| Common Name: | MOBILCUT 100 |
| Manufacturer: | EXXON MOBIL |
| SDS Revision Date: | 3/16/2015 |
| SDS Format: | GHS-US |
| Item Number(s): | 4FVD9 |
| Manufacturer Model Number(s): |
SDS Table of Contents
Click the desired link below to jump directly to that section in the SDS.
EXXON MOBIL
PRODUCT NAME: MOBILCUT 100
REVISION DATE: 16 MAR 2015
SAFETY DATA SHEET
| SECTION 1 PRODUCT AND COMPANY IDENTIFICATION |  |
PRODUCT:
PRODUCT NAME: MOBILCUT 100
PRODUCT DESCRIPTION: BASE OIL AND ADDITIVES
PRODUCT CODE: 2015703010I5, 662106-00, 97BT26
INTENDED USE: WATER-MISCIBLE CUTTING FLUID
COMPANY IDENTIFICATION:
SUPPLIER:
EXXON MOBIL CORPORATION
22777 SPRINGWOODS VILLAGE PARKWAY
SPRING, TX. 77389
USA
24 HOUR HEALTH EMERGENCY: 609-737-4411
TRANSPORTATION EMERGENCY PHONE: 800-424-9300 OR 703-527-3887 CHEMTREC
PRODUCT TECHNICAL INFORMATION: 800-662-4525
MSDS INTERNET ADDRESS:
HTTP://WWW.EXXON.COM
HTTP://WWW.MOBIL.COM
| SECTION 2 HAZARDS IDENTIFICATION | |
THIS MATERIAL IS HAZARDOUS ACCORDING TO REGULATORY GUIDELINES (SEE (M)SDS
SECTION 15).
CLASSIFICATION:
SKIN SENSITIZER: CATEGORY 1.
LABEL:
PICTOGRAM: EXCLAMATION MARK
SIGNAL WORD: WARNING
HAZARD STATEMENTS:
H317: MAY CAUSE ALLERGIC SKIN REACTION.
PRECAUTIONARY STATEMENTS:
P261: AVOID BREATHING MIST / VAPOURS.
P272:
CONTAMINATED WORK CLOTHING SHOULD NOT BE ALLOWED OUT OF THE WORKPLACE.
P273: AVOID RELEASE TO THE ENVIRONMENT.
P302 + P352:
IF ON SKIN: WASH WITH PLENTY OF SOAP AND WATER.
P333 + P313:
IF SKIN IRRITATION OR RASH OCCURS: GET MEDICAL ADVICE/ATTENTION.
P362 + P364: TAKE OFF CONTAMINATED CLOTHING AND WASH IT BEFORE REUSE.
P501:
DISPOSE OF CONTENTS AND CONTAINER IN ACCORDANCE WITH LOCAL REGULATIONS.
CONTAINS: OXAZOLIDINE
OTHER HAZARD INFORMATION:
HAZARD NOT OTHERWISE CLASSIFIED (HNOC):
NONE AS DEFINED UNDER 29 CFR 1910.1200.
PHYSICAL / CHEMICAL HAZARDS: NO SIGNIFICANT HAZARDS.
HEALTH HAZARDS:
HIGH-PRESSURE INJECTION UNDER SKIN MAY CAUSE SERIOUS DAMAGE. THIS PRODUCT
MAY BE USED IN CERTAIN APPLICATIONS WHERE MISTING CAN OCCUR. EXCESSIVE
EXPOSURE TO LIQUIDS AND MISTS MAY CAUSE SKIN AND EYE IRRITATION. IN
ADDITION, EXCESSIVE EXPOSURE TO MISTS MAY CAUSE RESPIRATORY IRRITATION
AND DAMAGE AND AGGRAVATE PRE-EXISTING EMPHYSEMA OR ASTHMA.
ENVIRONMENTAL HAZARDS: EXPECTED TO BE HARMFUL TO AQUATIC ORGANISMS.
NFPA HAZARD ID:
HEALTH 2
FLAMMABILITY 1
REACTIVITY 0
HMIS HAZARD ID:
HEALTH 2
FLAMMABILITY 1
REACTIVITY 0
NOTE:
THIS MATERIAL SHOULD NOT BE USED FOR ANY OTHER PURPOSE THAN THE INTENDED
USE IN SECTION 1 WITHOUT EXPERT ADVICE. HEALTH STUDIES HAVE SHOWN THAT
CHEMICAL EXPOSURE MAY CAUSE POTENTIAL HUMAN HEALTH RISKS WHICH MAY VARY
FROM PERSON TO PERSON.
| SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTS | |
THIS MATERIAL IS DEFINED AS A MIXTURE.
