRRITATION:
NO END POINT DATA FOR MATERIAL. MAY CAUSE MILD, SHORT-LASTING
DISCOMFORT TO EYES. BASED ON
ASSESSMENT OF THE COMPONENTS.
SENSITIZATION:
RESPIRATORY SENSITIZATION: NOT EXPECTED TO BE A RESPIRATORY
SENSITIZER.
SKIN SENSITIZATION: NOT EXPECTED TO BE A SKIN
SENSITIZER.
ASPIRATION: MAY BE FATAL IF SWALLOWED AND ENTERS
AIRWAYS. BASED ON PHYSICO-CHEMICAL
PROPERTIES OF THE MATERIAL.
GERM CELL MUTAGENICITY: NOT EXPECTED TO BE A GERM CELL
MUTAGEN.
CARCINOGENICITY: NOT EXPECTED TO CAUSE CANCER.
REPRODUCTIVE TOXICITY: NOT EXPECTED TO BE A REPRODUCTIVE
TOXICANT.
LACTATION: NOT EXPECTED TO CAUSE HARM TO
BREAST-FED CHILDREN.
SPECIFIC TARGET ORGAN TOXICITY
(STOT):
SINGLE EXPOSURE: NOT EXPECTED TO CAUSE ORGAN DAMAGE
FROM A SINGLE EXPOSURE.
REPEATED EXPOSURE: NOT EXPECTED TO CAUSE ORGAN DAMAGE
FROM PROLONGED OR REPEATED EXPOSURE.
OTHER INFORMATION:
FOR THE PRODUCT ITSELF:
SMALL AMOUNTS OF LIQUID ASPIRATED INTO THE LUNGS DURING INGESTION OR FROM
VOMITING MAY CAUSE CHEMICAL PNEUMONITIS OR PULMONARY EDEMA.
THE FOLLOWING INGREDIENTS ARE CITED ON THE LISTS BELOW: NONE.
REGULATORY LISTS SEARCHED:
1 = NTP CARC
2 = NTP SUS
3 = IARC 1
4 = IARC 2A
5 = IARC 2B
6 = OSHA CARC
| SECTION 12 ECOLOGICAL INFORMATION | |
THE INFORMATION GIVEN IS BASED ON DATA AVAILABLE FOR THE MATERIAL,
THE COMPONENTS OF THE MATERIAL, AND SIMILAR MATERIALS.
ECOTOXICITY:
MATERIAL:
EXPECTED TO BE HARMFUL TO AQUATIC ORGANISMS. MAY CAUSE LONG-TERM ADVERSE
EFFECTS IN THE AQUATIC ENVIRONMENT.
MOBILITY:
MORE VOLATILE COMPONENT:
HIGHLY VOLATILE, WILL PARTITION RAPIDLY TO AIR. NOT EXPECTED TO PARTITION
TO SEDIMENT AND WASTEWATER SOLIDS.
MAJORITY OF COMPONENTS:
LOW SOLUBILITY AND FLOATS AND IS EXPECTED TO MIGRATE FROM WATER TO THE
LAND. EXPECTED TO PARTITION TO SEDIMENT AND WASTEWATER SOLIDS.
PERSISTENCE AND DEGRADABILITY:
BIODEGRADATION:
MAJORITY OF COMPONENTS: EXPECTED TO BE INHERENTLY BIODEGRADABLE
ATMOSPHERIC OXIDATION:
MORE VOLATILE COMPONENT: EXPECTED TO DEGRADE RAPIDLY IN AIR
BIOACCUMULATION POTENTIAL:
MAJORITY OF COMPONENTS:
HAS THE POTENTIAL TO BIOACCUMULATE, HOWEVER METABOLISM OR PHYSICAL
PROPERTIES MAY REDUCE THE BIOCONCENTRATION OR LIMIT BIOAVAILABILITY.
OTHER ECOLOGICAL INFORMATION:
VOC: 14.2 G/L [ASTM E1868-10]
| SECTION 13 DISPOSAL CONSIDERATIONS | |
DISPOSAL RECOMMENDATIONS BASED ON MATERIAL AS SUPPLIED. DISPOSAL MUST BE
IN ACCORDANCE WITH CURRENT APPLICABLE LAWS AND REGULATIONS, AND MATERIAL
CHARACTERISTICS AT TIME OF DISPOSAL.