HAZARDOUS SUBSTANCE(S) OR COMPLEX SUBSTANCE(S) REQUIRED FOR DISCLOSURE:
NAME CAS# CONCENTRATION* GHS HAZARD
CODES
1H, 3H, 5H - OXAZOLO 7747-35-5 0.1 - <1% H315, H318, H317
(3,4,-C) OXAZOLE,
7A-ETHYLDIHYDRO-
ALCOHOLS, C12-15 68131-39-5 0.1 - <1% H302, H318, H400
ETHOXYLATED (M FACTOR 1)
FATTY ACIDS, TALL-OIL 68953-28-6 1 - <5% H315, H319(2A)
COMPOUNDS WITH
DIISOPRPANOLAMINE
SEVERELY HYDROTREATED 64742-54-7 40 - <50% H304
HEAVY PARAFFINIC
DISTILLATE
SODIUM PETROLEUM 68608-26-4 1 - <5% H318
SULFONATE
SOLVENT DEWAXED HEAVY 64742-65-0 40 - <50% H304
PARAFFINIC DISTILLATE
TALL OIL ACIDS AND CONFIDENTIAL 1 - <5% H319(2A)
NAPHTHENIC ACIDS,
POTASSIUM SALTS
* ALL CONCENTRATIONS ARE PERCENT BY WEIGHT UNLESS MATERIAL IS A GAS.
GAS CONCENTRATIONS ARE IN PERCENT BY VOLUME.
AS PER PARAGRAPH (I) OF 29 CFR 1910.1200, FORMULATION IS CONSIDERED
A TRADE SECRET AND SPECIFIC CHEMICAL IDENTITY AND EXACT PERCENTAGE
(CONCENTRATION) OF COMPOSITION MAY HAVE BEEN WITHHELD. SPECIFIC CHEMICAL
IDENTITY AND EXACT PERCENTAGE COMPOSITION WILL BE PROVIDED TO HEALTH
PROFESSIONALS, EMPLOYEES, OR DESIGNATED REPRESENTATIVES IN ACCORDANCE
WITH APPLICABLE PROVISIONS OF PARAGRAPH (I).
| SECTION 4 FIRST AID MEASURES | |
INHALATION:
REMOVE FROM FURTHER EXPOSURE. FOR THOSE PROVIDING ASSISTANCE, AVOID
EXPOSURE TO YOURSELF OR OTHERS. USE ADEQUATE RESPIRATORY PROTECTION.
IF RESPIRATORY IRRITATION, DIZZINESS, NAUSEA, OR UNCONSCIOUSNESS OCCURS,
SEEK IMMEDIATE MEDICAL ASSISTANCE. IF BREATHING HAS STOPPED, ASSIST
VENTILATION WITH A MECHANICAL DEVICE OR USE MOUTH-TO-MOUTH RESUSCITATION.
SKIN CONTACT:
WASH CONTACT AREAS WITH SOAP AND WATER. REMOVE CONTAMINATED CLOTHING.
LAUNDER CONTAMINATED CLOTHING BEFORE REUSE. IF PRODUCT IS INJECTED INTO
OR UNDER THE SKIN, OR INTO ANY PART OF THE BODY, REGARDLESS OF THE
APPEARANCE OF THE WOUND OR ITS SIZE, THE INDIVIDUAL SHOULD BE EVALUATED
IMMEDIATELY BY A PHYSICIAN AS A SURGICAL EMERGENCY. EVEN THOUGH INITIAL
SYMPTOMS FROM HIGH PRESSURE INJECTION MAY BE MINIMAL OR ABSENT, EARLY
SURGICAL TREATMENT WITHIN THE FIRST FEW HOURS MAY SIGNIFICANTLY REDUCE
THE ULTIMATE EXTENT OF INJURY.
EYE CONTACT:
FLUSH THOROUGHLY WITH WATER. IF IRRITATION OCCURS, GET MEDICAL ASSISTANCE.
INGESTION:
FIRST AID IS NORMALLY NOT REQUIRED. SEEK MEDICAL ATTENTION IF DISCOMFORT
OCCURS.
| SECTION 5 FIRE FIGHTING MEASURES | |
EXTINGUISHING MEDIA:
APPROPRIATE EXTINGUISHING MEDIA:
USE WATER FOG, FOAM, DRY CHEMICAL OR CARBON DIOXIDE (CO2) TO EXTINGUISH
FLAMES.
INAPPROPRIATE EXTINGUISHING MEDIA: STRAIGHT STREAMS OF WATER
FIRE FIGHTING:
FIRE FIGHTING INSTRUCTIONS:
EVACUATE AREA. PREVENT RUNOFF FROM FIRE CONTROL OR DILUTION FROM ENTERING
STREAMS, SEWERS, OR DRINKING WATER SUPPLY. FIREFIGHTERS SHOULD USE
STANDARD PROTECTIVE EQUIPMENT AND IN ENCLOSED SPACES, SELF-CONTAINED
BREATHING APPARATUS (SCBA). USE WATER SPRAY TO COOL FIRE EXPOSED SURFACES
AND TO PROTECT PERSONNEL.
UNUSUAL FIRE HAZARDS: PRESSURIZED MISTS MAY FORM A FLAMMABLE MIXTURE.
HAZARDOUS COMBUSTION PRODUCTS:
ALDEHYDES, INCOMPLETE COMBUSTION PRODUCTS, SMOKE, FUME, OXIDES OF CARBON,
SULFUR OXIDES
FLAMMABILITY PROPERTIES:
FLASH POINT [METHOD]: >179 DEG. C (354 DEG. F) [ASTM D-92]
FLAMMABLE LIMITS (APPROXIMATE VOLUME % IN AIR):
LEL: N/D
UEL: N/D
AUTOIGNITION TEMPERATURE: N/D
| SECTION 6 ACCIDENTAL RELEASE MEASURES | |
NOTIFICATION PROCEDURES:
IN THE EVENT OF A SPILL OR ACCIDENTAL RELEASE, NOTIFY RELEVANT AUTHORITIES
IN ACCORDANCE WITH ALL APPLICABLE REGULATIONS. US REGULATIONS REQUIRE
REPORTING RELEASES OF THIS MATERIAL TO THE ENVIRONMENT WHICH EXCEED THE
APPLICABLE REPORTABLE QUANTITY OR OIL SPILLS WHICH COULD REACH ANY
WATERWAY INCLUDING INTERMITTENT DRY CREEKS. THE NATIONAL RESPONSE CENTER
CAN BE REACHED AT (800)424-8802.
PROTECTIVE MEASURES:
AVOID CONTACT WITH SPILLED MATERIAL. SEE SECTION 5 FOR FIRE FIGHTING
INFORMATION. SEE THE HAZARD IDENTIFICATION SECTION FOR SIGNIFICANT HAZARDS.
SEE SECTION 4 FOR FIRST AID ADVICE. SEE SECTION 8 FOR ADVICE ON THE MINIMUM
REQUIREMENTS FOR PERSONAL PROTECTIVE EQUIPMENT. ADDITIONAL PROTECTIVE
MEASURES MAY BE NECESSARY, DEPENDING ON THE SPECIFIC CIRCUMSTANCES AND/OR
THE EXPERT JUDGMENT OF THE EMERGENCY RESPONDERS.
FOR EMERGENCY RESPONDERS:
RESPIRATORY PROTECTION:
RESPIRATORY PROTECTION WILL BE NECESSARY ONLY IN SPECIAL CASES, E.G.,
FORMATION OF MISTS. HALF-FACE OR FULL-FACE RESPIRATOR WITH FILTER(S) FOR
DUST/ORGANIC VAPOR OR SELF CONTAINED BREATHING APPARATUS (SCBA) CAN BE
USED DEPENDING ON THE SIZE OF SPILL AND POTENTIAL LEVEL OF EXPOSURE. IF
THE EXPOSURE CANNOT BE COMPLETELY CHARACTERIZED OR AN OXYGEN DEFICIENT
ATMOSPHERE IS POSSIBLE OR ANTICIPATED, SCBA IS RECOMMENDED. WORK GLOVES
THAT ARE RESISTANT TO HYDROCARBONS ARE RECOMMENDED. GLOVES MADE OF
POLYVINYL ACETATE (PVA) ARE NOT WATER-RESISTANT AND ARE NOT SUITABLE FOR
EMERGENCY USE. CHEMICAL GOGGLES ARE RECOMMENDED IF SPLASHES OR CONTACT
WITH EYES IS POSSIBLE.
SMALL SPILLS: NORMAL ANTISTATIC WORK CLOTHES ARE USUALLY ADEQUATE.
LARGE SPILLS:
FULL BODY SUIT OF CHEMICAL RESISTANT, ANTISTATIC MATERIAL IS RECOMMENDED.
SPILL MANAGEMENT:
LAND SPILL:
STOP LEAK IF YOU CAN DO IT WITHOUT RISK. RECOVER BY PUMPING OR WITH
SUITABLE ABSORBENT.
WATER SPILL:
STOP LEAK IF YOU CAN DO IT WITHOUT RISK. SEEK ADVICE OF A SPECIALIST THIS
PRODUCT EMULSIFIES, DISPERSES OR IS MISCIBLE IN WATER.
WATER SPILL AND LAND SPILL RECOMMENDATIONS ARE BASED ON THE MOST LIKELY
SPILL SCENARIO FOR THIS MATERIAL; HOWEVER, GEOGRAPHIC CONDITIONS, WIND,
TEMPERATURE, (AND IN THE CASE OF A WATER SPILL) WAVE AND CURRENT
DIRECTION AND SPEED MAY GREATLY INFLUENCE THE APPROPRIATE ACTION TO BE
TAKEN. FOR THIS REASON, LOCAL EXPERTS SHOULD BE CONSULTED.
NOTE: LOCAL REGULATIONS MAY PRESCRIBE OR LIMIT ACTION TO BE TAKEN.
ENVIRONMENTAL PRECAUTIONS:
LARGE SPILLS:
DIKE FAR AHEAD OF LIQUID SPILL FOR LATER RECOVERY AND DISPOSAL. PREVENT
ENTRY INTO WATERWAYS, SEWERS, BASEMENTS OR CONFINED AREAS.
| SECTION 7 HANDLING AND STORAGE | |
HANDLING:
AVOID BREATHING MISTS OR VAPORS. AVOID CONTACT WITH SKIN. SMALL METAL
PARTICLES FROM MACHINING MAY CAUSE ABRASION OF THE SKIN AND MAY PREDISPOSE
TO DERMATITIS. PREVENT SMALL SPILLS AND LEAKAGE TO AVOID SLIP HAZARD.