DISPOSAL RECOMMENDATIONS:
PRODUCT IS SUITABLE FOR BURNING IN AN ENCLOSED CONTROLLED BURNER FOR FUEL
VALUE OR DISPOSAL BY SUPERVISED INCINERATION AT VERY HIGH TEMPERATURES TO
PREVENT FORMATION OF UNDESIRABLE COMBUSTION PRODUCTS. PROTECT THE
ENVIRONMENT. DISPOSE OF USED OIL AT DESIGNATED SITES. MINIMIZE SKIN
CONTACT. DO NOT MIX USED OILS WITH SOLVENTS, BRAKE FLUIDS OR COOLANTS.
REGULATORY DISPOSAL INFORMATION:
RCRA INFORMATION:
THE UNUSED PRODUCT, IN OUR OPINION, IS NOT SPECIFICALLY LISTED BY THE EPA
AS A HAZARDOUS WASTE (40 CFR, PART 261D), NOR IS IT FORMULATED TO CONTAIN
MATERIALS WHICH ARE LISTED AS HAZARDOUS WASTES. IT DOES NOT EXHIBIT THE
HAZARDOUS CHARACTERISTICS OF IGNITABILITY, CORROSITIVITY OR REACTIVITY AND
IS NOT FORMULATED WITH CONTAMINANTS AS DETERMINED BY THE TOXICITY
CHARACTERISTIC LEACHING PROCEDURE (TCLP). HOWEVER, USED PRODUCT MAY BE
REGULATED.
EMPTY CONTAINER WARNING:
EMPTY CONTAINER WARNING (WHERE APPLICABLE):
EMPTY CONTAINERS MAY CONTAIN RESIDUE AND CAN BE DANGEROUS. DO NOT ATTEMPT
TO REFILL OR CLEAN CONTAINERS WITHOUT PROPER INSTRUCTIONS. EMPTY DRUMS
SHOULD BE COMPLETELY DRAINED AND SAFELY STORED UNTIL APPROPRIATELY
RECONDITIONED OR DISPOSED. EMPTY CONTAINERS SHOULD BE TAKEN FOR RECYCLING,
RECOVERY, OR DISPOSAL THROUGH SUITABLY QUALIFIED OR LICENSED CONTRACTOR
AND IN ACCORDANCE WITH GOVERNMENTAL REGULATIONS. DO NOT PRESSURISE, CUT,
WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE SUCH CONTAINERS TO HEAT,
FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION. THEY
MAY EXPLODE AND CAUSE INJURY OR DEATH.
| SECTION 14 TRANSPORT INFORMATION | |
LAND (DOT): NOT REGULATED FOR LAND TRANSPORT
LAND (TDG): NOT REGULATED FOR LAND TRANSPORT
SEA (IMDG): NOT REGULATED FOR SEA TRANSPORT ACCORDING TO IMDG-CODE
MARINE POLLUTANT: NO
AIR (IATA): NOT REGULATED FOR AIR TRANSPORT
| SECTION 15 REGULATORY INFORMATION | |
OSHA HAZARD COMMUNICATION STANDARD:
THIS MATERIAL IS CONSIDERED HAZARDOUS IN ACCORDANCE WITH OSHA HAZCOM 2012,
29 CFR 1910.1200.
LISTED OR EXEMPT FROM LISTING/NOTIFICATION ON THE FOLLOWING CHEMICAL
INVENTORIES:
AICS, DSL, ENCS, IECSC, KECI, PICCS, TSCA
EPCRA SECTION 302:
THIS MATERIAL CONTAINS NO EXTREMELY HAZARDOUS SUBSTANCES.
SARA (311/312) REPORTABLE HAZARD CATEGORIES: DELAYED HEALTH.
SARA (313) TOXIC RELEASE INVENTORY:
THIS MATERIAL CONTAINS NO CHEMICALS SUBJECT TO THE SUPPLIER NOTIFICATION
REQUIREMENTS OF THE SARA 313 TOXIC RELEASE PROGRAM.