MATERIAL CAN ACCUMULATE STATIC CHARGES WHICH MAY CAUSE AN ELECTRICAL SPARK
(IGNITION SOURCE). WHEN THE MATERIAL IS HANDLED IN BULK, AN ELECTRICAL
SPARK COULD IGNITE ANY FLAMMABLE VAPORS FROM LIQUIDS OR RESIDUES THAT MAY
BE PRESENT (E.G., DURING SWITCH-LOADING OPERATIONS). USE PROPER BONDING
AND/OR GROUND PROCEDURES. HOWEVER, BONDING AND GROUNDS MAY NOT ELIMINATE
THE HAZARD FROM STATIC ACCUMULATION. CONSULT LOCAL APPLICABLE STANDARDS
FOR GUIDANCE. ADDITIONAL REFERENCES INCLUDE AMERICAN PETROLEUM INSTITUTE
2003 (PROTECTION AGAINST IGNITIONS ARISING OUT OF STATIC, LIGHTNING AND
STRAY CURRENTS) OR NATIONAL FIRE PROTECTION AGENCY 77 (RECOMMENDED
PRACTICE ON STATIC ELECTRICITY) OR CENELEC CLC/TR 50404
(ELECTROSTATICS - CODE OF PRACTICE FOR THE AVOIDANCE OF HAZARDS DUE TO
STATIC ELECTRICITY).
STATIC ACCUMULATOR: THIS MATERIAL IS A STATIC ACCUMULATOR.
STORAGE:
THE CONTAINER CHOICE, FOR EXAMPLE STORAGE VESSEL, MAY EFFECT STATIC
ACCUMULATION AND DISSIPATION. DO NOT STORE IN OPEN OR UNLABELLED
CONTAINERS.
| SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION | |
EXPOSURE LIMIT VALUES:
EXPOSURE LIMITS/STANDARDS (NOTE: EXPOSURE LIMITS ARE NOT ADDITIVE):
SUBSTANCE NAME FORM LIMIT / STANDARD NOTE SOURCE
SEVERELY INHALABLE TWA 5 MG/M3 N/A ACGIH
HYDROTREATED HEAVY FRACTION.
PARAFFINIC
DISTILLATE
SEVERELY MIST. TWA 5 MG/M3 N/A ACGIH
HYDROTREATED HEAVY
PARAFFINIC
DISTILLATE
SOLVENT DEWAXED MIST. TWA 5 MG/M3 N/A OSHA Z1
HEAVY PARAFFINIC
DISTILLATE
SOLVENT DEWAXED TWA 2000 500 N/A OSHA Z1
HEAVY PARAFFINIC MG/M3 PPM
DISTILLATE
SOLVENT DEWAXED MIST. TWA 5 MG/M3 N/A ACGIH
HEAVY PARAFFINIC
DISTILLATE
EXPOSURE LIMITS/STANDARDS FOR MATERIALS THAT CAN BE FORMED WHEN HANDLING
THIS PRODUCT:
WHEN MISTS/AEROSOLS CAN OCCUR THE FOLLOWING ARE RECOMMENDED:
5 MG/M3 - ACGIH TLV (INHALABLE FRACTION), 5 MG/M3 - OSHA PEL.
NOTE:
LIMITS/STANDARDS SHOWN FOR GUIDANCE ONLY. FOLLOW APPLICABLE REGULATIONS.
NO BIOLOGICAL LIMITS ALLOCATED.
ENGINEERING CONTROLS:
THE LEVEL OF PROTECTION AND TYPES OF CONTROLS NECESSARY WILL VARY DEPENDING
UPON POTENTIAL EXPOSURE CONDITIONS. CONTROL MEASURES TO CONSIDER:
NO SPECIAL REQUIREMENTS UNDER ORDINARY CONDITIONS OF USE AND WITH ADEQUATE
VENTILATION.
PERSONAL PROTECTION:
PERSONAL PROTECTIVE EQUIPMENT SELECTIONS VARY BASED ON POTENTIAL EXPOSURE
CONDITIONS SUCH AS APPLICATIONS, HANDLING PRACTICES, CONCENTRATION AND
VENTILATION. INFORMATION ON THE SELECTION OF PROTECTIVE EQUIPMENT FOR USE
WITH THIS MATERIAL, AS PROVIDED BELOW, IS BASED UPON INTENDED, NORMAL
USAGE.
RESPIRATORY PROTECTION:
IF ENGINEERING CONTROLS DO NOT MAINTAIN AIRBORNE CONTAMINANT
CONCENTRATIONS AT A LEVEL WHICH IS ADEQUATE TO PROTECT WORKER HEALTH, AN
APPROVED RESPIRATOR MAY BE APPROPRIATE. RESPIRATOR SELECTION, USE, AND
MAINTENANCE MUST BE IN ACCORDANCE WITH REGULATORY REQUIREMENTS, IF
APPLICABLE. TYPES OF RESPIRATORS TO BE CONSIDERED FOR THIS MATERIAL
INCLUDE:
PARTICULATE AIR-PURIFYING RESPIRATOR APPROVED FOR DUST / OIL MIST IS
RECOMMENDED.
FOR HIGH AIRBORNE CONCENTRATIONS, USE AN APPROVED SUPPLIED-AIR RESPIRATOR,
OPERATED IN POSITIVE PRESSURE MODE. SUPPLIED AIR RESPIRATORS WITH AN
ESCAPE BOTTLE MAY BE APPROPRIATE WHEN OXYGEN LEVELS ARE INADEQUATE,
GAS/VAPOR WARNING PROPERTIES ARE POOR, OR IF AIR PURIFYING FILTER
CAPACITY/RATING MAY BE EXCEEDED.
HAND PROTECTION:
ANY SPECIFIC GLOVE INFORMATION PROVIDED IS BASED ON PUBLISHED LITERATURE
AND GLOVE MANUFACTURER DATA. GLOVE SUITABILITY AND BREAKTHROUGH TIME WILL
DIFFER DEPENDING ON THE SPECIFIC USE CONDITIONS. CONTACT THE GLOVE
MANUFACTURER FOR SPECIFIC ADVICE ON GLOVE SELECTION AND BREAKTHROUGH TIMES
FOR YOUR USE CONDITIONS. INSPECT AND REPLACE WORN OR DAMAGED GLOVES. THE
TYPES OF GLOVES TO BE CONSIDERED FOR THIS MATERIAL INCLUDE:
CHEMICAL RESISTANT GLOVES ARE RECOMMENDED.
EYE PROTECTION:
IF CONTACT IS LIKELY, SAFETY GLASSES WITH SIDE SHIELDS ARE RECOMMENDED.
CHEMICAL TYPE GOGGLES SHOULD BE WORN DURING MISTING OPERATIONS.
SKIN AND BODY PROTECTION:
ANY SPECIFIC CLOTHING INFORMATION PROVIDED IS BASED ON PUBLISHED
LITERATURE OR MANUFACTURER DATA. THE TYPES OF CLOTHING TO BE CONSIDERED
FOR THIS MATERIAL INCLUDE:
CHEMICAL/OIL RESISTANT CLOTHING IS RECOMMENDED.
SPECIFIC HYGIENE MEASURES:
ALWAYS OBSERVE GOOD PERSONAL HYGIENE MEASURES, SUCH AS WASHING AFTER
HANDLING THE MATERIAL AND BEFORE EATING, DRINKING, AND/OR SMOKING.
ROUTINELY WASH WORK CLOTHING AND PROTECTIVE EQUIPMENT TO REMOVE
CONTAMINANTS. DISCARD CONTAMINATED CLOTHING AND FOOTWEAR THAT CANNOT
BE CLEANED. PRACTICE GOOD HOUSEKEEPING.
ENVIRONMENTAL CONTROLS:
COMPLY WITH APPLICABLE ENVIRONMENTAL REGULATIONS LIMITING DISCHARGE TO
AIR, WATER AND SOIL. PROTECT THE ENVIRONMENT BY APPLYING APPROPRIATE
CONTROL MEASURES TO PREVENT OR LIMIT EMISSIONS.
| SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES | |
NOTE:
PHYSICAL AND CHEMICAL PROPERTIES ARE PROVIDED FOR SAFETY, HEALTH AND
ENVIRONMENTAL CONSIDERATIONS ONLY AND MAY NOT FULLY REPRESENT PRODUCT
SPECIFICATIONS. CONTACT THE SUPPLIER FOR ADDITIONAL INFORMATION.
GENERAL INFORMATION:
PHYSICAL STATE: LIQUID
COLOR: YELLOW
ODOR: CHARACTERISTIC
ODOR THRESHOLD: N/D
IMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATION:
RELATIVE DENSITY (AT 15 DEG. C): 0.89
FLAMMABILITY (SOLID, GAS): N/A
FLASH POINT [METHOD]: >179 DEG. C (354 DEG. F) [ASTM D-92]
FLAMMABLE LIMITS (APPROXIMATE VOLUME % IN AIR):
LEL: N/D
UEL: N/D
AUTOIGNITION TEMPERATURE: N/D
BOILING POINT / RANGE:
270 DEG. C (518 DEG. F) - 500 DEG. C (932 DEG. F) [ESTIMATED]
DECOMPOSITION TEMPERATURE: N/D
VAPOR DENSITY (AIR = 1): >2 AT 101 KPA [ESTIMATED]
VAPOR PRESSURE:
[N/D AT 20 DEG. C]
<1 KPA (7.5 MMHg) AT 38 DEG. C
EVAPORATION RATE (N-BUTYL ACETATE = 1): <0.1
PH: N/A
LOG POW (N-OCTANOL/WATER PARTITION COEFFICIENT): N/D
SOLUBILITY IN WATER: EMULSIFIES
VISCOSITY: 35 CST (35 MM2/SEC) AT 40 DEG. C
OXIDIZING PROPERTIES: SEE HAZARDS IDENTIFICATION SECTION.