THE FOLLOWING INGREDIENTS ARE CITED ON THE LISTS BELOW:
CHEMICAL NAME CAS NUMBER LIST CITATIONS
SOLVENT REFINED LIGHT PARAFFINIC 64741-89-5 1, 4, 17, 18
DISTILLATE (PETROLEUM)
REGULATORY LISTS SEARCHED:
1 = ACGIH ALL
2 = ACGIH A1
3 = ACGIH A2
4 = OSHA Z
5 = TSCA 4
6 = TSCA 5A2
7 = TSCA 5E
8 = TSCA 6
9 = TSCA 12B
10 = CA P65 CARC
11 = CA P65 REPRO
12 = CA RTK
13 = IL RTK
14 = LA RTK
15 = MI 293
16 = MN RTK
17 = NJ RTK
18 = PA RTK
19 = RI RTK
CODE KEY:
CARC=CARCINOGEN;
REPRO=REPRODUCTIVE
| SECTION 16 OTHER INFORMATION | |
N/D = NOT DETERMINED,
N/A = NOT APPLICABLE
KEY TO THE H-CODES CONTAINED IN SECTION 3 OF THIS DOCUMENT (FOR
INFORMATION ONLY):
H304: MAY BE FATAL IF SWALLOWED AND ENTERS AIRWAYS; ASPIRATION, CAT 1
H315: CAUSES SKIN IRRITATION; SKIN CORR/IRRITATION, CAT 2
H319(2A): CAUSES SERIOUS EYE IRRITATION; SERIOUS EYE DAMAGE/IRR, CAT 2A
H400: VERY TOXIC TO AQUATIC LIFE; ACUTE ENV TOX, CAT 1
H401: TOXIC TO AQUATIC LIFE; ACUTE ENV TOX, CAT 2
H410:
VERY TOXIC TO AQUATIC LIFE WITH LONG LASTING EFFECTS; CHRONIC ENV TOX,
CAT 1
H411:
TOXIC TO AQUATIC LIFE WITH LONG LASTING EFFECTS; CHRONIC ENV TOX, CAT 2
THIS SAFETY DATA SHEET CONTAINS THE FOLLOWING REVISIONS:
UPDATES MADE IN ACCORDANCE WITH IMPLEMENTATION OF GHS REQUIREMENTS.
THE INFORMATION AND RECOMMENDATIONS CONTAINED HEREIN ARE, TO THE BEST OF
EXXONMOBIL'S KNOWLEDGE AND BELIEF, ACCURATE AND RELIABLE AS OF THE DATE
ISSUED. YOU CAN CONTACT EXXONMOBIL TO INSURE THAT THIS DOCUMENT IS THE
MOST CURRENT AVAILABLE FROM EXXONMOBIL. THE INFORMATION AND
RECOMMENDATIONS ARE OFFERED FOR THE USER'S CONSIDERATION AND EXAMINATION.
IT IS THE USER'S RESPONSIBILITY TO SATISFY ITSELF THAT THE PRODUCT IS
SUITABLE FOR THE INTENDED USE. IF BUYER REPACKAGES THIS PRODUCT, IT IS
THE USER'S RESPONSIBILITY TO INSURE PROPER HEALTH, SAFETY AND OTHER
NECESSARY INFORMATION IS INCLUDED WITH AND/OR ON THE CONTAINER.
APPROPRIATE WARNINGS AND SAFE-HANDLING PROCEDURES SHOULD BE PROVIDED TO
HANDLERS AND USERS. ALTERATION OF THIS DOCUMENT IS STRICTLY PROHIBITED.
EXCEPT TO THE EXTENT REQUIRED BY LAW, RE-PUBLICATION OR RETRANSMISSION OF
THIS DOCUMENT, IN WHOLE OR IN PART, IS NOT PERMITTED. THE TERM,
"EXXONMOBIL" IS USED FOR CONVENIENCE, AND MAY INCLUDE ANY ONE OR MORE OF
EXXONMOBIL CHEMICAL COMPANY, EXXON MOBIL CORPORATION, OR ANY AFFILIATES
IN WHICH THEY DIRECTLY OR INDIRECTLY HOLD ANY INTEREST.
INTERNAL USE ONLY:
MHC: 2A, 0, 0, 0, 0, 1
PPEC: C
DGN: 2007289XUS (553809)
COPYRIGHT 2002 EXXON MOBIL CORPORATION, ALL RIGHTS RESERVED