OTHER INFORMATION:
FREEZING POINT: N/D
MELTING POINT: N/A
POUR POINT: -6 DEG. C (21 DEG. F)
DMSO EXTRACT (MINERAL OIL ONLY), IP-346: <3 %WT
| SECTION 10 STABILITY AND REACTIVITY | |
REACTIVITY: SEE SUB-SECTIONS BELOW.
STABILITY: MATERIAL IS STABLE UNDER NORMAL CONDITIONS.
CONDITIONS TO AVOID:
HIGH ENERGY SOURCES OF IGNITION., HEAT/ FREEZING TEMPERATURES.
MATERIALS TO AVOID: STRONG OXIDIZERS
HAZARDOUS DECOMPOSITION PRODUCTS:
MATERIAL DOES NOT DECOMPOSE AT AMBIENT TEMPERATURES.
POSSIBILITY OF HAZARDOUS REACTIONS:
HAZARDOUS POLYMERIZATION WILL NOT OCCUR.
| SECTION 11 TOXICOLOGICAL INFORMATION | |
INFORMATION ON TOXICOLOGICAL EFFECTS:
HAZARD CLASS CONCLUSION / REMARKS
INHALATION:
ACUTE TOXICITY:
NO END POINT DATA FOR MATERIAL. MINIMALLY TOXIC. BASED ON ASSESSMENT
OF THE COMPONENTS.
IRRITATION:
NO END POINT DATA FOR MATERIAL. ELEVATED TEMPERATURES OR MECHANICAL
ACTION MAY FORM VAPORS, MIST, OR
FUMES WHICH MAY BE IRRITATING TO
THE EYES, NOSE, THROAT, OR LUNGS.
INGESTION:
ACUTE TOXICITY:
NO END POINT DATA FOR MATERIAL. MINIMALLY TOXIC. BASED ON ASSESSMENT
OF THE COMPONENTS.
SKIN:
ACUTE TOXICITY:
NO END POINT DATA FOR MATERIAL. MINIMALLY TOXIC. BASED ON ASSESSMENT
OF THE COMPONENTS.
SKIN CORROSION/IRRITATION:
DATA AVAILABLE. NEGLIGIBLE IRRITATION TO SKIN AT
AMBIENT TEMPERATURES. BASED ON TEST
DATA FOR THE MATERIAL. TEST(S)
EQUIVALENT OR SIMILAR TO OECD
GUIDELINE 404
EYE:
SERIOUS EYE DAMAGE/IRRITATION:
DATA AVAILABLE. MAY CAUSE MILD, SHORT-LASTING
DISCOMFORT TO EYES. BASED ON TEST
DATA FOR THE MATERIAL. TEST(S)
EQUIVALENT OR SIMILAR TO OECD
GUIDELINE 405
SENSITIZATION:
RESPIRATORY SENSITIZATION:
NO END POINT DATA FOR MATERIAL. NOT EXPECTED TO BE A RESPIRATORY
SENSITIZER.
SKIN SENSITIZATION:
NO END POINT DATA FOR MATERIAL. CONTAINS A SUBSTANCE THAT MAY
CAUSE SKIN SENSITIZATION. BASED ON
ASSESSMENT OF THE COMPONENTS.
ASPIRATION:
DATA AVAILABLE. NOT EXPECTED TO BE AN ASPIRATION
HAZARD. BASED ON PHYSICO-CHEMICAL
PROPERTIES OF THE MATERIAL.
GERM CELL MUTAGENICITY:
NO END POINT DATA FOR MATERIAL. NOT EXPECTED TO BE A GERM CELL
MUTAGEN. BASED ON ASSESSMENT OF
THE COMPONENTS.
CARCINOGENICITY:
NO END POINT DATA FOR MATERIAL. NOT EXPECTED TO CAUSE CANCER. BASED
ON ASSESSMENT OF THE COMPONENTS.
REPRODUCTIVE TOXICITY:
NO END POINT DATA FOR MATERIAL. NOT EXPECTED TO BE A REPRODUCTIVE
TOXICANT. BASED ON ASSESSMENT OF
THE COMPONENTS.
LACTATION:
NO END POINT DATA FOR MATERIAL. NOT EXPECTED TO CAUSE HARM TO
BREAST-FED CHILDREN.
SPECIFIC TARGET ORGAN TOXICITY
(STOT):
SINGLE EXPOSURE:
NO END POINT DATA FOR MATERIAL. NOT EXPECTED TO CAUSE ORGAN DAMAGE
FROM A SINGLE EXPOSURE.
REPEATED EXPOSURE:
NO END POINT DATA FOR MATERIAL. NOT EXPECTED TO CAUSE ORGAN DAMAGE
FROM PROLONGED OR REPEATED EXPOSURE.
BASED ON ASSESSMENT OF THE
COMPONENTS.
OTHER INFORMATION:
FOR THE PRODUCT ITSELF:
AN INGREDIENT OR INGREDIENTS THAT ARE CLASSIFIED AS A SKIN SENSITIZER.
CONTAINS:
BASE OIL SEVERELY REFINED:
NOT CARCINOGENIC IN ANIMAL STUDIES. REPRESENTATIVE MATERIAL PASSES IP-346,
MODIFIED AMES TEST, AND/OR OTHER SCREENING TESTS. DERMAL AND INHALATION
STUDIES SHOWED MINIMAL EFFECTS; LUNG NON-SPECIFIC INFILTRATION OF IMMUNE
CELLS, OIL DEPOSITION AND MINIMAL GRANULOMA FORMATION. NOT SENSITIZING
IN TEST ANIMALS.
THE FOLLOWING INGREDIENTS ARE CITED ON THE LISTS BELOW: NONE.
REGULATORY LISTS SEARCHED:
1 = NTP CARC
2 = NTP SUS
3 = IARC 1
4 = IARC 2A
5 = IARC 2B
6 = OSHA CARC
| SECTION 12 ECOLOGICAL INFORMATION | |
THE INFORMATION GIVEN IS BASED ON DATA AVAILABLE FOR THE MATERIAL, THE
COMPONENTS OF THE MATERIAL, AND SIMILAR MATERIALS.
ECOTOXICITY:
MATERIAL: EXPECTED TO BE HARMFUL TO AQUATIC ORGANISMS.
PERSISTENCE AND DEGRADABILITY:
BIODEGRADATION:
BASE OIL COMPONENT: EXPECTED TO BE INHERENTLY BIODEGRADABLE
OTHER ECOLOGICAL INFORMATION:
VOC: 10.2 G/L [ASTM E1868-10]
| SECTION 13 DISPOSAL CONSIDERATIONS | |
DISPOSAL RECOMMENDATIONS BASED ON MATERIAL AS SUPPLIED. DISPOSAL MUST BE
IN ACCORDANCE WITH CURRENT APPLICABLE LAWS AND REGULATIONS, AND MATERIAL
CHARACTERISTICS AT TIME OF DISPOSAL.
DISPOSAL RECOMMENDATIONS:
PRODUCT IS SUITABLE FOR BURNING IN AN ENCLOSED CONTROLLED BURNER FOR FUEL
VALUE OR DISPOSAL BY SUPERVISED INCINERATION AT VERY HIGH TEMPERATURES TO
PREVENT FORMATION OF UNDESIRABLE COMBUSTION PRODUCTS.
REGULATORY DISPOSAL INFORMATION:
RCRA INFORMATION: THE UNUSED PRODUCT, IN OUR OPINION, IS NOT SPECIFICALLY
LISTED BY THE EPA AS A HAZARDOUS WASTE (40 CFR, PART 261D), NOR IS IT
FORMULATED TO CONTAIN MATERIALS WHICH ARE LISTED AS HAZARDOUS WASTES. IT
DOES NOT EXHIBIT THE HAZARDOUS CHARACTERISTICS OF IGNITABILITY,
CORROSITIVITY OR REACTIVITY AND IS NOT FORMULATED WITH CONTAMINANTS AS
DETERMINED BY THE TOXICITY CHARACTERISTIC LEACHING PROCEDURE (TCLP).
HOWEVER, USED PRODUCT MAY BE REGULATED.
EMPTY CONTAINER WARNING:
EMPTY CONTAINER WARNING (WHERE APPLICABLE):
EMPTY CONTAINERS MAY CONTAIN RESIDUE AND CAN BE DANGEROUS. DO NOT ATTEMPT
TO REFILL OR CLEAN CONTAINERS WITHOUT PROPER INSTRUCTIONS. EMPTY DRUMS
SHOULD BE COMPLETELY DRAINED AND SAFELY STORED UNTIL APPROPRIATELY
RECONDITIONED OR DISPOSED. EMPTY CONTAINERS SHOULD BE TAKEN FOR RECYCLING,
RECOVERY, OR DISPOSAL THROUGH SUITABLY QUALIFIED OR LICENSED CONTRACTOR
AND IN ACCORDANCE WITH GOVERNMENTAL REGULATIONS. DO NOT PRESSURISE, CUT,
WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE SUCH CONTAINERS TO HEAT,
FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION. THEY MAY
EXPLODE AND CAUSE INJURY OR DEATH.
| SECTION 14 TRANSPORT INFORMATION | |
LAND (DOT): NOT REGULATED FOR LAND TRANSPORT
LAND (TDG): NOT REGULATED FOR LAND TRANSPORT
SEA (IMDG): NOT REGULATED FOR SEA TRANSPORT ACCORDING TO IMDG-CODE
MARINE POLLUTANT: NO
AIR (IATA): NOT REGULATED FOR AIR TRANSPORT
| SECTION 15 REGULATORY INFORMATION | |
OSHA HAZARD COMMUNICATION STANDARD:
THIS MATERIAL IS CONSIDERED HAZARDOUS IN ACCORDANCE WITH OSHA HAZCOM 2012,
29 CFR 1910.1200.
LISTED OR EXEMPT FROM LISTING/NOTIFICATION ON THE FOLLOWING CHEMICAL
INVENTORIES:
DSL, IECSC, TSCA
EPCRA SECTION 302:
THIS MATERIAL CONTAINS NO EXTREMELY HAZARDOUS SUBSTANCES.
SARA (311/312) REPORTABLE HAZARD CATEGORIES: IMMEDIATE HEALTH.
SARA (313) TOXIC RELEASE INVENTORY:
THIS MATERIAL CONTAINS NO CHEMICALS SUBJECT TO THE SUPPLIER NOTIFICATION
REQUIREMENTS OF THE SARA 313 TOXIC RELEASE PROGRAM.
THE FOLLOWING INGREDIENTS ARE CITED ON THE LISTS BELOW: NONE.
REGULATORY LISTS SEARCHED:
1 = ACGIH ALL
2 = ACGIH A1
3 = ACGIH A2
4 = OSHA Z
5 = TSCA 4
6 = TSCA 5A2
7 = TSCA 5E
8 = TSCA 6
9 = TSCA 12B
10 = CA P65 CARC
11 = CA P65 REPRO
12 = CA RTK
13 = IL RTK
14 = LA RTK
15 = MI 293
16 = MN RTK
17 = NJ RTK
18 = PA RTK
19 = RI RTK
CODE KEY:
CARC=CARCINOGEN;
REPRO=REPRODUCTIVE
| SECTION 16 OTHER INFORMATION | |
N/D = NOT DETERMINED,
N/A = NOT APPLICABLE
KEY TO THE H-CODES CONTAINED IN SECTION 3 OF THIS DOCUMENT (FOR
INFORMATION ONLY):
H302: HARMFUL IF SWALLOWED; ACUTE TOX ORAL, CAT 4
H304: MAY BE FATAL IF SWALLOWED AND ENTERS AIRWAYS; ASPIRATION, CAT 1
H315: CAUSES SKIN IRRITATION; SKIN CORR/IRRITATION, CAT 2
H317: MAY CAUSE ALLERGIC SKIN REACTION; SKIN SENSITIZATION, CAT 1
H318: CAUSES SERIOUS EYE DAMAGE; SERIOUS EYE DAMAGE/IRR, CAT 1
H319(2A): CAUSES SERIOUS EYE IRRITATION; SERIOUS EYE DAMAGE/IRR, CAT 2A
H400: VERY TOXIC TO AQUATIC LIFE; ACUTE ENV TOX, CAT 1
THIS SAFETY DATA SHEET CONTAINS THE FOLLOWING REVISIONS:
UPDATES MADE IN ACCORDANCE WITH IMPLEMENTATION OF GHS REQUIREMENTS.
THE INFORMATION AND RECOMMENDATIONS CONTAINED HEREIN ARE, TO THE BEST OF
EXXONMOBIL'S KNOWLEDGE AND BELIEF, ACCURATE AND RELIABLE AS OF THE DATE
ISSUED. YOU CAN CONTACT EXXONMOBIL TO INSURE THAT THIS DOCUMENT IS THE
MOST CURRENT AVAILABLE FROM EXXONMOBIL. THE INFORMATION AND
RECOMMENDATIONS ARE OFFERED FOR THE USER'S CONSIDERATION AND EXAMINATION.
IT IS THE USER'S RESPONSIBILITY TO SATISFY ITSELF THAT THE PRODUCT IS
SUITABLE FOR THE INTENDED USE. IF BUYER REPACKAGES THIS PRODUCT, IT IS
THE USER'S RESPONSIBILITY TO INSURE PROPER HEALTH, SAFETY AND OTHER
NECESSARY INFORMATION IS INCLUDED WITH AND/OR ON THE CONTAINER.
APPROPRIATE WARNINGS AND SAFE-HANDLING PROCEDURES SHOULD BE PROVIDED TO
HANDLERS AND USERS. ALTERATION OF THIS DOCUMENT IS STRICTLY PROHIBITED.
EXCEPT TO THE EXTENT REQUIRED BY LAW, RE-PUBLICATION OR RETRANSMISSION
OF THIS DOCUMENT, IN WHOLE OR IN PART, IS NOT PERMITTED. THE TERM,
"EXXONMOBIL" IS USED FOR CONVENIENCE, AND MAY INCLUDE ANY ONE OR MORE
OF EXXONMOBIL CHEMICAL COMPANY, EXXON MOBIL CORPORATION, OR ANY
AFFILIATES IN WHICH THEY DIRECTLY OR INDIRECTLY HOLD ANY INTEREST.
INTERNAL USE ONLY:
MHC: 0, 0, 0, 0, 0, 1
PPEC: A
DGN: 7108394XUS (1019376)
COPYRIGHT 2002 EXXON MOBIL CORPORATION, ALL RIGHTS RESERVED